Search

The construction industry had approached a critical limit which led to the increase of cement production. The production of cement would cause a broader environmental implication. Cement production is a major source of carbon dioxide emission. Carbon dioxide gas contributes about 63.33% of global warming since the production of one ton of cement would emit about one ton of carbon dioxide to the environment. To mitigate this issue, the research community has investigated the use of waste materials that possess similar chemical properties with cement content as a material for partial cement replacement. The use of rice husk ash has shown to be a contending candidate in the literature. Therefore, this paper attempts at reviewing the performance of rice husk ash as partial cement replacement. It could be observed from the literature that concrete with 5% up to 15% of rice husk ash showed an equivalent performance to ordinary concrete in compressive, flexural, and tensile strength. Thus, rice husk ash can be used as a material replacement in concrete and reduces pollution that originates from cement production and open burning of rice husk.

Construction sludge frequently has high alkalinity after its generation or during the intermediate treatment process. The aim of this study is to experimentally investigate the potential of combining accelerated carbonation and a paper sludge ash-based stabilizer (PSAS) to neutralize the alkalinity of construction sludge in a short period and to improve its strength for use as a recycled material. The experimental results indicate that the addition of a PSAS significantly granulated the alkaline sludge, and once granulated, the PSAS successfully accelerated the pH neutralization of the alkaline sludge. It was also found that the decrease in dry density ρd and the degree of saturation Sr of the PSAS-treated sludge was able to reduce the period required for the pH neutralization, tN. The decrease in ρd is thought to allow fresh CO2 gas to penetrate the specimen more easily. However, if Sr is below a certain limit, it does not strongly facilitate the reduction of tN. This implies that pH neutralization cannot be accelerated when the amount of water in the sludge is below a certain level. Moreover, it was found that mean particle diameter D50 also affected tN. The strength development of the PSAS-treated sludge was evaluated using a series of cone index tests. It was found that the strength of the alkaline sludge without the PSAS was significantly decreased by accelerated carbonation, but was significantly increased even after accelerated carbonation when the PSAS was present. Due to the porosities of the remaining PS ash particles, most of the contribution of the water absorption and retention performance of the PSAS to the strength development of the PSAS-treated sludge was secured after accelerated carbonation. In addition, the granulated particles of the PSAS-treated sludge retained their granular shape to some extent. Therefore, it is presumed that the friction and interlocking of the particles did not decrease significantly. It was also found that, after carbonation, the qc of the PSAS-treated sludge increased more rapidly than that of the alkaline sludge without the PSAS. A further detailed examination of the test results showed that under air-curing conditions, the qc of the treated sludge with accelerated carbonation increased relatively gradually compared to that of the treated sludge without accelerated carbonation.

Controlling the size and rigidity of calcium carbonate became possible. HCCs were developed and manufactured by the in situ reaction of carbon dioxide and calcium oxide, which were already preflocculated together with GCC using ionic polymers before the reaction. HCC is deformable under pressure during the papermaking process, and its degree of rigidity can be controlled by adjusting the fraction of calcium oxide. The size of HCC can be further controlled by adjusting shearing force. The more the fraction of calcium oxide, the more rigid the HCC and the smaller the diameter of the HCC. When used in papermaking, HCC increased the tensile strength and bulk of paper simultaneously without lowering other essential paper properties, and its deformable nature under pressure improved paper smoothness. Saving chemical pulp by 10% by replacing it with HCC, which is 3–4 times less expensive than the chemical pulp, was demonstrated successfully without lowering the essential properties of paper. Implementation of HCC in the paper mill may result in saving chemical pulp, drying energy, and production cost. The paper mill may utilize the carbon dioxide from the mill stack after purification for HCC preparation.

The conversion of CO2 into useful chemicals can lead to the production of carbon neutral fuels and reduce greenhouse gas emissions. A key technological challenge necessary to enable such a process is the development of substrates that are active, cost effective, and selective for this reaction. In this regard, the reduction of CO2 via electrochemical means is one of the most attractive alternatives but still requires rather unique electrodes. Considering the potential of this approach, this report describes a one-step methodology for the synthesis of carbon electrodes derived from simple paper and modified with various metallic nanoparticles. Upon a preliminary selection based on the catalytic activity towards CO2 reduction, the electrodes containing CuNPs were further characterized by Raman spectroscopy, and electrical/electrochemical techniques. These electrodes were then applied for the electrochemical reduction of CO2, leading to the formation of compounds with one carbon atom (formic acid), two carbon atoms (ethenone), three carbon atoms (propanoic acid) and four carbon atoms (butanol and butanoic acid). Fil: Gomez, Federico Jose Vicente. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Mendoza. Instituto de Biología Agrícola de Mendoza. Universidad Nacional de Cuyo. Facultad de Ciencias Agrarias. Instituto de Biología Agrícola de Mendoza; Argentina Fil: Chumanov, George. Clemson University; Estados Unidos Fil: Silva, María Fernanda. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Mendoza. Instituto de Biología Agrícola de Mendoza. Universidad Nacional de Cuyo. Facultad de Ciencias Agrarias. Instituto de Biología Agrícola de Mendoza; Argentina. Clemson University; Estados Unidos Fil: Garcia, Carlos D.. Clemson University; Estados Unidos

In papermaking, pre-flocculation of fillers such as ground calcium carbonate (GCC) improves the tensile strength of paper sheets. However, the pre-flocculated fillers mostly suffer from the instability of the floc shape such as the decrease in floc diameter with time elapse after preparation and no improvement of bulk and stiffness. The addition of calcium compounds such as calcium oxide or calcium hydroxide to the pre-flocculated GCC, and injection with carbon dioxide caused pre-flocculated GCC flocs to be covered with newly formed calcium carbonate. This product, called post hybrid calcium carbonate (pHCC), was found to be more stable in size and gave better sheet strength than the pre-flocculated ones. Furthermore, pHCC gave remarkably higher bulk and stiffness than the pre-flocculated flocs did without impairing smoothness that was essential in printing paper. The proper use of pHCC in papermaking could allow the production of high loaded paper with more than 10% higher filler contents, which could reduce paper production cost and save drying energy. The proportion of the newly formed calcium carbonate in pHCC, turbulence intensity at preparation stage, and the effect of storage time were investigated.

Here in this study, co-pyrolysis of paper mill sludge (PMS) and spent coffee ground (SCG) was conducted to mainly recover energy and additionally produce engineered biochar as an adsorbent. More specifically, to enhance the generation of syngas (H 2 and CO) through co-pyrolysis of PMS and SCG and modify the physico-chemical properties of biochar, carbon dioxide (CO 2 ) was used as reaction medium. The CO 2 co-feeding impact on co-pyrolysis with various mass ratios of PMS and SCG was also evaluated to explore any catalytic effects arising from CO 2 and Fe/Ca species in PMS. The decrease in pyrolytic oil substances was apparent due to the synergistic effects of CO 2 and Fe/Ca species. Moreover, the generation of CO was catalytically enhanced in the presence of Fe/Ca species in PMS. Co-pyrolysis in CO 2 not only converted the impregnated Fe ions into magnetite (Fe 3 O 4 ), but also created porous biochar. One biochar fabricated at the optimal mass ratio (PMS:SCG = 7:3) exhibited the highest adsorption capability toward As(V) due to adequate balancing between the amount of Fe/Ca solid minerals and biochar porosity. As a result, co-pyrolysis using CO 2 as reaction medium can be a feasible option for the generation of CO along with production of biochar as a byproduct which can be used in environmental application.

Utilization of the quality-upgraded waste paper in the manufacture of paper and board will reduce the wood consumption and pulping energy. While the optical property of the fibers from recycled old newspaper is very poor, in-situ calcium carbonate formation on those fibers by injecting carbon dioxide to the mixed slurry of those pulp and calcium oxide improved their brightness. Upgrading recycled old newspaper to substitute more expensive wood furnish, such as recycled old magazine, was successfully demonstrated in the present study. This study showed that the in-situ calcium carbonate formation process improved the optical quality of the recycled old newspaper by covering colored impurities with newly formed calcium carbonate, and improved calcium carbonate retention in papermaking process by attaching them to fibers. The strength reduction by the presence of newly formed calcium carbonate in the paper was recovered by adding strength agent. High ash retention at high ash content under the strong turbulence in the modern paper mill was achieved by the application of the in-situ calcium carbonate formation method. The quality-upgrade of recycled fibers and cost saving in the manufacture of duplex paperboard were demonstrated in the mill trial.

A Carbon dioxide (CO2) emission from the boiler is one of the primary sources of greenhouse gas (GHG) which must be reduced. Nowadays, the boiler emissions discharged into the atmosphere has not been utilized yet. An experiment of Spirulina platensis cultivation in laboratory scale with the addition of CO2 flue gas of coal-fired boilers has been done. CO2 flue gas with a flow rate of 0.25-0.75 L/min was added into paper mill effluent as the growth medium of Spirulina platensis. The biomass growing of Spirulina platensis, pH of medium and CO2 captured during the experiment were observed. The result indicated that CO2 flue gas of coal-fired boilers of the paper mill could be utilized for cultivating of Spirulina platensis. The biomass productivity of Spirulina platensis in the amount of 220 mg/L.day or 39 g/m2.day could be obtained with the addition of CO2 flue gas in the flow rate of 0.75 L/min. Spirulina platensis contains protein, fat, fiber, ash and amino acids. It also contains sodium, calcium and magnesium. But it has no cadmium content. It is potentially be used as animal dietary supplements. CO2 flue gas from the boiler emission can be used for cultivation of Spirulina platensis and contribute in reducing of CO2 gas boiler emissions like greenhouse gases (GHG) by 0.20% of total CO2 added.

Paper waste sludge (PWS) is the main and the greatest by-product in paper production process, and its elimination as well as destruction is a primary environmental problem. This research explores the feasibility of such wastes to be used in polyurethane foam composites. It is well known that using water as a sole blowing agent has major drawbacks such as long demould time, shrinkage, high diffusion rate of carbon dioxide and etc.; therefore, the bio-based propylene glycol (RPG) is used in order to solve such problems. The addition of 20 parts by weight (pbw) of RPG eliminates the primary shrinkage of the foam composites when PWS is used in the amount varying from 5% to 20%, and improves the dimensional stability at 70 oC and 90% relative humidity conditions. The addition of titanate coupling agent modified PWS particles increases the compressive strength of the final composites from ̴ 26% to ̴ 53%, from ̴ 17% to ̴ 31% and from ̴ 3% to ̴ 23% for, respectively, 10 pbw, 15 pbw and 20 pbw RPG extended foam composites.

Pyrolysis of paper mill sludge (PMS) was conducted to produce syngas (H 2 and CO) and fabricate magnetic biochar (PMS biochar) for use as an adsorbent for As(V). The enhanced generation of CO was observed in the CO 2 atmosphere due to reactions triggered by CO 2 . Particularly, the generation of syngas from pyrolysis of PMS in CO 2 (9.6 mol% at 720 °C) was superior to the cases of pyrolysis of acid-washed PMS ( i.e. , minerals-eliminated PMS) in CO 2 (2.9 mol% at 720 °C), which evidences catalytic effects attributed by Fe and Ca species contained in PMS. Based on the results of X-ray diffraction (XRD), pyrolysis of PMS in CO 2 led to the conversion of Fe species into magnetite (Fe 3 O 4 ) solid phase that imparted the magnetic property to the biochar (saturation magnetization: 28.4 emu g −1 ). The PMS biochar exhibited high As(V) adsorption capacity of 34.1 mg g −1 in a given condition, which could be attributed to the great adsorption affinity of Fe 3 O 4 /CaCO 3 mixture toward As(V). The integrated approach for the utilization of PMS could satisfy growing demand for renewable energy and environmental sustainability.

The CO2 concentration in the atmosphere is increasing and threatening the earth's climate. Selective CO2 capture at large point sources will help to reduce the CO2 emissions to the atmosphere. Biochar with microporous structure could be a potential material to capture CO2. The impact of feedstock type, pyrolysis temperature and steam activation of biochars were evaluated for CO2 adsorption capacity. Pine sawdust biochars were produced at 550 °C, and steam activated for 45 min at the same temperature after completing the pyrolysis (PS550 and PSS550). Paper mill sludge biochars were produced at 300 and 600 °C (PMS300 and PMS600). The CO2 adsorption capacity of biochars was tested at 25 °C using a volumetric sorption analyzer. Pine sawdust biochars showed significantly higher CO2 adsorption capacity than paper mill sludge biochars due to high surface area and microporosity. Pine sawdust biochars were then evaluated for dynamic adsorption under representative post-combustion flue gas concentration conditions (15% CO2, 85% N2) using a breakthrough rig. Both materials showed selective CO2 uptake over N2 which is the major component along with CO2 in flue gas. PSS550 had slightly higher CO2 adsorption capacity (0.73 mmol g^-1 vs 0.67 mmol g^-1) and CO2 over N2 selectivity (26 vs 18) than PS550 possibly due to increase of microporosity, surface area, and oxygen containing basic functional groups through steam activation. Pine sawdust biochar is an environmentally friendly and low-cost material to capture CO2.

The 2011 White Paper on Transport of the European Commission spells out a series of targets for 2030 and 2050. One of the 10 targets is explicitly related to urban transport and stipulates: “Halve the use of ‘conventionally fuelled’ cars in urban transport by 2030; phase them out in cities by 2050. Achieve essentially CO2-free city logistics in major urban centres by 2030.” With this paper we present and discuss a roadmap that deals with the question who needs to do what by when in order to reach the White Paper goal for urban transport. The “stakeholder-driven” roadmap was developed in the FP7 project TRANSFORuM. The paper will present the key findings and the suggested action steps identified in the roadmap. The paper will also exemplify three possible urban transformation pathways towards the urban target. This approach emerged from stakeholder consultations which highlighted the need to take into account the widely differing conditions among European cities.

Large areas of mine tailings are reclaimed by applying organic amendments such as paper mill sludge (PMS). Although mining industries can use PMS freshly generated by paper mills, operational constraints on paper industries make temporary landfilling of this material an unavoidable alternative for the paper industries, creating the most prominent PMS source for mining industries. This study aimed to quantify soil greenhouse gas (GHG) emissions (N2O, CO2, and CH4) after application of landfilled PMS (LPMS; i.e., excavated from a landfill site at a paper mill) and LPMS combined with a seeding treatment of white clover (Trifolium repens L.) on nonacidic mine tailings site prior to reforestation. Soil N2O, CO2, and CH4 fluxes were measured after applications of 50 and 100 Mg dry LPMS ha−1 during two consecutive snowfree seasons on two adjacent sites; LPMS was applied once in the first season. The LPMS application increased N2O emissions (7.6 to 34.7 kg N2O-N ha−1, comprising 1.04 to 2.43% of applied N) compared with the unamended control during the first season; these emissions were negligible during the second season. The LPMS application increased CO2 emissions (~5800 to 11,400 kg CO2–C ha−1, comprising 7 to 27% of applied C) compared with the unamended control on both sites and in both seasons. Fluxes of CH4 were negligible. White clover combined with LPMS treatments did not affect soil GHG emissions. These new GHG emission factors should be integrated into life-cycle analyses to evaluate the C footprint of potential symbioses between the mining and paper industries. Future research should focus on the effect of PMS applications on soil GHG emissions from a variety of mine tailings under various management practices and climatic conditions to plan responsible and sustainable land reclamation.

Composting is considered to be a natural, sustainable, and highly beneficial method for solid waste disposal. The objective of this study was to investigate the two-stage composting of green waste (GW) as affected by the addition of sugar beet pulp (SBP; at 0, 25, and 35%) and/or paper waste (PW; at 0, 5, and 10%) as bulking agents. The combination of SBP and PW greatly improved the composting conditions and the final compost quality in terms of composting temperature; pH; emissions of ammonia, nitrite nitrogen, and carbon dioxide; lignocellulose degradation; microbial abundance; enzyme activities; particle-size distribution; the ratio of water-soluble organic carbon to organic nitrogen; and phytotoxicity. The optimal two-stage composting process of GW and the highest quality compost product were obtained with the combination of 25% SBP and 10% PW. This optimal combination of bulking agents produced a mature and stable final compost product in only 20 days.

Needs for high ash loading in printing paper increase as green house gas (GHG) emission regulation becomes more stricter and pressure of lowering paper production cost increases. To meet the needs, a new type of filler was developed. The mixture of ground calcium carbonate (GCC) and calcium oxide was pre-floccuated with polyelectrolyte and further treated with carbon dioxide to form new calcium carbonate between GCCs. The final products were called as hybrid calcium carbonate (HCC), and its properties were compared to the GCC and the pre-flocculated GCC. Results showed increase in tensile, smoothness, opacity, and bulk for HCC.

Straw pulp in China, which is the world's largest producer of this material, suffers from water and energy shortages during its entire life cycle. However, limited systematic studies have focused on these issues, and decision makers need be provided with improvement methods for the environmental performance. Thus, an impact-oriented energy and carbon coupled water footprint analysis was conducted in this study based on ISO standards. Results showed that the impact of energy consumption and carbon emissions exceeded that of water footprint. Carcinogens, non-carcinogens, and freshwater ecotoxicity also played effective roles in improving the environmental performance. Optimizing key indirect processes, including chemicals production, steam preparation, electricity generation, wood pulping, and fertilizer recovery, dominated the reduction in environmental burdens. Direct freshwater consumption and wastewater disposal played additional effective roles in controlling water footprint. The water network was thus optimized by a water pinch analysis to decrease the freshwater consumption and pollutant emissions by maximum values of 91.5% and 99.7% after optimization, respectively. Meanwhile, carbon dioxide, methane, chromium, arsenic, mercury, titanium, copper, strontium, total nitrogen, total phosphorus, BOD5, and COD were the main pollutants. Overall, the environmental impact can be further reduced by diminishing coal power ratio in national energy structure, adopting recovered steam, and considering multistage regeneration water network to cope with different water use demands.

History has been kind to Christian Bohr (1855–1911). His name is attached eponymously to three different areas of respiratory physiology. The first is the Bohr dead space, which refers to the portion of the tidal volume that does not undergo gas exchange. The second is the increase in oxygen affinity of hemoglobin caused by the addition of carbon dioxide to the blood. This is known as the Bohr effect and is a very important feature of gas exchange, both in the lung and in peripheral tissues. Both of these contributions by Bohr are familiar to most students. Bohr’s third contribution refers to the calculation of the changes in the Po2 of blood as oxygen is loaded in the pulmonary capillary, the so-called Bohr integration. This contribution is less well known now, partly because of the advent of digital computing, but it was important in its day. The analysis is challenging because the very nonlinear shape of the oxygen dissociation curve means that the Po2 difference between the alveolar gas and the capillary blood, which is the driving pressure for diffusion, changes in a complicated way. All three papers are in German, and two of them are long and tedious to read. English translations are available, but few people read the papers, despite the fact that the first two articles are very frequently cited. In the present article, Bohr’s contributions are reviewed, and some parts of the articles that are particularly difficult to understand are clarified.

Based on surface science, adsorption of mineral oil, water, gas products (typified by CO2 and CH4), and acids (typified by formic acid) on meta-aramid insulation paper has been investigated by molecular dynamics simulations. When the adsorption process finishes, the free volume fraction in the crystalline region is very small owing to the stable molecular arrangement of fiber. In addition, the number of pores on the surface of the meta-aramid fiber and the pore size are small, and the stable configuration of hydrogen bonds plays an important role, so it is difficult for the mineral oil and aging products to enter the meta-aramid crystalline region. The irregular arrangement of molecules in the amorphous region means that it is easier for the mineral oil and aging products to enter the amorphous region than the crystalline region, and the influence of these substances on the amorphous region is greater than that on the crystalline region. The order of the adsorption strengths of the four types of aging products on meta-aramid fiber is formic acid > water > CO2 > CH4. Therefore, it is necessary to monitor the acid and water contents in transformers with meta-aramid insulation paper as the solid insulation material.

As China's demand for paper products increases, China's paper industry faces enormous pressure to reduce greenhouse gas emissions. By using material flow analysis in combination with input-output analysis, this study measured the waste paper recovery rate in a more accurate method and analyzed the impact of waste paper recycling on the carbon emissions from China's paper industry. China's waste paper recovery rate estimated in this study was close to 70% in 2017, much higher than that of 48% obtained with the traditional method. The regression results displayed a negative relationship between waste paper recovery rate and CO

In cigarette production, the cellulosic paper essentially derived from flax fibers or other fiber materials is used as the wrapping material. During smoking of cigarettes, the highly toxic carbon monoxide is produced. To decrease the amount of carbon monoxide emission in the mainstream smoke, the engineering of all cigarette components including cellulosic cigarette paper and tobacco column is critical. This review summarizes the concepts related to engineering of cigarette paper. These mainly include permeability control, increased use of burn additives, optimization of fiber basis weight, engineering of calcium carbonate fillers, and incorporation of catalysts/oxidants. In particular, catalytic and/or oxidative conversion of carbon monoxide to carbon dioxide has been very widely reported. The control of permeability/diffusivity of cigarette paper is also of critical importance for enhanced diffusion of carbon monoxide out of the cigarette. The development of new concepts and combination of various concepts may lead to breakthroughs in this area.

The present work introduces the study of the CO2 capture process by zeolites synthesized from paper sludge and scrap glass. Zeolites ZSM-5, analcime and wairakite were produced by means of two types of Structure Directing Agents (SDA): tetrapropilamonium (TPA) and ethanol. On the one hand, zeolite ZSM-5 was synthesized using TPA; on the other hand, analcime and wairakite were produced with ethanol. The temperature programmed desorption (TPD) technique was performed for determining the CO2 sorption capacity of these zeolites at two sorption temperatures: 50 and 100°C. CO2 sorption capacity of zeolite ZSM-5 synthesized at 50°C was 0.683 mmol/g representing 38.2% of the value measured for a zeolite ZSM-5 commercial. Zeolite analcime showed a higher CO2 sorption capacity (1.698 mmol/g) at 50°C and its regeneration temperature was relatively low. Zeolites synthesized in this study can be used in the purification of biogas and this will produce energy without increasing the atmospheric CO2 concentrations.

The adsorption/desorption cycles of the alkaline paper mill waste (APMW) can be used to remove CO 2 from coal-fired power plants. In this work, the prolonged adsorption duration treatment was used to modify CO 2 capture behavior of the raw and the prewashed APMW in the multiple adsorption/desorption cycles. The effects of increased duration of adsorption and CO 2 partial pressure in the first cycle on the fractional adsorption of CO 2 and adsorption rate were investigated, when the raw and the prewashed APMW are employed as the sorbents. The cyclic CO 2 capture behavior of APMW after the repeated prolonged adsorption in different cycles was also studied. For the raw and the prewashed APMW as the sorbents, 9–12 h adsorption of CO 2 just in the 1st cycle enhances the cyclic fractional adsorption of CO 2 and adsorption rate of CO 2 in the 1st cycle and the subsequent cycles. The repeated prolonged adsorptions in the various cycles are more effective to increase the cyclic CO 2 capture capacity of APMW than only in the 1st cycle. The longer adsorption duration results in larger area and volume of pores in 10–100 nm in diameter for CaO derived from APMW after the next cycles, which are helpful to cyclic CO 2 capture of APMW. The raw and the prewashed APMW can retain high CO 2 adsorption reactivity by the prolonged adsorption duration treatment in the multiple adsorption/desorption cycles.

Carbon dioxide, CO2 accounts for most of the emission from all the types of greenhouse gasses in the world. The ability of CO2 to remain longer than other greenhouse gases and the convenience of producing CO2 has resulted in its high projection in a yearly manner. The prime factor for the emission of CO2 are from the actions of human beings. One such human act is the concrete industry. Total emissions from the concrete industry could therefore contribute as much as 8% of global CO2 emissions. Sequestered CO2 in concrete can provide an impact on reducing the carbon footprint and is also able to improve the compressive strength of concrete. During this process, the sequestered carbon dioxide chemically reacts with cement to produce a mineral, trapping carbon dioxide gas in the concrete. Hence, sequestering carbon dioxide gas in concrete does not only on a bigger scale reduces carbon footprint, but it also reduces the impact the construction industry has on the environment. This paper presents a detailed review on the chemical reaction that takes place during the sequestration of carbon dioxide and the research published on the effects of carbon dioxide sequestered concrete on its properties. The impact this process has on the concrete industry and the environment is discussed in this paper.

Climate change is expected to produce shifts in species distributions as well as behavioural and physiological adaptations to find suitable conditions or to cope with the altered environment. The paper wasps Polistes dominula and Polistes gallicus are closely related species, native in the European Mediterranean region and North Africa. P. dominula has expanded its range to the relatively cooler climates of Northern and Eastern Europe, but P. gallicus remained in its original distribution area. In order to reveal their metabolic adaptation to the current climate conditions, and the impact on energy demand at future climate conditions, we investigated the respiratory metabolic rate (CO2 production) of P. dominula from Austria and P. gallicus from Italy. In contrast to the metabolic cold adaptation hypothesis their standard metabolic rate was nearly the same and increased in a typical exponential course with increasing ambient temperature. The metabolic rate of active wasps was higher than the standard metabolic rate and increased with the wasps' activity. There was no obvious difference in the active metabolism between the two species, with the exception that some P. gallicus individuals showed some extraordinary high values. A simultaneous measurement of metabolic rate and body temperature revealed that increased CO2 production was accompanied by endothermic activity. The two investigated populations of paper wasps are quite similar in their metabolic response to temperature, although they live in different climate regions. The spread of P. dominula into cooler regions did not have significant influence on their active and standard metabolic rate.

A colorimetric assay was developed which has the capability of determining urea in biological samples. It is an origami paper-based sensor consisting of silver nanoparticles that were synthesized by using two different capping agents: thiomalic acid and maltol. The function of the assay relied on hydrolysis of urea to ammonia and carbon dioxide in the presence of urease. The products interacted with nanoparticles which caused aggregation. Interestingly, thiomalic acid capped with silver nanoparticles were selective to ammonia, and the other nanoparticles synthesized by maltol responded to carbon dioxide. These interactions turned the color of nanoparticles from yellow to brown and red, respectively. The resulting colorations were captured by a floatable scanner. A routine image analysis software was utilized to provide the response of the assays. The method was applied to individually determine ammonia, carbon dioxide, and urea. The linear range was 0.06 mg.dL−1-170.0 mg.dL−1 for ammonia, 0.08 mg.dL−1-220.0 mg.dL−1 for carbon dioxide, and 0.5 mg.dL−1-200.0 mg.dL−1 for urea. The respective limits of detection were 0.03 mg.dL−1, 0.06 mg.dL−1, and 0.18 mg.dL−1. No interferences were found in the detremination of urea. The method demonstrates a reliable performance for determination of urea in both saliva and blood samples.

Summary This study estimated paper and paperboard demand, pulpwood demand, and carbon dioxide (CO2) emissions from production of paper and paperboard through 2050 in ten Asian countries. Under scenarios of varying population, gross domestic product (GDP), and per capita paper and paperboard demand, we analyzed the relationship between economic growth and consumption of paper and paperboard. We also evaluated options to reduce CO2 emissions through increased use of black liquor, waste paper pulping, and wood chemical pulping, as well as improvements in pulp, paper, and paperboard production technology. The quadratic curve model (inverted U) for per capita consumption of paper and paperboard against per capita GDP resulted in significant regression coefficients and higher adjusted R2 values than linear and logarithmic curve models for all uses of paper and paperboard. The estimated paper and paperboard demand in the ten countries in 2050 ranged from 112% (328%) to 156% (454%) of total 2005 consumption for the world (for the ten Asian countries). Of this estimated paper and paperboard demand, China accounted for about 50% and India 20%. The estimated pulpwood demand in these ten countries in 2050 ranged from 13% (48%) to 21% (84%) of global (ten country) 2005 wood supply potential. The introduction or increase of the use of black liquor, waste paper pulping, the combination of wood chemical pulping and black liquor, and technological improvements produced CO2 reductions of 24%, 5%, 32%, and 25%, respectively, compared to 2050 emission levels in the no-measure (unadjusted) option, assuming sustainable forest management.

This paper describes the precipitated calcium carbonate filler applied to paper industry, which was prepared by adding a specific crystal control agent. And a series of influencing factors in carbonation process was studied, such as carbonization temperature, concentration of milk of lime, carbon dioxide concentration and the crystal shape control dosage. Therefore the optimum conditions for preparation of chrysanthemum-shaped crystalline calcium carbonate were determined.

Greenhouse gas (GHG) emission in wastewater treatment plants of the pulp-and-paper industry was estimated by using a dynamic mathematical model. Significant variations were shown in the magnitude of GHG generation in response to variations in operating parameters, demonstrating the limited capacity of steady-state models in predicting the time-dependent emissions of these harmful gases. The examined treatment systems used aerobic, anaerobic, and hybrid-anaerobic/aerobic-biological processes along with chemical coagulation/flocculation, anaerobic digester, nitrification and denitrification processes, and biogas recovery. The pertinent operating parameters included the influent substrate concentration, influent flow rate, and temperature. Although the average predictions by the dynamic model were only 10 % different from those of steady-state model during 140 days of operation of the examined systems, the daily variations of GHG emissions were different up to ± 30, ± 19, and ± 17 % in the aerobic, anaerobic, and hybrid systems, respectively. The variations of process variables caused fluctuations in energy generation from biogas recovery by ± 6, ± 7, and ± 4 % in the three examined systems, respectively. The lowest variations were observed in the hybrid system, showing the stability of this particular process design.

Paper is one of the oldest and most abundant materials known to man. Recently, there has been a considerable interest in creating paper devices by combining paper with other functional materials. In this letter, we demonstrate a simple fabrication technique to create water-resistant ferro-patterns on wax paper using CO2 laser ablation. A resolution of about 100 mu m is achieved which is mostly limited by the cellulose fiber size (similar to 50 mu m) in the wax paper and can be improved by using a smaller cellulose matrix. Laser ablation results in modification of surface morphology and chemistry, leading to a change in surface energy. We also present a 2D model for ferrofluid deposition relating the size of the pattern to the amount of ferroparticles deposited on the surface. Finally, a paper gripper is presented to demonstrate advantages of our technique, which allows microscale patterning and machining in a single step.

The pulp and paper industry is placed in a unique position as biomass used as feedstock is now in increasingly high demand from the energy sector. Increased demand for biomass increases pressure on the availability of this resource, which might strengthen the need for recycling of paper. In this study, we calculate the energy use and carbon dioxide emissions for paper production from three pulp types. Increased recycling enables an increase in biomass availability and reduces life-cycle energy use and carbon dioxide emissions. Recovered paper as feedstock leads to lowest energy use (22 GJ/t) and CO2 emissions (−1100 kg CO2/t) when biomass not used for paper production is assumed to be converted into bio-energy. Large differences exist between paper grades in e.g. electricity and heat use during production, fibre furnish, filler content and recyclability. We found large variation in energy use over the life-cycle of different grades. However, in all paper grades, life-cycle energy use decreases with increased recycling rates and increased use of recovered fibres. The average life-cycle energy use of the paper mix produced in The Netherlands, where the recycling rate is approximately 75%, is about 14 GJ/t. This equals CO2 savings of about 1 t CO2/t paper if no recycled fibres would be used.

A new method, microwave pyrolysis, has been investigated to dispose the paper mill sludge. Microwave pyrolysis is a new fast pyrolysis technology for biomass. The effects of various different factors on paper mill sludge’s microwave pyrolysis were mainly discussed. The results showed that the mass of the paper mill sludge reduced very rapidly within the first 6 min and then flattened out with the microwave reaction time increasing; The greater the microwave power was, the faster the sludge’s pyrolysis and the more the smell and concentration of diesel smoke was; The pyrolysis performance was better when the dosage of the paper mill sludge was increased and of 5% NaOH was added as microwave absorbers; Under CO2 atmosphere, the pyrolysis performance was the best when of 5% NaOH was added, while under N2 atmosphere, the pyrolysis performance was the best when of 5% ZnCl2 was added.

Bioelectrochemical reactors (BERs) with a cathodic working potential of -0.6 or -0.8 V more efficiently degraded cellulosic material, i.e., filter paper (57.4-74.1% in 3 days and 95.9-96.3% in 7 days) than did control reactors without giving exogenous potential (15.4% in 3 days and 64.2% in 7 days). At the same time, resultant conversions to methane and carbon dioxide in cathodic working chamber of BERs by application of electrochemical reduction in 3 days of operation were larger than control reactors. However, cumulative methane production in cathodic BERs was similar to those in control reactors after 7 days of operation. Microscopic observation and 16S rRNA gene analysis showed that microbial growth in the entire consortium was higher after 2 days of operation of cathodic BERs as compared with the control reactors. In addition, the number of methanogenic 16S rRNA gene copies in cathodic BERs was higher than in control reactors. Moreover, archaeal community structures constructed in cathodic BERs consisted of hydrogenotrophic methanogen-related organisms and differed from those in control reactors after 2 days of operation. Specifically, the amount of Methanothermobacter species in cathodic BERs was higher within archaeal communities than in those control reactors after 2 days of operation. Electrochemical reduction may be effective for accelerating microbial growth in the start-up period and thereby increasing microbial treatment of cellulosic waste and methane production.

Secondary pulp/paper-mill sludge (SPP) and sewage sludges (primary, secondary, and digested sewage sludges) were treated in supercritical water at temperatures ranging between 400 degrees Celsius and 550 degrees Celsius over 20-120 min for energy recovery. Low temperature and short reaction time favored the formation of heavy oil (HO) products, which were mainly composed of a variety of phenol and phenolic compounds, as well as some nitrogen-containing compounds, long-chain alkenes and alcohols, etc., with high gross calorific values (>36 MJ/kg). By contrast, the formation of synthetic gases, a mixture of hydrogen, carbon monoxide, carbon dioxide, methane, and other light hydrocarbons, were not significantly affected by reaction time but greatly enhanced with increasing temperature. The highest gas yield was obtained at 550 degrees Celsius, where 37.7 wt.% of the SPP (on dry basis) was converted into gases, with hydrogen yields as high as 14.5 mol H(2)/kg SPP (on a dry basis). In comparison to sewage sludges, SPP exhibited a greater capability for the production of HO and gases owing to its higher contents of volatiles and alkali metals, indicating a prospective utilization potential for SPP as a source of bio-energy.

The two paper wasps, Polistes dominula and Polistes gallicus, are related species with strongly differing distribution ranges. We investigated thermal tolerance traits (critical thermal limits and metabolic response to temperature) to gain knowledge about physiological adaptations to their local climate conditions and to get evidence for the reasons of P. dominula’s successful dispersion. Body and ambient temperature measurements at the nests revealed behavioural adaptations to microclimate. The species differed clearly in critical thermal minimum (P. dominula −1.4 °C, P. gallicus −0.4 °C), but not significantly in critical thermal maximum of activity (P. dominula 47.1 °C, P. gallicus 47.6 °C). The metabolic response did not reveal clear adaptations to climate conditions. At low and high temperatures, the metabolic rate of P. dominula was higher, and at intermediate temperatures, we determined higher values in P. gallicus. However, the species exhibited remarkably differing thermoregulatory behaviour at the nest. On average, P. gallicus tolerated a thoracic temperature up to ~41 °C, whereas P. dominula already tried at ~37 °C to keep the thorax below ambient temperature. We suggest this to be an adaptation to the higher mean ambient temperature we measured at the nest during a breeding season. Although we determined for P. dominula a 0.5 °C larger thermal tolerance range, we do not presume this parameter to be solely responsible for the successful distribution of P. dominula. Additional factors, such as the thermal tolerance of the queens could limit the overwintering success of P. gallicus in a harsher climate.

Greenhouse gas (GHG) emissions have been established for recycling of paper waste with focus on a material recovery facility (MRF). The MRF upgrades the paper and cardboard waste before it is delivered to other industries where new paper or board products are produced. The accounting showed that the GHG contributions from the upstream activities and operational activities, with global warming factors (GWFs) of respectively 1 to 29 and 3 to 9 kg CO2-eq. tonne— 1 paper waste, were small in comparison wih the downstream activities. The GHG contributions from the downstream reprocessing of the paper waste ranged from approximately 490 to 1460 kg CO2-eq. tonne —1 of paper waste. The system may be expanded to include crediting of avoided virgin paper production which would result in GHG contributions from —1270 to 390 kg CO2-eq. tonne— 1 paper waste. It may also be assumed that the wood not used for virgin paper production instead is used for production of energy that in turn is assumed to substitute for fossil fuel energy. This would result in GHG contributions from —1850 to —4400 kg CO2-eq. tonne— 1 of paper waste. These system expansions reveal very large GHG savings, suggesting that the indirect upstream and operational GHG contributions are negligible in comparison with the indirect downstream emissions. However, the data for reprocessing of paper waste and the data for virgin paper production are highly variable. These differences are mainly related to different energy sources for the mills, both in regards to energy form (heat or electricity) and fuel (biomass or fossil fuels).

The presence of paper in municipal solid waste (MSW) interferes with the efficiency of composting plants. The compost feedstock to these plants is between 12% and 27% paper on a dry weight basis, with an initial C:N ratio ranging from 32:1 to 57:1. Tests of the last aerobic biodegradability (LAB) of the type of paper present in paper and cardboard packaging were carried out, following UNE-EN 14046 standards. The results obtained, measured through the quantity of CO(2) generated over 45 days, compared with the maximum that could be produced (ThCO(2)), showed that the presence of paper retards, to a great degree, the biodegradation of organic material in general. Specifically, the presence of papers with a degradation D (%) >60% at 45 days (white (W) and recycled paper (R)) could be allowed, but always in proportions that did not exceed 27% in dry weight. These results can be achieved with an industrial level process, pre-treated by trituration.

This study examines the historical relation between carbon dioxide emission and output growth in the Swedish pulp and paper industry from 1973 to 2006. We find that the industry achieved an 80 perc ...

The optimization of supercritical fluid extraction using CO2 for the extraction of contaminants in 15 samples of recycled paper and board (P&B) has been studied. An experimental design was used for simultaneous optimization of the variables involved in both the extraction step and the collection of the extract. Methanol was used as modifier. Several plastisizers such as diethyl phthalate, diisobutyl phthalate, di-n-butyl phthalate, dioctyl adipate, and diethylhexyl phthalate (from 2 to 100 microg/g of paper) were found in the recycled P&B samples. A discriminate analysis applied to all results obtained allow us to classify the samples in three different groups according to the content of recycled pulp (0, 10-30, and > 80% of recycled pulp), the sample thickness (from 600 microm), and the surface treatment of the paper. The analytical behavior and the results are discussed.

The European paper wasp, Polistes dominulus Christ, is an abundant wasp species in South and Central Europe which dispersed to the north in recent times. Polistes dominulus exhibits an energy-extensive mode of life, spending much time resting at the nest, which should be reflected in adaptations regarding gas exchange and standard metabolism. We analysed the resting metabolism (CO2 emission) of Polistes dominulus workers in the ambient temperature range an individual may be exposed to during a breeding season (Ta = 2.4–40.6 °C) via flow through respirometry. Behaviour and endothermic activity were assessed by infrared thermography. With rising Ta, CO2 release followed an exponential increase from 27 to 149 and 802 nl g−1 min−1 at Ta = 3, 20 and 35 °C, respectively. Measurements of the thermal regime at the nest showed that resting P. dominulus are most of the time in the lower range of their standard metabolic curve. A comparison with a “highly energetic” wasp like Vespula sp. revealed that Polistes dominulus not only optimises behaviour but also reduces metabolism to save energy. The CO2 emission patterns changed with ambient temperature, from discontinuous (≤25 °C) to cyclic (25–36 °C) and continuous gas exchange at higher temperatures. A pronounced break appeared in the data progression regarding cycle frequency and CO2 emission per gas exchange cycle between 15 and 10 °C. This striking change in gas exchange features indicates a physiological adaptation to special respiratory requirements at low temperatures. Electronic supplementary material The online version of this article (doi:10.1007/s00360-015-0915-7) contains supplementary material, which is available to authorised users.

Paper, a cheap and ubiquitous material, has great potential to be used as low-cost, portable and biodegradable platform for chemical and biological sensing application. In this paper, we are exploring a low-cost, flexible and reliable method to effectively pattern paper for capturing optical dyes and for flow-based delivery of target samples for colorimetric chemical sensing. In this paper, we target the detection of ammonia (NH 3 ) and carbon dioxide (CO 2 ), two of the important environmental and health biomarkers. By functionalizing the paper platform with diverse cross-reactive dyes sensitive to NH 3 and CO 2 , their selective sensing within a certain pH range, as well as their detection at different concentrations can be achieved. The images of paper based device were captured by a flatbed scanner and processed in MATLAB ® using a RGB model and PCA for quantitative analysis. Paper based devices with readout using ubiquitous consumer electronic devices (e.g. smartphones, flatbed scanner) are considered promising approaches for disease screening in developing countries with limited resources.

Anthropogenic activities are altering levels of atmospheric carbon dioxide (CO2) and tropospheric ozone (O3). These changes can alter phytochemistry, and in turn, influence ecosystem processes. We assessed the individual and combined effects of elevated CO2 and O3 on the phytochemical composition of two tree species common to early successional, northern temperate forests. Trembling aspen (Populus tremuloides) and paper birch (Betula papyrifera) were grown at the Aspen FACE (Free-Air Carbon dioxide and ozone Enrichment) facility under four combinations of ambient and elevated CO2 and O3. We measured, over three years (2006-08), the effects of CO2 and O3 on a suite of foliar traits known to influence forest functioning. Elevated CO2 had minimal effect on foliar nitrogen and carbohydrate levels in either tree species, and increased synthesis of condensed tannins and fiber in aspen, but not birch. Elevated O3 decreased nitrogen levels in both tree species and increased production of sugar, condensed tannins, fiber, and lignin in aspen, but not birch. The magnitude of responses to elevated CO2 and O3 varied seasonally for both tree species. When co-occurring, CO2 offset most of the changes in foliar chemistry expressed under elevated O3 alone. Our results suggest that levels of CO2 and O3 predicted for the mid-twenty-first century will alter the foliar chemistry of northern temperate forests with likely consequences for forest community and ecosystem dynamics.

We describe a latex wet coalescence extrusive coating method that produces up to 10-fold specific photosynthetic rate enhancements by nitrate-limited non-growing cyanobacteria deposited onto paper, hydrated and placed in the gas-phase of small tube photobioreactors. These plant leaf-like biocomposites were used to study the tolerance of cyanobacteria strains to illumination and temperature using a solar simulator. We report sustained CO2 absorption and O2 production for 500 h by hydrated gas-phase paper coatings of non-growing Synechococcus PCC7002, Synechocystis PCC6803, Synechocystis PCC6308, and Anabaena PCC7120. Nitrate-starved cyanobacteria immobilized on the paper surface by the latex binder did not grow out of the coatings into the bulk liquid. The average CO2 consumption rate in Synechococcus coatings is 5.67 mmol m(-2) h(-1) which is remarkably close to the rate reported in the literature for Arabidopsis thaliana leaves under similar experimental conditions (18 mmol m(-2) h(-1) ). We observed average ratios of oxygen production to carbon dioxide consumption (photosynthetic quotient, PQ) between 1.3 and 1.4, which may indicate a strong dependence on nitrate assimilation during growth and was used to develop a non-growth media formulation for intrinsic kinetics studies. Photosynthetic intensification factors (PIF) (O2 production by nitrate-limited cyanobacteria in latex coatings/O2 produced by nitrate-limited cell suspensions) in cyanobacteria biocomposites prepared from wet cell pellets concentrated 100- to 300-fold show 7-10 times higher specific reactivity compared to cells in suspension under identical nitrate-limited non-growth conditions. This is the first report of changes of cyanobacteria tolerance to temperature and light intensities after deposition as a thin coating on a porous matrix, which has important implications for gas-phase photobioreactor design using porous composite materials. Cryo-fracture SEM and confocal microscopy images of cell coating distribution on the paper biocomposite suggest that the spatial arrangement of the cells in the coating can affect photoreactivity. This technique could be used to fabricate very stable, multi-organism composite coatings on flexible microfluidic devices in the gas-phase capable of harvesting light in a broader range of wavelengths, to optimize thermotolerant, desiccation tolerant, or halotolerant cyanobacteria that produce O2 with secretion of liquid-fuel precursors synthesized from CO2 .

This report demonstrates the fastest technique to successfully achieve carboxymethyl cellulose (CMC) from office paper waste, within 30 min at ambient temperature using ultrasonic-assisted method as a source of energy. The obtained CMC was characterized using FTIR, TGA, and NMR techniques to confirm its structure. The FTIR spectrum showed characteristic peaks of carboxymethyl groups and its salt at the wavenumbers of 1585 (C=O) and 1412 (C-O) cm−1. The TGA results of CMC exhibited the loss of carbon dioxide at ca. 260 – 300 °C. Moreover, a higher ash yield of the obtained CMC indicated the substitution of carboxymethyl in the structure. The CMC product structure was confirmed using 13C- and HMBC 2D-NMR. The HMBC 2D-NMR results indicated a correlation between carbonyl and methylene carbons of carboxymethyl groups and protons of pyranose ring, implying that pyranose ring was substituted successfully by monocholoroacetic acid (MCA). The optimal conditions were obtained by using 4.11 ml of 30%w/v NaOH and 1.4 g of MCA in 40 ml of isopropanol at ambient temperature. The resulting CMC showed 0.75 degree of substitution at 18.75 W/ml ultrasonic intensity.

To determine the benthic transformation pathways and fate of carbon associated with secondary-treated pulp and paper mill (PPM) effluent, 13C-labeled activated sludge biomass (ASB) and phytoplankton (PHY) were added, separately, to estuarine intertidal sediments. Over 28 days, 13C was traced into sediment organic carbon, fauna, seagrass, bacteria, and microphytobenthos and into fluxes of dissolved organic carbon (DOC) and dissolved inorganic carbon (DIC) from inundated sediments, and carbon dioxide (CO2(g)) from exposed sediments. There was greater removal of PHY carbon from sediments (∼85% over 28 days) compared to ASB (∼75%). Although there was similar 13C loss from PHY and ASB plots via DIC (58% and 56%, respectively) and CO2(g) fluxes (

Rainbow trout exposed to effluent from a UNOX (oxygen activated sludge) treatment plant were found to exhibit signs of distress during the first hours of exposure. While the final effluent was not acutely lethal at full strength, it was still important to determine the cause of the distress to ensure that the mill's effluents remain in regulatory compliance. The use of a series of effluent manipulations involving pH adjustment and aeration as well as observations of symptoms exhibited by the fish were successful in identifying carbon dioxide as the cause of fish distress for the UNOX-treated effluent. For rainbow trout, the symptoms of exposure to elevated levels of carbon dioxide of 100 mg/L or greater included loss of equilibrium, erratic swimming, gasping at the surface, sinking to the bottom of the test container and paralysis. The fish were found to eventually recover as the carbon dioxide was stripped from the effluent due to aeration during the test. A carbon dioxide concentration of 250 mg/L, however, was found to be lethal to trout A survey of mills using oxygen activated sludge treatment systems indicated that the carbon dioxide levels in effluents from such operations can range from 48 to 251 mg/L. Solutions for eliminating the fish distress and possible mortality associated with such effluents would be to lower the carbon dioxide level to below 100 mg/L by aeration or pH adjustment.

Mineral carbonation is a technology for permanently storing carbon dioxide by reacting with metal oxides containing calcium and magnesium. In this study, we used sea water and alkaline industrial by-product such as paper sludge ash (PSA) for the storage of carbon dioxide through direct carbonation. We found the optimum conditions of both sea water content (mixing ratio of sea water and PSA) and reaction time required in the direct carbonation through various experiments using sea water and PSA. In addition, we compared the amounts of carbon dioxide storage with the cases when sea water and ultra-pure water were separately used as solvents in the direct carbonation with PSA. The amount of carbon dioxide storage was calculated by using both solid weight increase through the carbonation reaction and the contents of carbonate salts from thermal gravimetric analysis. PSA particle used in this study contained 67.2% of calcium. The optimum sea water content and reaction time in the carbonation reaction using sea water and PSA were 5 mL/g and 2 hours, respectively, under the conditions of 0.05 L/min flow rate of carbon dioxide injected at and 1 atm. The amounts of carbon dioxide stored when sea water and ultra-pure water were separately used as solvents in the direct carbonation with PSA were 113 and , respectively. The solid obtained through the carbonation reaction using sea water and PSA was composed of mainly calcium carbonate in the form of calcite and a small amount of magnesium carbonate. The solid obtained by using ultra-pure water, also, was found to be carbonate salt in the form of calcite.

High concentration benzene production in paper and painting industries is a restrictive problem in production line of companies. In this study, removal of high concentrated benzene produced in painting companies was investigated using a Plate Gliding Arc (PGA) reactor. Decomposition of methane and carbon dioxide as the most predominate byproducts of benzene decomposition was also studied using (PGA) reactor. The effect of several parameters such as input power, feed gas flow rate, type of carrier gas, and [CH(4)/CO(2)] flow ratio was studied by two series of experiments. The results show significant conversion (>70%) of high concentration benzene (74000ppm) without using any catalyst. Selectivity of CO(2) and CO was 88% and 10% respectively showing complete oxidation of benzene. The maximum conversion of CH(4) and CO(2) reached 52% and 69%, respectively by using optimum ratio of 3:4. The main results of this study proved removal of high concentration benzene using a low-energy-density reactor. Furthermore, an optimum value for efficient conversion of methane and carbon dioxide was achieved and the energy density of the PGA reactor was evaluated, which shows a good promise for industrial applications.

Waste paper mill sludges originating from different effluent treatment and de-inking installations are complex mixtures of inorganic and organic particles. Due to their favourable physico-chemical, and microbiological characteristics, they may be conveniently reused for different purposes as such or after appropriate pretreatment. Sludges from the Slovenian paper industry were extensively tested for their chemical, stability and sealing properties. During the biodegradability tests, evolutions of greenhouse gases CO2, CH4 and H2 S as well as the concentrations of released volatile organic acids, such as acetic, propionic, butyric, lactic and glycollic acids as the typical degradation products of organic materials, were measured. Some other important parameters of water leachates such as pH, redox potential, content of starch and leachable ions were also evaluated. The results indicate that most of them can be efficiently applied as alternative hydraulic barrier layers for landfill construction and covering instead of the more expensive clay due to their good geomechanical properties, chemical inertness and microbiological stability. Such replacement brings about considerable economical and ecological benefits as the waste is reprocessed as secondary raw material.