Search

Purpose: To evaluate the marginal and internal fit of endocrowns with different computer-aided design/computer-aided manufacturing (CAD-CAM) materials by measuring them with a stereomicroscope (μm). Materials and Methods: A mandibular first molar typodont tooth was prepared to receive an endocrown. The preparation was scanned using an extra-oral scanner. Endocrowns (n = 20) were fabricated using lithium disilicate (IPS e. max CAD LT block; CEREC Ivoclar Vivadent, Liechtenstein) and polyetheretherketone (PEEK) (breCAM. BioHPP®; Bredent, UK) using CAD-CAM technique. Marginal gap was evaluated using a stereomicroscope at the midpoint of all four surfaces (mid buccal, mid lingual, mid mesial, mid distal). This was followed by sectioning of the endocrowns in a sagittal plane along with the prepared tooth to evaluate the internal fit at four different points (A, B, C, D) using a stereomicroscope. Statistical analysis was performed using one-way analysis of variance test. Results: Mean values of marginal gap of lithium disilicate and PEEK endocrowns are 56.6 ± 6.1 μm and 81.3 ± 10.1 μm, respectively. Mean value internal gaps of lithium disilicate and PEEK endocrowns are 158.2 ± 11.1 μm and 199.1 ± 13 μm, respectively. Results in the present study have shown that the marginal and internal fits of lithium disilicate endocrowns are superior to that of PEEK endocrowns. Conclusions: Based on the outcomes of this in vitro study, the marginal and internal fit of lithium disilicate endocrowns is better than PEEK endocrowns. The marginal gap clinically acceptable is

Background/purpose The orthodontic aligner becomes popular worldwide in orthodontic therapy as an esthetic alternative to fixed labial braces. This study evaluated orthodontic tooth movement behavior using different aligner materials and attachment shapes for the movement of a single tooth. Materials and methods First bicuspid extracted resin typodont models were printed with a 3D printer. Three type of attachments, an ellipsoid shape (thick and thin) and a bar, were designed to fit the canine crown surface. Three types of aligner materials, Polyethylene Terephthalate enhanced with glycol (BIOSTAR) Polyethylene Terephthalate (BenQ), and Thermoplastic polyurethanes (TPU) were used to fabricate different aligners. The typodonts with aligners were sunk in a water bath to simulate canine distal movement in vivo. The canine crown, root movement, and long axis angle changes in each step were calculated and recorded. The data were analysed using a oneway ANOVA statistical method. Results Comparing the three aligners, the changes the long axis of the canine showed that the BENQ group had a smaller change in the long axis angle. The BENQ group canine involved bodily movement, but the canine movement of the BIOSTAR and TPU group involved tipping. Comparing the three attachments, the bar type attachment had more canine crown tipping in the BIOSTAR and TPU groups. The thick and thin ellipsoid-shaped attachments showed no statistical differences in tooth movement. Conclusion Attachment shape or size had little influence on the bodily movement of the tooth. A high modulus material may thus be suitable for clinical applications.

Background/purpose: With the rise of digitalization in dentistry, intraoral scanners and digital impressions have recently been adopted by many clinicians. The aim of this study was to investigate surface topography of prepared teeth and the accuracy of digital impressions. Materials and methods: Twenty mandibular typodonts, containing left first premolar and left first molar abutment teeth manufactured by using CAD/CAM, were used in this study. An intraoral scanner was used to scan each typodont, and each STL file generated was exported in high resolution (Group H), moderate resolution (Group M), and low resolution (Group L). All 60 files were inspected in a 3-D mesh processing software. For each file, the number of triangulation points in the meshwork were obtained for both abutment teeth. Results: The measurements obtained from the 3-D mesh processing software revealed that the mean number of triangulation points on the 3-D surface of the abutment teeth (20 premolars + 20 M) were 790,625 ± 98,890 dots in Group H, 592,283 ± 74,881 dots in Group M, and 198,067 ± 19,328 dots in Group L. Significant differences were found between Group H and M (p

Background In restorative dentistry, the use of high-speed air turbine, which generates aerosols, can be associated with the transmission of airborne diseases. New laser technologies could be useful in reducing the amount of aerosols, but there is a lack of scientific research on this topic. Material and methods This is a descriptive study to analyze the amount of aerosols produced after class I cavity preparation using high-speed air turbine (group 1) and Er,Cr:YSGG laser with two different parameters (groups 2 and 3). Fluorescein dye was incorporated into the coolant reservoir in order to visualize the production of aerosols during each procedure. Tooth preparation was performed in a typodont with human lower molar tooth under rubber dam isolation. The procedure was carried out in a transparent plastic box to avoid aerosols dispersion. Sixteen grade I cellulose filter discs were distributed along the surfaces of the box. The area contaminated with aerosols in the filters was measured using ultraviolet illumination. Results In group 1, the contaminated surface area covered with fluorescein dye reached 77.3% (1349 cm2) of the total; in group 2 (laser with 80% water) we observed 7.3% (128 cm2) and in group 3 (laser with 40% water) it was 3.8% (68 cm2). The reduction in water parameter from 80% to 40% coincided with 48% reduction of the contaminated area on the filter discs. Focusing on the surfaces of the box, we noted that the mean contamination on the left side was more than on the right side in all three experimental groups. In group 1 using air turbine, we measured a mean of 102.6[±7.5 SD]cm2 on the left side, compared to 70.6[±32.3 SD]cm2 on the right side. In laser groups 2 and 3, a mean of 12.8[±14.9 SD]cm2 and 6.8 [±5.7SD]cm2, respectively, was described on the left surface versus 0 cm2 of surface contamination on the right surface. Conclusions The contaminated area during the procedure of class I cavity preparation, is reduced by 70% using Er,Cr:YSGG laser compared to high-speed turbine. A slightly higher contamination was observed between laser groups with 80% versus 40% water. The use of Er,Cr:YSGG laser in restorative dentistry can be a valid treatment alternative to reduce aerosols production compared to conventional high-speed rotary instruments. Key words:Er,Cr:YSGG laser, Aerosols, SARS-CoV-2, Rotary instruments, conservative dentistry.

Statement of problem Whether the precision of fit of computer-aided design and computer-aided manufacturing (CAD-CAM) complete crowns is affected by the finish line configuration is unclear. Purpose The purpose of this in vitro study was to evaluate the marginal and internal fit of CAD-CAM ceramic crowns made from lithium disilicate based on 3 different finish lines (rounded shoulder, chamfer, feather-edge). Materials and methods Thirty anterior lithium disilicate complete crowns (n=10 per finish line group) were fabricated by following a completely digital workflow based on digital scans made with the TRIOS scanner. The crowns were adhesively cemented on duplicate dies of the respective prepared Typodont teeth, and the marginal gap, absolute marginal discrepancy, and internal gap were evaluated by using microcomputed tomography (μCT). A total of 66 values were obtained for each specimen from sagittal and transaxial sections, and a rendering software program was used to calculate the volume of the cement gap for each specimen by means of 3D region growing. Two-way ANOVA, Tukey post hoc tests with Bonferroni correction, and the Kruskal-Wallis test were used to compare the values between the experimental groups (α=.05). Results Marginal gap and absolute marginal discrepancy values were statistically significantly different between groups. In ascending order, marginal gap values were 23 ±14 μm for rounded shoulder, 54 ±28 μm for chamfer, and 96 ±36 μm for feather-edge finish lines. Absolute marginal discrepancy values were 96 ±34 μm for rounded shoulder, 124 ±37 μm for chamfer, and 157 ±34 μm for feather-edge finish lines. Internal gap values were 111 ±14 μm for feather-edge, 136 ±22 μm for chamfer, and 168 ±25 μm for rounded shoulder finish lines. The differences in cement volume between groups were not statistically significant (P=.200). Conclusions All 3 finish lines produced marginal gaps within the range of clinically accep table values. Lithium disilicate CAD crowns with a rounded shoulder finish line had the best marginal fit but the poorest internal fit, and lithium disilicate CAD crowns with a feather-edge finish line had the best internal fit but the poorest marginal fit.

Background and Objectives: One of the important steps toward achieving a successful fixed partial denture treatment is the fabrication of interim restorations with good marginal adaptation. Poor marginal adaptation of the interim restorations will allow ingress of fluids and microorganisms between the restorations and may lead to caries and pulpitis. The objective of this study was to evaluate and compare the marginal accuracy of interim restorations made from two polymethyl methacrylate (PMMA) and two bis-acryl materials. Materials and Methods: An in vitro method was used to replicate a clinical procedure in which the interim crown was made using a direct technique. A maxillary first molar typodont tooth was prepared to receive a full cast crown restoration having 1 mm chamfer and a taper of 5°, and then the prepared artificial tooth was cast into a cobalt chromium metal die. Wax patterns were prepared on the metal die using type 2 inlay wax for full metal crowns. The impression of the die along with the wax pattern was made with a putty-type polyvinyl siloxane, and this impression was used as a mold for making interim restorations. Two PMMA and two bis-acryl provisional crown materials were distributed as follows: Group A: Unifast Trad (GC Dental), Group B: DPI self-cure tooth molding material, Group C: Structur 2 QM (VOCO), and Group D: Cool Temp Natural (Coltene/Whaledent). A total of 60 interim restorations from all the four materials were fabricated (15 interim restorations from each material). The marginal discrepancy of the interim restoration was determined by measuring the space between the margin of the interim restoration and the finish line of the metal die at four vertical reference lines previously marked at the midpoint of the metal die finish line at the buccal, palatal, mesial, and distal surfaces of the die. The marginal gaps were visualized at ×45 magnification using a stereomicroscope and interpreted using ProgRes image capture software. Results: The mean marginal discrepancy calculated in PMMA materials was 269 µm for DPI and 205 µm for Unifast Trad, and the mean marginal gap for the bis-acryl material was 171 µm for Cool Temp and 140 µm for Structur 2 QM. Interpretation and Conclusion: Comparison of marginal accuracy showed that bis-acryl provisional crown material showed better marginal accuracy than PMMA provisional crown material. Among the materials tested, Structur 2 QM showed the best marginal accuracy, and the least marginal accuracy was shown by DPI.

PURPOSE To investigate the trueness and marginal fit of computer-aided design-computer-aided manufactured (CAD-CAM) complete-arch implant-supported screw-retained fixed prosthesis (CAISFP) made of polyetheretherketone (PEEK), polyetherketoneketone (PEKK) and titanium (Ti) MATERIAL AND METHODS: A typodont model with four implants, their multiunit abutments (MUAs), and MUA scanbodies were digitized by using a laboratory scanner. The generated CAD was used to mill CAISFP frameworks in Ti, PEEK, or PEKK (each n = 10). The frameworks were digitized with an industrial light scanner to superimpose resulting standard tessellation language (STL) file with the CAD file. Deviations at five points at the abutment-framework interface of each of the four abutment sites (1:left first molar, 2:left canine, 3:right canine, 4:right first molar sites) were calculated (trueness). Marginal gaps were measured using the triple scan technique. A nonparametric repeated measures ANOVA by Brunner and Puri with factors being abutment location and material was performed to assess the mean deviations for trueness and mean marginal gaps, followed by Mann-Whitney or exact Wilcoxon Signed-Rank tests (alpha=.05). RESULTS Material type significantly affected the trueness (p

Background/purpose: En masse retraction was still controversy in orthodontics. The aim of this study was to investigate the effect of force directions created by different miniscrew positions and lever arm heights on maxillary central incisor movement using Finite Element (FE) simulation and a Typodont model. Materials and methods: A typodont model and 3-dimensional FE were used to simulate en masse anterior teeth retraction in sliding mechanics. The lever arm and the miniscrew positions were varied to change the force direction. The maxillary central incisor displacement was recorded and analyzed. Results: The typodont results revealed that miniscrew vertical position and lever arm height affected the type of tooth movement. The best control in the vertical plane was achieved by a 7 mm lever arm height and miniscrew 9 mm from the archwire. When the lever arm height and miniscrew were 7 mm from the archwire, the tooth extruded. When the lever arm height was 9 mm and the miniscrew was 7 or 9 mm from the archwire, the tooth intruded. The FE stimulation determined that near bodily movement of the maxillary central incisor was achieved when the lever arm height and miniscrew was 9 mm from the archwire. The highest strain distribution in the periodontal ligament was observed at the apical third of the lateral incisor. Conclusion: In en masse retraction, the appropriate direction of force or the height of the miniscrew and the lever arm may enable orthodontists to maintain better control of the anterior teeth in sliding mechanics. Keywords: En masse retraction, Finite element, Lever arm, Miniscrew, Typodont

Aim: The aim of the study was to evaluate and compare the vertical marginal discrepancy of computer-aided design (CAD)/computer-aided manufacturing (CAM) and pressable lithium disilicate onlays. Materials and Methods: A maxillary first premolar typodont tooth was prepared to receive lithium disilicate onlay. Mesio-occluso-distal cavity was prepared with palatal cusp reduction and collar preparation. In the proximal box, gingival seat was placed 1 mm coronal to the cementoenamel junction and mesiodistal width of the seat was kept to 1 mm. Thirty stone models were prepared from thirty rubber base impressions and divided into two groups, based on the technique of fabrication of onlays: (1) Group CL (CAD/CAM lithium disilicate) and (2) Group PL (Pressable lithium disilicate). Fifteen onlays per each group were fabricated by following the manufacturer instructions. Marginal fit of all the samples were analyzed by using stereomicroscope with Image Analysis software. Statistical analysis was done by t-test. Results: Statistical significant difference was found between both the groups. The lowest marginal discrepancy (41.46 μm) was measured for Group CL (CAD/CAM lithium disilicate) specimens, and the highest (55.95 μm) discrepancy was observed on the Group PL (Pressable lithium disilicate) specimens. Conclusion: Although there was a statistically significant difference between the two groups, marginal gap of both the groups were in clinically acceptable levels.

As an innovative approach to overcome the rate-limiting staging of conventional aligners, using shape memory polymers (SMPs) as aligners’ materials was investigated in this in vitro study. The ability of SMPs to shape recover and consequently move tooth, upon appropriate stimuli, was evaluated on a typodont model before clinical application. The study design was to achieve 1.9 mm correction movement of an upper central incisor by one aligner after multiple steps/activation. A custom-made aligned typodont model with a movable upper central incisor was scanned. Using an orthodontic software and a 3D printer, resin-models were generated. Seven aligners of ClearX sheets (SMPs) were fabricated by thermoforming on the resin aligned model. Each aligner was tested for repositioning of the central incisor in the typodont model. The model was scanned after each step and the corrective movement was measured through the superimposition of scans. Results showed that the total correction efficiency of the SMPs’ aligner was ≈93% (1.76 mm). The corrective movement was 0.94 ± 0.04 mm after the reforming step, 0.66 ± 0.07 mm after the first activation step, and 0.15 ± 0.10 mm after the second activation step. It was concluded that aligners made of SMPs could have a promising future-use in orthodontic aesthetic treatment.

[EN] Purpose: To measure the impact of different scanning patches on the accuracy (trueness and precision) of an intraoral scanner (IOS). Material and methods: A typodont was digitized using an industrial optical scanner (GOM Atos Q 3D 12 M) to obtain a reference mesh. The typodont was scanned using an IOS (TRIOS 3). Three groups were generated based on the rescan areas created: no mesh holes (G0 group), 3 mesh holes distributed on the digital scan (G1 group), and 3 mesh holes located on the left quadrant of the digital scan (G2 group). In the G0 group, a digital scan was completed following the manufacturer's scanning protocol. In the G1 group, a digital scan was obtained following the same protocol as G0 group. Three 12-mm diameter holes were created in the occlusal surfaces of the left second first molar, incisal edges of the central incisors, and right first molar of the digital scan using the IOS software. In the G2 group, a digital scan was obtained following the same protocol as G0 group. Three 12mm diameter holes in the digital scan were created in the occlusal surface of the left first molar and left second and first premolars using the IOS software program. The discrepancy between the control and the experimental digital scans was measured using the root mean square calculation. The Kolmogorov-Smirnov test demonstrated that data were normally distributed. One-way ANOVA followed by post hoc multiple comparison Bonferroni test were used to analyze the data (alpha = .05). Results: Trueness values ranged from 15 to 26 mu m and the precision ranged from 21 to 150 mu m. Significant differences in trueness mean values were found among the groups tested (F(2, 42) = 6.622, P = .003); the Bonferroni test indicated significant mean differences between the G0 and G2 groups (mean difference=0.11, SE=0.003, and P = .002). For precision evaluation, significant precision differences were found between the groups tested (F(2, 39)=9.479, P < .001); the Bonferroni test revealed significant precision differences between G0 and G2 groups (mean difference=-0.12, SE=0.030, and P = .001). Conclusions: Rescanning mesh holes and stitching procedures decreased the trueness and precision of the IOS tested; furthermore, the number and dimensions of mesh holes rescanned represented an important factor that influenced the scanning accuracy of IOS tested. Clinical Significance: It is a fundamental procedure obtaining intraoral digital scans without leaving mesh holes, so the rescanning techniques are minimized and, therefore, the scanning accuracy of the intraoral scanner tested is maximized.

Adaptation is an important factor for the clinical success of restorations. However, no studies are available evaluating the adaptation of primary crowns. The aim of this study was to compare the adaptation of crowns fabricated by CAD/CAM technology versus prefabricated fiberglass primary crowns. Typodont maxillary central, canine, and mandibular molar teeth were prepared to serve as master dies after the size of Figaro crowns was determined ( n = 10 ). Master dies were scanned with an intraoral scanner, and 10 identical CAD/CAM crowns were fabricated from resin-ceramic blocks. Figaro and CAD/CAM crowns were placed on the corresponding master dies and scanned via micro-CT. Three-dimensional volumetric gap measurements were performed to evaluate the overall adaptation. A total of 255 location-based linear measurements were allocated into 4 categories: marginal, cervical-axial, middle-axial, and occlusal. Statistical analyses were performed with factorial ANOVA, repeated measure ANOVA, and LSD tests ( α = 0.05 ). CAD/CAM crowns showed significantly lower overall and location-based gap measurements than Figaro crowns regardless of tooth number ( p < 0.05 ). For all groups, mean marginal discrepancies were lower than occlusal measurements ( p < 0.05 ). Both crown types showed higher marginal gaps for molar teeth than for canine and central incisors with no significant difference between them ( p > 0.05 ). CAD/CAM-fabricated crowns showed better marginal and internal adaptation than prefabricated Figaro crowns.

Aim: To compare the accuracy (trueness and precision)of cost-accessible three-dimensional (3D) printed models.Methods: A maxillary typodont (MM) was scanned andprinted 10 times in polylactic acid, resulting in 10 digitalmodels (DMs). Polyvinylsiloxane impressions were made toobtain 10 conventional stone models (SMs). All models werescanned and imported to CloudCompare software. The totalarea and three locations of interest were evaluated (zenith toincisal [Z-I], canine to canine [C-C], and first molar to canine[1M-C] distances). Total area evaluations were performed byaligning the MM and experimental models using the best-fitalgorithm and were compared using the Haussdorf distance.The distances between points of interest were measured usingthe point-picking tool at the same 3D coordinates. The meanvolumetric deviations were considered for trueness analysis.Precision was set as the standard deviation. Statisticaldifferences were evaluated using the Student’s t-test. Results:Total area volumetric comparisons showed that DMs showedsuperior trueness and precision (-0.02 ± 0.03) compared tothe SMs (0.37 ± 0.29) (P < 0.001). No differences between themodels were observed for Z-I (P = .155); however, SMs showedfewer deviations for C-C (P = .035) and 1M-C (P = .001) thanDMs. Conclusions: The DMs presented superior trueness andprecision for total area compared to the SMs; however, the SMswere more accurate when points of interest were evaluated.

The accuracy of newly developed ceramic materials is still being studied. Marginal and internal adaptation are known factors that have an essential impact on the long term success of dental restorations. The aim of this in vitro study was to evaluate the marginal and internal fit of heat-pressed and milled monolithic glass-ceramic restorations based on their ceramic type, processing technique, and in vitro thermocycling. Thirty-two crowns were studied and divided into four groups (n = 8), according to the ceramic material (feldspathic glass-ceramic (F) and zirconia reinforced lithium silicate glass-ceramic (ZLS)) and to their technological obtaining processes (milling (M) and heat-pressing (P)). A typodont preparation was scanned with a D2000 3D scanner to obtain identical 32 resin 3D-printed abutment teeth. Marginal and internal gaps were measured using the silicone replica technique under 40&times, magnification. The crowns were further cemented and thermally aged for 10,000 cycles After cementation and thermocycling of the samples, marginal and internal gaps were assessed using micro-CT (micro-computed tomography)) analysis. Data were statistically analyzed using statistical tests. Significant differences were found before and after cementation and thermocycling among the tested materials (p &lt, 0.05). Related to technological processing, significant differences were seen in the marginal area between FP and FM (p &lt, 0.05) Significant differences were also found in the axial and occlusal areas between the ZLSP and ZLSM. Thermocycling and cementation did not have a significant effect on the tested materials (p &lt, 0.05). The technological processes influenced the marginal and internal fit of the crowns in favor of the CAD/CAM (computer aided design/computer aided manufacturing)technologies. Thermal aging had little effect on marginal adaptability, it increased the values for all the tested samples in a small way, but the values remained in their clinically acceptable range for all of the crowns.

The goal of our study is to launch magnetic force-driven orthodontics. This continuous study investigated the influence of magnet position on tipping and bodily tooth movement, using 3D printing technology and digital analysis. Orthodontic typodont models (TMs) for space-closure were 3D printed to mimic maxillary central incisors. Nd-Fe-B magnets were placed in the middle third (Model-M), and the cervical third (Model-C), of the tooth. TMs, before and after movement, were digitally scanned and superimposed. The 3D digital coordinates (X, Y, and Z axes), and rotations (yaw, pitch, and roll) of the tooth crown and root, were calculated and compared between the two magnet position settings. Model-M showed higher rates of movement, but more rotation than Model-C (p &lt, 0.01). The root apex of Model-M moved in the opposite direction of the crown (R = &minus, 0.29), indicating tipping movement. In contrast, the crown and root apex moved in the same direction (R = 0.56) in Model-C, indicating bodily movement. These patterns were confirmed in a typodont model of a moderate crowding case. The results validated that modifying the magnet position increased the amount of bodily tooth movement, and decreased rotation/tipping in an ex vivo setting.

Improving the accuracy of the digital model is essential for the digitalization of the dental field. This study introduced a novel method of objective accuracy evaluation of digitized full dental arch model using coordinate measuring machine (CMM). To obtain a true linear measurement value using the CMM, 17 reference balls were attached to the typodont, and 12 measurements between balls on the X-(width), Y-(length), and Z-axes (height) were performed automatically. A rubber impression and a plaster cast replica of the typodont with balls were fabricated, and they were digitized with following methods: (a) true model intraoral scans, (b) impression cone-beam computed tomography (CBCT) scans, (c) cast CBCT scans, and (d) cast extraoral scans. Each scanning method was performed 20 times. Twelve linear measurements on the digitized models were automatically made using software. The one-sample t-test and one-way analysis of variance were used for measurement accuracy analysis. The cast extraoral scan was most accurate on X- and Y-axes, while impression CBCT was the most accurate on Z-axis. Over all axes, the intraoral scan resulted in the most deviation from the true model, and the reproducibility of each scan was also low. Extraoral scan shows high precision on width and length, and impression CBCT is advantageous for dental work where height factor is of importance.

The purpose of this study was to evaluate the accuracy of dental three-dimensional (3D) scanners according to the types of teeth. A computer-aided design (CAD) reference model (CRM) was obtained by scanning the reference typodont model using a high-precision industrial scanner (Solutionix C500, MEDIT). In addition, a CAD test model (CTM) was obtained using seven types of dental 3D scanners (desktop scanners (E1 and DOF Freedom HD) and intraoral scanners (CS3500, CS3600, Trios2, Trios3, and i500)). The 3D inspection software (Geomagic control X, 3DSystems) was used to segment the CRM according to the types of teeth and to superimpose the CTM based on the segmented teeth. The 3D accuracy of the scanner was then analyzed according to the types of teeth. One-way analysis of variance (ANOVA) was used to compare the differences according to the types of teeth in statistical analysis, and the Tukey HSD test was used for post hoc testing (&alpha, = 0.05). Both desktop and intraoral scanners showed significant differences in accuracy according to the types of teeth (P &lt, 0.001), and the accuracy of intraoral scanners tended to get worse from anterior to posterior. Therefore, when scanning a complete arch using an intraoral scanner, the clinician should consider the tendency for the accuracy to decrease from anterior to posterior.

Aims and Objectives: The purpose of this study is to compare digital and conventional impression methods by preclinical students in terms of time and ease and to evaluate their preferences and future expectations. Materials and Methods: Twenty volunteered, 2nd year preclinical students (11 females and 9 males) participated in this study. Students took digital and conventional impressions of the left lower first molar which was made full ceramic crown preparation and opposite full arch from a typodont model (Frasaco, Frasaco GmbH, Tettnang, Germany). They used intraoral scanner (CEREC Omnicam, Sirona Dental GmbH, Bensheim, Germany) for digital impression and also used additional type (Express XT Penta H, 3M ESPE, Seefeld, Germany) and condensation type (Zetaplus, Zhermack SpA, Badia Polesine, Italy) silicones for conventional impression. Their taking impression time was measured. Before taking impression and after taking impression, two kinds of questionnaires were conducted to students about their preference, ease of impression methods, and their future expectations. Statistical analysis was performed by IBM SPSS 23 and Excel 2010 version. Differences between conventional and digital impression in terms of time were analyzed by student’s-t paired test and effect of gender was analyzed by students’s-t independent test. Results: There were statistically significant differences between digital and conventional impression methods in terms of taking impression and total impression time (P < 0.001). But there wasn’t any statistically significant difference between two methods in terms of preparation time. About 85% of students preferred the digital impression method and also 85% of students found that the digital impression method was easy. 95% of students expected to find intraoral scanner in the clinic where working first time. Conclusions: As a result of this study, it has been seen that the students preferred the digital impression method to the conventional impression method and found that the digital impression method was easier.

Purpose: To evaluate the influence of fabrication method and finish line design on marginal and internal fit of full-coverage interim restorations. Methods: Four typodont models of maxillary central-incisor were prepared for full-coverage restorations. Four groups were defined; knife-edge (KE), chamfer (C), rounded-shoulder (RS), rounded-shoulder with bevel (RSB). All preparations were digitally scanned. A total of 80 restorations were fabricated; 20 per group (SLA/3D-printed n = 10, milled n = 10). All restorations were positioned on the master die and scanned using micro-computed tomography. The mean gaps were measured digitally (ImageJ). The results were compared using MANOVA (α =.05). Results: Internal and marginal gaps were significantly influenced by fabrication method (P =.000) and finish-line design (P =.000). 3D-Printed restorations showed statistically significant lower mean gap compared to milled restorations at all points (P =.000). The mean internal gap for 3D-printed restorations were 66, 149, 130, 95 μm and for milled restorations were 89, 177, 185, 154 μm for KE, C, RS, RSB respectively. The mean absolute marginal discrepancy in 3D-printed restorations were (30, 41, 30, 28 μm) and in milled restorations were (56, 54, 52, 38 μm) for KE, C, RS, RSB respectively. Conclusions: The fabrication methods showed more of an influence on the fit compared to the effect of the finish-line design in both milled and printed restorations. SLA-printed interim restorations exhibit lower marginal and internal gap than milled restorations. Nonetheless, for both techniques, all values were within the reported values for CAD/CAM restorations. Significance: 3D-printing can offer an alternative fabrication method comparable to those of milled restorations.

PURPOSE This in vitro study aimed to analyze and compare the reproducibility of zirconia and lithium disilicate crowns manufactured by digital workflow. MATERIALS AND METHODS A typodont model with a prepped upper first molar was set in a phantom head, and a digital impression was obtained with a video intraoral scanner (CEREC Omnicam; Sirona GmbH), from which a single crown was designed and manufactured with CAD/CAM into a zirconia crown and lithium disilicate crown (n=12). Reproducibility of each crown was quantitatively retrieved by superimposing the digitized data of the crown in 3D inspection software, and differences were graphically mapped in color. Areas with large differences were analyzed with digital microscopy. Mean quadratic deviations (RMS) quantitatively obtained from each ceramic group were statistically analyzed with Student's t-test (α=.05). RESULTS The RMS value of lithium disilicate crown was 29.2 (4.1) µm and 17.6 (5.5) µm on the outer and inner surfaces, respectively, whereas these values were 18.6 (2.0) µm and 20.6 (5.1) µm for the zirconia crown. Reproducibility of zirconia and lithium disilicate crowns had a statistically significant difference only on the outer surface (P

With the introduction of rare earth magnets like neodymium-iron-boron (NdFeB), it has become possible to produce small magnets with high forces, necessary for its usage in the field of dentistry, such as for orthodontic tooth movement. The ultimate goal of this project is to establish magnetic force-driven orthodontic treatment as a future treatment modality for comprehensive orthodontic treatment. In order to utilize magnets for orthodontic treatment, we must first understand the characteristics of tooth movement created by magnetic forces. In this study, we aimed to digitally assess the efficacy of magnetic attraction and repulsion forces by means of a 3D digital analysis of movement (distance, direction, angulation and duration) and rotation (yaw, pitch and roll) of the crown and root of teeth in an ex vivo typodont model. We performed space closure and space gain treatment of maxillary central incisors (n = 30) and analyzed the movement and rotation of the teeth and root apex with 3D digital analysis. The results of the typodont model indicated significant differences on amount, speed and rotation of tooth and root movement created by magnetic attraction and repulsion forces. We also mimicked a moderate crowding typodont case and successfully treated it with a combination of attraction and repulsion magnetic forces. The moderate crowding case utilized magnets and a titanium archwire to guide the planned tooth movements and prevent undesired or unexpected movement. Further ex vivo experiments and considerations for biosafety will be necessary to investigate magnet force-driven orthodontics as a future modality of orthodontic treatment., Dentistry; Dental materials; Medical imaging; Health technology;Magnetic forces; NdFeB magnets; Orthodontic tooth movements; Force control

Limited evidence is available comparing the differences between pre-operative and post-operative 3D implant positions from the viewpoint of prosthetics. We aimed to investigate the differences between preplanned positions of virtual provisional restorations and their actual positions following fully guided single-implant placement. Ten maxillary typodonts with missing right central incisors were imaged using cone-beam computed tomography, and digital impressions were obtained using an intraoral scanner. These data were imported into implant-planning software, following which the provisional restorations were designed. After data superimposition, an appropriate implant position was determined, and a computer-assisted implant surgical guide was designed for each typodont. Orders generated from the implant-planning software were imported into relevant computer-aided design software to design the custom abutments. The abutments, provisional restorations, and surgical guides were fabricated, and each restoration was cemented to the corresponding abutments, generating a screw-type immediate provisional restoration. The implants were placed using the surgical guides, and the screw-type provisional restorations were engaged to the implants. The typodonts were then rescanned using the intraoral scanner. The restorations designed at the treatment planning stage were compared with those in the post-operative scan using metrology software. The angular deviation around the central axis of the implant was measured, and the differences in the crown position were converted to root mean square (RMS) values. The post-operative provisional restorations exhibited an absolute angular deviation of 6.94 &plusmn, 5.78&deg, and an RMS value of 85.8 &plusmn, 20.2 &micro, m when compared with their positions in the pre-operative stage. Within the limitations of the present in vitro study, the results highlight the potential application of customized prefabricated immediate provisional restorations after single-implant placement.

BACKGROUND The Bologna reform resulted in a drastic restructuring of pre-clinical training courses at the University of Zurich. The aim of this study was to assess student pre-clinical scaling/root planning skills after just 8.5 hours of manual training. MATERIAL AND METHODS Three consecutive classes of dental students (n = 41; n = 34; n = 48) were tasked with removing lacquer concrement from the maxillary left canine on a typodont using Gracey and universal (Deppeler M23A) curettes. At baseline (prior to instruction), a timed five-minute session of scaling/root planning was undertaken. The second scaling/root planning session was held immediately following training. Eight experienced dental hygienists and eight lay people served as positive and negative controls, using the same instruments and time limit, respectively. Instrumented teeth were collected, scanned and planimetrically analysed for the percentage of tooth surface cleaned. Statistical analyses were performed to assess the dental students' improvement after the training (Wilcoxon signed-rank test) and to compare it to that of laypeople and dental hygienists (Kruskal-Wallis rank sum test followed by Conover's post hoc test). RESULTS At baseline, the dental students' mean scaling scores of the cleaned surfaces were not significantly different than those of laypeople (29.8%, 31.0%, 42% vs 27.9%). However, after 8.5 hours of manual training, the students' ability to clean the maxillary tooth improved significantly and they achieved mean removal values of 61.7%, 79.5% and 76% compared to the 67.4% (P

Objective: We evaluated the effects of tooth displacement on frictional force when conventional ligating lingual brackets (CL-LBs), CL-LBs with a narrow bracket width, and self-ligating lingual brackets (SL-LBs) were used with initial leveling and alignment wires. Methods: CL-LBs (7th Generation), CLLBs with a narrow bracket width (STb), and SL-LBs (In-Ovation L) were tested under three tooth displacement conditions: no displacement (control); a 2-mm palatal displacement (PD) of the maxillary right lateral incisor (MXLI); and a 2-mm gingival displacement (GD) of the maxillary right canine (MXC) (nine groups, n = 7 per group). A stereolithographic typodont system and artificial saliva were used. Static and kinetic frictional forces (SFF and KFF, respectively) were measured while drawing a 0.013-inch copper-nickel-titanium archwire through brackets at 0.5 mm/min for 5 minutes at 36.5 o C. Results: The In-Ovation L exhibited lower SFF under control conditions and lower KFF under all displacement conditions than the 7th Generation and STb (all p < 0.001). No significant difference in SFF existed between the In-Ovation L and STb for a 2-mm GD of the MXC and 2-mm PD of the MXLI. A 2-mm GD of the MXC produced higher SFF and KFF than a 2-mm PD of the MXLI in all brackets (all p < 0.001). Conclusions: CLLBs with narrow bracket widths exhibited higher KFF than SL-LBs under tooth displacement conditions. CL-LBs and ligation methods should be developed to produce SFF and KFF as low as those in SL-LBs during the initial and leveling stage. [Korean J Orthod 2016;46(2):87-95]

The objective of this study was to demonstrate the feasibility of using micro-CT scan of dental impressions for fabricating dental restorations and to compare the dimensional accuracy of dental models generated from various methods. The key idea of the proposed protocol is that dental impression of patients can be accurately digitized by micro-CT scan and that one can make digital cast model from micro-CT data directly. As air regions of the micro-CT scan data of dental impression are equivalent to the real teeth and surrounding structures, one can segment the air regions and fabricate digital cast model in the STL format out of them. The proposed method was validated by a phantom study using a typodont with prepared teeth. Actual measurement and deviation map analysis were performed after acquiring digital cast models for each restoration methods. Comparisons of the milled restorations were also performed by placing them on the prepared teeth of typodont. The results demonstrated that an efficient fabrication of precise dental restoration is achievable by use of the proposed method.

Background The authors conducted a study to compare the effectiveness of two dry-field isolation techniques with that of a control technique (no isolation) in reducing spatter from a dental operative site. Methods The authors designed a benchtop experiment to evaluate spatter patterns after performing simulated occlusal surface preparations on three typodont teeth in a dental manikin. Fluorescein dye served as the marker to enable visualization of the spatter distribution. The authors compared the effectiveness of a nonisolated control consisting of high-volume evacuation (HVE) alone with that of two dry-field isolation techniques: a dental dam with HVE and the Isolite system (Isolite Systems, Santa Barbara, Calif). Results The authors performed a two-way analysis of variance. Both the Isolite device and the dental dam with HVE exhibited a significant decrease in the number of contaminated squares (P < .001) compared with that for the nonisolated control. In addition, overall, the results showed no statistically significant difference between the Isolite system and the dental dam with HVE (P = .126). Conclusions The study results showed that use of a dental dam with HVE or the Isolite system significantly reduced spatter overall compared with use of HVE alone. Clinical Implications Isolation with a dental dam and HVE or with the Isolite system appears to aid in the reduction of spatter during operative dental procedures, potentially reducing exposure to oral pathogens.

Introduction: Comparing ante-mortem and post-mortem dental data is a principal method of identification in forensic odontology. Radiographic images of amalgam have been used in dental forensics for identification due to their unique appearance. Aim: The aim of this study was to investigate whether radio-opaque composite restorations have a potential for identification in forensic odontology. Materials and Methods: Thirty typodont mandibular first molar teeth were prepared with Class-II (proximo-occlusal) cavities and restored with a radio-opaque composite (Tetric N-Ceram). Two sets of standardized radiographs were taken from the 30 teeth, keeping the radiological parameters constant. One set of these 30 radiographs was named as SET 1. Ten randomly chosen radiographs from the other set and two other radiographs of Class-II composite restorations in typodont teeth constituted SET 2. Thirty dentally trained examiners were asked to match the 12 radiographic images of SET 2 with those of SET 1. Results: The results show that 15 examiners were able to correctly match all the 12 images. Statistical analysis was done using kappa statistical test. Conclusion: This study shows that, if the post-mortem radiographs are accurate duplicates of ante-mortem radiographs of composite restorations, then the shape of the composite restoration is unique and can be used for identification.

Background Evaluation of the marginal fit of cemented zirconia copings manufactured after digital impression with Lava™ Chairside Oral Scanner in comparison to that of zirconia copings manufactured after conventional impressions with polyvinyl siloxane. Methods A prepared typodont tooth #36, was replicated 40 times with a vinyl silicone and precise model resin. The dies were randomly divided into two groups according to the impression taking technique. Digital impressions with Lava™ C.O.S. and conventional impressions were taken according to the group. Subsequently zirconia copings were manufactured and cemented on their respective dies with zinc oxide phosphate cement. After embedding in resin, mesio-distal section of each coping was performed with a diamond saw in order to obtain two slices. One half of the specimen was used for evaluation with an optical microscope (OM) and the other half for evaluation with a scanning electron microscope (SEM). Marginal gap (MG) and absolute marginal discrepancy (AMD) were measured mesial and distal on each slice. Results No significant difference of the marginal parameters between the digital and the conventional group was found. The mean values for MG in the digital group were 96.28 μm (+/−43.21 μm) measured with the OM and 99.26 μm (+/−48.73 μm) measured with the SEM, respectively. AMD mean values were 191.54 μm (+/−85.42 μm) measured with the optical microscope and 211.6 μm (+/−96.55 μm) with the SEM. For the conventional group the mean MG values were 94.84 μm (+/−50.77 μm) measured with the OM and 83.37 μm (+/−44.38 μm) measured with the SEM, respectively. AMD mean values were 158.60 μm (+/−69.14 μm) for the OM and 152.72 μm (+/−72.36) for the SEM. Conclusions Copings manufactured after digital impression with Lava™ C.O.S. show comparable marginal parameters with the copings manufactured after conventional impression with polyvinyl syloxane. The mean MG values of both groups fit in the clinically acceptable range. Electronic supplementary material The online version of this article (doi:10.1186/s12903-016-0323-8) contains supplementary material, which is available to authorized users.