Search

Multilevel inverters (MLIs) are being used in wide range of power electronic applications. These converters have attracted a lot of attention during recent years and exist in different topologies with similar basic concepts. This paper presents five main submodules (SMs) to be used as the basic structures of MLIs. The paper reviews the common MLI topologies from the structural point of view. The topologies are divided into the different SMs to show conventional MLI configurations and future topologies that can be created from the main SMs. A comparative study between different topologies is performed in detail. The MLIs are categorized and investigated with from different perspectives such as the number of components, the ability to create inherent negative voltage, working in regeneration mode and using single dc source. [ABSTRACT FROM AUTHOR]

This paper presents a neutral-point deviation and ripple compensating control method applied to a three-level neutral-point-clamped (NPC) converter. The neutral-point deviation and its harmonic components are analyzed with a focus on the average current flowing through the neutral-point of the dc link. This paper also proposes a control scheme compensating for the neutral-point deviation and dominant harmonic components under generalized unbalanced grid operating conditions. The positive and negative sequence components of the switching functions and ac input currents are employed to accurately explain the behavior of three-level NPC converter. Simulation and experimental results are presented to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

A high-frequency high voltage gain discontinuous conduction mode coupled-inductor boost LED driver based on planar component is presented in this paper. GaN switch is adopted with lower conducting resistance and higher switching speed. Zero voltage switching (ZVS) is achieved at the same time to reduce high switching loss caused by high switching frequency. Compared with the previous work, the voltage gain is higher and efficiency is higher because of ZVS. This paper focuses on high efficiency; therefore, resonant gate driver is adopted and efficiency is increased by 0.6%. In terms of the coupled-inductor, planar component is used and parameter optimization is also proposed to realize lower loss, including wingding loss and fringing loss caused by the air gap. A 500 kHz 36 W prototype has been designed to demonstrate theoretical analysis. In addition, comparison of drive loss between the resonant gate driver used in this paper and conventional driver implemented by Si8271 is made, revealing advantages of the resonant driver. Obtained efficiency was up to 92.1% at full load. [ABSTRACT FROM AUTHOR]

In this paper, a single-inductor dual-output (SIDO) dc–dc converter is proposed. The significant feature of the proposed converter is feeding a constant power load in low-voltage side (LVS) port, where even feeding a variable load at LVS does not have any cross regulation to high-voltage side port with the desired approximation. Magnificently, both merits are obtained in open-loop manner, which is an outstanding characteristic in comparison with that of the existed converters. In this paper, soft commutation and soft switching of switches and diodes are investigated along with the aforementioned main novelty. Moreover, detailed theoretical analyses of the proposed SIDO dc–dc converter in continuous conduction mode are presented besides the comparisons with some other structures. Finally, theoretical analyses are verified through a 1500 W experimental prototype results. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

Reduced switch active phase converters (APC) are cost-effective solutions for running three-phase loads from single-phase grids. This paper proposes a novel auxiliary-capacitor-based APC (AC-APC) for this application. The combination of the topological location of the auxiliary capacitor and the control of the AC-APC reduces current stress on the semiconductor devices. In this paper, a selection criterion for the optimal auxiliary capacitor value is formulated to reduce the device currents in such a way that the overall efficiency is enhanced. This paper presents a comparative analysis of converter volt-ampere (VA) rating and device power loss for conventional H-bridge active front-end and inverter-based topology, APC, and AC-APC. To evaluate the efficacy of the proposed AC-APC, an experimental study is conducted on the APC and the AC-APC feeding a 3-hp three-phase induction motor. At a full load of $\text{2.5}\,\text{kW}$ and $\text{0.8 } \text{power factor}$ , the measured maximum efficiency of the AC-APC is $2\%$ higher than that of the APC. Analytical evaluation of converter currents and device power loss are in close agreement with experimental observations. [ABSTRACT FROM AUTHOR]

This paper presents a balancing algorithm for the so-called Director Switch, a controlled, reverse conducting, self-powered, high-voltage switch, using series-connected insulated gate bipolar transistors (IGBTs). This is a key component on two new voltage-source, high-voltage direct current (HVDC) converter topologies. These, which promise efficiency, cost, and size reductions, are an alternate arm converter and a series bridge converter. One of the main design challenges of the director switch is how to supply the IGBT gate drivers, and other auxiliary electronics while overcoming the high-voltage insulation barrier to ground level. In this paper, this is achieved by using the energy stored in a capacitive clamp snubber circuit, which also helps with the overvoltage mitigation during rare hard-switching events. However, the clamp capacitor and by proxy the IGBT voltages become highly unbalanced during operation, compromising the integrity of the switch. This paper presents a balancing strategy that consists in applying a controlled delay in the switching of the IGBT levels, in a way that forces a voltage balance on all the switch levels. The paper explains the unbalance. Then, the balancing strategy is explained and validated on simulation and on a high-voltage experimental rig, on switches comprising two and three series-connected IGBTs, respectively. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

In low-power applications of photovoltaic (PV) systems, the transformerless grid-connected inverters have been preferred to increase the efficiency and reduce the cost, size, and power losses when they are compared to the ones with the transformer. A transformerless single-phase inverter topology with a single dc-link capacitor for the grid-connected PV systems is proposed in this paper. The proposed inverter has been simulated by using a cooperation process of the MATLAB and SPICE package programs and it has been implemented for experimental verification. The proposed inverter reduces the high-frequency common-mode leakage current caused by parasitic capacitances of PV panels, whereas it is controlled with the unipolar sinusoidal pulsewidth modulation. Also, the results show that the common-mode voltage remains constant. The efficiency of the proposed inverter has been compared to that of the most common topologies having the dc-link decoupling during the zero voltage states. This paper is accompanied by a video file demonstrating the power loss distribution in the inverter. [ABSTRACT FROM AUTHOR]

Aging of power system assets challenges utilities to maintain reliable service while minimizing their maintenance costs. Although malfunction of devices in the transmission or distribution networks can have catastrophic consequences, their failure is seldom unforeseen. Typically, the device aging occurs gradually over time until its health condition reaches a point of complete breakdown. The overall objective of this paper is to devise a non-invasive, online condition monitoring technique of circuit switchers for shunt capacitor banks. It aims to detect abnormal operation of these devices based on features derived from raw voltage and current waveforms, such that a predictive maintenance strategy may be employed before a complete failure occurs. The data analyzed in this paper are collected at a transmission capacitor bus, where the banks are equipped with pre-insertion impedance. Through a baseline range of values for selected parameters, the proposed technique is able to detect missing pre-insertion impedance during the capacitor energizing and failure of pre-insertion impedance switch out a few cycles after the energizing operation. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

This paper studies the high power density bidirectional dc–dc converter with interleaving, soft-switching, and near critical conduction mode (near-CRM) operation. Systematic design and control methods are proposed to enhance the effectiveness of passive currents balancing between multiple interleaved phases without using individual phase current feedbacks. This paper first analyzes the zero voltage turn-on operation, including the turn-off energy diversion by the added snubber capacitor and the turn-off resonance models. Second, the intrinsic inverse co-relation between the phase current deviation and the resulting effective duty cycles variation is quantitatively formulated and modeled as a closed-loop mechanism that balances the currents passively. Then, the design constraints of the system parameters including the snubber capacitance, dead time, and valley currents of the near-CRM mode are formulated to guarantee the effectiveness of counteracting the current unbalance. Finally, a variable switching frequency control is proposed to actively control the valley current and maintain the current balancing effectiveness throughout the operating range. An IGBT-based 20-kW three-phase interleaved prototype with the maximum efficiency of 99.1% is constructed to verify the proposed design and control methods. [ABSTRACT FROM AUTHOR]

This article develops a series of improved Z-source dc–dc converters to realize additional voltage pumping and high power density through two propositions. Proposition 1 develops two improved positive- and negative-connected Z-source dc–dc converters (IPZSC and INZSC), using the same number of components as in the existing voltage pumping Z-source converter. Based on Proposition 1, Proposition 2 proposes four novel embedded Z-source dc–dc converters (EZSCs) by placing the source in a specifically designed position, which realizes lower voltage stresses across capacitors. Various technical aspects of the proposed EZSCs, including operations, power losses, and small signal stability analyses are detailed in this paper. Besides, comparisons between the proposed series of improved Z-source dc–dc converters and other existing Z-source dc–dc converters are thoroughly made to demonstrate the better performance of the EZSCs. Finally, experiments are conducted to well validate the effectiveness and superiority of the proposed converter circuits. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

An improved two-stage model predictive current control (MPCC) for three-phase three-level converters in the paper, which can simultaneously achieve common-mode voltage (CMV) reduction, effective dc-link capacitor voltage control, and decreased computational burden, is proposed. Compared to the other current control strategies, it has the capability of handling multiple control objectives and possesses a simple structure. Furthermore, it greatly reduces the CMV since the peak CMVs of all the candidate voltage vectors are constrained to be less than one sixth of the dc-link voltage. In addition, an optimal two-stage voltage vector selection mechanism is employed in the proposed method. It helps to significantly reduce the computational complexity. Simulation and experimental results are provided to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Conventionally, the converter of switched reluctance motor (SRM) is fed by the uncontrollable diode bridge rectifier (DBR), which leads to a low grid-side power factor (PF) and high current total harmonic distortion (THD). In this paper, an alternative solution for the grid-connected high-speed SRM drive system with improved PF is proposed. In the proposed drive system, the three-level active front end (AFE) is connected in cascade with the midpoint converter for SRM operation. A centralized strategy, which controls the AFE and SRM together, is proposed to govern the motor speed and grid-side PF by regulating the real power and reactive power of the system, respectively. Specifically, the real power, reactive power, and the voltage balancing of split capacitors are controlled by the model predictive directed power control (MP-DPC) algorithm, which significantly reduces the control complexity and guarantees the fast dynamic response. Consequently, satisfying speed regulation, high PF, low current THD, and bi-directional power-transfer capability are achieved. An idea-proofed testbench is constructed in laboratory, and the applicability of the proposed drive system is verified by a series of experimental results. [ABSTRACT FROM AUTHOR]

With increasing penetration of solar PV, some distribution feeders are experiencing highly variable net-load flows and even reverse flows. To optimize distribution systems under such conditions, the scheduling of mechanical devices, such as OLTCs and capacitor banks, needs to take into account forecasted solar PV and actual grid conditions. However, these legacy switching assets are operated on a daily or hourly timescale, due to the wear and tear associated with mechanical switching, which makes them unsuitable for real-time control. Therefore, there is a natural timescale-separation between these slower mechanical assets and the responsive nature of inverter-based resources. In this paper, we present a network admissible convex formulation for holistically scheduling controllable grid assets to position voltage optimally against solar PV. An optimal hourly schedule is presented that utilizes mechanical resources to position the predicted voltages close to nominal values, while minimizing the use of inverter-based resources (i.e., DERs), making them available for control at a faster time-scale (after the uncertainty reveals itself). A convex, inner approximation of the OPF problem is adapted to a mixed-integer linear program that minimizes voltage deviations from nominal (i.e., maximizes voltage margins). The resulting OPF solution respects all the network constraints and is, hence, robust against modeling simplifications.Simulation based analysis on IEEE distribution feeders validates the approach. [ABSTRACT FROM AUTHOR]

Isolated, zero-voltage-switching dc–dc converter topologies represent attractive solutions in the continuous run toward higher switching frequencies, allowing more compact power supplies. Among them, the asymmetrical half-bridge flyback converter represents an interesting option, featuring simple duty-cycle control at constant switching frequency, as opposed to the popular LLC converter. The majority of papers dealing with this topology consider an approximated voltage gain similar to that of an isolated buck converter operating in continuous conduction mode, i.e., proportional to the duty cycle and, practically, load independent. On the contrary, the true voltage gain is nonmonotonic at high duty-cycle values. Anytime the converter is designed for a resonant operation, as is advisable to eliminate any reverse recovery problem of the rectifier diode, the voltage gain not only increases, but also becomes a function of the switching frequency. This article investigates the converter's voltage gain in detail, deriving a theoretical framework capable of capturing its real behavior and dependencies. The proposed analytical model has been verified through simulations as well as experimental measurements taken on a 160-W prototype working at 400 kHz. [ABSTRACT FROM AUTHOR]

DC transformer is an essential equipment for formation of multi-voltage-level DC grid. This paper proposes a novel non-isolated Boost-type alternate arm DC transformer (Boost-AADCT) for medium- and high-voltage level DC grid application. The Boost-AADCT is comprised of three submodule-cascaded arms, two thyristor-cascaded director switches, and two buffer capacitors. Bidirectional power transmission is achieved by alternatively charging and discharging of the intermediate arm following the Boost principle, while the pulsating power component caused by intermittent transmission is actively smoothened by grid-side buffer subcircuits formed by the buffer capacitors and grid-side arms. The active power buffering method increases the tolerance range of voltage ripple of the buffer capacitor, and the required energy storage capacity is resultantly reduced. Circuit configuration, operation principle, and mathematical model are first introduced. Then, the control strategy is proposed, the main circuit parameters are designed, and bidirectional fault-blocking capability is analyzed. Comparison with other DC-DC converters shows that the Boost-AADCT significantly reduces the requirement of semiconductors and has relatively lower synthetic cost. At last, performance of the Boost-AADCT and the proposed control strategies are evaluated by simulation tests conducted in MATLAB/Simulink environment. [ABSTRACT FROM AUTHOR]

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

Motors and inverters are increasingly being used in vehicles. As more vehicle components are being adopted, requirement for safety and installation space are increasing. Growing attention is being paid to the use of six-phase permanent magnet synchronous motors (PMSMs) and their parallel control by two inverters, because of their reduced size and enhanced safety. This paper proposes a pulsewidth modulation (PWM) control algorithm for a six-phase PMSM. In low-voltage vehicle components such as electric power steering, the current is usually acquired with resistors placed under the low-side switching devices. In the proposed control algorithm, the neutral voltage of the two inverters is shifted to either a lower or higher voltage within a certain range to allow for the signal conditioning time delay after the switching device turns on or off, and the time taken for the phase current to rise or settle. The paper proposes a novel PWM control algorithm that ensures that the on-time of the low-side switching devices satisfies the restriction on current sensing with resistors and reduces the current in the capacitor at the same time. The work contributes to reducing the current in a practical configuration involving low-voltage vehicle components. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper proposes a new developed switched-capacitor converter to achieve high-voltage pulses with adjustable voltage level and frequency. The proposed topology generates repetitive high-voltage pulses by using low-voltage power supply with reduced number of components, including power semiconductors and capacitor. Therefore, a converter based on switched-capacitor units with high voltage gain and high efficiency can be achieved. Operation principles and design steps of the converter as well as comparative study with conventional converters are described in this paper. Finally, simulation and experimental results of a two-stage structure of the proposed circuit validate the operation principles and features of this topology. [ABSTRACT FROM AUTHOR]

This paper analyzes the effects of shunt capacitors installed on the low voltage sides of 10/0.4 kV distribution transformers on the operation of these transformers. Using the results of an extensive measurement campaign, this paper compares: real and reactive power losses, secondary-side current, and primary-side apparent power before and after the installation of transformer capacitors. The following four cases of reactive power compensation are considered and discussed: adequate, conditionally adequate, and total compensation, as well as overcompensation. The presented analysis helps to identify transformer substations where the initial compensation should be changed or adjusted, in order to improve transformers’ operational performance. Voltage dependencies of real and reactive power demands of the transformer-supplied loads are taken into account, based on the previously identified load characteristics in the considered networks as well as voltage dependence of reactive power of shunt capacitors. The result with and without including these voltage dependencies in the analysis is compared and discussed. [ABSTRACT FROM AUTHOR]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]

This paper develops a modulation based fault-tolerant (FT) strategy for restoring the operation of three-phase modular multilevel converters (MMCs) with faulty switches. This FT strategy is based on a proposed modified space vector modulation (SVM) technique that generates balanced line-to-line (line) voltages even in the case of a fault occurrence. In the postfault operation, the proposed strategy is able to restore the fundamental amplitude of the line to the neutral (load) voltages to that of the normal operation condition with a slightly increased voltage stress over the switches in the faulty phase. In this paper, first a brief background about MMCs and SVM technique is provided. Then, the proposed FT strategy and the modified SVM technique are presented. Finally, several simulation and experimental results are provided to validate operation of the proposed strategy. [ABSTRACT FROM AUTHOR]

This paper presents two capacitor voltage balancing (CVB) strategies for modular multilevel converter (MMC) applications. Both balancing schemes are based on model predictive control and are designed to efficiently solve a constrained optimal control problem, where the predicted capacitor voltage errors are included in the cost function with the demanded output voltage of a cluster being forced through an equality constraint. The first method proposed in this paper computes specific modulation indexes for each module using the explicit solution of a relaxed version of the original optimization problem. The second approach proposed in this paper reduces the complexity of the original problem by linearizing the objective function and using an optimal sorting network based on a greedy algorithm to solve this approximation. Considering the structures of both solution approaches, they are integrated into modulation schemes based on phase-shifted and level-shifted pulsewidth modulation algorithms, respectively. Experimental results obtained from a nine-cell single-phase MMC prototype demonstrate the good performance achieved with the proposed methodologies, as well as the implementation simplicity offered by the proposed CVB algorithms. [ABSTRACT FROM AUTHOR]

This paper presents a high-gain modular input-parallel output-series dc-dc converter for photovoltaic integration with medium-voltage dc grids. A new full-bridge zero-current-switching (FB-ZCS) converter proposed in this paper is used as a fundamental building block. Existing FB-ZCS converters utilize transformer leakage inductance and a shunt-connected resonant capacitor for achieving smooth resonant current commutation and ZCS. The shunt-connected capacitor requires dedicated charging interval in every switching cycle and stores full-load-rated resonant energy at all load/input conditions, resulting in significant duty-cycle loss. Moreover, it suffers from energy leakage through transformer winding and requires overrating. All these factors adversely impact the operation range of the converter, which is important for achieving a wide maximum power point tracking range. Novel improvements in the proposed converter include minimization of duty-cycle loss and resonant capacitor leakage and the realization of the current-adaptive resonant energy storage mechanism, without using additional switches or auxiliary circuits. Operation of the proposed converter is presented and validated with simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dc power electronic transformer (DCPET) topology for locomotive, ac/dc hybrid grid, dc distribution grid, and other isolated medium-voltage and high-power applications. Compared with conventional PET topology, the proposed DCPET has fewer power semiconductor devices and high-frequency isolation transformers, which can improve the power density and reliability. Fault handling or redundancy design can be achieved to further improve the reliability when some dc–dc modules break down. Also, input voltage sharing control can be omitted to simplify the control system and improve the stability. Meanwhile, soft switching is guaranteed for all the switches, which is beneficial to increase switching frequency and improve power density. In this paper, the principle, evolution, and control of the proposed DCPET are respectively presented and studied in detail. Finally, a prototype of the proposed DCPET is built and the experimental results verify the validity and superiority of the proposed topology. [ABSTRACT FROM AUTHOR]

Enhancement of dc bus voltage utilization for a five-level inverter with single dc source and capacitor-fed H-bridge (CHB) units is investigated in this paper. A carrier-based modulation technique is used for boosting the dc bus utilization, which is established by providing detailed mathematical analysis. The five-level inverter used here is realized by cascading a CHB unit to each phase of a three-level neutral point clamped inverter. The increase in dc bus voltage utilization owes to the pole voltage redundancies offered by CHB units. The floating capacitors of H-bridge units are balanced within a quarter fundamental cycle using the switching state redundancies of pole voltage levels. The aforementioned modulation technique allows the inverter to enhance the dc bus utilization from 0.577 $\text{V}_{\text{dc}}$ to 0.63 $\text{V}_{\text{dc}}$ under unity power factor. This enhancement is obtained in the linear modulation range without increasing the dc bus voltage, and thus, the inverter can operate without the presence of low-order harmonics in its phase voltages. The strength of this paper lies in its detailed mathematical analysis for finding out the limiting modulation index and power factor condition in the light of floating capacitor voltage balancing issue. Simulation as well as experimental verification of the modulation scheme is carried out on an induction motor drive under various operating conditions. It is shown that this carrier-based modulation technique is suitable for any single source inverter topology with one CHB unit per phase. [ABSTRACT FROM AUTHOR]

This paper presents a new six-level flying capacitor based (FC-based) multilevel converter with one dc source and the capability of operating in all power factors and modulation indexes. Multilevel converters with one dc voltage source are attractive in many applications as they do not need rather expensive and bulky multiwinding input transformer connection at the dc side. On the other hand, not all classic multilevel converters with one dc source can produce any desirable number of output voltage levels at all power factors and/or modulation indexes. In this paper, a hybrid structure is proposed in which six voltage levels can be realized at the ac terminals. The modulation technique and the control strategy for the FC voltage balancing are presented. To show the advantages of the proposed converter, different performance criteria, such as switch count and rating, the size of capacitors, switching frequency, and power losses, are compared with other existing six-level topologies. The results indicate that the proposed structure is superior to other six-level converters from different standpoints. Simulation results are used to further evaluate the performance of the proposed converter. A laboratory-type experimental setup is used to validate the theoretical results. [ABSTRACT FROM AUTHOR]

In data center and telecommunication power supplies, the front-end dc–dc stage is required to operate with a wide input voltage range to provide hold-up time when ac input fails. Conventional LLC converter serving as the dc–dc stage is not suitable for this requirement, as the normal operation efficiency (at 400 V input) will be penalized once the converter is designed to achieve high peak gain (wide input voltage range). This paper examined the operation of the LCLC converter and revealed that the LCLC converter could be essentially equivalent to a set of LLC converters with different magnetizing inductors that are automatically adjusted for different input voltages. In nominal 400 V input operation, the LCLC converter behaves like an LLC converter with large magnetizing inductor, thus the resonant current is small. In the hold-up period, when the input voltage reduces, the equivalent magnetizing inductor will reduce together with switching frequency reducing, thus the converter achieves high peak gain. In this paper, a new design methodology is also proposed to achieve optimal utilization of the two resonant capacitors for high power application. To verify the effectiveness of the LCLC converter for hold-up operation, comprehensive analysis has been conducted; a detailed step by step design example based on capacitor voltage stress is introduced; an experimental LCLC prototype optimized at 400 V, with input voltage range of 250–400 V and 12 V/500 W as output has been presented. [ABSTRACT FROM AUTHOR]

A single-stage three-phase ac–ac converter benefiting from a high-frequency alternating link voltage is proposed in this paper. In this converter, a very small film capacitor can transfer the energy from the input to the output, owing to the high-frequency alternating voltage of the link. This eliminates the need for large electrolytic capacitors that are typically used in dc-link ac–ac converters. Moreover, a compact high-frequency transformer at the link can replace the bulky low-frequency transformers, in case isolation is required. These features increase the power density as well as reliability of the proposed converter in comparison with the conventional dc-link converters. The number of required switches in the proposed converter is 12, which is less than the number of switches needed in matrix converters, leading to lower switching and conduction losses. Despite being single-stage, the proposed ac–ac converter is capable of both stepping up and stepping down the voltage and also frequency transformation. This eliminates the need for using cascaded power converters. In this paper, the operation principles of the proposed ac–ac converter are investigated, and variable switching frequency and fixed switching frequency control methods for operating this converter are introduced. The performance of the converter is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]