Search

Antegrade or retrograde intramedullary nailing is a common and well established procedure for the treatment of femoral shaft fractures. One drawback of this technique is the high incidence of clinically relevant malalignment. Despite intra-operative and radiological improvements this problem has not yet been solved efficiently. The aim of this study was the evaluation of the mechanical influence on the antetorsion angle of intramedullary nails during and after interlocking in femoral shaft fractures.A mechanical instrument was developed allowing a defined torque to be administered to the distal femur fragment. As an optical measurement system for the assessment of the antetorsion angle, a navigation system was applied. Initially the influence of the interlocking mechanism of the nail on the antetorsion deviation was investigated. The distal interlocking hole was fixed free handed or by using a navigation system. The multidirectional movement of the distal femur fragment was documented. Furthermore, the influence of the rotational stability on the antetorsion angle after mechanical stress of 4 NM was investigated by measuring the remaining rotational capacity of the distal femur fragment.The average remaining rotational capacity of the distal femur fragment was 5.8 degrees after locking the nail by hand. The navigated locking resulted in a deviation of only 2 degrees , a significant difference compared to the free-hand procedure. The rotational stability under stress showed an average of 15.4 degrees deviation of the distal fragment. Even after complete interlocking of the intramedullary nail a 14.2 degrees rotational deviation was observed.It could be shown that mechanical stability as well as the interlocking itself of femoral nails have a relevant impact on the antetorsional angle of the femur. Potential sources of error of the femoral antetorsion angle can be caused by the interlocking process as well as by forced rotation of the femur after interlocking. Clinical studies are needed to improve our findings, while the observed effects might have an essential influence on the incidence of femoral malalignment after osteosynthesis by intramedullary nailing of the femur.

Up to now, the use of navigation systems for the placement of scaphoid screws has been impossible, mainly because there have been no ways of fixing the reference markers. Faulty placement rates in internal fixation of the scaphoid show there is a current need for a 3D image-based navigation system and intraoperative monitoring of how successful the procedure will be. For this reason, we have developed a new radiotransparent hand fixation device (Scaph-Splint), which allows reliable and accurate drilling of the scaphoid using 3D navigation. Tests of this device and the simultaneous precise placement of screws securing an internal fixation device are described in this paper.Relative movements between the wrist and fixation device were measured with a 3-D ultrasound motion analyser system. Five cadaveric upper extremity specimens were then used for further navigated test applications. Each specimen was placed in the fixation device, and both the forearm and hand were secured to the two surfaces, with the wrist in approximately 80 degrees of extension. A reference marker was then securely fixed to the fixation device. A commercial navigation system and 3-D fluoroscopic imaging were used for each trial. Under navigation, the scaphoid was drilled in retrograde fashion, and a screw was placed into the drilled hole. Following screw placement, a 3D scan was performed to evaluate its position. The screw placement was analysed blindly to optimal placement and drill or screw perforation, and the image quality was rated on a visual analog scale (VAS).There were few artefacts, and the image quality of the 3-D scan was judged as as good (VAS 79). Deviations ofor=0.2 mm between planned trajectory and drilling tunnal were not found in any of the specimens; there were deviations ofor=1 mm in one case, and all other cases showed deviations ofor=1 mm. There were no registration failures of the navigation system, indicating that no loosening of the reference marker or movement of the hand occurred. There was one case of scaphoid perforation at the distal pole.We found that the Scaph-Split allowed complete immobilisation of the hand and carpus. This allowed for adequate reference tracker stability and subsequent successful 3D navigated fluoroscopic drilling and screw placement in the scaphoid. While further tests on fresh-frozen cadavers is warranted, this technique may prove clinically to be very useful for surgeons treating scaphoid fractures.