Search

Multilevel inverters (MLIs) are playing a pivotal role in the power sector with potential applications, such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost, and higher efficiency compared with their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level voltage-source inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the dc-link capacitors and FCs. The generation of various output voltage levels and the limitation of the sinusoidal pulsewidth modulation control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared with the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

The integration of switched-capacitor techniques into multilevel inverters (MLIs) with a dc source string contributes to the boosting of voltage gain, renders it particularly attractive in reducing the number of input dc sources in the series string. However, the recent two-stage MLI topologies suffer from high voltage stress across the backend H-bridge. Addressing this concern, an improved topology, namely the one-switched-capacitor integrated MLI (1SCI-MLI) is proposed in this paper. An extended topology of 1SC-MLI is also established by appropriate incorporation of another switched-capacitor circuit. The two proposed topologies are endowed with voltage boosting capability. They also feature low switch count and low number of dc sources. More importantly, they resolve the high voltage stress problem in the existing counterparts. Their corresponding operational analysis and comparisons with recent MLI topologies are discussed. Simulation and experimental results from a laboratory prototype are presented to validate the effectiveness of the proposed topologies. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

In this paper, a new space vector pulse width modulation method to extend the linear modulation range of a cascaded five level inverter topology with a single dc supply is presented. Using this method, the inverter can be controlled linearly and the peak phase fundamental output voltage of the inverter can be increased from 0.577 to 0.637 V\text{dc} without increasing the dc bus voltage and without exceeding the induction motor voltage rating. This new technique makes use of cascaded inverter pole voltage redundancy and property of the space vector structure for its operation. Using this, the induction motor drive can be operated till the full speed range (0–50 Hz) with the elimination of lower order harmonics in the phase voltage and phase current. The five-level topology presented in this paper is realized by cascading a two-level inverter and two full bridge modules with floating capacitors. The inverter topology and its operation for extending the modulation range is analyzed extensively. Simulation and experimental results for both steady-state and dynamic operating conditions are presented in this paper. [ABSTRACT FROM AUTHOR]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

Cascaded multilevel inverter (CMI) is one of the most popular multilevel inverter topologies. This topology is synthesized with some series-connected identical H-bridge cells. CMI requires several isolated dc sources which brings about some difficulties when dealing with this type of inverter. This paper addresses the problem by proposing a switched-capacitor (SC)-based CMI. The proposed topology, which is referred to as switched-capacitor single-source CMI (SCSS-CMI), makes use of some capacitors instead of the dc sources. Hence, it requires only one dc source to charge the employed capacitors. Usually, the capacitor charging process in a SC cell is companied by some current spikes which extremely harm the charging switch and the capacitor. The capacitors in SCSS-CMI are charged through a simple auxiliary circuit which eradicates the mentioned current spikes and provides zero-current switching condition for the charging switch. A computer-aid simulated model along with a laboratory-built prototype is adopted to assess the performances of SCSS-CMI, under different conditions. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

Reliability of power inverters is of dominant importance in various applications, including industrial, military, aerospace, and commercial applications. Therefore, developing fault tolerant (FT) power inverters is extremely needed from the viewpoints of system availability and avoiding harmful consequences. Tolerating various types of faults, preserving full output ratings after the fault, and being cost-effective represent the main challenges for most of existing FT solutions. In this paper, a new FT single-phase five-level inverter topology is proposed. The proposed topology can effectively tolerate both of single or multiple switches faults whether they are of open- or short-circuit fault types. Moreover, the proposed topology does not deteriorate system efficiency in postfault operation compared to the previously developed FT solutions. Evaluation of the effectiveness and robustness of the proposed topology is verified in both of simulation and experimental environments. Different case studies are investigated in order to cover various types and locations of switches’ faults. Moreover, comprehensive comparisons are provided to validate the superiority of the proposed topology over the previously addressed techniques. [ABSTRACT FROM AUTHOR]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

This paper proposes a switched-capacitor multilevel inverter for high-frequency ac power distribution systems. The proposed topology produces a staircase waveform with higher number of output levels employing fewer components compared to several existing switched-capacitor multilevel inverters in the literature. This topology is beneficial where asymmetric dc voltage sources are available, e.g., in case of renewable energy farms based ac microgrids and modern electric vehicles. Utilizing the available dc sources as inputs for a single inverter solves the major problem of connecting several inverters in parallel. Additionally, the need to stack voltage sources, like batteries or supercapacitors, in series which demand charge equalization algorithms, are eliminated as the voltage sources employed share a common ground. The inverter inherently solves the problem of capacitor voltage balancing as each capacitor is charged to the value equal to one of the input voltage every cycle. State analysis, losses, and the selection of capacitance are examined. Simulation and experimental results at different distribution frequencies, power levels, and output harmonic content are provided to demonstrate the feasibility of the proposed multilevel inverter topology. [ABSTRACT FROM PUBLISHER]

This paper discusses the use of a cascaded multilevel converter for flexible power conditioning in smart-grid applications. The main feature of the proposed scheme is the use of independent dc links with reduced voltages, which makes such a topology an ideal candidate for medium- and high-power applications with increased reliability. The developed control strategy regulates independent dc-link voltages in each H-bridge cell, and allows the selective and flexible compensation of disturbing currents under a variety of voltage conditions without requiring any reference frame transformation. The selective control strategies are based on the decompositions proposed in the conservative power theory, which result in several current-related terms associated with specific load characteristics. These current components are independent of each other and may be used to define different compensation strategies, which can be selective in minimizing particular effects of disturbing loads. Experimental results are provided to validate the possibilities and performance of the proposed control strategies, considering ideal and deteriorated voltage conditions. [ABSTRACT FROM PUBLISHER]

A systematic method to derive the topologies of dual-input (DI) dual-buck inverter (DBI) is proposed in this paper. A family of DI-DBIs is harvested by replacing the buck switching bridges in a traditional DBI with DI pulsating voltage-source cells. In comparison with the traditional DBIs, an additional dc-input port for a low voltage energy source interface is introduced into the inverters. With the extended low-voltage dc-input port, a low-voltage dc source, whose voltage is lower than the peak amplitude of the ac output voltage, is able to supply power to the ac output within single-stage power conversion stage. The conversion stages of the dc /ac power system, the power rating and power losses of the front-end Boost converter of the inverter are reduced. Besides, the voltage stresses and switching losses of the power switches are reduced due to the multi-level characteristics of the proposed DI-DBIs. As a result, the conversion efficiency of the inverter and the overall dc/ac converter is improved effectively. A DI-DBI proposed, named as DB6 inverter, is analyzed in-depth as an example and compared with the traditional DBI to verify the effectiveness and advantages of the proposed method. [ABSTRACT FROM PUBLISHER]

This paper proposes a new nine-level inverter for medium- and high-power applications. The proposed topology comprises of a three-level (3L) active neutral-point-clamped (ANPC) inverter connected in series with a floating capacitor (FC) fed H-bridge. Besides, two additional switches operating at line frequency are appended across the dc link of the 3L ANPC structure. Compared with conventional hybrid cascaded inverters, the primary advantage of this addition is doubling of the resulting root mean square output voltage. This amelioration is achieved while preserving the standard 3L ANPC and H-bridge structures with minimum topological modification. A simple logic-gate-based voltage balancing scheme is developed to regulate the FC voltage. The proposed voltage balancing method is independent of load power factor, inverter modulation index, and can balance the voltage across FC instantaneously. The step-by-step formulation of logical expressions for the generation of gating pulses is deliberated in detail and can be generalized for any $n$-level inverter. Further, simulation results as well as the experimental measurements obtained from the laboratory prototype are presented to validate the effectiveness and practicability of the proposed configuration. Finally, the notable merits of the proposed inverter over the prior art topologies is established through a comprehensive comparative study. [ABSTRACT FROM PUBLISHER]

Multilevel inverters are receiving more attentions nowadays as one of preferred solutions for medium- and high-power applications. As one of the most popular hybrid multilevel inverter topologies, the five-level active-neutral-point-clamped inverter (5L-ANPC) combines the features of the conventional flying-capacitor type and neutral-point-clamped (NPC) type inverter and was commercially used for industrial applications. In order to further decrease the number of active switches, this paper proposes a seven-switch 5L-ANPC (7S-5L-ANPC) topology, which employs only seven active switches and two discrete diodes. The analysis has shown a lower current rating can be selected for the seventh switch under high power factor condition, which is verified by simulation results. The modulation strategy for 7S-5L-ANPC inverter is discussed. A 1 kVA single-phase experimental prototype is built to verify the validity and flexibility of the proposed topology and modulation method. [ABSTRACT FROM AUTHOR]

In this paper, a new cascade switch-ladder multilevel inverter topology is presented which can generate a large number of output voltage levels. First, a fundamental switch-ladder multilevel inverter structure is described. Then, the structure of recommended cascade topology based on series connection of fundamental switch-ladder topologies is presented. To generate maximum number of levels with minimum number of switching elements, dc sources, and voltage on switches, the proposed cascade topology is optimized. Comparison results prove that the presented cascade topology requires fewer numbers of components. Also, the value of voltage rating on switches is less than other structures. Experimental results for two topologies are analyzed to verify the performance of the proposed topology. [ABSTRACT FROM PUBLISHER]

This paper presents a nine-level inverter topology for an open-end induction motor drive requiring only eight switches per phase, using two three-level inverters with two isolated dc links in a 3:1 ratio. A space-vector-based formulation is used to determine pole voltages such that both inverters supply power to the load over the full modulation range, eliminating the possibility of dc bus overcharging. Proper selection of switching states ensures that all floating capacitor voltages are kept tightly balanced. A digital state machine is used to select sequences of switching states in order to eliminate deadtime-induced pole voltage transients, further improving the output-voltage quality. A level-shifted carrier-based pulse width modulation scheme is used. The steady-state and transient performance of this topology were verified and the experimental results are included. [ABSTRACT FROM AUTHOR]

A novel flying-capacitor-clamped five-level inverter based on bridge modular switched-capacitor topology is proposed in this paper. The inverter features the switched-capacitor circuit with dc–dc boosting conversion ability and the multilevel inverter circuit with flying-capacitor-clamped performance. With the special composite structure, the number of components is cut down compared to the topology of the conventional cascaded multilevel inverter. Meanwhile, part of switches can be operated under line voltage frequency, resulting in switching loss reduction. Hence, the potential of system efficiency and power density is released due to embed switched-capacitor circuit. More importantly, the optimized carrier-based phase disposition pulse width modulation method is employed as a control strategy. Under this control strategy, the capacitor voltage self-balance can be realized and quality of output waveforms can be improved significantly. After simulation, the prototype is built to validate the correctness and practicability of the analysis. [ABSTRACT FROM AUTHOR]

This paper presents a closed-loop space vector modulation (SVM)-based sliding mode controller (SMC) for a three-level grid-connected neutral point clamped (3L-NPC) inverter. The nonlinear SMC based on Gao's reaching law has been designed to control the grid current and inject desired amount of active and reactive power into the network. Due to using single dc source at the NPC inverter dc bus, neutral point voltage is controlled through redundant switching states and instantaneous dc voltage feedback integrated into SVM technique. Meanwhile, there is no external voltage controller involved, thus no associated fine tuning issues are existed. The performance of the proposed hybrid controller to inject a desired active/reactive power to the grid is investigated through external perturbations such as change in the line current amplitude/phase shift, ac voltage fluctuation, as well as dc voltage variation. Full converter state-space model was developed and simulated. Experimental results are provided to verify the fast dynamic performance, low content of line current THD%, and good voltage balancing of dc bus capacitors of the NPC inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology of six-level inverters for a medium-voltage high-power applications is proposed, which consists of inner flying-capacitor inverter (FCI) units and outer two-level inverter units. The proposed topology can reduce the number of devices, components, and isolated sources compared with the existing ones in the case of the same number of output voltage steps, which result in a reduction of the size and weight of the inverters. Also, the total power loss of the proposed topology is lower than that of the diode-clamped inverter (DCI) and FCI. Besides, the estimated cost of the proposed topology is about 60.5% and 81.3% compared with the DCI and FCI, respectively. In addition, the modulation technique and the control strategy for the dc-link capacitor and flying-capacitor voltages are developed for the proposed topology. The effectiveness of the proposed six-level inverter for the medium-voltage applications has been verified by simulation results. Also, the feasibility of the proposed inverter has been proved by experimental results for the prototype at the laboratory. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

For cascaded multilevel inverter topologies with a single dc supply, closed-loop capacitor voltage control is necessary for proper operation. This paper presents zero and reduced common-mode voltage (CMV) operation of a hybrid cascaded multilevel inverter with predictive capacitor voltage control. Each phase of the inverter is realized by cascading two- three-level flying capacitor inverters with a half-bridge module in between. For the presented inverter topology, there are redundant switching states for each inverter voltage levels. By using these switching state redundancies, for every sampling instant, a cost function is evaluated based on the predicted capacitor voltages for each phase. The switching state that minimizes cost function is treated as the best and is switched for that sampling instant. The inverter operates with zero CMV for a modulation index upto 86%. For modulation indices from 86% to 96%, the inverter can operate with reduced CMV magnitude (Vdc/18) and reduced CMV switching frequency using the new space-vector pulsewidth modulation (SVPWM) presented herein. As a result, the linear modulation range is increased to 96% as compared to 86% for zero CMV operation. Simulation and experimental results are presented for the inverter topology for various steady state and transient operating conditions by running an induction motor drive with open loop $V/f$ control scheme. [ABSTRACT FROM PUBLISHER]

In this paper, initially a new dc/dc converter is proposed which can produce boosted multiple dc link voltages by using the novel switched-capacitor converter (SCC) and with reduced number of switches. In the proposed SCC, voltage of all capacitors is charged by binary asymmetrical pattern as self-balancing and without using any auxiliary circuits. The proposed SCC will boost the input dc power supply voltage without transformer by switching the capacitors in series and in parallel. Next, a new single phase switched-capacitor multilevel inverter (SCMLI) topology which uses the proposed SCC units as virtual dc links have been proposed. The proposed topologies reduce the number of power switches, diodes, isolated dc power supplies, size, and the cost of the system in comparison with conventional similar topologies. For example, by contribution of proposed SCMLI structure, 49 and 137 output voltage levels are made by only 14 and18 power switches and 3 and 4 isolated dc power supplies, respectively. To confirm the performance of proposed topology, various simulation results by PSCAD/EMTDC software and experimental tests are given. [ABSTRACT FROM AUTHOR]

In this paper, a new cascaded nonlinear controller has been designed and implemented on the packed U-cell (PUC) seven-level inverter. The proposed controller has been designed based on a simplified model of PUC inverter and consists of a voltage controller as an outer loop and a current controller as an inner loop. The outer loop regulates the PUC inverter capacitor voltage as the second dc bus. The inner loop is in charge of controlling the flowing current, which is also used to charge and discharge that capacitor. The main goal of the whole system is to keep the dc capacitor voltage at a certain level results in generating a smooth and quasi-sine-wave seven-level voltage waveform at the output of the inverter with low switching frequency. The proposed controller performance is verified through experimental tests. Practical results prove the good dynamic performance of the controller in fixing the PUC capacitor voltage for various and variable load conditions and yet generating low-harmonic seven-level voltage waveform to deliver power to the loads. Operation as an uninterruptible power supply (UPS) or ac loads interface for photovoltaic energy conversion applications is targeted. [ABSTRACT FROM AUTHOR]

In this paper, a model-predictive control (MPC) has been designed and implemented on the packed U-cell (PUC) inverter, which has one isolated dc source and one capacitor as an auxiliary dc link. The MPC is designed to regulate the capacitor voltage at the desired magnitude to have seven voltage levels at the output of the inverter. Since grid-connected application is targeted by this application, the inverter should be capable of supplying requested amount of active and reactive power at the point of common coupling (PCC) as well. Therefore, MPC should also consider the line-current control to monitor the exchange of reactive power with the grid while injecting appropriate active power at low total harmonic distortion (THD). Various experimental tests including change in dc-source voltage, active power variation, and operation at different power factor (PF) have been performed on a laboratory prototype to validate the good performance obtained by the proposed MPC. The dynamic performance of the controller during sudden changes in dc capacitor voltage, supply current, and PF demonstrates the fast and accurate response and the superior operation of the proposed controller. [ABSTRACT FROM PUBLISHER]

This paper proposes three dynamic voltage restorer (DVR) topologies. Such configurations are able to compensate voltage sags/swells in three-phase four-wire (3P4W) systems under balanced and unbalanced conditions. The proposed systems use two independent dc links. Proposed configurations present advantages in terms of switch blocking voltages and consequently lower dc-link voltage rating. The complete control system, including the pulsewidth modulation (PWM) technique, is developed, and comparisons between the proposed configurations and a conventional one are performed. Simulation and experimental results are provided to validate the theoretical approach. [ABSTRACT FROM AUTHOR]

A capacitor voltage-balancing method for a nested neutral point clamped (NNPC) inverter is proposed in this paper. The NNPC inverter is a newly developed four-level voltage-source inverter for medium-voltage applications with properties such as operating over a wide range of voltages (2.4–7.2 kV) without the need for connecting power semiconductor in series and high-quality output voltage. The NNPC topology has two flying capacitors in each leg. In order to ensure that the inverter can operate normally and all switching devices share identical voltage stress, the voltage across each capacitor should be controlled and maintained at one-third of dc bus voltage. The proposed capacitor voltage-balancing method takes advantage of redundancy in phase switching states to control and balance flying capacitor voltages. Simple and effective logic tables are developed for the balancing control. The proposed method is easy to implement and needs very few computations. Moreover, the method is suitable for and easy to integrate with different pulse width modulation schemes. The effectiveness and feasibility of the proposed method is verified by simulation and experiment. [ABSTRACT FROM PUBLISHER]

Nowadays, use of multilevel inverters in high-power applications clearly can be seen. High quality and lower distortion of the output voltage and low blocking voltage of semiconductor switches are being presented as the major privileges of the multilevel inverter compared to the traditional voltage source inverter. In this paper, a new topology of multilevel inverter is proposed as fundamental block. The proposed topology is generalized using series connection of the fundamental blocks. The proposed multilevel inverter has been analyzed in both symmetric and asymmetric operation modes. A great perfection in voltage levels number with minimum switching devices has been obtained in both symmetric and asymmetric modes. Thereafter, a detailed study of losses and peak inverse voltage (PIV) of the proposed multilevel inverter is given. Also, in continuation, a comparison between the proposed topology and the traditional one and a recently developed topology is carried out. Finally, a computer simulation using MATLAB/Simulink is presented and a laboratory prototype implementation verifies the results. [ABSTRACT FROM AUTHOR]

In this paper, a new configuration of a three-phase five-level multilevel voltage-source inverter is introduced. The proposed topology constitutes the conventional three-phase two-level bridge with three bidirectional switches. A multilevel dc link using fixed dc voltage supply and cascaded half-bridge is connected in such a way that the proposed inverter outputs the required output voltage levels. The fundamental frequency staircase modulation technique is easily used to generate the appropriate switching gate signals. For the purpose of increasing the number of voltage levels with fewer number of power electronic components, the structure of the proposed inverter is extended and different methods to determine the magnitudes of utilized dc voltage supplies are suggested. Moreover, the prototype of the suggested configuration is manufactured as the obtained simulation and hardware results ensured the feasibility of the configuration and the compatibility of the modulation technique is accurately noted. [ABSTRACT FROM AUTHOR]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

In this paper, a new general cascaded multilevel inverter using developed H-bridges is proposed. The proposed topology requires a lesser number of dc voltage sources and power switches and consists of lower blocking voltage on switches, which results in decreased complexity and total cost of the inverter. These abilities obtained within comparing the proposed topology with the conventional topologies from aforementioned points of view. Moreover, a new algorithm to determine the magnitude of dc voltage sources is proposed. The performance and functional accuracy of the proposed topology using the new algorithm in generating all voltage levels for a 31-level inverter are confirmed by simulation and experimental results. [ABSTRACT FROM PUBLISHER]