Search

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a different Finite Control Set – Model Predictive Control (FCS-MPC) for grid-connected three-phase bidirectional power inverters. These are typically used in dc or ac renewable-based microgrids (MGs), where bidirectional operation and fast dynamic response is required. The bidirectional grid-connected inverters are an essential part of MG, which inject energy into the ac grid or demand energy from it. The dynamic behavior of the system is a major concern since the current can suddenly change depending on the hierarchical controller. This paper proposes a different cost function using sliding mode theory, which offers a good dynamic response, reduced computational burden, and a parameter-free control model. The operation principle of the proposed controller is given and evaluated using a Hardware-In-the-Loop (HIL) system, but also experimentally with a 1kW laboratory prototype. The final results demonstrate the advantages of using this approach in grid-connected three-phase bidirectional power inverters in terms of dynamic response and reduced computational burden, making this solution technically attractive and viable. [ABSTRACT FROM AUTHOR]

Conventional model predictive control (MPC) for three-level active neutral point clamped converter (ANPC) utilizes weighting factors to achieve the optimal control of multiple control objectives in a single cost function. However, the selection of these weighting factors has an impact on the performance of the controlled objectives significantly. Tuning of weighting factors is usually tedious and lacks theoretical background. Moreover, the predictive and evaluation process for multiple objectives optimization have to be carried out by enumerating all admissible switching states within one loop. To simplify the complexity of this process and eliminate the effect of weighting factors, this paper proposes a cascaded predictive control scheme for a 3L-ANPC inverter fed induction machine (IM) drive. With the proposed approach, three separate cost functions for three control objectives, stator flux vector, neutral point voltage and device loss distribution are evaluated in a cascaded way, so that the optimization of these control objectives is performed independently. A 3L-ANPC inverter driven IM drive is studied in this paper to verify the effectiveness of the proposed algorithm. Experimental results in different operating conditions confirm that the proposed method achieves satisfactory steady-state and transient performances comparable to the conventional predictive control approach. The weighting factors used in the conventional method are eliminated and the computational effort is reduced by 68% compared to the conventional method without any sacrifice in the drive performance. [ABSTRACT FROM AUTHOR]

The safety of converters is key to the stable operation of AC/DC hybrid power grids after AC faults. Thyristor valve current is a direct manifestation of the converter observability, but there are no measuring elements inside the converter, so the thyristor valve current can be reflected only indirectly through external electrical quantities. This paper proposes a virtual measurement scheme based on the temporal features of the converter terminal current. First, under the action of the trigger pulse, the polarity characteristics of the AC current and temporal features between the valves are utilized to predictive estimate the valve state. Then, when commutation failures occur and the bypass paths form, the conduction state of valve is constructed based on the relationship between AC and DC current. Last, when the valve is to be shut-off in the bypass path, the blocking state of the valve is corrected based on the unidirectional conductance characteristics of the valve. According to the above analysis, combined with the topological current equation of the converter, the valve current can be calculated in the whole process. Through the simulation of the different valve states and bypass paths and analysis of the field record data, the results show that the valve current can still be accurately calculated based on the virtual measurement scheme. [ABSTRACT FROM AUTHOR]

Most microgrid protection schemes found in published literature suffer from a lack of generality in that they work well for the assumed topology, including type and placement of sources. Other generic protection schemes tend to be too complicated, too expensive, or both. To overcome these drawbacks, a topology-agnostic, scalable, and cost-aware protection based on fundamental principles that work in the presence of high penetration of inverter-based resources (IBRs) is developed and tested in this paper. The protection system also implements stable automatic reconfiguration of the healthy sections of the system after clearance of fault, thus increasing resilience by self-healing. To achieve this ambitious goal, stable inverter models are developed that operate in unbalanced networks in grid-connected and islanded modes, even with 100% IBRs, share power without conflicting controls, and can ride through faults while limiting fault currents. The scheme is tested for primary and backup protection and reconfiguration on the IEEE 123-node feeder in grid-connected and islanded modes with 15 IBRs connected to the system. [ABSTRACT FROM AUTHOR]

This paper proposes a new passive Islanding detection approach for the Inverter Interfaced Distributed Generators (IIDGs) operating under different control modes. First, a novel index is formulated using Root Mean Square (RMS) value of the voltage and the frequency information, acquired at the Point of Common Coupling (PCC) of the target DG. The index is then post-processed by estimating the number of peaks and valleys $(N_{p_{k}-v})$ in a cycle using the sliding window concept, which indicates the occurrence of an event. Finally, the nature of the event, i.e., Islanding or non-Islanding, is decided by exploiting the two statistical features viz., Square of RMS $(S_{RMS})$ of $N_{p_{k}-v}$ and Average Crest Factor $(ACF^{m})$ of the proposed index. The performance of the proposed method (P-IDM) is demonstrated through comprehensive studies in PSCAD/EMTDC for the single-bus and IEEE 34-bus Active Distribution System (ADS). Also, the real-time validation is performed for the IEEE 34-bus using Controller Hardware-in-the-Loop (CHIL) setup comprising of Real-Time Digital Simulator (RTDS) and dSPACE1104. The simulation and hardware results for different test systems indicate that the proposed scheme, being generic in nature, sustains its efficacy under various interface controls of IIDGs. Finally, a comparative assessment with the other existing Signal Processing (SP) based passive methodologies shows the supremacy of the proposed method in terms of accuracy and faster detection. [ABSTRACT FROM AUTHOR]

Line-commutated converters are extensively used as the interface between ac grids and classic HVDC systems. At the inverter side, commutation failure of switches is one of the most common faults that can pose threats to the system operation. Practical and reliable study of such phenomena relies on accurate and efficient converter models for simulations. Recently, a parametric average-value model (PAVM) has been presented for ac–dc rectifiers, which considers the internal faults of the converter. In this paper, the PAVM methodology is extended to the dc–ac inverter systems, including the commutation failure of switches. The proposed PAVM also augments an automatic fault detection technique to determine the faulty switches. Using comprehensive simulation studies, the developed model is verified to accurately predict the commutation failure of switches and reconstruct the waveforms consistent with the detailed switching models of inverters while being computationally more efficient. The proposed PAVM is envisioned to be an efficient and accurate asset for simulation of HVDC systems and inevitable when faults of switches need to be considered. [ABSTRACT FROM AUTHOR]

Miniaturization and low cost contribute to the development and popularization of wireless power transfer (WPT). Reducing the number of power conversion stages can reduce the volume and cost of the WPT converter, and even make it possible to improve the efficiency. A single-stage WPT converter with constant current (CC) and constant voltage (CV) output and its asymmetric modulation method are proposed in this paper. A direct AC-AC converter is applied to the primary side of the WPT converter to directly convert line-frequency AC to high-frequency AC. The applied direct AC-AC converter that can replace the commonly used multi-stage primary converter reduces the number of circuit devices, thereby reducing the volume and cost of primary converter. The proposed WPT converter can realize zero voltage switching (ZVS) and power factor correction (PFC). In order to achieve CC and CV output, a switchable hybrid compensation topology is applied to the proposed WPT converter. A 720-W experimental prototype was manufactured to verify the rationality of the proposed WPT converter and the correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a dual-hysteresis band control method for multi-drive systems based on a nine-switch inverter. The drive system contains two independent three-phase induction motors fed by a nine-switch inverter. Independent control of torque, speed, and stator current of two load stages is achieved. The proposed strategy offers a reliable control operation of both induction machines under individual load profiles. Instead of using independent sets of three-phase voltage source converters, the nine-switch inverter is used to drive separate machines. Thus, the volume and size of the power stage are noticeably reduced due to the use of fewer semiconductors. The theoretical concept and design steps of the proposed method are presented. The performance of the closed-loop independent motor control scheme is experimentally validated using a 3.2 kW lab-scaled nine-switch inverter prototype and Altera Cyclone IV Field-programmable gate array. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

In a line-commutated converter based high-voltage direct-current (LCC-HVDC) system, the inverter control system usually includes constant extinction angle (CEA) controller, constant current (CC) controller, current error controller (CEC), and voltage-dependent current order limiter (VDCOL). However, the interaction influence of multiple controllers may cause repetitive commutation failure (CF). For this purpose, this paper deeply investigates the mechanism and the influencing factors of repetitive CF caused by controller interaction. It is found that the lower limit value of CEA controller can affect the control switching process and thus the probability of repetitive CF. Besides, the minimum gamma measurement (MGM) unit prevents the system from acquiring the real extinction angle in time, which results in the DC current fluctuation during the recovery process. Moreover, the probability of control-induced repetitive CF is much higher when the HVDC inverter is connected to a weak AC system or the AC fault is not serious but not cleared in time. Based on the above analyses, an improved control method is proposed for recovery performance improvement, which is mainly realized by modifying the lower and upper limits of the CEA controller during recovery. Finally, the simulation and experimental results verify the theoretical analyses and the proposed control method. [ABSTRACT FROM AUTHOR]