Search

It is a challenge to achieve flexibility in purely inorganic piezoelectric materials without organic support, and various thin film flexible inorganic piezoelectric materials has been developed recently. In this work, lead zirconate titanate (PZT) nanofiber membranes were prepared by electrospinning, and a flexible membranes can be obtained by reducing the calcination temperature, and the flexibility was characterized by the three-point method. The fiber membrane was relatively thicker in relative to thin films and confirmed to adsorb Congo Red quickly under the action of ultrasound. The maximum adsorption capacity is 61.78 mg g−1 and saturation time reaches 20 min under ultrasound treatment. In addition, the color change after saturation adsorption can quickly determine the actual load of the fiber membrane. In the future, this load saturation effect can be used to calibrate the relationship between the piezoelectric signal and the adsorption load, so as to obtain more accurate chemical sensors.

Traditional inorganic materials exhibit rigidity owing to the lack of polymer chains in polymer materials or atom slipping in metals. However, nanometerization has been recently proposed for the conversion of inorganic oxide materials into flexible materials. Herein, the flexible inorganic luminescent material, CaTiO3:0.2%Pr3+, was synthesized through electrospinning, and the macroscopic flexibility of pure inorganic CaTiO3:0.2%Pr3+ was achieved. The flexible membrane was characterized via X-ray diffraction, thermogravimetry, scanning electron microscopy (SEM), and photoluminescence analyses. The grain size was analyzed at various calcination temperatures via SEM, and the results suggested that the increase in the calcination temperature resulted in the growth of crystal grains. Studies have reported that the growth of crystal grains is beneficial for improving the luminescence performance; however, to obtain better flexibility, smaller crystal grains are required. This study provides an important reference for the design of flexible inorganic materials.

Traditional Chinese medicine injections (TCMJs) combined with FOLFOX4 regimen could achieve favorable effects in the treatment of gastric cancer. However, the efficacy and safety of different TCMJs combined with FOLFOX4 in the treatment of gastric cancer have not been fully clarified. Due to the fact that there are as many as ten kinds of TCMJs, how to choose an appropriate TCMJ has become an urgent clinical problem. The objective of this network meta-analysis (NMA) is to explore the optimal options among different TCMJs for gastric cancer.

Solid nanogenerators often have a limited charge transfer due to the low contact area. Compared with solid-solid or solid-liquid nanogenerators, liquid-liquid nanogenerators can effectively increase the transferred charge. Limited by the fluidity of the liquid, the precise manipulation of the liquid morphology remains a challenge. In this work, using the surface tension of the droplet to fix the shape, we designed a new liquid-liquid triboelectric nanogenerator by using the immiscible aqueous-aqueous interface, achieving the contact surface charge transfer of 129 nC of a single droplet. This liquid-liquid nanogenerator has been proven to be applicable in humid environments, and the two-phase materials have good biocompatibility and can be used as a good carrier for drugs. Therefore, this nanogenerator is useful for future design of implantable devices and the design of a new type of bionic fully self-powered system has great potential. Meanwhile, such design established the foundation of aqueous electronics and more creation can be achieved by using this route.

Multifunctional composite nanostructure prepared via electrospinning has attracted wide attention. In this study, Fe2O3-carbon composite nanofiber with particle–nanorod structure was successfully prepared via electrospinning and followed calcination. Then, the electromagnetic properties of this material have been fully characterized, and the influence of different preparation conditions on these properties has been studied. In addition, compared to pure [Formula: see text]-Fe2O3 nanoparticles and hollow Fe2O3 nanofibers, the composite nanofibers with a thickness of 2.64[Formula: see text]mm exhibited an additional absorption peak at a frequency of 13.92[Formula: see text]GHz and an enhancement in absorption at a frequency of 15.45[Formula: see text]GHz, which may be attributed to the increase in electrical loss introduced by amorphous carbon and the enhanced magnetic loss resulting from the multi-stage reflection introduced by the particle–nanorod structure. This study shows that the composite of Fe2O3 and carbon, and the introduction of the particle–nanorod structure can improve the microwave absorption efficiency of materials, and more nanocomposites can be designed like this to further improve their electromagnetic properties and absorption efficiency in the future.

At present, wearable electronic sensors are widely investigated and applied for human life usage especially for the flexible piezoelectric sensor based on piezoelectric fibers. However, most of these fiber-based piezoelectric sensors are thin films, which might had poor air permeability, or do not adapt to complex body movements. In this study, a piezoelectric sensing fabric was proposed based on core-spun Cu/P(VDF-TrFE) nanofibrous yarns. These yarns were fabricated by P(VDF-TrFE) as a piezoelectric material and Cu wire as an inner electrode layer through a one-step conjugate electrospinning process. The Cu/P(VDF-TrFE) fabrics showed good flexibility, breathability, mechanical stability, and sensing capability after continuous running for 60 min or after washing. A 4 cm × 4 cm fabric could generate a current of 38 nA and voltage of 2.7 V under 15 N pressure. Once the fabric was fixed onto the clothes, human motion could be monitored by collecting its generated current, and the signal could be wirelessly transmitted onto a smartphone. Therefore, this study may provide a simple and promising approach to design a smart textile for human motion monitoring.

The use of automotive LPG characteristics which are easy to evaporate vaporization and carry. The paper presents a design of extended-range electric vehicle for wall-guided two stroke LPG engine with direct injection combustion system. Based on the modified vehicle LPG spray model, a database describing the characteristics of vehicle LPG fuel was built and imported into the CFD software. And the accuracy of the model is verified by the Schlieren experimental results. The concentration and velocity field of the mixture in the cylinder under different load conditions are numerically analyzed. The analyzed result indicated that the start injection time θ = 60°–70°CA BTDC under part load condition, the plug electrode near the gathering of a richer mixture is easy to be fired at spark ignition time, the obvious formation of mixture in cylinder is formed and the overall air-fuel ratio is above 40: 1. The start-transition working condition and large load conditions in the piston moves upward before closing the exhaust port to start injection LPG. The optimized LPG injection start time θ ensures that the fresh gas is locked in the cylinder when the exhaust port is closed (63°CA ABDC). In the ignition time of the spark plug, an ideal homogeneous mixture in the cylinder is realized.