Search

Paper bookbindings have been disregarded for centuries by scholars since they were only considered temporary covering materials for manuscripts and books. Recently, there is a willingness to reconsider these bindings and to evaluate their role. Thanks to the collaboration with the Marciana National Library in Venice, which stores an impressive collection of 849 detached bindings, the current research provides a chemical-physical elucidation about the composition and the manufacture of paper bookbindings realized between the 16th and the eighteenth century in the Venetian area. A selection of bookbindings was analysed by the means of complementary methods (thickness measurements, Attenuated Total Reflection—Fourier-Transform Infrared Spectroscopy (ATR-FTIR), Pyrolysis–Gas Chromatography–Mass Spectrometry (Py-GC–MS) and X-Ray Fluorescence (XRF)). Data evidence the presence of cellulose as the main component of paper pulp; hemicellulose and lignin were identified too, probably related to the presence of linen/hemp rags in the paper production. Gelatine was detected muck likely related to paper sizing; among inorganic additives CaCO3 was found in all samples. The presence of waxy material may be due to past undocumented conservation treatments. [ABSTRACT FROM AUTHOR]

In the engine of heavy trucks, the built-in fuel filter assumes the role of "lungs". The core of the filter, namely the fuel filter paper, acts as a filter for small impurities and separates oil and water. In order to be able to separate minute impurities from the fuel, in this study, we prepared a novel fuel oil filter paper with high efficiency and high dust holding capacity based on wet-laid forming by laminating PBT/PP two-component melt-blown nonwoven material and cellulose nanocrystals (CNC)-doped cellulose wood fiber pulp with the fiber mesh combination forming technology. The effects of the CNC mixing ratio, surface density of melt-blown nonwoven material layer, surface density of cellulose wood pulp paper layer and calendaring pressure on the pore size and filtration performance of the composite samples were investigated, and the filtration efficiency of the composite samples on the tiny impurities in the fuel were also studied. The results showed that the novel composite fuel filter paper material prepared by the combined forming technology of fibrous web had high filtration efficiency and dust holding capacity, and the filtration efficiency of the composite samples could respectively reach 99.90% and 99.52% for particles larger than 14 μm and 4 μm in diameter in the fuel. At the same time, the dust holding capacity of the composite sample can reach up to 27.63 mgcm−2. [ABSTRACT FROM AUTHOR]

The pulp and paper industry is critical to global industrial and economic development. Recently, India's pulp and paper industries have been facing severe competitive challenges. The challenges have impaired the environmental performance and resulted in the closure of several operations. Assessment and prediction of the performance of the Indian pulp and paper industry using various parameters is a critical task for researchers. This study proposes a framework for performance assessment and prediction based on Data Envelopment Analysis (DEA), Artificial Neural Networks, and Deep Learning (DL) to assist industry administration and decision-making. We presented a case study based on eight industries to demonstrate the methodology's applicability. This study analyses and predicts industry performance based on sample data observations over 30 years. The result suggests the DEA-DL-based efficiency prediction has an overall MSE of 0.08 compared with the actual efficiency. Furthermore, the efficiency rankings are compared between the three techniques. The results suggest that the integrated DEA-DL method is primarily accurate in most scenarios with the actual values. The findings of this study provide a comprehensive analysis of environmental performance for policymakers. [ABSTRACT FROM AUTHOR]

In this paper, by a simple hydrothermal method vertically aligned ZnO nanorod arrays were grown on the carbon fiber paper (CFP) and then through a facile chemical bath deposition method CuO nanosheets were loaded on ZnO nanorod arrays, following by thermal spraying method, carboxylated carbon nanotubes (CCNTs) were successfully integrated with CuO/ZnO@CFP to form a binder-free CuO/ZnO-CCNT@CFP sensor. The sensor shows enhanced sensing activity for baicalein and luteolin determination due to the improved structural integration and synergism of different electrode material components. Remarkably, the CuO/ZnO-CCNT@CFP sensor showed good linear relationships over wide concentration ranges of 0.03–0.70 µM and 0.70–20 µM for baicalein and 0.03–0.45 µM and 0.45–8.5 µM for luteolin detection, with the detection limits of 1.7 nM for baicalein and 0.5 nM for luteolin, respectively. More importantly, the CuO/ZnO-CCNT@CFP sensor was utilized in the simultaneous determination of baicalein and luteolin, delivering linear ranges of 0.4–14 µM (baicalein) and 0.2–6 µM (luteolin) with the limit of detection of 0.05 µM and 0.03 µM, respectively. In addition, the developed CuO/ZnO-CCNT@CFP electrode was further investigated to detect baicalein and luteolin in traditional herbal medicine samples, showing satisfied results in comparison with analytic results from high performance liquid chromatography. [ABSTRACT FROM AUTHOR]

In 1980, Prof. Bimla Buti derived, for the first time, an exact solution for localized nonlinear ion-acoustic waves in a plasma with two electron components. Her theory predicted that in the presence of a second electron component, ion-acoustic holes (i.e., solitons with density dips) can exist in addition to regular ion-acoustic solitons having density humps. In 1982, Temerin, et al. [1] reported the observations of ion holes in the Earth's auroral acceleration region between 6000 and 8000 km altitude by S3-3 spacecraft, thus confirming the theoretical predictions of Buti's model. Later on, ion holes were observed on auroral field lines by the Viking spacecraft [2,3] and the Polar spacecraft [4]. It is indeed a nice example where theory leads space experiments and observations. [ABSTRACT FROM AUTHOR]

In the process of conservation mounting, starch paste made from wheat flour is the glue of choice to paste reinforcing strips and backing papers, often Xuan paper, for mending and decorating aged and damaged paper-based Chinese artworks. To keep objects intact and select appropriate conservation materials, this research explored the applicability of near-infrared (NIR) spectroscopy coupled with multivariate analysis for the characterization of contemporary unsized Xuan paper with and without starch. In particular, partial least squares (PLS) regression was used to predict the degree of polymerization (DP) of the paper, i.e., one of the most important properties of paper materials, and principal component analysis (PCA) was used to detect starch and to distinguish between papers with different amounts of starch. Using 12 contemporary unsized Xuan papers, the NIR-PLS method for DP prediction was validated, and the best-performed model was generated using the logarithmic transformation of DP−1 as a response variable, with root mean square error of prediction (RMSEP) of DP 128. The NIR-PCA method was also found to be applicable to separate starch-free papers and papers treated with starch, and the results indicate that the higher the content of starch, the better PCA classification performs. This research provides supporting data for the non-destructive characterization of Xuan paper-based objects and differentiates between Xuan paper before and after treatment with starch. [ABSTRACT FROM AUTHOR]

Mechanochromic photonic crystals are attractive due to their force-dependent structural colors; however, showing unrecordable color and unsatisfied performances, which significantly limits their development and expansion toward advanced applications. Here, a thermal-responsive mechanochromic photonic crystal with a multicolor recordability-erasability was fabricated by combining non-close-packing mechanochromic photonic crystals and phase-change materials. Multicolor recordability is realized by pressing thermal-responsive mechanochromic photonic crystals to obtain target colors over the phase-change temperature followed by fixing the target colors and deformed configuration at room temperature. The stable recorded color can be erased and reconfigured by simply heating and similar color-recording procedures respectively due to the thermoswitchable on-off mechanochromism of thermal-responsive mechanochromic photonic crystals along with solid-gel phase transition. These thermal-responsive mechanochromic photonic crystals are ideal rewritable papers for ink-freely achieving multicolor patterns with high resolution, difficult for conventional photonic papers. This work offers a perspective for designing color-recordable/erasable and other stimulus-switchable materials with advanced applications. Mechanochromic photonic crystals are extremely attractive due to their force-dependent structural colors yet are limited by unrecordable color and unsatisfactory performances. Here, the authors report a thermal-responsive mechanochromic photonic crystal with multicolor recordability-erasability. [ABSTRACT FROM AUTHOR]

It is crucial to develop high porosity and permeability carbon fiber paper for improving the performance of proton exchange membrane fuel cell. Herein, Porous carbon paper with gradient structure (GCP) was prepared by the process of impregnation with a solution of phenolic resin /carbon black composites, overlayer molding, carbonization and graphitization. Specially, conductive carbon black was modified by silane coupling agent (KH-550) and in-situ polymerization with phenolic resin to improve its dispersion uniformity. The microstructure, porosity, gas permeability, electric resistance and mechanic properties of the as-prepared GCP are characterized. The resultant GCP has a gradual transition of porosity from bottom layer to top layer, which constitutes diffusion channels conducive to the transport of gas and liquid. In addition, GCP exhibits superior gas permeability, conductivity, corrosion resistance and tensile strength over commercial carbon paper (CCP). It has potential application prospects for further improving the performance of fuel cells. [ABSTRACT FROM AUTHOR]

Nucleic acid amplification testing has great potential for point-of-need diagnostic testing with high detection sensitivity and specificity. Current sample preparation is limited by a tedious workflow requiring multiple steps, reagents and instrumentation, hampering nucleic acid testing at point of need. In this study, we present the use of mixed cellulose ester (MCE) paper for DNA binding by ionic interaction under molecular crowding conditions and fluid transport by wicking. The poly(ethylene) glycol-based (PEG) reagent simultaneously provides the high pH for alkaline lysis and crowding effects for ionic binding of the DNA under high salt conditions. In this study, we introduce Paper-based Abridged Solid-Phase Extraction with Alkaline Poly(ethylene) Glycol Lysis (PASAP). The anionic mixed cellulose ester (MCE) paper is used as solid phase and allows for fluid transport by wicking, eliminating the need for pipetting skills and the use of a magnet to retain beads. Following the release of DNA from the cells due to the lytic activity of the PASAP solution, the DNA binds to the anionic surface of the MCE paper, concentrating at the bottom while the sample matrix is transported towards the top by wicking. The paper was washed by dipping it in 40% isopropanol for 10 s. After air-drying for 30 s, the bottom section of the paper (3 mm × 4 mm) was snapped off using the cap of a PCR tube and immersed in the colourimetric loop-mediated isothermal amplification (cLAMP) solution for direct amplification and colourimetric detection. The total sample processing was completed in 15 min and ready for amplification. cLAMP enabled the detection of 102 CFU/mL of Escherichia coli (E. coli) from culture media and the detection of E. coli in milk < 103 CFU/mL (10 CFU) after incubation at 68 °C for 60 min, demonstrating applicability of the method to complex biological samples. [ABSTRACT FROM AUTHOR]

Wax printing is the most widely used method for fabricating microfluidic paper-based analytical devices (μPADs), but it still suffers from disadvantages like discontinuation of wax printers and need for additional equipment for heating treatment. To address these issues, this work initially describes a new class of wax printing approach for high-precision, batch fabrication of μPADs using a household 3D printer. It only involves a one patterning step of printing polyethylene wax into rice paper body. Under optimized parameters, a fabrication resolution, namely the minimum hydrophilic channel width, down to ~189 ± 30 μm could be achieved. In addition, the analytical applicability of such polyethylene wax-patterned μPADs was demonstrated well with enhanced colorimetric detection of dopamine as a model analyte by combining metal-organic framework (MOF) based nanoenzymes (ZIF-67) with a smartphone (for portable quantitative readout). The developed nanosensor could linearly detect dopamine over a concentration range from 10 to 1000 μM, with a detection limit of ca. 2.75 μM (3σ). The recovery results for analyzing several real samples (i.e., pig feed, chicken feed, pork and human serum) were between 91.82 and 102.79%, further validating its good detection accuracy for potential practical applications in food safety and medical diagnosis. [ABSTRACT FROM AUTHOR]

Purpose: Paper-based artifacts hold significant cultural and social values. However, paper is intrinsically fragile to microorganisms, such as mold, due to its cellulose composition, which can serve as a microorganisms' nutrient source. Mold not only can damage papers' structural integrity and pose significant challenges to conservation works but also may subject individuals attending the contaminated artifacts to health risks. Current approaches for strain identification usually require extensive training, prolonged time for analysis, expensive operation costs, and higher risks of secondary damage due to sampling. Thus, in current conservation practices with mold-contaminated artifacts, little pre-screening or strain identification was performed before mold removal, and the cleaning techniques are usually broad-spectrum rather than strain-specific. With deep learning showing promising applications across various domains, this study investigated the feasibility of using a convolutional neural network (CNN) for fast in-situ recognition and classification of mold on paper. Methods: Molds were first non-invasively sampled from ancient Xuan Paper-based Chinese books from the Qing and Ming dynasties. Strains were identified using molecular biology methods and the four most prevalent strains were inoculated on Xuan paper to create mockups for image collection. Microscopic images of the molds as well as their stains situated on paper were collected using a compound microscope and commercial microscope lens for cell phone cameras, which were then used for training CNN models with a transfer learning scheme to perform the classification of mold. To enable involvement and contribution from the research community, a web interface that actuates the process while providing interactive features for users to learn about the information of the classified strain was constructed. Moreover, a feedback functionality in the web interface was embedded for catching potential classification errors, adding additional training images, or introducing new strains, all to refine the generalizability and robustness of the model. Results & Conclusion: In the study, we have constructed a suite of high-confidence classification CNN models for the diagnostic process for mold contamination in conservation. At the same time, a web interface was constructed that allows recurrently refining the model with human feedback through engaging the research community. Overall, the proposed framework opens new avenues for effective and timely identification of mold, thus enabling proactive and targeted mold remediation strategies in conservation. [ABSTRACT FROM AUTHOR]

A novel electrochemical sensor for paraquat determination was facilely developed using nanocomposites of cellulose incorporated with manganese oxide (MnO2@cellulose) modified screen-printed carbon electrode (SPCE). In this study, SPCE was fabricated on a low-cost poster paper, and nanocellulose from sugarcane bagasse was employed to enhance the electrode's surface area and improve the dispersion of MnO2. The MnO2@cellulose modified poster-SPCE exhibited a high electrochemical response toward paraquat. Various influencing factors, including differential pulse voltammetric parameters and accumulation time, were systematically explored. Under the optimal conditions, the cathodic peak current was linearly proportional to paraquat concentration in a range of 2 to 200 µM, featuring a low detection limit of 1 µM. The proposed sensor offers cost-effectiveness and can be readily prepared via a simple procedure. Moreover, this method exhibits excellent reproducibility, high selectivity, and a short analysis time. The portable electrochemical sensor was able to determine paraquat in water samples with acceptable recoveries from 95.45 to 109.20%, indicating that the sensor based on MnO2@cellulose/SPCE is reliable for paraquat quantification. [ABSTRACT FROM AUTHOR]

Creatinine is one of the most important biomarkers to detect renal failures. The electrochemical detection of creatinine has been performed using complex enzymatic and non-enzymatic electrode arrays hindering their commercialization. In this work, a new and practical non-enzymatic electrochemical sensor was fabricated depositing copper on carbon paper electrodes by physical vapor deposition (namely Cu/CP). Surface and cross-sectional SEM images demonstrated the deposition of copper over the 3D structure of carbon paper. A thin film was found on the surface, while Cu nanowires with diameters of 180 ± 30 nm were found inside the 3D structure of CP. The thickness of the Cu film on the tubular structures of CP was of 390 ± 40 nm. High-resolution TEM images indicated that the Cu film was integrated by hierarchical structures containing terminal Cu hemispheres of 17.6 ± 2.2 nm. Additionally, interplanar distances from the selected-area electron diffraction pattern demonstrated the presence of Cu0, while Cu2O was also found. Creatinine concentrations in saliva between 16 and 400 µM indicate kidney failure. The Cu/CP electrochemical sensor detected creatinine with linear concentration ranges from 0 to 1000 µM with a r2 = 0.9936. Outstandingly, this sensor presented good reproducibility (RSD = 7.3%), and selectivity to detect creatinine in artificial saliva using interferents like urea, glucose, glycine, ascorbic and uric acids. [ABSTRACT FROM AUTHOR]

Using nanostructured materials issued from renewable resources could be the key to the development of good-quality low-cost products that help reduce pollution. Cellulose nanofibrils (CNFs) were obtained by alkaline and bleaching treatments of Amazonian Paricá hardwood sawdust, a waste material from the Brazilian forestry industry. This study evaluated a process consisting in alternating layers of Paricá CNFs and cassava starch to coat standard writing and printing (W&P) papers with a skim-coating method, in which one face of each paper sample is passed over the surface of a suspension containing either CNFs or cassava starch, alternatively. The coated samples were then compared to the uncoated paper in terms of mechanical and surface properties. The mechanical properties of the papers coated with alkaline CNFs showed a declining trend as the number of coating layers increased (from 47 to 31 MPa). The papers coated with starch layers showed improved mechanical performance compared to the samples only coated with alkaline and alkaline bleached CNFs. All the coated samples showed excellent resistance to water degradation. The worst degradation (4%) was observed for the samples coated with a single layer of alkaline CNFs. A significant improvement in surface wettability was observed when gelatinized cassava starch was applied to the paper samples, irrespective of the type of CNFs eventually present on the surface. All in all, these results suggest that using gelatinized cassava starch as an alternating layer between successive CNFs layers on the surface of W&P paper samples may be promising for improving their overall properties. [ABSTRACT FROM AUTHOR]

Microfluidic paper-based analytical devices often are combined with scanners as detectors. In this work, different scanning options offered by scanners: resolution, scanning mode, exposure to radiation, colour restoration, and saving format were tested. Moreover, different attempts to mathematical data treatment based on intensities of three channels—Red, Green and Blue, were studied. All measurements presented in this article were conducted for a model dye—bromothymol blue and a model analyte—zinc(II) ion (complexed with xylenol orange in a paper matrix). The article summarizes the scanning options and possibilities of mathematical calculations. Nevertheless, it is suggested that the best option is to use the prior prepared calculation file to paste obtained intensities and compare all presented in this article (and the most frequently used) equations to process intensities and decide which one should be used in the particular analysis. [ABSTRACT FROM AUTHOR]

The rapid discrimination of bacteria is currently an emerging trend in the fields of food safety, medical detection, and environmental observation. Traditional methods often require lengthy culturing processes, specialized analytical equipment, and bacterial recognition receptors. In response to this need, we have developed a paper-based fluorescence sensor array platform for identifying different bacteria. The sensor array is based on three unique carbon quantum dots (CQDs) as sensing units, each modified with a different antibiotic (polymyxin B, ampicillin, and gentamicin). These antibiotic-modified CQDs can aggregate on the bacterial surface, triggering aggregation-induced fluorescence quenching. The sensor array exhibits varying fluorescent responses to different bacterial species. To achieve low-cost and portable detection, CQDs were formulated into fluorescent ink and used with an inkjet printer to manufacture paper-based sensor arrays. A smartphone was used to collect the responses generated by the bacteria and platform. Diverse machine learning algorithms were utilized to discriminate bacterial types. Our findings showcase the platform's remarkable capability to differentiate among five bacterial strains, within a detection range spanning from 1.0 × 103 CFU/mL to 1.0 × 107 CFU/mL. Its practicality is further validated through the accurate identification of blind bacterial samples. With its cost-effectiveness, ease of fabrication, and high degree of integration, this platform holds significant promise for on-site detection of diverse bacteria. [ABSTRACT FROM AUTHOR]

The article discusses the potential of advanced technologies in the field of cultural heritage. It highlights how these technologies, such as virtual reality, artificial intelligence, and 3D printing, can be used to understand, preserve, and enhance cultural heritage. The article also presents scientific papers from the Florence Heri-Tech International Conference, showcasing the various applications of these technologies. The papers cover topics such as the use of hyperspectral imaging for hieroglyph recognition, the enhancement of user experience in cultural spaces through advanced systems, and the use of non-invasive techniques for conservation. Overall, the article emphasizes the significant impact of technology on the research, preservation, and promotion of cultural heritage. [Extracted from the article]

Renewable materials and material circularity are key priorities for the coming decades. While paper is the most utilized material in the packaging sector, its applications in food packaging are limited due to low barrier properties. Coating it with petroleum-based polymer barrier coatings renders it unrecyclable both mechanically and biologically. Bio-coated paper packaging, made from agricultural waste or by-products, presents environmentally favorable solutions that can benefit the biological cycle of the circular economy. The main objective of this study is to assess the applicability of grain and beer production by-products in wood pulp food packaging materials. It examines the effects of different grain by-products (industrial wheat grain processing residues and wheat bran) particles and concentrations (15 wt% and 40 wt%), as well as the impact of brewer's yeast (Saccharomyces cerevisiae) at a concentration of 10 wt%, on the physical–mechanical and barrier properties of Northern bleached softwood kraft (NBSK) and chemithermomechanical (CTMP) pulps. Material composites were fabricated using a standard sheet forming method. Physical–mechanical properties were analyzed through tensile strength, strain at break, tear resistance, and bending stiffness tests. Barrier-related properties were analyzed through roughness, air permeance, and water contact angle tests. Results revealed that the vast majority of physical–mechanical properties decreased with the increase of both types of grain production fillers. Industrial wheat grain processing residues had a lower impact on physical–mechanical properties than wheat bran filler. A higher percentage of property decrease was absorbed in NBSK pulp than in CTMP. Roughness of CTMP can be improved by adding both industrial wheat grain processing residues and wheat bran. Wheat bran particles can increase hydrophobicity. CTMP pulp strength properties can be increased with the addition of yeast; however, the yeast additive's effect on air permeance demonstrated a negative impact. In the case of NBSK pulp, which has higher primary strength properties, the addition of yeast does not make any significant changes. The conducted experiments demonstrated that, overall, the addition of these fillers resulted in a decline in physical–mechanical properties such as tensile strength, strain at break, tear resistance, and bending stiffness. This decline was more pronounced with higher concentrations of fillers. In the case of CTMP pulp, both types of fillers exhibited similar trends in affecting properties, whereas for NBSK pulp, wheat bran had a more significant impact compared to wheat grain processing residues. The addition of yeast generally led to a reduction in physical–mechanical properties, particularly in tensile strength and tear resistance. However, samples containing yeast displayed increased flexibility compared to controls. The influence on barrier properties varied: while yeast increased air permeability, it also enhanced surface hydrophobicity, thereby reducing the paper's receptivity to liquids. [ABSTRACT FROM AUTHOR]

The economic development of a country directly depends upon industries. But this economic development should not be at the cost of our natural environment. A substantial amount of water is spent during paper production, creating water scarcity and generating wastewater. Therefore, the Pollution Control Board classifies this industry into red category. Water is used in different papermaking stages such as debarking, pulping or bleaching, washing, and finishing. The wastewater thus generated contains lignin and xenobiotic compounds such as resin acids, chlorinated lignin, phenols, furans, dioxins, chlorophenols, adsorbable organic halogens (AOX), extractable organic halogens (EOCs), polychlorinated biphenyls, plasticizers, and polychlorinated dibenzodioxins. Nowadays, several microorganisms are used in the detoxification of these hazardous effluents. Researchers have found that microbial degradation is the most promising treatment method to remove high biological oxygen demand (BOD) and chemical oxygen demand (COD) from wastewater. Microorganisms also remove AOX toxicity, chlorinated compounds, suspended solids, color, lignin, derivatives, etc. from the pulp and paper mill effluents. But in the current scenario, mill effluents are known to deteriorate the environment and therefore it is highly desirable to deploy advanced technologies for effluent treatment. This review summarizes the eco-friendly advanced treatment technologies for effluents generated from pulp and paper mills. [ABSTRACT FROM AUTHOR]

Soot stain from diverse sources is the most common stain that stains historical paper documents found in libraries, museums, and storage facilities. It is believed to be one of the types of deterioration that arises from the contact between stains and paper sheets. Therefore, in the present work, the effectiveness of the synthesized hybrid nanogel consisting of carbopol and nanoparticles (NPs) of ZnO, TiO2, or Fe3O4, in low and high-viscosity forms, for eliminating soot stains from historical paper manuscripts was conducted. The prepared hybrid nanogels were characterized utilizing the TEM, AFM, XRD, DLS, and Zeta Potential techniques. Following preparation, the soot-stained paper samples were heated to 105 °C for 6 days, a process known as accelerated thermal aging. Surface morphology, mechanical properties and the color change of the paper samples were investigated. The prepared hybrid nanogel had a spherical shape with well-defined edges and uniform size, with an average particle diameter ranging from 30 to 35 nm. There was no significant NPs agglomeration seen, suggesting uniform dispersion in the carbopol matrix. Additionally, the prepared gels' crystal structure and phase purity were revealed by the XRD analysis results. Paper fibers were visible in some parts of the treated sample with TiO2/carbopol hybrid nanogel at high-viscosity before aging. Cleaning soot-stained paper samples using high-viscosity Fe3O4/carbopol hybrid nanogel is more successful than using low-viscosity nanogel. the sample treated with high-viscosity ZnONPs/carbopol hybrid nanogel produced the highest total color differences (ΔE) (26.17). The paper sample treated with high-viscosity ZnO/carbopol hybrid nanogel exhibited the maximum tensile strength (61.8 N/mm2) and elongation at break (1.174%). The evaluation of the paper samples both before and after the cleaning process revealed that, the treatment with high-viscosity ZnO/carbopol hybrid nanogel gave the best results in removing soot stains from stained paper samples. [ABSTRACT FROM AUTHOR]

Numerous natural dyes were used to dye mediaeval Islamic paper from the tenth to the nineteenth century, using a variety of techniques. The objective of this research is to develop an analytical method using high performance liquid chromatography with diode array detection (HPLC–DAD) to identify natural dyes in forty historical Islamic paper manuscripts from two collections. In addition, novel information was obtained from original treatises containing recipes for dyeing paper and the chronological use of dyes in dyeing mediaeval Islamic paper between the tenth and seventeenth centuries. The results show that thirty-four of the forty manuscripts examined contained dyes. Six natural dyes were detected, including henna, madder, lac, safflower, turmeric, and weld. This is the first study aimed at developing a method for determining various natural dyes in Islamic paper from a wide historical and geographical range in the mediaeval time and to fill significant gaps in the technical and historical knowledge of papermaking. [ABSTRACT FROM AUTHOR]

Anger suppression is important in our daily life, as its failure can sometimes lead to the breaking down of relationships in families. Thus, effective strategies to suppress or neutralise anger have been examined. This study shows that physical disposal of a piece of paper containing one's written thoughts on the cause of a provocative event neutralises anger, while holding the paper did not. In this study, participants wrote brief opinions about social problems and received a handwritten, insulting comment consisting of low evaluations about their composition from a confederate. Then, the participants wrote the cause and their thoughts about the provocative event. Half of the participants (disposal group) disposed of the paper in the trash can (Experiment 1) or in the shredder (Experiment 2), while the other half (retention group) kept it in a file on the desk. All the participants showed an increased subjective rating of anger after receiving the insulting feedback. However, the subjective anger for the disposal group decreased as low as the baseline period, while that of the retention group was still higher than that in the baseline period in both experiments. We propose this method as a powerful and simple way to eliminate anger. [ABSTRACT FROM AUTHOR]

We report an innovative and facile approach to fabricating an ultrasensitive plasmonic paper substrate for surface-enhanced Raman spectroscopy (SERS). The approach exploits the self-assembling capability of poly(styrene-b-2-vinyl pyridine) block copolymers to form a thin film at the air-liquid interface within the single microdroplet scale for the first time and the subsequent in situ growth of silver nanoparticles (AgNPs). The concentration of the block copolymer was found to play an essential role in stabilizing the droplets during the mass transfer phase and formation of silver nanoparticles, thus influencing the SERS signals. SEM analysis of the morphology of the plasmonic paper substrates revealed the formation of spherical AgNPs evenly distributed across the surface of the formed copolymer film with a size distribution of 47.5 nm. The resultant enhancement factor was calculated to be 1.2 × 107, and the detection limit of rhodamine 6G was as low as 48.9 pM. The nanohybridized plasmonic paper was successfully applied to detect two emerging pollutants—sildenafil and flibanserin—with LODs as low as 1.48 nM and 3.45 nM, respectively. Thus, this study offers new prospects for designing an affordable and readily available, yet highly sensitive, paper-based SERS substrate with the potential for development as a lab-on-a-chip device. [ABSTRACT FROM AUTHOR]

Uric acid (UA) is an important biomarker, as a high concentration in blood can lead to gout and further renal syndrome. Although several point-of-care testing (POCT) devices have been reported to detect UA, there are some limitations such as the requirement for uricase and the complicated pretreatment of serum/plasma samples, which restricts their use at home or in undeveloped areas. In this work, we developed an approach by applying Zn2+ to precipitate proteins and cells in whole blood to avoid interference with the chromogenic reaction. We used carboxymethylcellulose (CMC) to immobilize tetramethylbenzidine (TMB) on a nitrocellulose membrane for colorimetric detection. Using the oxidization properties of H2O2, which turns TMB into oxidized tetramethylbenzidine (TMBox) in the presence of catalyst gold nanoparticles (AuNPs), we successfully constructed an enzyme-free paper-based POCT device using the reduction reaction of UA and TMBox for simple, speedy, and cheap colorimetric detection of UA, achieving a detection time of 8 min, a linear range of 0–150 μg/mL, and an LOD of 25.79 μg/mL. The UA concentration in whole blood samples was further measured and correlated well with the clinical value (R2 = 0.8212). Thus, the proposed assay has the potential for POCT diagnosis, monitoring, and prognosis of diseases related to UA. By applying Zn2+ reagent to precipitate proteins and cells in whole blood and the reduction reaction of UA, an enzyme-free paper-based POCT assay was established. [ABSTRACT FROM AUTHOR]

Despite progress in the prevention and diagnosis of cancer, current technologies for tumor detection present several limitations including invasiveness, toxicity, inaccuracy, lengthy testing duration and high cost. Therefore, innovative diagnostic techniques that integrate knowledge from biology, oncology, medicinal and analytical chemistry are now quickly emerging in the attempt to address these issues. Following this approach, here we developed a paper-based electrochemical device for detecting cancer-derived Small Extracellular Vesicles (S-EVs) in fluids. S-EVs were obtained from cancer cell lines known to express, at a different level, the αvβ6 integrin receptor, a well-established hallmark of numerous epithelial cancer types. The resulting biosensor turned out to recognize αvβ6-containing S-EVs down to a limit of 0.7*103 S-EVs/mL with a linear range up to 105 S-EVs /mL, and a relative standard deviation of 11%, thus it may represent a novel opportunity for αvβ6 expressing cancers detection. The detection of cancer in its early stages can greatly prevent disease development, however, current technologies for tumor detection present several limitations. Here, the authors develop a paper-based electrochemical device for detecting cancer-derived small extracellular vesicles (S-EVs) in fluids, recognizing αvβ6-containing S-EVs down to a limit of 0.7*103 S-EVs/mL with a linear range up to 105 S-EVs/mL. [ABSTRACT FROM AUTHOR]

The pulp and paper industry is an important contributor to global greenhouse gas emissions1,2. Country-specific strategies are essential for the industry to achieve net-zero emissions by 2050, given its vast heterogeneities across countries3,4. Here we develop a comprehensive bottom-up assessment of net greenhouse gas emissions of the domestic paper-related sectors for 30 major countries from 1961 to 2019—about 3.2% of global anthropogenic greenhouse gas emissions from the same period5—and explore mitigation strategies through 2,160 scenarios covering key factors. Our results show substantial differences across countries in terms of historical emissions evolution trends and structure. All countries can achieve net-zero emissions for their pulp and paper industry by 2050, with a single measure for most developed countries and several measures for most developing countries. Except for energy-efficiency improvement and energy-system decarbonization, tropical developing countries with abundant forest resources should give priority to sustainable forest management, whereas other developing countries should pay more attention to enhancing methane capture rate and reducing recycling. These insights are crucial for developing net-zero strategies tailored to each country and achieving net-zero emissions by 2050 for the pulp and paper industry.A bottom-up assessment of the net greenhouse gas emissions of the pulp and paper industries of 30 countries from 1961 to 2019 leads to country-specific strategies to achieve net zero by 2050. [ABSTRACT FROM AUTHOR]

The effective utilization for recycled carbon fibers (rCFs) is significant for less pollution, low energy consumption and resource conservation. This paper proposed a path for reprocessing the recycled carbon fibers into CF/PA6 fiber papers using flexible papermaking technology. Then, the CF/PA6 fiber paper could be used as an interlayer component to continuous CF woven/epoxy resin composites to form hybrid composites. The configurations of hybrid composites and directions of papers effects on notched impact resistance and flexural performance were systematically discussed. The micro energy absorption mechanism was revealed based on real-time crack tracking. The results indicate that cracks migration between woven and paper contributes to impact and flexural energy absorption, most improving 22.64% and 40.85% respectively in one-layer paper with longitudinal direction in the middle location (L1). Whereas, there is a negative effect of hybrid composites on flexural strength and modulus compared with pure CF woven composites. The behaviors of hybrid composites with longitudinal direction of paper are greater than that with transverse direction on stress, modulus, and the absorbed energy in the same configurations. Furthermore, spatial flexural morphologies are also affected by damage path. The final failure modes integrate the continuous woven fabric composite and discontinuous CF/PA6 fiber paper composite, mainly including fiber and matrix fracture, fiber pull-out and delamination. It provides a guidance for material design and structural optimization in reusing of carbon fibers. [ABSTRACT FROM AUTHOR]

Using glass as a structural element that could obtain the role of the primary load-bearing elements of iconoclast structures has had a superficial history. Because of its aesthetic and admissible mechanical properties, glass has been considered one of the structural elements in the construction industry. Because of its extrasafety, laminated glass on top of the most widely used elements has been appraised with more depth. The study aimed to evaluate the failure modes in laminated glass and the possibility of detecting the pre-failure status of the surveyed elements, referring to the proffered approaches and image processing (IP) procedures in the literature. The outcomes have compared the peculiarity and strength points of various routes and have reached the inference for proper approaches in every procedure. According to the results, image processing (IP) is the most appropriate method of pre-failure detection in load-bearing laminated glass elements. Among the image processing (IP) techniques, digital image correlation has the widest application. The results of this study, in combination with other pieces of research, may propound a database for evaluating the failure status of glass structures. [ABSTRACT FROM AUTHOR]

Adverse Outcome Pathways (AOPs) have been proposed to facilitate mechanistic understanding of interactions of chemicals/materials with biological systems. Each AOP starts with a molecular initiating event (MIE) and possibly ends with adverse outcome(s) (AOs) via a series of key events (KEs). So far, the interaction of engineered nanomaterials (ENMs) with biomolecules, biomembranes, cells, and biological structures, in general, is not yet fully elucidated. There is also a huge lack of information on which AOPs are ENMs-relevant or -specific, despite numerous published data on toxicological endpoints they trigger, such as oxidative stress and inflammation. We propose to integrate related data and knowledge recently collected. Our approach combines the annotation of nanomaterials and their MIEs with ontology annotation to demonstrate how we can then query AOPs and biological pathway information for these materials. We conclude that a FAIR (Findable, Accessible, Interoperable, Reusable) representation of the ENM-MIE knowledge simplifies integration with other knowledge. Scientific contribution: This study introduces a new database linking nanomaterial stressors to the first known MIE or KE. Second, it presents a reproducible workflow to analyze and summarize this knowledge. Third, this work extends the use of semantic web technologies to the field of nanoinformatics and nanosafety. [ABSTRACT FROM AUTHOR]

As the social organism, Polistes wasps build a communal nest using woody fibers with saliva for sustaining brood and adult population throughout the season. Limited information exists regarding the identification specific plant materials employed in wasp nest building. Thus, we firstly tested if the DNA metabarcoding approach utilizing rbcL and trnL molecular markers could identify the plant species quantitatively and qualitatively inform the mixed-origin woody samples. A threshold of 0.01 proportion of reads was applied for rbcL and trnL molecular markers, while this threshold for median proportion was 0.0025. In assessing taxa richness, the median proportion demonstrated superior performance, exhibiting higher taxa detection power, however, rbcL marker outperformed in quantitative analysis. Subsequently, we applied DNA metabarcoding to identify the plant materials from the nests of two Polistes species, P. mandarinus and P. rothneyi. The results showed that higher preference of Quercus and Robinia as the major nest building materials regardless of the surrounding plant communities, by two wasp species. Material diversity was higher for P. rothneyi than P. mandarinus, which may explain the abundance of this species possibly with heightened adaptive capacities in their nesting behavior. This study demonstrated that DNA metabarcoding could identify the complex nest-building plant materials of paper wasps and provide insights into their ecological interactions in the natural ecosystem. [ABSTRACT FROM AUTHOR]

In this work, a low-cost and eco-friendly paper-based analytical device (PAD) method is described for the determination of phyto-cannabinoids in cannabis and oral fluids based on a simple colorimetric reaction. The PAD was able to distinguish tetrahydrocannabinol (THC)- and cannabidiol (CBD)-rich plant samples by using 4-aminophenol (4-AP) and later on to quantify total phyto-cannabinoid content (THC + CBD + CBN) in plant and oral fluids by using the Fast Corinth V reagent. The chemical and physical properties regarding paper type and reagent concentration in the PAD were optimized to achieve the best analytical performance. After that, analytical features were obtained, including a linear range of 0.01–0.1 mg mL−1, a limit of detection (LOD) of 0.003 mg mL−1, and a suitable precision, expressed as relative standard deviation (RSD) lower than 10%. Furthermore, no significant interferences were observed in colorimetric reactions when tea, herbs, and drug samples were analyzed. Additionally, the PAD proved color stability up to 1 month after the sampling at 25 °C. The developed PAD was suitable for determining total phyto-cannabinoid content in plants and oral fluids, obtaining good results compared to GC–MS. Overall, this method showed good reliability resulting in an operational on-site device for drug monitoring. [ABSTRACT FROM AUTHOR]

Unreliable data, falsification and other issues related to misconduct are driving a growing proportion of retractions. [ABSTRACT FROM AUTHOR]

Energy storage devices (ESD) which are intended to power electronic devices, used in close contact of human skin, are desirable to be safe and non-toxic. In light of this requirement, Zn based energy storage devices seem to provide a viable pathway as they mostly employ aqueous based electrolytes which are safe and non-toxic in their functioning. Additionally, having a flexible ESD will play a crucial role as it will enable the ESD to conform to the varying shapes and sizes of wearable electronics which they energize. In this work, we have developed an inkjet-printed Zinc ion battery (IPZIB) with planar electrode configuration over bond paper substrate. Zn has been used as the negative electrode, MnO2 is used as the positive electrode with Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) as the active binder. Conducting tracks of reduced graphene oxide (rGO) are used to construct the current collector on the paper substrate. The fabricated IPZIB delivered a high discharge capacity of 300.14 mAh g−1 at a current density of 200 mA g−1. The energy density of the IPZIB is observed as 330.15 Wh kg−1 at a power density of 220 W kg−1 and retains an energy density of 94.36 Wh kg−1 at a high power density of 1650 W kg−1. Finally, we have demonstrated the capability of the IPZIB to power a LED at various bending and folding conditions which indicates its potential to be used in the next generation flexible and wearable electronic devices. [ABSTRACT FROM AUTHOR]

To stimulate the development and application of formal methods in industry, we need to promote research and development for the improvement of formal methods and tools for industrial applications, and we need to exchange experiences of the industrial usage of these methods and tools. This special issue of Software Tools for Technology Transfer presents various tools and experience reports that are targeting the use of formal methods in industry. The papers in this special issue are extended versions of selected conference papers from the proceedings of the 27th International Conference on Formal Methods for Industrial Critical Systems (FMICS 2022). [ABSTRACT FROM AUTHOR]

Autistic individuals often experience a wide range of barriers and challenges with employment across their lifetime. Despite their strengths and abilities to contribute to the workforce, many individuals experience unemployment, underemployment and malemployment. However, current supports and services are often inadequate to meet their needs. To allow autistic people to achieve vocational success, we explore four contributors to employment and expand upon the issues and potential solutions to each. These positions include the importance of family support and its consideration in the application of vocational support interventions, addressing transitional needs for autistic youth, building employer capacity, and conducting research that advises the development of meaningful programs and policies. By advocating for these positions, we aim to foster greater inclusivity and support for individuals with ASD in the workplace. [ABSTRACT FROM AUTHOR]

Background: Nuclear medicine has made enormous progress in the past decades. However, there are still significant inequalities in patient access among different countries, which could be mitigated by improving access to and availability of radiopharmaceuticals. Main body: This paper summarises major considerations for a suitable pharmaceutical regulatory framework to facilitate patient access to radiopharmaceuticals. These include the distinct characteristics of radiopharmaceuticals which require dedicated regulations, considering the impact of the variable complexity of radiopharmaceutical preparation, personnel requirements, manufacturing practices and quality assurance, regulatory authority interfaces, communication and training, as well as marketing authorisation procedures to ensure availability of radiopharmaceuticals. Finally, domestic and regional supply to ensure patient access via alternative regulatory pathways, including in-house production of radiopharmaceuticals, is described, and an outlook on regulatory challenges faced by new developments, such as the use of alpha emitters, is provided. Conclusions: All these considerations are an outcome of a dedicated Technical Meeting organised by the IAEA in 2023 and represent the views and opinions of experts in the field, not those of any regulatory authorities. [ABSTRACT FROM AUTHOR]

Substantial R &D efforts are currently directed towards the development of combined heat and power (CHP) systems that automatically and seamlessly connect to the power grid. In this paper we develop a real options model to assess the impact that the operational flexibility characterizing such systems will have on the optimal timing and capacity associated with investments in CHP plants. We take the viewpoint of a manufacturer operating in an energy-intensive industry who contemplates investing in CHP. We discuss and compare investments in two types of CHP systems: a standard one that is operationally rigid and a technologically advanced one that is operationally flexible. The interaction between temporal and operational flexibility under uncertainty and irreversibility is central to our analysis. We show that operational flexibility guarantees earlier investment but has an ambiguous effect in terms of capacity. In particular, when operational flexibility is very valuable the potential investor is opting for investing in a plant with larger productive capacity. The potential investor chooses a smaller CHP unit if otherwise. A numerical exercise calibrated using data from the Italian pulp and paper and electricity industries complements our theoretical analysis. [ABSTRACT FROM AUTHOR]

EXCLUSIVE: Poor-quality studies are polluting the literature — a group will study the businesses that produce them to stem the flow of bogus research. [ABSTRACT FROM AUTHOR]

To achieve integrated resource utilization of graphite tailings to improve their water-holding capacity, river silt and cow dung powder were added to graphite tailings as organic matter improvers. Improver ratios were designed using 4 g cow dung powder and 20, 30, and 50 g river silt. Soil–water characterization tests were performed using a combined tensiometer and filter paper method based on optimum density measurements. Analysis of the influence of river silt dosing on the soil–water characteristic curves of improved graphite tailing specimens was performed with data fitting using the Van Genuchten model. Here, we investigated the effect of river silt dosing on the internal pore structure and water-holding capacity of modified graphite tailing samples and verified the applicability of the model to graphite tailings. Our results demonstrate that the organic matter improver incorporated into graphite tailings can improve the internal structural compactness of graphite tailings, improving the water holding capacity. With an increase in river silt dosage, the saturated water content is larger, and the residual water content increases and then decreases. When river silt dosage is 30 g, the residual water content is the highest at a value of 3.32%. The van Genuchten model was highly accurate for assessing the graphite tailings. With an increase in river silt doping, the internal pore space first decreased and then increased, and the internal structure gradually became compact and loosened. The internal structure was in the optimal state in the experimental study when the dosage of cow dung powder was 4 g and the dosage of river silt was 30 g. The water holding capacity was optimal at this time. The results of this study provide a theoretical foundation for graphite-tailing-based mine reclamation and play a guiding role in exploring the value of the hydraulic characteristic index parameters when applying graphite tailings engineering. [ABSTRACT FROM AUTHOR]

Herein, we report on conductive ultrathin films (nanosheets) with the characteristics of stretchability and water vapor permeability for skin-conformable bioelectrodes. The films are fabricated by combining conductive fibrous networks of single-wall carbon nanotubes (SWCNTs) and poly(styrene-b-butadiene-b-styrene) (SBS) nanosheets (i.e., SWCNT-SBS nanosheets). An increase in the number of SWCNT coatings increases both the thicknesses and densities of the SWCNT bundles. The SBS nanosheets coated with three layers of SWCNTs (i.e., SWCNT 3rd-SBS nanosheets) show comparable sheet resistance to the SBS nanosheets coated with poly(3,4-ethylenedioxithiophene) doped with poly(4-styrenesulfonate acid) (PEDOT:PSS) containing 5 wt.% butylene glycol (i.e., PEDOT:PSS/BG5-SBS nanosheets). In addition, the SWCNT 3rd-SBS nanosheets exhibit significantly reduced elastic moduli and increased elongations at break compared to the PEDOT:PSS/BG5-SBS nanosheets. Furthermore, the calculated water vapor transmission ratio of the 210-nm-thick SBS nanosheets (268,172 g m−2 (2 h)−1) is greater than that of the filter paper (6345 g m−2 (2 h)−1). The SWCNT 3rd-SBS nanosheets attached to model skin show high tolerances to bending and artificial sweat at different pH values (i.e., the electrical resistance changes ~1.1 times). Finally, the SWCNT 3rd-SBS nanosheet is applied to detect the surface electromyogram from the forearm of a subject. This nanosheet displays a signal-to-noise ratio similar to that of the PEDOT:PSS/BG5-SBS nanosheet. We report on conductive ultrathin films (referred to as "nanosheets") with stretchability and water vapor permeability for skin-conformable bioelectrodes. By combining conductive fibrous networks of single-wall carbon nanotubes and poly(styrene-b-butadiene-b-styrene) continuous nanosheets (i.e., SWCNT-SBS nanosheets), the conductive nanosheet shows a high tolerance to bending on a model skin sheet and a high permeability to humidity. Finally, we demonstrate that the conductive nanosheet can detect the surface electromyogram signals from a subject's forearm. [ABSTRACT FROM AUTHOR]

The redox additive KI-modified and H2SO4-protonated polyvinyl alcohol gel polymer electrolyte (KI-H2SO4-PVA GPE) is used to match well with an activated carbon paper (ACP) electrode, which is adopted for solid-state pseudocapacitor applications. Enhanced hydrogen bonding interactions are established between oxygen-containing functional groups of ACP and multi-hydroxyl groups of PVA, promoting interfacial charge transfer. An intensified electrostatic adsorption is also promoted between H2SO4-protonated PVA and free iodide anions, enhancing the ionic and electrical conductivity of GPE. The electroactive iodide anion with polyvalent states of I−, I3− and IO3− in KI-H2SO4-PVA GPE participates in reversible redox reactions at the ACP electrode interface, which mostly contributes to Faradaic capacitance. The mass ratio of redox additive KI was optimized to be 0.166, which could balance the capacitance and the cyclability of KI-H2SO4-PVA GPE. The KI-H2SO4-PVA GPE reveals lower ohm resistance, charge transfer resistance and Warburg impedance, leading to its higher electrical and ion conductivity compared to H2SO4-PVA GPE. Theoretical simulations proved that the protonation of H2SO4-PVA and electrostatic interaction between H2SO4-protonated PVA and KI could cause an effective decrease in the interfacial energy of the activated carbon paper electrode. The KI-H2SO4-PVA GPE/ACP accordingly presents higher specific capacitance (24.75 mF cm−2) and rate capability (45.5%) than H2SO4-PVA GPE/ACP (12.93 mF cm−2, 15.6%). The redox-activated KI-H2SO4-PVA GPE exhibits a lowered cycling stability (64.5%) compared to H2SO4-PVA GPE (78.3%) in ACP supercapacitor applications due to the gradually decreasing irreversibility of the redox reactions of polyvalent iodide ions. The KI-H2SO4-PVA GPE matches well with ACP electrode and accordingly is suitable for solid-state pseudocapacitor applications with high capacitance performance. The KI-modified and H2SO4-protonated polyvinyl alcohol gel polymer electrolyte (KI-H2SO4-PVA GPE) is used to match well with the hydroxyl and epoxy groups activated carbon paper (ACP) electrode to form the intensified hydrogen bonding interface, contributing to superior Faradaic capacitance for the solid-state supercapacitor application. [ABSTRACT FROM AUTHOR]

For shaped charge blasting projects in mining, civil engineering, and similar fields, it is proposed to modify the charge structure by combining slotted tubes and shaped charge liners to obtain a new type of charge structure. This aims to achieve directional rock breaking through the focused action of the shaped charge. The influence of different slotted pipe materials on the directional rock-breaking effect of concentrated energy using a new charge structure is explored through theoretical analysis combined with model test study, high-speed camera, stress–strain gauge, and other equipment. A comparison is made between slotted pipes made of aluminum, kraft paper, and PVC, with the cutting width of 2 mm. Based on the characteristics of the cracks formed after blasting, the new charge structure made of aluminum slotted pipe produces a penetrating crack that is almost consistent with the pre-cracking direction. Based on the corresponding characteristics of successively released blasting energy, the guiding and convergence effect of the new charge structure made of aluminum slotted pipe on the explosion energy is greater than that of the new charge structure made of the other two types of slotted pipe material. According to the strain data measured after blasting, the peak arrival time of the strain peak in the direction of the slotted pipe on one side of the shaped hood is shorter than that in the other two directions, and the peak strain is greater than that in the other two directions while having a better energy gathering effect. Based on the findings, the new charge structure with directional energy concentration has a damage reduction effect. Furthermore, the material of aluminum slotted pipe is found to be better than PVC slotted pipe, whereas the material of PVC slotted pipe is better than kraft paper slotted pipe in achieving directional rock breaking. [ABSTRACT FROM AUTHOR]

While gamified technology integration in vocabulary instruction within a flipped classroom has yielded beneficial teaching outcomes, specific studies have raised concerns about potential adverse effects linked to this approach. As a result, conducting a comparative analysis between gamified technology and conventional paper-based methods within the flipped classroom framework has become essential. This analysis aims to foster the development of a targeted teaching approach that adeptly addresses the unique needs of students. This study employed a sequential explanatory research design to examine the effectiveness of flipped classroom with gamified technology and paper-based method in teaching vocabulary to students with different proficiency levels. Quantitative data was gathered from a pretest and a posttest, whilst qualitative data was collected through teachers' guided reflection. Using Academic Word List (300 target words), control groups employed a paper-based, while experimental groups applied gamified technology (Quizlet, Kahoot!, Quizizz, Socrative, and Google Form), which lasted 10 weeks. The participants were 144 non-English major students who took a general English course in the 2nd semester of 2023. Quantitative data analysis ran in SPSS 25 using Paired Sample t-Test and One-way ANOVA. The qualitative data were analyzed using thematic progression. The results showed that gamified technology did not affect students' learning outcomes, while the paper-based method resulted conversely. It revealed that the paper-based method is more effective than gamified technology for students in general, with low proficiency and high-proficiency level. Further, teachers' beliefs admitted distinctive issues that gamified technology was more effective for high-proficiency learners, whereas paper-based was more effective for low-proficiency learners. The difference analysis of quantitative and qualitative data sheds light on discussing threats while implementing gamified technology and possible solutions. [ABSTRACT FROM AUTHOR]

Large language models (LLMs) are an exciting breakthrough in the rapidly growing field of artificial intelligence (AI), offering unparalleled potential in a variety of application domains such as finance, business, healthcare, cybersecurity, and so on. However, concerns regarding their trustworthiness and ethical implications have become increasingly prominent as these models are considered black-box and continue to progress. This position paper explores the potentiality of LLM from diverse perspectives as well as the associated risk factors with awareness. Towards this, we highlight not only the technical challenges but also the ethical implications and societal impacts associated with LLM deployment emphasizing fairness, transparency, explainability, trust and accountability. We conclude this paper by summarizing potential research scopes with direction. Overall, the purpose of this position paper is to contribute to the ongoing discussion of LLM potentiality and awareness from the perspective of trustworthiness and responsibility in AI. [ABSTRACT FROM AUTHOR]

Browser plug-in alerts users when studies — or their references — have been posted on a site known for raising integrity concerns. [ABSTRACT FROM AUTHOR]

The knowledge graph based on research papers can accurately identify and present the latest developments in scientific and technological (S&T) innovation and is of great significance for supporting strategic decision-making relating to S&T innovation in undeveloped areas. Based on the international research papers produced in Gansu Province during the 13th Five-Year Plan period (2016–2020), five metrics, including the number and characteristics of papers, co-authors, main publications and their fields, major supporting institutions, and main research areas, are established herein. The results indicate that: (i) the total of 29,951 papers were published, which is about 2.89 times that in 2010–2015; (ii) Gansu Province collaborated with 149 countries/regions globally; (iii) the top 5 journals in terms of the number of papers were Medicine, Scientific Reports, RSC Advances, Science of the Total Environment, and Physical Reviews D; (iv) the funding sources were mainly from the national level; and (5) the top 5 research areas were chemistry, engineering, physics, material science, environmental science, and ecology, which accounted for 64.7% of all papers. Finally, the present study puts forward some recommendations for the decision-making process in the strategic layout of S&T innovation in Gansu Province. [ABSTRACT FROM AUTHOR]

Exosomes as new biomarkers for cancer diagnosis have attracted attention because they are highly released by tumor cells in various biological fluids. In this study, an electrochemical paper-based immunosensor device (Exo-sensing paper) is introduced for the detection of exosome in the serum. The Exo-sensing paper is a three-electrode system that is prepared using pattern paper and carbon and silver inks. The sensor part of this immunosensor contains a three-dimensional porous nanocomposite of nickel nanofoam coupled with graphene oxide and gold nanoparticles. The high specific surface area of this nanocomposite increases the antibody loading on the sensor surface significantly and consequently leads to obtaining a wide linear range of 500–1 × 107 Exospore µL−1 with a detection limit of 110 Exosome µL−1. Due to some advantages of this constructed Exo-sensing paper such as easy storage, simple application, low cost and good selectivity in the real samples, this system has a good potential to be used as a point of care testing for in situ detection of the exosomes and is a promising strategy for minimally invasive liquid biopsy.Graphical abstract: Exosomes as new biomarkers for cancer diagnosis have attracted attention because they are highly released by tumor cells in various biological fluids. In this study, an electrochemical paper-based immunosensor device (Exo-sensing paper) is introduced for the detection of exosome in the serum. The Exo-sensing paper is a three-electrode system that is prepared using pattern paper and carbon and silver inks. The sensor part of this immunosensor contains a three-dimensional porous nanocomposite of nickel nanofoam coupled with graphene oxide and gold nanoparticles. The high specific surface area of this nanocomposite increases the antibody loading on the sensor surface significantly and consequently leads to obtaining a wide linear range of 500–1 × 107 Exospore µL−1 with a detection limit of 110 Exosome µL−1. Due to some advantages of this constructed Exo-sensing paper such as easy storage, simple application, low cost and good selectivity in the real samples, this system has a good potential to be used as a point of care testing for in situ detection of the exosomes and is a promising strategy for minimally invasive liquid biopsy. [ABSTRACT FROM AUTHOR]

Metagenomics has revolutionized access to genomic information of microorganisms inhabiting the gut of herbivorous animals, circumventing the need for their isolation and cultivation. Exploring these microorganisms for novel hydrolytic enzymes becomes unattainable without utilizing metagenome sequencing. In this study, we harnessed a suite of bioinformatic analyses to discover a novel cellulase-degrading enzyme from the camel rumen metagenome. Among the protein-coding sequences containing cellulase-encoding domains, we identified and subsequently cloned and purified a promising candidate cellulase enzyme, Celcm05-2, to a state of homogeneity. The enzyme belonged to GH5 subfamily 4 and exhibited robust enzymatic activity under acidic pH conditions. It maintained hydrolytic activity under various environmental conditions, including the presence of metal ions, non-ionic surfactant Triton X-100, organic solvents, and varying temperatures. With an optimal temperature of 40 °C, Celcm05-2 showcased remarkable efficiency when deployed on crystalline cellulose (> 3.6 IU/mL), specifically Avicel, thereby positioning it as an attractive candidate for a myriad of biotechnological applications spanning biofuel production, paper and pulp processing, and textile manufacturing. Efficient biodegradation of waste paper pulp residues and the evidence of biopolishing suggested that Celcm05-2 can be used in the bioprocessing of cellulosic craft fabrics in the textile industry. Our findings suggest that the camel rumen microbiome can be mined for novel cellulase enzymes that can find potential applications across diverse biotechnological processes. [ABSTRACT FROM AUTHOR]

This study aims to highlight the current trends in the literature on sustainability by applying a bibliometric review of papers on sustainability published in Environment, Development and Sustainability. Bibliometric analysis is a quantitative approach to bibliographic materials that highlights the core theoretical and empirical research on a specific field. In addition, it allows the classification of previous studies. Previous bibliometric reviewers were limited to sustainability papers in specific industries, while this study considers all papers on sustainability to provide further insights on overall sustainability topics. The analysis was based on keyword cartography analysis, bibliometric authors' citation analysis, bibliometric papers' citation analysis, bibliometric references' co-citation analysis, journals' co-citation cartography, and qualitative content analysis. A total of 997 articles on sustainability were reviewed. Bibliometric analysis was performed using VOSviewer and content analysis was performed using WordStat. Six major clusters were identified: environmental sustainability, sustainable development, urban sustainability, ecological footprint, environment, and climate change. In addition, the results reveal that Environment, Development and Sustainability has increasingly experienced important growth in research papers and citations, reflecting its significant contribution to the sustainability research field. In addition, this study presents recommendations for future research opportunities in the field of sustainability. The findings of this study have implications for sustainability research, such as the assessment of environmental and social sustainability in multinational institutional contexts and across industries as well as the examination of the impact of environmental and social sustainability on different corporate aspects and decisions. This study is the only one to review the key topics on which papers published in Environment, Development and Sustainability are focused and can be largely used for sustainability practices. This study provides an overview of how the literature on sustainability has developed, as well as a summary of the most productive authors, along with countries, organizations, and journal sources. This offers an opportunity for future research to focus on this topic. [ABSTRACT FROM AUTHOR]