Search

There are several international transport corridors in Hungary. Záhony railway station is one of the largest hubs in Europe, providing a railway connection between Ukraine and the European Union. Two different railway tracks meet and come together here, such as the standard (1435 mm) and broad (1520 mm) gauges. The availability of a developed infrastructure of the dual gauge on the territory of Hungary presupposes the corresponding development of the railway connection by Ukraine. In order to effectively use the dual gauge line and solve problems of special design, it is necessary to ensure the appropriate train flows. This research aims to provide scientific support for express analysis of the railway routes' competitiveness between Ukraine and the European Union to define the determining factors. The application of such approaches provides a tool for establishing the prospects for the development of existing railway lines, considering their features. Scientific approaches to creating methods for determining the priority areas of railway transport have been further developed. Apart from involving such essential indices as average speed and traffic volumes, the authors added the possibility of considering the presence of lines with such design features as single-track sections, non-electrified, dual gauge, etc., on the route. The theoretical background is applied as a tool for rapid calculations for increasing the competitiveness of the Chop–Záhony dual gauge line.

The article examines the superstructures of the tramway tracks of tramway line No. 1 in Budapest (the capital of Hungary). Since the first appearance of tramways, several technological advancements have been made to serve passenger needs as efficiently as possible. Several types of tramway track superstructure systems can be differentiated, which are implemented differently in each project. Furthermore, these superstructure types have different degradation times (both geometrical and structural), which depend on several factors. Nowadays, visual inspections are no longer considered sufficient in monitoring the tracks’ condition and deterioration, thus it is necessary to consider examinations carried out using the sensors mounted on the vehicles. Adopting appropriate methods, the measured data can be modeled and the life cycle of superstructures and structural elements can be determined as a result of sufficiently long-term studies (i.e., life cycle costs, the whole lifetime, etc.). First, the authors present a review of the relevant international literature, after that they conduct analysis of track geometry parameters of the superstructures related to five sections on the investigated tramway line based on the results of the measurements performed for three consecutive years between 2019 and 2021. The analyses consist primarily in statistical examination of the measured and calculated parameters.

During track construction or ballast bed maintenance, ballast layer compaction quality plays an essential role in the following track irregularity accumulation, its lifecycle, and maintenance costs. The ballast compaction process is characterized by its compaction and the accumulation of the stressed state. The elastic wave propagation methods are an effective way for the identification of the ballast bed compaction properties. The paper presents the theoretical and experimental studies of the ballast consolidation under the vibration loading of the sleeper. The practical laboratory study is given by the 1:2.5 scaled physical model of one sleeper and the corresponding ballast layer box. The measurements of ballast pressure and deformations under the vibration loading in the ballast layer and the photogrammetric recording of the ballast flow are carried out. The measurements demonstrate the accumulation of the residual stresses under the ballast layer. Furthermore, the measurements of elastic wave time of flight (ToF) using the shakers under the sleeper and acceleration sensors under the ballast show the substantial increase of the ToF velocities after the tamping process. Moreover, the distribution of the velocities along the sleeper is spatially inhomogeneous. The numeric simulation using the discrete element method (DEM) of the tamping and the testing processes proves the inhomogeneous wave propagation effect. The modeling shows that the main reason for the wave propagation inhomogeneity is the accumulated residual stress distribution and the minor one – the compaction density. Additionally, a method for identifying wave velocity spatial distribution is developed by wave tracing the inhomogeneous medium. The procedures allow ballast identification in the zones outside the shakers.

The present paper deals with the experimental investigation of interlocking effect of crushed stone ballast material, assessing it as the relationship with the residual and dynamic stresses under the ballast layer during laboratory dynamic tests with the consideration of different boundary conditions. The laboratory experiments were executed with a scaled model of ballast under the sleeper. The measured pressure at the bottom surface of the ballast has two parts: dynamic and residual. The dynamic part depends on the external loading; the residual part remains after unloading. The measured residual stress was observed up to 3 times higher than the stress due to cyclic external loading. The relationship of the residual stress and interlocking effect to ballast particles angularity is analyzed. A simple interpretation of the distribution of residual stress is proposed, that depends on the measured cyclic stress and the elasticity of bounding walls. The study of interlocking effect of ballast could be potentially useful for many practical problems of railway track design as well as for the track maintenance issues.

Unmanned Aerial Vehicles, also known as UAVs, play an increasingly important part in daily life. However, the ever-increasing number of UAVs pose an ever-increasing threat to the transportation infrastructure. Despite their precision and general efficiency, infrastructural-scale Unmanned Aerial Systems (UASs) have a disadvantage regarding their capability of being implanted in the ecosystem. There are several reasons for this, but the primary bottleneck is that their systems are not transparent to society and have very complicated processes. As a result, the authors decided to investigate the functional properties of UASs and make improvements to those properties. Throughout the study, the authors’ primary focus was on analysis, which boosts productivity and ensures a significant level of safety for routine flights. The amount of power that a UAV uses depends on several variables, including the amount of power that its individual components require, the temperature of its surroundings, and the condition of the battery that it is powered by. Therefore, critical parameters and interdependencies are taken into account in the risk assessment strategy for energy-efficient Unmanned Aerial Vehicles (UAVs). In the case of UAVs, the algorithm performs a risk calculation before take-off to estimate the amount of risk that can be associated with the given flight time when using the provided battery. On the one hand, several instances of the pre-take-off state and how its parameters interact are investigated. On the other hand, they demonstrate the calculation of the risk while in flight, which is based on actual flight data.

This paper investigates the usability of touch screens used in mass production road vehicles. Our goal is to provide a detailed comparison of conventional physical buttons and capacitive touch screens taking the human factor into account. The pilot test focuses on a specific Non-driving Related Task (NDRT): the control of the on-board climate system using a touch screen panel versus rotating knobs and push buttons. Psychological parameters, functionality, usability and, the ergonomics of In-Vehicle Information Systems (IVIS) were evaluated using a specific questionnaire, a system usability scale (SUS), workload assessment (NASA-TLX), and a physiological sensor system. The measurements are based on a wearable eye-tracker that provides fixation points of the driver’s gaze in order to detect distraction. The closed road used for the naturalistic driving study was provided by the ZalaZONE Test Track, Zalaegerszeg, Hungary. Objective and subjective results of the pilot study indicate that the control of touch screen panels causes higher visual, manual, and cognitive distraction than the use of physical buttons. The statistical analysis demonstrated that conventional techniques need to be complemented in order to better represent human behavior differences.

This paper presents a short literature review related to the fragmentation of the railway crushed ballast particles. With the help of the processed articles with the main topic of discrete element modelling (DEM) we aim to provide some insight into the international achievements and forward progress of the subject. Rock materials as granular elements can be investigated from several perspectives. The elements can be examined in laboratory conditions purely from the quarry, or even by obtaining already fragmented particles from the real railway tracks. In addition, DEM models can be created by using computer software. This article tackles only a small segment of the literature. Though each DEM topic was unique, they all involved examination of degradation of particles in some way. This review focuses on model building, including particle construction and calibration. The selected publications do not cover the current state of the entire DEM research related to ballast degradation.

The most important thing nowadays is to use available resources to develop infrastructure as efficiently as possible. In this regard, evaluating the deterioration of tramway tracks is critical from both a technical and an economic viewpoint. In Hungary, seven types of superstructure systems are currently differentiated in the case of tramway transport, but the geometrical deterioration, lifecycle, and lifecycle cost of the tramway tracks are not accurately known. The current study aimed to evaluate and compare the results of track geometry measurements of two different “open” tramway superstructure systems depending on their traffic load and age. The geometry measurements we re executed by TrackScan 4.01 instrument, developed and maintained by a Hungarian developer company called Metalelektro Méréstechnika Ltd. The evaluation of the measurements showed a clear relationship between the traffic load, age, and track deterioration. Based on the results, it can be generally stated, concerning “open” superstructure systems, that regardless of the “open” superstructure system or the level of traffic load, the average value of alignment is decreasing; however, the average value of the longitudinal level is increasing. Furthermore, the deterioration of an older ballasted track with lower traffic is similar to that of a younger ballasted track that has a higher traffic load. Another significant result was that the deterioration of the track gauge parameter in the case of concrete slab tracks is clearly described as the broadening of the track gauge.

Automatic transmission is a key factor for autonomous driving. The transmission condition is highly affected by the quality and quantity of transmission oil in the system. However, the oil condition is not monitored in the system, and the oil change interval and method are still a subject of discussion. This paper analyzes the effects of oil changes in automatic transmissions. The measurements were carried out before and after the oil change with the same external conditions. With the vibration measurement method, data can be collected without disassembling the parts and during operational conditions. Furthermore, time- and frequency-based analyses were conducted to compare different transmissions’ operations. The results have shown that the effect of oil degradation is measurable on the amplitude of the signals and, therefore, predictable with vibration diagnostics. During the evaluation, the maximum values were compared on measurements with at least a 2-s length.

The article deals with DIC (Digital Image Correlation) tests on steel plates used in the automotive and railway industries, as well as in the construction industry. The most critical part of DIC tests is the quality of proper surface preparation, painting, and random patterns. The paint mediates the deformation of the optical systems, and its quality is paramount. The authors’ goal in this research is to determine the optimal dye–cleaning–drying time parameters for DIC studies. Commercially available surface preparation and cleaning agents were tested alongside commercially available spray paints. Standard and specific qualification procedures were applied for the measurements. Once the appropriate parameters were determined, the results were validated and qualified by GOM ARAMIS tests. Based on the results, DIC measurements can be performed with higher accuracy and safety in laboratorial and industrial conditions, compared to the traditional deformation measurements executed by dial gauges or linear variable differential transformers.

This paper deals with the time-frequency characteristic analysis for track geometry irregularities using field data recorded by a comprehensive track inspection train. The parameters of the track gauge and the left and right rail alignment are considered to identify their characteristic wavelengths and the locations of their waveforms. In addition to the conventional time and frequency domain analysis, auto-adaptive signal decomposition techniques are used on four pre-selected track sections. During the time series analysis of the track gauge, the cumulative difference from the mean value is calculated, which makes it possible to distinguish the track section constructed with non-standard initial track gauges. The sensitive wavelengths of the track irregularities are obtained from the proper allocation of wavelength ranges in the Fourier Amplitude Spectrum of the original signal and the Fourier transform of the components detected by the Variational Mode Decomposition. This analysis can elucidate the wavelengths and positions of track irregularities that affect vehicle responses.

The current paper concerns the investigation of CC (Concrete Canvas), a unique building material from the GCCM (geosynthetic cementitious composite mat) product group. The material is suitable for trench lining, trench paving, or even military construction activities, while the authors’ purpose is to investigate the application of the material to road and railway substructure improvement. This research was carried out to verify the material’s suitability for transport infrastructure and its beneficial effects. The authors’ previous study reported that the primary measurements were puncture, compression, and the parameters evaluated in four-point bending (laboratory) tests. However, based on the results, finite element modeling was not feasible because the testing of the composite material in a single layer did not provide an accurate indication. For this reason, the material characteristics required for modeling were investigated. A unique, novel testing procedure and assembly were performed, wherein the material was loaded under quasi-realistic conditions with a crushed stone ballast sample and other continuous particle size distribution samples in a closed polyethylene tube. In addition, the deformation of the material following deformed bonding was measured by computed tomography scanning, and the results were evaluated.

The maintenance of the ballast substructure is an important cost-driver for railway systems. The problem is that today’s condition monitoring methods are insufficient to collect detailed data on the compaction and stress allocation inside the ballast bed. That makes it challenging to improve the maintenance technology and organization. This study aimed to investigate the applicability of the ultrasound method for analyzing the state of stress of sand-soil and the relation between the residual stress and wave propagation velocity. The experiments on the sand in a box with different allocations of the ultrasonic receivers and pressure measurement cells were produced under different external loading. In addition, the vertical and horizontal stress distributions were measured. The results showed a correlation between the test load, the state of stress, and the ultrasound propagation velocity. Moreover, the residual stresses after the loading cycles were analyzed.

This paper summarizes the authors' up-to-date results in the research topic of railway ballast particles' breakage test with individual laboratory test. In the past few years there were a ...

This paper demonstrates the results in the research topic of the railway ballast particles’ breakage test with unique laboratory test. The most railway lines in the world have so called traditional superstructure (ballasted tracks). In the past few years there were a lot of railway rehabilitation projects in Hungary, as well as abroad. Nowadays cannot be expected that there is enough quantity of railway ballast in adequate quality, because of the modifications and restrictions in the related regulations in Hungary since 2010. In Hungary there are only a few quarries which are able to ensure adequate railway ballast material for construction and maintenance projects for speed values between 120 and 160 km/h. This may cause supply and quality risk in production of railway ballast. The authors’ research’s main goal is to be able to simulate the stress-strain effect of ballast particles in real and objective way in laboratory conditions as well as in discrete element modelling.

In this paper the authors partially summarize the results of a research on glued insulated rail joints with fiber-glass reinforced plastic fishplates (brand: Apatech) related to own executed labora...

This article summarizes the research results related to our own conducted extensive laboratory tests of polymer composite and steel fishplated glued insulated rail joints (GIRJs), namely axial tensile tests as well as vertical static and dynamic tests. The investigation dealt with the examination of GIRJs assembled with steel and special glass-fiber reinforced plastic (polymer composite) fishplates, both of them for CWR railway tracks (i.e. so-called gapless tracks or, in other words, railway tracks with continuously welded rails). The exact rail joint types were MTH-P and MTH-AP, consistently. The MTH P types have been commonly applied for many years in the CWR tracks in Europe, mainly in Hungary. The MTH-AP rail joints consist of fishplates that are produced by the APATECH factory (Russia). They are made of a fiberglass-amplified polymer composite material at high pressure and controlled temperature. This solution can eliminate electrical fishplate lock and early fatigue failures just as it can ensure adequate electrical insulation. The advantage of such rail joints can be that they are probably able to ensure the substitution of the glued insulated rail joints with relatively expensive steel fishplates currently applied by railway companies, e.g. Hungarian State Railways (MÁV). The aim of the mentioned research summarized in this paper is to formulate recommendations on technical applicability and on the technological instructions that are useful in everyday railway operation practice on the basis of the measurements and tests carried out on rail joints in laboratory.

This paper summarizes the results of a R&D work in 2014. Fivedifferent types of andesite railway ballast material with differentLARB (%) (Los Angeles abrasion) as well as MDERB (%)(Micro-Deval abrasion) values were investigated in laboratorywith pulsating test which models the real condition muchbetter (the used parameters were determined accordance withinternational dynamic design method). Grain size distributionsrelated to the five several aggregates were defined beforeand after pulsating tests. Particle breakages were then calculatedby different method publicized in international literature.Relationships were searched between particle breakages dueto laboratory test and LARB (%) as well as MDERB (%) valuesof railway ballast samples. Time interval (cycle) of ballastcleaning work were attempted to compute with help of specialparameters used by Hungarian and other railway companiesunderlined the limits of calculation method. Finally recommendationswere formulated related to use of this new laboratorytest method for estimation of ballast particle breakage.

Investigation of the reinforcement and stabilisation effect of geogrid layers under railway ballastThis paper deals with the issue of the stabilization of railway track geometry. It details the published results in numerous international journals. Having analysed the cited publications the paper deals with a new research topic related to geogrid-reinforced railway ballast. A research team of the Department of Transport Infrastructure and Municipal Engineering at the Szechenyi Istvan University would like to continue working on this research topic.

There are no design parameters related to speeds exceeding 160 km/h in the effective Hungarian railway design rules. In the relevant international standard (ENV 13803) a similar speed limit is 300 km/h. This paper deals with the comparative of these regulations. Parameters of two transition curves used in Hungary and other used in Austria are determined. The importance of the new design parameters provided by ENV 13803 is assessed. It is demonstrated that the usability of the clothoide transition curves is unnecessarily restricted for the speeds v ≤120 km/h in the Hungarian regulations.