Search

Ternary nitride semiconductors with wurtzite-derived crystal structures are an emerging class of materials for optoelectronic applications compatible with GaN and related III-V compounds. In particular, II-IV-V2 materials such as ZnSnN2 and ZnGeN2 have been very actively studied for applications in photovoltaics and light emitting devices. However, many other possible wurtzite-derived ternary nitrides have not been reported, and hence their optical and electrical properties remain unknown. Here, we report on Zn2SbN3-the first Sb-based nitride and a photoactive semiconductor. Surprisingly, Zn2SbN3 contains Sb in the highest (5+) oxidation state, and in the unusual tetrahedral coordination. This new Zn2SbN3 material has a solar-matched 1.6-1.7 eV band gap and shows near-band-edge room-temperature photoluminescence, demonstrating its promise as an optoelectronic semiconductor. Finally, Zn2SbN3 can be synthesized at low temperature under a wide range of processing conditions, despite being metastable according to theoretical calculations. All these results, as well as the band position measurements, indicate that Zn2SbN3 is a promising emerging semiconductor for applications as an absorber in photovoltaic-and photoelectrochemical solar cells.

Organic photovoltaics (OPV) are a sustainable and inexpensive source of energy comprised of a mixture of an electron-donating and an electron-accepting material (often a polymer and fullerene derivative, respectively) to create a bulk heterojunction (BHJ). However, these devices are held back by low efficiencies. Improving the efficiency in a systematic way requires a comprehensive understanding of the device function and microstructure, but directly imaging the subsurface active layer structure is challenging. Here we demonstrate that ptychography may be used to image the OPV active layer with good film stability and materials contrast in both polymer:fullerene and all-polymer BHJ films. This is possible using soft X-ray ptychography available at the Advanced Light Source beamline 5.3.2.1. We achieve a resolution of 30-50 nm with no discernible radiation damage and discuss the potential for further improvements. This characterization technique could complement widely used electron microscopy and soft X-ray scattering.

Halide perovskites are of great interest because of their large potential for a broad range of applications, such as photovoltaics, light-emitting diodes, and photodetectors. However, currently the state-of-the-art highly emissive halide perovskite materials contain toxic lead ions, and the synthesis of color-stable efficient blue-emissive perovskite analogs remains challenging. The discovery of lead-free, non-toxic halide materials with efficient blue light emission is promising for practical light-emitting applications. Here, we have discovered a series of highly blue-emissive all-inorganic Cu(I)-containing rare-earth halide compounds in the solid state at room temperature. The Cu(I) ions in the compounds show a 3-coordination geometry with the halide ions and connect Sc-Cl octahedra to form clusters in alternating layers, which play a crucial role in the regulation of the electronic structure and emission properties of this series of rare-earth halide cluster compounds.

© 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim Many technologically critical materials are metastable under ambient conditions, yet the understanding of how to rationally design and guide the synthesis of these materials is limited. This work presents an integrated approach that targets a metastable lead-free piezoelectric polymorph of SrHfO3. First-principles calculations predict that the previous experimentally unrealized, metastable P4mm phase of SrHfO3 should exhibit a direct piezoelectric response (d33) of 36.9 pC N−1 (compared to d33 = 0 for the ground state). Combining computationally optimized substrate selection and synthesis conditions lead to the epitaxial stabilization of the polar P4mm phase of SrHfO3 on SrTiO3. The films are structurally consistent with the theory predictions. A ferroelectric-induced large signal effective converse piezoelectric response of 5.2 pm V−1 for a 35 nm film is observed, indicating the ability to predict and target multifunctionality. This illustrates a coupled theory-experimental approach to the discovery and realization of new multifunctional polymorphs.

Lithium rich layered materials are an interesting class of materials which exploit both anionic and cationic redox reactions to store energy upwards of 250 mA h g-1. This paper aims to understand the nature of the redox reactions taking place in these compounds. Li2RuO3 was used as the base compound, which is then compared with compounds generated by partially substituting Ru with Ti and Fe respectively. Electrochemical tests indicate that Fe substitution in the sample leads to an improvement in capacity, cycle life and reduction of potential decay. To elucidate the reason for this improvement in operando diffraction experiments were carried out, highlighting the formation of a secondary de-lithiated phase. The distortion of the pristine structure eventually induces frontier orbital reorganization leading to the oxygen redox reaction resulting in extra capacity. Local changes at Fe and Ru ions are recorded using in operando X-ray absorption spectroscopy (XAS). It was noted that while Ru undergoes a reversible redox reaction, Fe undergoes a significant irreversible change in its coordination environment during cycling. The changes in the coordination environment of oxygen and formation of O2n- type species were probed in situ using soft X-rays.

© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim In this work, the detailed morphology studies of polymer poly(3-hexylthiophene-2,5-diyl) (P3HT):fullerene(PCBM) and polymer(P3HT):polymer naphthalene diimide thiophene (PNDIT) solar cell are presented to understand the challenge for getting high performance all-polymer solar cells. The in situ X-ray scattering and optical interferometry and ex situ hard and soft X-ray scattering and imaging techniques are used to characterize the bulk heterojunction (BHJ) ink during drying and in dried state. The crystallization of P3HT polymers in P3HT:PCBM bulk heterojunction shows very different behavior compared to that of P3HT:PNDIT BHJ due to different mobilities of P3HT in the donor:acceptor glass. Supplemented by the ex situ grazing incidence X-ray diffraction and soft X-ray scattering, PNDIT has a lower tendency to form a mixed phase with P3HT than PCBM, which may be the key to inhibit the donor polymer crystallization process, thus creating preferred small phase separation between the donor and acceptor polymer.