Search

The Cu/Ti composite coatings were prepared by the mechanical ball milling, the CuO/TiO2 and Cu2O/TiO2 composite photocatalytic films were obtained by the subsequent oxidation process. The microstructure of the composite films was analyzed by X-ray Diffraction (XRD）and scanning election microscope (SEM). The photocatalytic activity was evaluated, the effects of ball milling time on the formation of the Cu/Ti coatings were investigated, and the effects of the oxidation temperature and oxidation atmosphere on microstructure and photocatalytic activity of the films were studied. The results illustrate that the ball milling time has significant effects on the formation of the coatings and the coatings are continuous and compact by ball milling for 15 h. The photocatalytic activity of the CuO/TiO2 composite films is increased first and then decreased with the oxidation temperature increases, and the photocatalytic activity is the best at 500 °C. The CuO/TiO2 composite films are obtained by the oxidation of Cu/Ti coatings at 500 °C for 15 h in the air, while the Cu2O/TiO2 composite films are oxidized in carbon atmosphere. Photocatalysis efficiency of the films is obviously enhanced with the help of the p-n junction heterostructure in the Cu2O/TiO2 composite films.

Low mechanical strength, especially at high temperatures, is the key problem that limit the application of FeCrAl alloys as the accident tolerance fuel (ATF) cladding materials. Dispersion strengthening by carbide nanoparticles is an effective way to improve mechanical properties at high temperatures. In this work, an ultrafine grained FeCrAl-0.6 wt.% ZrC alloys with excellent mechanical properties were fabricated successfully by mechanical milling and spark plasma sintering. The effect of milling speed on powder characteristics, microstructure and mechanical properties of FeCrAl alloys were investigated. The particle size of the powders increase significantly after milling at 400 rpm, while it has a lower oxygen content. Increasing the milling speed decreased the resultant grain size and improved relative density. Transmission electron microscope (TEM) demonstrated the nano ZrC particles uniformly distributed in the matrix at higher milling speed, which effectively promotes grain refinement and dispersion strengthening. The results of mechanical properties show that the tensile strength, percentage elongation and hardness of FeCrAl-0.6 wt.% ZrC alloys at room temperature (RT) reached up to 1.05 GPa, 349.86 HV and 12.1%, respectively, after milling at 400 rpm. It is worth noting that the FeCrAl-0.6 wt.% ZrC alloy also exhibited a good high-temperature strength more than 110 MPa at 800 ℃, which is about 55.4% and 24.7% higher than previously reported FeCrAl-0.5 wt.% ZrC and FeCrAl-1.0 wt.% ZrC alloys, but the plasticity is reduced. The results demonstrated that the excellent mechanical properties were not only attributed to the dispersion strengthen by nanosized ZrC, a good interface bonding between Fe matrix and nanosized ZrC, but also the ultra-fine grained structure induced by the milling process.

The fatigue crack propagation behavior on the surface of machining notches of Alloy 690TT (thermally treated) was investigated in room-temperature air environment and in simulated pressurized water reactor (PWR) environment with saturated air at 325°C. The results showed that more than one crack formed on the notch surface and the crack propagation paths were transgranular with some branching. The grain size also had some effect on the crack propagation path but had no significant effects on the crack growth rates (CGRs). The CGR vs. a curve could be divided into two stages in air environment and three stages in simulated PWR environment. The corrosive environment promotes crack propagation in the macroscopic crack propagation stage. Different load frequencies express similar crack propagation process, but decreasing frequency can assist the corrosion fatigue crack nucleation and propagation on the notch surface.

The NiO/TiO2 composite films with the NiO content of 3 %, 5 %, 10 %, 13 %, 15 % and 20 % were prepared by mechanical coating technology and subsequent oxidation process. The composition and microstructure of the films were analyzed by X-ray Diffraction (XRD), scanning electron microscope (SEM), and energy dispersive spectroscopy (EDS). The photocatalytic activity was evaluated and the effects of the content of NiO on microstructure and photocatalytic activity of the films were studied. The results show that NiO particles are dispersed in the Ti coatings, and the NiO concentration in the inner layer of the coatings is higher than in the outer layer. With the addition of NiO in the NiO/Ti coating, the ductility is deteriorated and the thickness is reduced of the NiO/Ti coatings. The films with NiO/TiO2/Ti composite microstructure are obtained by the oxidation of NiO/Ti coatings. Photocatalytic efficiency of the films is obviously enhanced with the help of the p-n junction heterostructure in the NiO/TiO2 films. The optimum content of NiO is about 13 %, and the degradation rate of methyl orange solution reaches the maximum value of 88.44 %. DOI: http://dx.doi.org/10.5755/j01.ms.24.4.19266

Titanium coatings were prepared on the surface of 1mm ZrO2 balls by mechanical ball mill, then the coatings were oxidized to photocatalytic TiO2 films at 400 ~ 600 °C. X-Ray Diffraction, Scanning Electron Microscope, Energy Dispersive Spectroscopy and Optical Microscope were used to analyze the microstructure and crystal form of the films. The photocatalytic activity of the samples was also evaluated. After that, the effects of oxidation temperature on the microstructure and photocatalytic activity of the films were discussed. The results show that the fabricated coatings are uneven, with average thickness of 60 μm. In the process of oxidation, oxygen is imported into the inner coatings by the gaps existed in the Ti coatings, which makes the Ti particles oxidize from surface to core, finally the films with TiO2 + Ti composite microstructure are obtained. The films oxidized at 500 °C have the best photocatalytic performance with the degradation rate of methyl orange solution 79.08 %, this owing to the existence of anatase and the TiO2+Ti composite microstructure. The result will provide theoretical basis for the fabrication of efficient photocatalytic film.DOI: http://dx.doi.org/10.5755/j01.ms.23.2.15590

The ribbons of NdFeB/α-Fe composite alloy were prepared by melt spinning and post crystallizing technique. The element distributions and phase component of both surfaces of as-spun ribbons were measured by energy dispersive spectrometry (EDS) and X-ray diffraction (XRD). Because of the centrifugation, a segregation of B, Fe, and Nd concentrations was observed at the cross section. After crystallizing annealing, the element concentration segregation still existed in the as-crystallized ribbons. Due to the segregation of B, Fe, and Nd, the B-rich phase was observed near the wheel side surface. The B-rich phase may deteriorate the magnetic property of NdFeB/α-Fe composite alloy.