Search

Purpose: The purpose of this study is to investigate the effects of a pigment coating on the mechanical properties of fluting paper. Design/methodology/approach: Two different calcium carbonate pigments were used in the preparation of the coated color, precipitated calcium carbonate (PCC) and ground calcium carbonate (GCC). Fluting paper produced by recycling waste paper was used as base paper. The effects of PCC and GCC pigments on mechanical properties were compared. Ring crush test (RCT), corrugating medium test (CMT), corrugating crush test (CCT), tensile and burst strength tests were applied to the coated papers, and the results were compared to the mechanical properties of base paper. Findings: The tensile and burst indices of the coated papers were found to be higher than base papers about 13.9% and 6.05%, respectively. While the coating process positively affected the RCT and CCT values, it did not show a significant impact on the CMT values. GCC, one of the pigments used in coating colors, had a more effective effect on the mechanical properties of fluting papers compared to PCC. Originality/value: These results suggest that coating of fluting papers has a positive effect on mechanical properties and the use of GCC as a pigment is more effective than PCC. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to study the application of high-tolerance and flexible indigenous bacteria and fungi, along with the co-metabolism in recycled paper and cardboard mill (RPCM) wastewater treatment (WWT). Design/methodology/approach: The molecular characterization of isolated indigenous bacteria and fungi was performed by 16S rRNA and 18S rRNA gene sequencing, respectively. Glucose was used as a cometabolic substrate to enhance the bioremediation process. Findings: The highest removal efficiency was achieved for both chemical oxygen demand (COD) and color [78% COD and 45% color removal by Pseudomonas aeruginosa RW-2 (MZ603673), as well as approximately 70% COD and 48% color removal by Geotrichum candidum RW-4 (ON024394)]. The corresponding percentages were higher in comparison with the efficiency obtained from the oxidation ditch unit in the full-scale RPCM WWT plant. Originality/value: Indigenous P. aeruginosa RW-2 and G. candidum RW-4 demonstrated effective capability in RPCM WWT despite the highly toxic and low biodegradable nature, especially with the assistance of glucose. [ABSTRACT FROM AUTHOR]

Purpose: This study aims to determine the ink removal efficiency of papers with different recycling numbers and to examine some electrophotographic printing properties. Design/methodology/approach: The base papers prepared according to the INGEDE 11p standard are subjected to six recycling stages (RS) under equal conditions. The physical-optical properties of the papers obtained at the end of each RS are measured and CMYK (cyan, magenta, yellow, key) color measurement scales are printed on each paper with electrophotographic printing. Color measurements of the printed papers are measured using the X-Rite eXact spectrophotometer, adhering to the ISO 13655:2017 standard. According to the measurement results of the optical properties, the ink removal efficiency of each recycling step is determined as a percentage (%) using some formulas. Findings: As general, according to DEMLab and IERIC data, it is determined that the ink removal efficiency increased as the recycling repetition increased. In DEMf factor values, the highest deinking efficiency is obtained after the fourth RS. There is no significant difference between the printing properties of the samples. Originality/value: It has been a matter of curiosity that papers lose their properties after how many RS. Many studies have been carried out on this subject and it has been presented by experimental methods that the printability properties of papers increase or decrease after which RS. This study can be a pioneer for future studies. [ABSTRACT FROM AUTHOR]

Purpose: Paper aims to evaluate the efficiency of traditional chitosan, nano chitosan, and chitosan nanocomposites for consolidating aged papyrus samples. Cellulose-based materials, such as papyrus sheets and paper, which are the most common types of writing supports for works of art in many museums and archive. They are subjected to different types of deterioration factors that may lead to many conservation problems. Consolidation treatment is one of the most common conservation treatments, which should have perform after much testing to select the appropriate consolidants. Design/methodology/approach: This research paper aims to evaluate the resistance of traditional chitosan, nanochitosan and chitosan/zinc oxide nanocomposite as an eco-friendly papyrus strengthening. Untreated and treated papyrus was thermally aged and characterized via scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). Antimicrobial activity of the papyrus specimens was also determined against four tested pathogenic bacteria by disc diffusion method: MRSA, Staphylococcus aureus, E. coli and P. aeruginosa. Findings: The results revealed that chitosan nanocomposite showed a remarkable enhancement of papyrus tensile properties and presence of ZnO prevents the effects of biodeterioration. Originality/value: Zinc oxide nanoparticles enhance the optical properties and increase the chemical reactions between the consolidating material and the treated papyrus. [ABSTRACT FROM AUTHOR]

Purpose: The main aim of this study is to study the effect of alkyl dimethyl benzyl ammonium chloride on removing stains, yellowness and harmful metal ions on historical printed paper, as well as the effect of this cleaner on optical and chemical properties of treated paper. Design/methodology/approach: The assessments after and before treatment were carried out using digital microscopy, infrared spectroscopy (FTIR), pH measurement, color change and finally scanning electron microscopy. Findings: The results showed that the concentrations used under study (1% and 3%) cleaned the paper efficiently without any observed effect on the chemical composition of cellulose, which was confirmed by IR spectra. The most stains that completely disappeared were the soil spots, also the pH values had improved significantly after treatment, which confirms that the detergent is effective in neutralizing the acidity of cellulose. Moreover, the color change revealed an increase in the chromatic lightness of the paper after treatment, which agreed with the results of the scanning electron microscopy examination, as the paper appeared free of dirt, and the fibers and bundles became more cohesive. Originality/value: To the best of the authors' knowledge, this study is a unique study, as there is no previous literature that has indicated the use of the effect of alkyl dimethyl benzyl ammonium chloride washing treatments for printed historical paper, as it was limited only to making disinfection materials and water purification products. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to provide a deeper understanding of using filling materials that are used to fill gaps in wooden objects, and their response to changes in the surrounding environment to evaluate wood gap fillers and choose the best material. As a wide variety of materials, but most of them were unsuitable for filler mixtures. Specific materials were used, which can adapt to changes in wood size in response to changes in humidity. This research discusses the results of experiments that were conducted to determine how gap fillers composed of glass microballoons, microcrystalline cellulose and paper pulp fills are mixed with Klucel G, Paraloid B-72 and methyl cellulose as binders, and respond in various conditions. Design/methodology/approach: It requires using several scientific and analytical techniques to provide a deeper understanding of filling materials characterization, dimensional stability, their shrinkage and study mechanical properties. Findings: The analytical study of filling gaps in wooden objects with different filling materials allowed defining that the main drawbacks of the examined gap fillers were low water resistance, poor dimensional stability upon drying, or exposure to water vapor or liquid water, and fragility. Two types of gap fillers with high mechanical properties and pH values similar to those of wood were found to be appropriate for application on wooden archaeological artifacts. Originality/value: The importance of the experimental study was to determine suitable filling materials and provide the basic characteristics of filling materials reversibility, workability, dimensional stability, lack of shrinkage, drying, ability to take color and be shaped, stability with aging, compatibility with wood in terms of behavior with changing humidity and non-toxicity. Also, strength properties or their likelihood to deform easily allowing changes in the shape of the wooden object during the movement of wood, either of which may be desirable in specific circumstances. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to predict a suitable paper substrate which has high capillary pressure with the tendency of subsequent fluid wrenching in onward direction for the fabrication of microfluidics device application. Design/methodology/approach: The experiment has been done on the WhatmanTM grade 1, WhatmanTM chromatography and nitrocellulose paper samples which are made by GE Healthcare Life Sciences. The structural characterization of paper samples for surface properties has been done by scanning electron microscope and ImageJ software. Identification of functional groups on the surface of samples has been done by Fourier transform infrared analysis. A finite elemental analysis has also been performed by using the "Multiphase Flow in Porous Media" module of the COMSOL Multiphysics tool which combines Darcy's law and Phase Transport in Porous Media interface. Findings: Experimentally, it has been concluded that the paper substrate for flexible microfluidic device application must have large number of internal (intra- and interfiber) pores with fewer void spaces (external pores) that have high capillary pressure to propel the fluid in onward direction with narrow paper fiber channel. Originality/value: Surface structure has a dynamic impact in paper substrate utilization in multiple applications such as paper manufacturing, printing process and microfluidics applications. [ABSTRACT FROM AUTHOR]

Purpose: The aim of the present paper to compare the cleaning treatments of paper samples exposed to artificial aging, toluene and isopropyl alcohol gel in cleaning wax stains. Design/methodology/approach: In total, paper samples were made from wood pulp. They had a deterioration phenomenon represented in the stains of the paraffin wax, so two types of cleaning were used: A traditional method using a toluene solution and another new method using isopropanol gel by a cotton swap in a circular movement until the completion of the cleaning process. Then, all paper samples were treated with toluene and isopropanol to handle the second artificial aging and detect how the samples were affected by artificial aging. For identifying the efficacy of these materials in removing paraffin wax stains, a range of examinations and analyses were used, such as universal serial bus, scanning electron microscope, infrared analysis (IR), pH analysis, color change analysis. Moreover, these results were compared with the standard sample's results. Findings: The results of examinations and analyses proved that the use of toluene affected the paper samples. Their effects were twice as weak, fragile and degraded paper fibers compared to isopropanol gel. Therefore, the isopropanol gel is preferred for paper cleaning to the toluene solution. Originality/value: This paper highlights the efficiency of isopropyl alcohol gel in cleaning wax stains from historical paper supports. [ABSTRACT FROM AUTHOR]

Purpose: The aim of this paper, using the intuitionistic fuzzy (IF)–set based Preference Ranking Organization Method for Enrichment Evaluation (PROMETHEE) method, is to create multicriteria decision-making (MCDM) mechanism that evaluates the papers according to the offset print quality, separately for each of the CMYK colors. Thanks to the mechanism, the most suitable and the most unsuitable paper for printing is determined. Design/methodology/approach: With the IF PROMETHEE method, respectively, deviations are calculated by linear criteria type; the overall IF preference relation matrix is obtained. Finally, the positive and negative outranking flows are calculated; by obtaining net outranking flows, all papers are ranked from best to worst for printability. Findings: Based on the results of the MCDM algorithm; the best offset printing quality is Matte Coated 115 gr. for cyan, magenta and black and Glossy Coated 115 gr. for yellow. The worst offset printing quality for all papers is 70 gr. III. low grade paper. According to the findings, when all colors are examined, the best paper for offset printing quality is coated papers; the worst paper is III. low grade papers. Originality/value: The creation of mechanism that evaluates all criteria together leads to the most accurate result. Cases of hesitation are also addressed using an IF-based algorithm; all criteria were assigned individual importance levels, and a single result was obtained by activating all of the criteria simultaneously. Therefore reasons, this is paper that will bring innovation and shed light on studies in this field. [ABSTRACT FROM AUTHOR]

Purpose: This study aims to examine the effectiveness of the Central Board of Secondary Education (CBSE)-based English textbooks and question papers in developing second-language higher-order thinking skills (HOTS). Design/methodology/approach: Descriptive analysis establishes a causal relationship between learning objectives and second language (L2) writing proficiency. Content analysis is used to compare and analyze tabulated data for textbooks and question papers for the English language by the National Council of Educational Research and Training (NCERT) and CBSE. This method categorizes the materials and their assessments under HOTS and lower-order thinking skills to ascertain the relationship between learning objectives and L2 writing proficiency. Findings: The study highlights teaching material and assessment shortcomings and their alignment with learning outcomes to enhance students' writing skills. It underscores the need for HOTS-focused materials, discussing their impact on writing skills. The study also explores how textbook–question paper mismatch hampers Bloom's taxonomy-based cognitive skills. Practical implications: This research illuminates the efficacy of teaching and learning English as a second language (ESL) writing skills to improve the quality of education, which has real-world implications. The study highlights flaws in the educational system in India and suggests curricular and pedagogical changes. Originality/value: The research examines NCERT and CBSE ESL textbooks and question papers to align teaching and assessment methods. The results aim to improve education through ESL writers' HOTS. [ABSTRACT FROM AUTHOR]

Purpose: In this present study, electrophotographic printing is made on papers which are subjected to different recycling numbers, and this paper aims to examine the colour changes of this printing type. Design/methodology/approach: Four-colour electrophotographic printing is carried out on adhering to the INGEDE 11p standard recycled papers four times under the same conditions. Colour measurements are made by means of electrophotographic printed colour scales printed on these recycled papers. Colour measurements are made with the X-Rite eXact spectrophotometer according to the ISO 13655:2017 standard. As a result of colour measurements, colour differences (ΔL′, ΔH′, ΔC′, ΔE00) of recycled papers are determined using some formulas. Findings: According to the values obtained after four recycling, the highest ΔL′ value is found to be 4.80 yellow and the lowest 1.92 black. Again, according to the measurement results, it is determined that the highest ΔE00 is yellow colour with a value of 5.66, and lowest ΔE00 is black colour with a value of 1.98. In ΔH′, black colour is the highest value of 12.61, the lowest value with −2.05 is obtained in magenta colour. It was observed that the highest ΔC′ value is 2.98 in yellow, and the lowest value is −0.28 in black. Originality/value: In the printing industry, sometimes customers want to monitor the colour differences in the printing by taking the L′a′b′ obtained values as a result of printing from the printing houses. If the colour differences exceed the tolerance values, then they can interfere with the printing. As a result of the calculations, colour changes in electrophotographic printing are observed with many parameters. This study can be a pioneer for the studies that can be done on this subject. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study is to reveal the usability of waste paper sludge on the production of composite materials and the printability of their surfaces were investigated. Design/methodology/approach: First, composite plates were produced by using dried and milled waste sludge together with polyester resin and epoxy. Screen printing using water, solvent and UV-based inks were carried out. Findings: It was determined that UV and solvent-based inks in both resin groups were permanently attached to the surface of composite plates produced using paper mill waste sludge, while it was found that the adhesion was not achieved sufficiently in cardboard factory waste sludge. Originality/value: The unique aspect of this study is obtained the composite plates from paper mill and cardboard mill waste sludge and improved the printability of them. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study is to find an applicable solution for the consolidation of petrified paper after disassembling it to complete other stages of treatment. Design/methodology/approach: The samples were subjected to natural aging by being inoculated with Aspergillus niger until they reached the stage of adhesion and petrification. After that, the leaves were separated, and cellulose nanocrystals were applied, then the leaves were subjected to wet thermal aging for 21 days. Digital microscope, scanning electron microscope, mechanical properties measurement, measurement of color change, Fourier transform infrared spectroscopy and pH measurement were used to evaluate the effects of the cellulose nanocrystal on paper. Findings: The results proved that cellulose nanocrystal (5%) successes consolidation of petrified paper Without affecting its natural, mechanical and chemical properties. Originality/value: This study was based on the effectiveness of cellulose nanocrystal in strengthening the petrified papers and testing its effect on the physical, mechanical and chemical paper properties. [ABSTRACT FROM AUTHOR]

Purpose: This study aims to examine the colour changes affecting inkjet prints after the recycling of papers. Design/methodology/approach: For recycling, papers prepared with the INGEDE 11p standard are recycled four times. Pulping, storage, flotation, beating and bleaching processes are applied for each recycling, respectively. Inkjet prints are made on the obtained test papers, and colour measurements are made using an X-Rite eXact spectrophotometer according to the ISO 13655:2017 standard. These processes are applied again to the papers which are recycled four times, and the results are analyzed. In addition, the values of ΔE00 ′, ΔL′, ΔH ′ and ΔC′ are calculated according to ISO 11664-6:2014 standard by making some calculations according to obtained the L′a′b′ values. Findings: It is determined that the ΔE00 value increases after each recycling in cyan magenta and yellow colour, whereas it decreases in black. The highest ΔE00 value is calculated after the fourth recycling stage is yellow with a value of 8.33. The lowest ΔE00 value detected is black with a value of 0.76 after the fourth recycling stage. This paper observes that the colour with the most variation in hue angle among recycling repetitions is black and the colour with the highest hue angle value is yellow. It is seen that repeating recycling causes increase in the chromatic values of the prints. Originality/value: After the fourth recycling stage, colour changes have reached an important point and can cause important printing problems. In this case, the customer's approval must be obtained to continue printing. This case is valid for ΔE00 values. Colour differences for print contrast, trapping and print chroma values are either not very important or are positive for quality. [ABSTRACT FROM AUTHOR]

Purpose: Paper aims to determinate caking paper manuscript cause through studying of the manuscript components, bio-deterioration and physio-chemical deterioration factor. It will facilitate manuscripts and paper conservators to understand paper blocking and caking phenomenon. Design/methodology/approach: The manuscript condition has been diagnosed by focusing on adhesion and fossilization regions. To achieve this, some methods of analysis and examination were used, such as visual examination, digital microscopy and scanning electron microscope were used to studying surface changes. X-ray diffraction and Fourier transform infrared microscopy were used to determinate of cellulose crystallinity, ink composition and identify the binding medium. Findings: The results revealed the use of cotton pulp, and calcium carbonate was among the fillers that were used to improve the properties of paper. The crystallization of cellulose was lower in the first and last papers than the papers located in the heart of the manuscript. The most important reasons that led to the papers caking was the presence of fungi A. niger, Cladosporium sp, Chaetomium sp, by secreting some enzymes in combination with some other factors such as difference variation in temperature and moisture. Originality/value: All deterioration factors participate with each other until rule the damage circle of the papers because one factor alone cannot stick the papers. It was inferred from the examinations and analyzes that were conducted for the samples. [ABSTRACT FROM AUTHOR]

Purpose: The main objective of this study is to evaluate the impact of Persian Scientific Papers (PSPs) on Persian Wikipedia by studying Wikipedia's citations to these papers. Design/methodology/approach: The present study is applied research, which has been performed by the web-mining method, such as downloading web pages, extracting information (references), identifying papers, detecting peer-review journals and calculating the frequency rates. The statistical population included 10,000 Persian Wikipedia Pages (PWPs) that were analyzed in two rounds with a six-month interval. Findings: The number of pages containing the Persian references section was 3,994 and 4,063 out of the 10,000 pages extracted in the first and second rounds. The ratio of pages that cited scientific sources (58 and 67 pages) to the pages extracted from the PWP was equal to 0.58 and 0.67%. The ratio of pages that cited scientific sources to pages with Persian references in each round was equal to 1.45 and 1.64%. The number of references extracted from the PWP in each round equaled 30,441 and 35,891. Eight titles from reputable Persian journals had received at least three citations from Wikipedia. Originality/value: The present study has determined the extent of interaction between science and society (knowledge flow) in the form of citations from Wikipedia articles to articles in peer-reviewed journals. The study of this issue in Persian Wikipedia in more than 2000 Persian peer-reviewed journals shows the originality of the present paper. Studying citation reliability in a collaborative and openly editable platform is another originality of the work. [ABSTRACT FROM AUTHOR]

Purpose: The surface energy of the printing material can be increased to desired levels with different chemicals or methods. However, the important thing is that the surface properties of printing material are not affected negatively. In this way the aim of this paper provide that the surface properties of matte and glossy coated paper is improved by the argon containing atmospheric pressure plasma device because the plasma treatment method does not occur surface damaging on the papers. Design/methodology/approach: In experimental studies, test samples cut from 160 mm × 30 mm in size from 115 g/m2 gloss- and matt-coated papers were used. The plasma treatments of paper samples were carried out with an argon containing atmospheric pressure plasma device of laboratory scale that produces plasma of the corona discharge type at radio frequency. The optimized plasma parameters were at a frequency of 20 kHz and plasma power 200 W. A copper electrode of length 12 cm and diameter 2.5 mm was placed in the centre of the nozzle. Findings: Research findings showed that the surface energies of the papers increased with the increase in plasma application time. While the contact angle of the untreated glossy paper is 82.2, 8 second plasma applied G3 sample showed 54 contact angle value. Similarly, the contact angle of the base paper of matt coated is 91.1, while M3 is reduced to 60.4 contact angles by the increasing plasma time. Originality/value: Plasma treatment has shown that no chemical coating is needed to increase the wettability of the paper surface by reducing the contact angle between the paper and the water droplet. In addition, the surface energies of all papers treated by argon gas containing atmospheric pressure plasma, increased. Plasma treatment provides to improve both the wettability of the paper and the adhesion property required for the ink, with an environmentally friendly approach. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to outline the initial pilot use of the client complexity matrix (CCM), an outcome measure developed for an NHS Adult Intellectual Disabilities Intensive Support Team (IST) in the West Midlands of England. Design/methodology/approach: A mixed method approach was used to report the results and evaluate the use of the CCM within this IST. The CCM was trialled for six months between January 2022 and June 2022. CCM scores pre and post IST intervention were analysed via t-test, and qualitative feedback from clinicians is detailed. Findings: Analysis suggests the CCM captures service success showing a significant decrease in complexity and risk post-intervention. Qualitative comments from clinicians were generally positive; however, there were requested changes regarding specific presentations, use of labels/language and for a digital version. Research limitations/implications: The tool is not co-constructed with the client. Because of this IST's caseload, the sample size was small. Only one clinician was asked to complete the CCM pre and post intervention. Future use of the measure will encourage two clinicians to complete the measure to evidence its inter-rater reliability. Each client's specific presentation was not explicitly analysed here. Practical implications: The CCM will be updated using the feedback from clinicians and from the peer review process. Research that examines the generalisability of this measure to other IST services would be beneficial. Originality/value: The CCM appears to fill a gap in outcome measurements for this IST service which looks at breadth and depth of client complexity and risk. [ABSTRACT FROM AUTHOR]

Purpose: Correct and well-planned maintenance based on modern global methods directly affects efficiency, quality, direct production costs, reliability and profitability. The selection of an optimal policy for maintenance can be a good solution for industrial units. In fact, by managing constraints such as costs, working hours and human workforce causing sudden equipment failure, production and performance can increase. Design/methodology/approach: Therefore, in this research a model was presented to select the best maintenance strategy at Kaghaz Kar Kasra Co of Iran. In this study, it was tried to integrate the two techniques of goal programming and the technique for order of preference by similarity to ideal solution (TOPSIS) to prioritize maintenance strategies. First, all factors affecting maintenance were identified, and based on the Best Worst Method (BWM) the degree of their importance was determined. Findings: After the evaluation, only 14 criteria in the 4 dimensions of cost, added value, safety and feasibility were selected. The highest points were given to the criteria of equipment cost and depreciation, equipment and personnel performance, equipment installation time and technical feasibility, respectively. In the next stage, using the TOPSIS method the item of maintenance strategy was ranked, and the 3 strategies of preventive maintenance (PM), predictive maintenance (PDM) and corrective maintenance (CM) were chosen. Modeling was performed utilizing a goal programming approach to select the optimal maintenance strategy for 13 devices. All the technical specifications, cost limits and the device time were extracted. After the model was finished and solved the best item for each device was specified. Originality/value: 1. Developing a goal programming model and decision-making dashboard. 2. Identifying the criteria and factors affecting the selection of the maintenance strategy for paper production Industry [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to investigate the influences of coating colours and their contents on the fundamental properties of base papers and also evaluate these results in terms of mechanical and wood-free papers. Design/methodology/approach: A design research approach has been based on the application of various coating colours and analysis of mechanical and optical tests results of the coated mechanical and wood-free base papers. Findings: This study is confirmed that the coating colours can be easily applied to the surface of the papers. The experimental data have revealed that significant improvements exist in the values of tear resistance (strength), brightness and opacity of the mechanical base papers, especially by the application of the coating colours including kaolin pigment. The results show that mechanical papers can also be used in areas with high brightness expectations by applying coating colour. Originality/value: The originality of this work is based on understanding and comparing the effects of applying similar coating formulations on mechanical and wood-free base papers. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to present the components' characterization and condition assessment of an important deteriorated Mamluk-illuminated paper manuscript housed in Al-Azhar Library, Egypt. Design/methodology/approach: Different analytical techniques used in this study were the portable digital optical microscope, stereomicroscope, scanning electron microscope with EDX (SEM.EDX), portable X-ray fluorescence (pXRF), X-ray diffraction (XRD), pH measurement and Fourier transform infrared spectroscopy (FTIR). Findings: The results obtained by different microscopes showed that the gilding in the surface of illuminated paper sheets was performed with gold leaves. Additionally, these microscopes revealed that the illuminated paper manuscript has different aspects of deterioration such as adhered dirt, staining, some micro-cracks, cracks and detachment of some parts in some illuminated areas. The results of elemental analysis by EDX, portable XRF and XRD analysis showed that the orange red pigment is red lead (Pb3O4), blue pigment is azurite (2CuCo3.Cu (OH)2), and the gold layer is has consisted of brass alloy (Cu-Zn) with a small amount of gold element (Au). The pH measurement stated that the historical paper in the acidity level. The ATR-FTIR analysis also revealed the oxidation of cellulose. Moreover, it was found from ATR-FTIR that Arabic gum was used as a binder for the pigments. Originality/value: This study presents the important results of analytical methods used for condition assessment and identification of the components of an important Mamluk-illuminated paper manuscript, where these results referred that the studied paper manuscript had different aspects of deterioration. The conservation steps either conservation treatment or preventive conservation are urgently needed in future studies. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study was to design a paper strip-based non-invasive urine analysis system for the qualitative detection of biomarker aquaporin-1 (AQP1) in renal cancer (RC). RC accounts for 3% of all cancers and 85% of all kidney tumors and mainly originates from the kidney cortex. In recent times, higher urine concentration of AQP1 in patients with RC was confirmed as a specific biomarker of the disease. Hence, the noninvasive, user-friendly and self-diagnostic method is required for the detection of aquaporin biomarkers in RC. Design/methodology/approach: The present research work was focused on the development and characterization of a dye conjugated cyclodextrin-based miniaturized system for impregnation on Whatman filter paper to identify RC using AQP1 biomarker present in urine samples. Findings: It was observed that the test strip dipped into the urine sample, and the yellow color intensity increased with a decrease in AQP1 concentration due to the transformation of the dye system of free basic form into bound acidic form. The Hue-Saturation-Value profiling was used to observe the effect of color change using a smartphone application. The paper strip-based urine analysis system is highly sensitive for the detection of AQP1 in the range of 10 to 1,000 ng. Originality/value: The successful validation indicated that this biosensor is likely to contribute to the development of point-of-care, novel, personalized diagnostics and ensure prolonged survival of RC patients in the near future. [ABSTRACT FROM AUTHOR]

Purpose: With the aid of libraries, the research paper aims to assist businesses in swiftly and accurately acquiring knowledge and insights from scholarly literature to guide their inventive and decision-making processes. The foundation for achieving the goal is Connected Papers technology. Design/methodology/approach: The author's professional expertise in performing literature reviews using connected papers technology as well as using other ways, and corresponding with entrepreneurs and librarians impacted the article's research methodology. Findings: The use of Connected Papers technology in the library context for helping entrepreneurs is discussed. Libraries and entrepreneurs could benefit from using Connected Papers technology to quickly compile pertinent data from scholarly literature to solve business challenges. According to the paper, adopting this technology can speed up information gathering and drastically reduce the time needed for business owners to search through bibliographic data-bases. Using this technology can help entrepreneurs at various phases of their entrepreneurial journeys and give libraries a productive way to assist business owners with their information needs. Originality/value: This paper's novelty comes from its examination of the usage of connectedpapers.com technology to compile data from scholarly literature to assist entrepreneurs in solving their business problems. The useful piece of advice this paper offers entrepreneurs and librarians is what makes it valuable. By using connectedpapers.com technology, businesses may be able to get critical information from scholarly literature to foster a series of experimentation quickly and effectively. Also, librarians can help their patrons with systematic re-views and other research services by using this application. [ABSTRACT FROM AUTHOR]

Purpose: This study aims to provide control of liquids, especially against water-based ink on the paper and paperboard surface with natural substances, in also practical and greenway. Design/methodology/approach: The paper surface was treated with natural rosin and its derivatives to obtain a hydrophobic effect and to improve printing properties. The oleoresin samples collected from Pinus nigra Arnold and Pinus pinaster Aiton trees in the controlled area and turpentine content removed was by hydrodistillation. The gum rosin (GR), fortified 10% with maleic anhydride (MGR) and esterified with 10% pentaerythritol (PMGR) samples solved in a simply alcohol and sprayed the base paper surface directly with a spray gun. Base paper samples were paperboard, bleached paper and test liner paper. Then, flexo printing was applied and printability properties were measured. Findings: The treatment weights of these paper samples were 1.8 ± 0.5, 1.3 ± 0.5 and 0.7 ± 0.2 g/m2, respectively, compared to the base paper. Greater Cobb60 results were obtained from modified rosin samples than unmodified gum rosin-sized paperboards and the PMGR surface treatment reduces Cobb60 values by 20% and MGR treatment reduces 15% comparing to the base sheet. Then, the printing procedure was applied to the surface of the treated materials using a flexo printing system. As a result of the treatment better print density, chroma and print lightness value consumed a less hydrophobic agent and controlling water-based flexo ink on the base paper surface. Originality/value: The unique aspect of this work was improving the hydrophobicity of the paper surfaces was achieved by spraying with natural rosin and derivatives. [ABSTRACT FROM AUTHOR]

Purpose: In the current study, the authors prepared conductive nano-structured thin films composed of copper on the surface of the printed paper using a magnetron sputtering system. Furthermore, the printability of conductive films for the sake of re-using printed paper and its additional applications were also investigated. Design/methodology/approach: Paper-based electronic devices have been the matter of intense interest because of their easy accessibility, lightweight, low cost, biodegradable, recyclable and ecofriendliness. Furthermore, these devices are inexpensive compared to other substrates. Nowadays, flexible energy and electronic devices made of the paper substrate are receiving a significant interest because of the issue of sustainable energy production from the environment. One of the most reliable techniques for the deposition of thin films and creating conductive patterns on the paper is magnetron sputtering. Findings: The printed and coated printed papers were evaluated with X-ray powder diffraction, scanning electron microscopy with energy-dispersive (SEM-EDX), four-point probe conductivity and spectroscopic measurements. Practical implications: The paper investigates the printability of conductive paper attributable to its second application. Originality/value: The authors prepared conductive nanostructured copper-based thin films on the surface of the printed paper. They recovered and reused the paper as a root of raw material due to the environmental issue. [ABSTRACT FROM AUTHOR]

Purpose: This study aims to restore the lost mechanical properties of the prints with carrageenan, methyl hydroxyethyl cellulose (Tylose) and hydroxypropyl methylcellulose (Methocel). Design/methodology/approach: The effect of these materials on the properties of the printed paper (modern and historical samples) has been evaluated under the influence of accelerated aging using pH measurement, the mechanical properties (tensile and elongation), FTIR and color changes. Findings: The three consolidates reduced the acidity of treated samples significantly, but after ageing, it was observed that the pH of aged treated samples decreased slightly as compared to the untreated samples. The results of the mechanical properties showed the superiority of hydroxypropyl methylcellulose (Methocel) in improving the tensile and elongation forces of the samples compared to carrageenan and methyl hydroxyethyl cellulose even during the accelerated aging. Consolidation materials succeeded in reducing ΔE of the paper samples under accelerated aging, especially carrageenan. The IR spectra confirmed that no dramatic difference was observed in topically function vibrations of samples after treatment beside that the O-H stretching band intensity increased observably after treatment with the three consolidates, after ageing the treatment, and it protected the treated paper from oxidation processes as the infrared spectrum analysis showed a decrease in intensities of carbonyl and carboxyl groups as compared to aged untreated samples. Originality/value: The research provides new biopolymers in strengthening the historical printed paper, where printed papers lack studies related to their conservation. This makes the current study a promising step for treating historical printed paper. [ABSTRACT FROM AUTHOR]

Purpose: In flexible electronics applications, organic inks are mostly used for inkjet printing. Three-dimensional (3 D) printing technology has the advantages of low cost, high speed and good precision in modern electronic printing. The purpose of this study is to solve the high cost of traditional printing and the pollution emissions of organic ink. It is necessary to develop a water-based conductive ink that is easily degradable and can be 3 D printed. A nano-silver ink printed circuit pattern with high precision, high conductivity and good mechanical properties is a promising strategy. Design/methodology/approach: The researched nano-silver conductive ink is mainly composed of silver nanoparticles and resin. The effect of adding methyl cellulose on the ink was also explored. A simple 3 D circuit pattern was printed on photographic paper. The line width, line length, line thickness and conductivity of the printed circuit were tested. The influence of sintering temperature and sintering time on pattern resistivity was studied. The relationship between circuit pattern bending performance and electrical conductivity is analyzed. Findings: The experimental results show that the ink has the characteristics of low silver content and good environmental protection effect. The printing feasibility of 3 D printing circuit patterns on paper substrates was confirmed. The best printing temperature is 160°C–180°C, and the best sintering time is 30 min. The circuit pattern can be folded 120°, and the cycle is folded more than 60 times. The minimum resistivity of the circuit pattern is 6.07 µΩ·cm. Methyl cellulose can control the viscosity of the ink. The mechanical properties of the pattern have been improved. The printing method of 3 D printing can significantly reduce the sintering time and temperature of the conductive ink. These findings may provide innovation for the flexible electronics industry and pave the way for alternatives to cost-effective solutions. Originality/value: In this study, direct ink writing technology was used to print circuit patterns on paper substrates. This process is simple and convenient and can control the thickness of the ink layer. The ink material is nonpolluting to the environment. Nano-silver ink has suitable viscosity and pH value. It can meet the requirements of pneumatic 3 D printers. The method has the characteristics of simple process, fast forming, low cost and high environmental friendliness. [ABSTRACT FROM AUTHOR]

Purpose: This study distinguishes the academic influence of different papers published in journals of the same subject or field based on the modification of the journal impact factor. Design/methodology/approach: Taking SSCI journals in library and information science (LIS) as the research object, the authors first explore the skewness degree of the citation distribution of journal articles. Then, we define the paper citation ratio as the weight of impact factor to modify the journal impact factor for the evaluation of papers, namely the weighted impact factor. The authors further explore the feasibility of the weighted impact factor in evaluating papers. Findings: The research results show that different types of skewness exist in the citation distribution of journal papers. Particularly, 94% of journal paper citations are highly skewed, while the rest are moderately skewed. The weighted impact factor has a closer correlation with the citation frequency of papers than the journal impact factor. It resolves the issue that the journal impact factor tends to exaggerate the influence of low-cited papers in journals with high impact factors or weaken the influence of high-cited papers in journals with low impact factors. Originality/value: The weighted impact factor is constructed based on the skewness of the citation distribution of journal articles. It provides a new method to distinguish the academic influence of different papers published in journals of the same subject or field, then avoids the situation that papers published in the same journal having the same academic impact. [ABSTRACT FROM AUTHOR]

Purpose: The conditions that domain analysis becomes an academic school of information science (IS) are mature. Domain analysis is one of the most important foundations of IS. The purpose of this paper is to analyze and discuss metatheoretical and theoretical issues in the domain analytic paradigm in IS. Design/methodology/approach: This paper conducts a systematic review of representative publications of domain analysis. The analysis considered degree theses, journal articles, book chapters, conference papers and other materials. Findings: Domain analysis maintains that community is the new focus of IS research. Although domain analysis centers on the domain and community, theoretical concerns on the social and individual dimensions of IS are inherent in it by its using sociology as its important approach and socio-cognitive viewpoint. For these reasons domain analysis can integrate social–community–individual levels of IS discipline as a whole. The role of subject knowledge in IS is discussed from the perspective of domain analysis. Realistic pragmatism that forms the philosophical foundation of domain analysis is argued and the implications of these theories to IS are presented. Originality/value: The intellectual evolving landscape of domain analysis during a quarter century is comprehensively reviewed. Over the past twenty-five years, domain analysis has established its academic status in the international IS circle. Being an important metatheory, paradigm and methodology, domain analysis becomes the theoretical foundation of IS research. This paper assesses the current state of domain analysis and shows the contributions of domain analysis to IS. It also aims to inspire further exploration. [ABSTRACT FROM AUTHOR]

Purpose: In this article, the ideas and methods behind the "patent-paper citation" are scrutinised by following the intellectual and technical development of approaches and ideas in early work on patentometrics. The aim is to study how references from patents to papers came to play a crucial role in establishing a link between science and technology. Design/methodology/approach: The study comprises a conceptual history of the "patent paper citation" and its emergence as an important indicator of science and technology interaction. By tracing key references in the field, it analyses the overarching frameworks and ideas, the conceptual "hinterland", in which the approach of studying patent references emerged. Findings: The analysis explains how interest in patents – not only as legal and economic artefacts but also as scientific documents – became evident in the 1980s. The focus on patent citations was sparked by a need for relevant and objective indicators and by the greater availability of databases and methods. Yet, the development of patentometrics also relied on earlier research, and established theories, on the relation between science and technology. Originality/value: This is the first attempt at situating patentometrics in a larger societal and scientific context. The paper offers a reflexive and nuanced analysis of the "patent-paper citation" as a theoretical and historical construct, and it calls for a broader and contextualised understanding of patent references, including their social, legal and rhetorical function. [ABSTRACT FROM AUTHOR]

Purpose This paper aims to investigate the effect of acidity on the morphology of archeological paper, especially in the presence of colors and whether natural pigments play a role in the process of degradation.Design/methodology/approach The morphological changes in the cellulosic fibers of the manuscripts because of acidity were investigated using environmental scanning electron microscope (ESEM). Ten historical samples were collected from different manuscripts suffering from acidity. X-ray diffraction was used to identify the inks and pigments that were used in some samples. Additionally, Fourier transform infrared microscopy was used to identify the binding medium.Findings The results confirmed that carbon ink, ultramarine, cinnabar and gold pigments were applied to some manuscripts with Arabic gum. As for ESEM investigation, the results proved that acidity badly affected the integrity of the cellulosic fibers resulting in their embrittlement. The micrographs showed differences in fiber degradation according to pH value. The presence of inks and pigments increased the degradation extent resulting from acidity.Originality/value This paper addresses a specific need to study the behavior of degradation in paper manuscripts, thus helping the conservators find solutions to the phenomenon. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to identify the most common fungal species that grow on paper manuscripts and cause bio-deterioration. It also detects the impact of additive materials on fungal degrading and builds a wide database. Thus, it helps conservators understand this phenomenon. Design/methodology/approach: In total, 15 samples were collected from different paper manuscripts suffering from fungi. The achievement of the study objectives depends on using a variety of analyzes, such as a microbiological study, which indicated that three main fungi grew on the paper samples. Then, a digital microscope and an environmental scanning electron microscope were used to detect the effect of fungi on paper fibers. Fourier transform infrared microscopy was used to identify the binding medium and the X-ray diffraction method was used to measure the crystallinity index of cellulose of the paper samples. Findings: Arabic gum was used as a binder medium with the samples. Aspergillus Niger, Aspergillus Fumigatus and Aspergillus Clavatus were the most common fungal species that grew on the Qur'an papers under investigation. They also caused much common damage to the paper samples. The results of the analyzes also showed that the highest crystallinity index of cellulose was in the samples that contained the lowest rate of fungal growth. Originality/value: This paper highlights the relationship between fungal degradation and the multi-component nature of paper manuscripts. It builds a wide database that correlates the composition and the degradation of the Qur'an papers. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to provide empirical insight into the use of the term and concept of grey literature in recent scientific papers. Design/methodology/approach: The author conducted a scientometric analysis with Scopus data on 1,606 papers mentioning grey (or gray) literature published in 2018. Additionally, the author analysed the evolution between 1999 and 2018, and performed a content analysis on a random subsample of 70 papers in open access. Findings: The percentage of papers that mention grey literature is low (0.05%) but steadily rising. They are from over 100 countries and a long tail of institutions, covering, namely, medical and health sciences and related topics. The dominant document type is systematic reviews, defining grey literature generally thought of as "unpublished", "not peer reviewed" and "not in databases" and meaning, most of the time, all kinds of reports and conference papers. A large variety of sources and options on how to retrieve grey literature is mentioned, including Google and Google Scholar, specialised digital libraries, relevant websites, handsearching in bibliographic references and contact with experts in the field. Research limitations/implications: The study is limited to papers indexed in the Scopus database, mainly journals, written in English, with a bias in favour of medical and life sciences. Originality/value: There is no recent study on the real usage of the term of grey literature in a large sample of academic papers. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to study friction and wear properties of three types of steels against paper-based friction disc, including 65Mn, 20#steel and 30CrAl, so as to obtain the appropriate working conditions for different friction materials in the transmission system. Design/methodology/approach: Based on actual working conditions, pin-on-disc tests are conducted on a universal material tester. The two evaluation indexes, including average friction coefficient and variation coefficient, are introduced to analyze the different friction properties among three types of steel. Furthermore, the temperature-dependent wear pattern and wear depth are subsequently studied. Findings: The results show that 65Mn is more suitable for working under heavy load and low velocity, but 30CrAl and 20#steel are suitable for working under light load and high velocity. Moreover, wear primarily occurs on paper-based material and peaks at about 325. Practical implications: This research of different materials and friction property for friction pairs is helpful to improve the performance and prolong the service life of transmission systems. Originality/value: Suitable working conditions of different friction materials are obtained, and the correlation between wear and decomposition in high temperature is verified. [ABSTRACT FROM AUTHOR]

Purpose This study aims to analyse the impact of e-paper on many existing industries including paper, publishing, book distribution, display, handheld device manufacturers and content service providers. Flexible display has been studied by many institutes, firms and market research companies. Some believe that e-paper is an exceptional application for flexible display, and the need for flexible display development for handheld devices and cloud-based e-book content is indisputable.Design/methodology/approach This study uses the Delphi technique and STEEP (Sociological, Technological, Economic, Environmental and Political aspects) with a panel to analyse a business model and the opportunity for the development of e-paper in Taiwan up to the year 2020.Findings The study concludes that e-paper content and customised digital services are an essential part of e-paper development, while hardware and cloud data are no more than a mechanism to show, compute and store data. Thus, whether the screen of a handheld device is flexible may not be of importance. Although e-paper will affect the display industry, it will not substitute for handheld devices and traditional bookstores.Originality/value This research can be used as a reference for government, academics, industry and international investors. [ABSTRACT FROM AUTHOR]

Purpose: In 2017, one study (Derek Pyne; Journal of Scholarly Publishing; DOI: 10.3138/jsp.48.3.137; University of Toronto Press) in the "predatory" publishing literature attracted global media attention. Now, over three years, according to adjusted Google Scholar data, with 53 citations (34 in Clarivate Analytics' Web of Science), that paper became that author's most cited paper, accounting for one-third of his Google Scholar citations. Design/methodology/approach: In this paper, the authors conducted a bibliometric analysis of the authors who cited that paper. Findings: We found that out of the 39 English peer-reviewed journal papers, 11 papers (28%) critically assessed Pyne's findings, some of which even refuted those findings. The 2019 citations of the Pyne (2017) paper caused a 43% increase in the Journal of Scholarly Publishing 2019 Journal Impact Factor, which was 0.956, and a 7.7% increase in the 2019 CiteScore. Originality/value: The authors are of the opinion that scholars and numerous media that cited the Pyne (2017) paper were unaware of its flawed findings. [ABSTRACT FROM AUTHOR]

Purpose: The paper examines three English research papers on self-neglect, from 1957, 1966 and 1975, discussing them in the context of more recent thinking and the statutory framework in England. Design/methodology/approach: In reviewing the three research papers, developments and points of continuity in the field of self-neglect were identified and are discussed in this paper. Findings: In light of the findings of the three articles, the present paper traces some of the classificatory refinements in this field that have taken place since the papers were published, notably in respect of hoarding and severe domestic squalor. Some of the difficulties in making judgements about behaviour thought to breach societal norms are described, and the challenges practitioners face in intervening in cases, particularly where the person concerned is refusing assistance, are examined. Originality/value: By drawing on the historical research context, the paper contributes to our current understanding of the field of self-neglect. [ABSTRACT FROM AUTHOR]

Purpose: Inspired by the development of eco-friendly flexible electronics, this paper aims to present a series of paper-based electronics drawn by pencils, which can be used as favorable sensing elements in daily life. Design/methodology/approach: Pencil traces are deposited on the porous surface of Xerox paper by the mechanical exfoliation during writing process, which can be used as basic components to construct functional electronics for daily sensing applications. By changing pencil grade, the obtained traces can work as conductive wires, electrodes, resistors and piezoresistive gauges. Findings: The experimental results confirm their practical applications in sensing several daily activities, including finger motion, touching and the temperature of water in paper cup. Moreover, the used electronics can be easily handled and recycled. Research limitations/implications: The shortage in functionality, reliability and performance consistency induced by manual operation is an evident challenge, which makes the pencil-on-paper devices more suitable to work as a temporary solution to satisfying the demands from emergency circumstances. Originality/value: The pencil-on-paper devices, motivated by the electroconductibility and piezoresistivity of pencil trace, can be explored as sensing prototypes in detecting daily activities. Meantime, their advances in easy accessibility, rapid fabrication, low cost and eco-fitness endow them excellent capacity of meeting the "on-site, real-time" demands. [ABSTRACT FROM AUTHOR]

Purpose: What is the behavior of nano-polaroid in strengthening weak paper? What is the effect of adding nano-zinc oxide to nano-polaroid? This paper aims to answer these questions. Design/methodology/approach: A number of weak historical papers dating back to 1829 AD were treated with 2% of nano-polaroid and polaroid zinc oxide nanocomposites, respectively. After dryness, the samples were subjected to ultraviolet–ozone accelerated aging. Then, the effectiveness of the treatment was defined using the mechanical properties measurement, pH measurement, the chromatic change, scanning electron microscope investigation of the fibers surface and attenuated total reflectance analysis. Findings: Results revealed that N-polaroid strengthened the fiber surface without reducing the gloss of ink. With the loading of nano-zinc particles onto N-polaroid, the strengthening effect increased, especially after the aging processes where the tensile and elongation values reached the highest value. Not only this but also the nano-polaroid coated with ZnO NPs reduced the color change and yellowness during aging, where the ΔE value reached to 3.3 (an acceptable degree of change, not monitored by the naked eye). The acidity of the treated paper also decreased significantly after the treatment and the aging. The microscopic images detected the improvement of the fibers' structure where the fibers were swollen by the absorption of nanocomposites, which can be attributed to ZnO (NPs) that decreased the contact angle between the cellulose and the N-polaroid, which helped in filling the primary cells of fibers. Originality/value: The study addressed the reinforcement of the printed paper samples using nano-polaroid and ZnO polaroid nanocomposites. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to study and compare the friction stability of wet paper-based clutches with regard to the radial grooves (RG) and waffle grooves (WG). Design/methodology/approach: This paper presents an experimental study of a wet clutch concerning the effect of groove patterns on the friction torque and surface temperature. The friction stabilities of RG and WG are investigated with the applied pressure, rotating speed and automatic transmission fluid (ATF) temperature taken into consideration. Findings: The friction torque and surface temperature of WG are larger than those of RG under the same operating condition. The friction torque difference between RG and WG grows with the increase of applied pressure and narrows with the increase of ATF temperature. Additionally, their temperature difference expands via increasing the rotating speed and ATF temperature or reducing the applied pressure; in this way, not only the variable coefficient difference between RG and WG can be narrowed, but also the friction stability of the clutch can be improved dramatically. Originality/value: This paper explains the thermodynamic differences between RG and WG; moreover, it is verified experimentally that WG has a better friction stability than RG. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study was to develop flexible sensors for detection of different concentrations of bacteria, such as Pseudomonas aeruginosa and Staphylococcus aureus, in saline. Design/methodology/approach: The sensors were fabricated using ink-jet printing technology and they consist of a pair of silver interdigitated electrodes printed on mechanically flexible substrates – foil and paper. In house measurement setup for testing and characterization of sensors has been developed. Structural, electrical and mechanical properties of flexible sensors have been determined and compared. Findings: The characteristics of sensor – the resonant frequency as a function of different concentrations of each bacteria – are presented. The obtained results demonstrate different resonant frequencies for each dilution of Pseudomonas aeruginosa and Staphylococcus aureus in physiological saline. Research limitations/implications: Both sensors showed accurate measurements of bacterial count, which can be achieved with detection of resonant frequency, and this is reflective of the number of bacterial cells within a sample. Practical implications: The findings suggest that the newly developed method based on measuring resonant frequency corresponds well with bacterial cell count, thus establishing a new proof-of-concept that such method can have significant applications in bacterial cell counting that are economic and easily maintained. Social implications: Fast, cost-effective, accurate and non-invasive method for detection of different bacteria from saline was developed. Originality/value: For the first time, comparison between performances of flexible sensors on foil and paper for bacteria detection is demonstrated. Almost linear dependence between shift of resonant frequency of developed sensors and concentration of bacteria has been obtained. [ABSTRACT FROM AUTHOR]

Purpose: The current article presents the results of a case study dealing with the historical roots of Eastern European researchers in computer science. Design/methodology/approach: The study is based on an analysis of cited references stemming from a collection of around 80,000 computer science papers by Eastern European researchers published from 1989 to 2014. By using a method called "reference publication year spectroscopy" (RPYS) for historical analyses based on bibliometric data, we analyze around 800,000 references cited in those papers. The study identifies the peak years, including most frequently cited publications (from 1952, 1965 and 1975), and focuses on these outstanding works for the field. The research shows how these influential papers were cited in Eastern Europe and in general, and on which scientific fields they have the most impact. Findings: A noteworthy publication that seems to have a tremendous effect on Eastern European computer science is Zadeh's "Fuzzy sets" article which appeared in Information and Control in 1965. The study demonstrates that computer scientists from Eastern Europe are more conservative in their citation behaviour and tend to refer to older and more established research than their counterparts from the West. Originality/value: Which are the historical roots of researchers working in a particular field or on a specific topic? Are there certain publications – landmark papers – which are important for their research? We guess that these are questions bothering researchers in many fields. [ABSTRACT FROM AUTHOR]

Purpose – This paper aims to report on corrosivity of secondary-stage paper mill effluent and corrosion performance of stainless steels. Design/methodology/approach – For this purpose, immersion test and electrochemical polarization tests were conducted in mill and synthetic effluent to evaluate the uniform and localized corrosion. Findings – Corrosivity of mill effluent has been compared with synthetic and primary-stage effluent of the same mill. It is observed that anions present in them, viz. SO4−, PO34−, NO2− and NO3−, impart inhibition, whereas Cl− and chlorophenols enhance the corrosivity of the effluent. The overall effect of various components was reduction in corrosivity of secondary mill effluent. Originality/value – These observations can be useful for material selection and helpful in corrosion mitigation in paper mill effluent treatment plants. [ABSTRACT FROM AUTHOR]

Purpose: As it is known, the electrostatic discharge (ESD) protection design of integrated circuit is very important, among which the silicon controlled rectifier (SCR) is one of the most commonly used ESD protection devices. However, the traditional SCR has the disadvantages of too high trigger voltage, too low holding voltage after the snapback and longer turn-on time. The purpose of this paper is to design a high-performance SCR in accordance with the design window under 0.25 µm process, and provide a new scheme for SCR design to reduce the trigger voltage, improve the holding voltage and reduce the turn-on time. Design/methodology/approach: Based on the traditional SCR, an RC-INV trigger circuit is introduced. Through theoretical analysis, TCAD simulation and tape-out verification, it is shown that RC-INV triggering SCR can reduce the trigger voltage, increase the holding voltage and reduce the turn-on time of the device on the premise of maintaining good robustness. Findings: The RC-INV triggering SCR has great performance, and the test shows that the transmission line pulse curve with almost no snapback can be obtained. Compared with the traditional SCR, the trigger voltage decreased from 32.39 to 16.24 V, the holding voltage increased from 3.12 to 14.18 V and the turn-on time decreased from 29.6 to 16.6 ns, decreasing by 43.9% the level of human body model reached 18 kV+. Originality/value: Under 0.25 µm BCD process, this study propose a high-performance RC-INV triggering SCR ESD protection device. The work presented in this paper has a certain guiding significance for the design of SCR ESD protection devices. [ABSTRACT FROM AUTHOR]

Purpose – This paper aims to investigate the effect of paper properties (whiteness, gloss and roughness) on colour laser printing quality. Paper characteristics have a significant influence on print quality and are crucial variables for predicting and reproducing colour. Design/methodology/approach – Six kinds of paper with different properties were selected and the effects of the paper characteristics on the printed paper were studied. Samples were printed with cyan, magenta and yellow toner with a laser printer under identical conditions. The papers and printed papers were evaluated with atomic force microscope, scanning electron microscope, gloss-meter, spectrophotometer and densitometer. Findings – Results showed that print quality is statistically dependent on paper type, and the average optical density of printed paper varied for different papers. Furthermore, the increase in the roughness and gloss of the papers in comparison to whiteness more significantly affected the optical density of paper by reducing it. Practical implications – To achieve high-quality print, laser printing paper and toner require controlled characteristics. Originality/value – For the first time, the present study evaluated the influence of paper properties on the quality of colour laser printing. [ABSTRACT FROM AUTHOR]

Purpose -- Conference publications are an important aspect of research activities. There are generally both oral presentations and poster sessions at large international conferences. One can hypothesise that, for the same conferences, the papers presented in oral sessions should have a higher research impact than the papers presented in poster sessions. However, there has been no related study examining the validity of this hypothesis. In other words, the difference of research impact between papers presented orally or during poster sessions has not been discussed in literature. Therefore, the purpose of this paper is to conduct a citation analysis to compare the research impact of papers presented in oral and poster sessions. Design/methodology/approach -- In this paper, data from three leading conferences in the field of computer vision are examined, namely CVPR (2011 and 2012), ICCV (2011) and ECCV (2012). Several types of citation-related statistics are collected, including the number of highly cited papers (i.e. high number of citations) presented in oral and poster sessions, the total citations of both types of papers, the average citations of oral and poster papers, and the average citations of each frequently cited paper of both types. Findings -- There are three main findings. First, a larger proportion of highly cited papers are from oral sessions than poster sessions. Second, the average number of citations per paper is larger for those presented in oral sessions than poster sessions. Third, the average number of citations for highly cited papers presented in oral sessions is not necessarily greater than for the ones presented in poster sessions. Originality/value -- The originality of this paper is that it is the first attempt to examine the differences of citation impacts of conference papers presented in oral and poster sessions. The findings of this study will allow future bibliometrics research to further explore this related issue for longer periods and different fields. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to investigate the usage, captures, mentions, social media and citations of highly cited papers of Library and information science (LIS). Design/methodology/approach: This study is quantitative research that was conducted using scientometrics and altmetrics indicators. The research sample consists of LIS classic papers. The papers contain highly cited papers of LIS that are introduced by Google Scholar. The research data have been gathered from Google Scholar, Scopus and Plum Analytics Categories. The data analysis has been done by Excel and SPSS applications. Findings: The data indicate that among the highly cited articles of LIS, the highest score regarding the usage, captures, mentions and social media and the most abundance of citations belong to "Citation advantage of open access articles" and "Usage patterns of collaborative tagging systems." Based on the results of Spearman statistical tests, there is a positive significant correlation between Google Scholar Citations and all studied indicators. However, only the correlation between Google Scholar Citations with capture metrics (p-value = 0.047) and citation metrics (p-value = 0.0001) was statistically significant. Originality/value: Altmetrics indicators can be used as complement traditional indicators of Scientometrics to study the impact of papers. Therefore, the Altmetrics knowledge of LIS researchers and experts and practicing new studies in this field will be very important. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to examine the quantum of research papers and the citations these papers received for the plant Jatropha curcas Linn. Design/methodology/approach: Articles published on Jatropha curcas Linn during 1987–2016 were downloaded from Science Citation Index-Expanded (SCIE) by using the keyword Jatropha* on October 18, 2017. The search resulted in 4,276 records in all. The authors analyzed only 4,111 documents which were published as review articles, research articles and proceeding papers using the complete count methodology. The data were analyzed to examine the pattern of growth of output, most prolific countries, institutions and authors. It also identified highly cited authors and journals used for communicating research results. Findings: The study indicates that India, China and Brazil are the main contributors to the field and the pattern of growth indicates a steep rise in publication output especially in the last block of 2015–2016. Most of the prolific institutions and authors were also located in these countries. However, the impact of output was different from the pattern of output. The publication output is scattered in more than 1,000 journals published from different parts of the globe. Originality/value: The plant of Jatropha curcas Linn is a highly useful plant as a source of biofuel energy. This is the second study in English language on this plant and has used a large set of publication data as compared to the first. The findings of the study may be useful for policy makers as well as for researchers working in the field of biofuel energy. [ABSTRACT FROM AUTHOR]

Purpose: There is a wealth of value hidden in regional cultural heritage, but its preservation status is not optimistic. This study introduces a method that focuses on the inherent cultural value of regional cultural heritage to preserve it by value construction and release. Design/methodology/approach: Based on the great value of regional cultural heritage due to spatial adjacency and temporal continuity, this paper focuses on its inherent cultural value to explore the preservation path and chooses Shichahai cultural heritage digital resources for a case study. This paper draws lessons from the narrative method of ancient Chinese historiography, constructs a cultural space and tells cultural stories. A linked data organization model for digital resources is created to construct a conceptual cultural space. Then, the space is materialized by linked dataset creation. The authors tell cultural stories discovered from the space, which are presented by various user interfaces using visualization technologies. Findings: A cultural space promotes the development of a fine-grained description of regional cultural heritage and aids in relationship discovery to enhance the value construction ability. Additionally, storytelling via interactive user interfaces is helpful in the utilization and dissemination of knowledge extracted from a cultural space and enhances the value release of regional cultural heritage. In this way, a path with the inherent cultural value of regional cultural heritage as the core is established, and preservation is achieved. Originality/value: This study focuses on the inherent cultural value of regional cultural heritage and proposes a new path to preserve these resources. This approach will enrich research on the preservation of regional cultural heritage and contribute to the construction and release of its cultural value. [ABSTRACT FROM AUTHOR]

Purpose: Retail investors are prone to be affected by information dissemination in social media with the rapid development of Web 2.0. The purpose of this study is to recognize the factors that may impact users' retweet behavior, namely information dissemination in the online financial community, through machine learning techniques. Design/methodology/approach: This paper crawled data from the Chinese online financial community (Xueqiu.com) and extracted author-related, content-related, situation-related, stock-related and stock market-related features from the dataset. The best information dissemination prediction model based on these features was determined by evaluating five classifiers with various performance metrics, and the predictability of different feature groups was tested. Findings: Five prevalent classifiers were evaluated with various performance metrics and the random forest classifier was proven to be the best retweet prediction model in the authors' experiments. Moreover, the predictability of author-related, content-related and market-related features was illustrated to be relatively better than that of the other two feature groups. Several particularly important features, such as the author's followers and the rise and fall of the stock index, were recognized in this paper at last. Originality/value: This study contributes to in-depth research on information dissemination in the financial domain. The findings of this study have important practical implications for government regulators to supervise public opinion in the financial market. [ABSTRACT FROM AUTHOR]