Search

This paper describes a flow control of the dye in the paper mill with the quasi-Z-source indirect matrix converter (QZSIMC) fed induction motor drive. More than a decade the voltage-source inverter (VSI) and current-source inverter (CSI) have been used to control the speed of the induction motor, which in turns controls the flow of dye. Recently, the matrix converter (MC) has been an excellent competitor for the VSI or CSI for its compactness. The voltage transfer ratio of the VSI, CSI, and MC has been limited to 0.866. Thus, the efficiency of these converters is less. To improve the voltage transfer ratio the quasi-Z-source network (QZSN) is to be used between voltage source and indirect MC (IMC). The modification in the shoot-through duty ratio of the QZSN varies the voltage transfer ratio greater than 0.866. Different voltage transfer ratios are needed for different voltage sag conditions. For a variation of the duty ratio of the QZSN, the fuzzy logic controller has been presented. To control the IMC vector control with space vector modulation has been presented. This paper proposes the implementation of QZSIMC adjustable speed drive for the flow control of dye in paper mill during different voltage sag conditions. A 4-kW prototype has been built and the effectiveness of the proposed system is verified with simulation results and experimental setup. Simulation is done in MATLAB, Simulink platform. Experimental setup is done with the aid of a TMS320F2812 (Texas Instrument) processor. The experimental results validate the maintenance of the speed of an induction motor at the set condition, thus controlling the perfect flow of dye in paper manufacturing technology. [ABSTRACT FROM AUTHOR]

Supercapacitors have drawn numerous attentions in recent years since they can deliver relatively high power and energy densities. This article introduces an all-printed paper based surface mountable supercapacitor (SMS), which could withstand the reflow soldering process when integrated into microelectronic systems. The device was fabricated by screen printing and stencil printing processes, contributing to low cost and large-scale fabrication. Furthermore, building electronic devices on ubiquitous paper substrates had advantages of light weight, low cost, and eco-friendliness, etc. Based on activated carbon electrode material and ionic liquid electrolyte, the capacity of the supercapacitor could reach 14 mF at the device volume of 3.2 mm ? 2.5 mm ? 0.175 mm, besides, the specific volumetric capacity was superior than most of the commercial SMS devices. [ABSTRACT FROM PUBLISHER]

A capacitor formed of fluid-impregnated paper metalized on one side and a polymer film results in a relaxation peak caused by the much more rapid polarization of the dielectric fluid impregnated paper relative to the polymer film. This results in the capacitance being a function of frequency, with a substantial increase in capacitance at very low frequencies. A theory for such a capacitor is developed and compared with measurements on actual capacitors with relatively good agreement. The implications of the theory for discharge current and discharge efficiency are discussed. [ABSTRACT FROM AUTHOR]

The work reported in this paper aims at developing an algorithm for system operators to solve a robust security-constrained AC optimal power flow (R-SC-ACOPF) problem, which also optimizes the settings of discrete controllers including load tap changers (LTCs) and shunt capacitor banks (SCBs). An iterative algorithm involving a master problem and a number of sub-problems is proposed. The master problem selects the optimal discrete controllers’ settings by taking into account primal SC-ACOPF constraints based on the single-component worst contingencies identified by the sub-problems. Each sub-problem is a bi-level max-min problem used to find the current worst contingency. The overall objective is to minimize the total cost, including generation and load shedding cost, while satisfying all relevant constraints. The master problem and sub-problems allow representing LTC tap positions, SCB status, and contingencies using binary variables. Two case studies are presented as applications of this novel technique. [ABSTRACT FROM AUTHOR]

Presents a study that examined the aging process of mineral oil-impregnated-high density kraft paper capacitor bushing models subjected to voltage switching surges. Effects of the removal of electrical impulse stress over a finite time period; Thickness of the insulating system of the model capacitor bushing; Implication of the partial discharged inception stress characteristics for the doubled insulation specimen.

Focuses on the recovery voltage method (RVM), a method used to estimate the polarization spectrum in composite oil/paper insulation systems. Methods for determining dielectric insulation; Mathematical description of the recovery voltage method; Identification of the equivalent circuit using a model with a single polarization capacitor.

In recent years, there is an increased use of passive filters in both transmission and distribution systems due to the proliferation of power electronic devices. However, the problem of filter design has not been well addressed in the past and one example is the application of high-pass filters in a filter package. Three types of HP filters are widely used to mitigate multiple harmonics, i.e., 2nd HP filter, 3rd HP filter and C-type filter. There is still a lack of research to clearly reveal the characteristics of each filter, which makes it difficult for the designer to select the optimal filter topology under different circumstances. The main goal of this paper is to solve the problem of how to select a proper configuration among three HP filter candidates for a given harmonic problem. Unlike the conventional optimization-based filter studies, this paper investigates three HP filters in an analytical way. As a result, the paper provides a deep insight into the inherent characteristics of the filter and the conclusions drawn in the paper are universal; thus can be used in different applications, ranging from low voltage levels to high voltage levels. The research results lead to a recommended application scope of each HP filter, which is very useful to guide the design of filter packages and help designers to evaluate the design results. [ABSTRACT FROM AUTHOR]

This paper proposes an adaptive self-tuned current controller design for an LCL-filtered LC-tuned single-phase shunt hybrid active power filter (HAPF), which offers adaptability and flexibility of the control system to filter parameters changes. System modelling and online identification of parameters are presented. Then, a systematic self-tuned controller (STC) design is proposed to calculate the controller parameters and obtain the final control law adaptively. The exact HAPF parameters design is described and the overall closed-loop stability evaluation with considering digital control delay is discussed in this paper. To confirm the theoretical achievements, simulations and experimental tests on a real prototype system are performed. The results are in good accordance and demonstrate the effectiveness and superior performance of the suggested control technique. Furthermore, a comprehensive comparison between the proposed control technique and other controllers is provided to show the superiority of the proposed system from different aspects. [ABSTRACT FROM AUTHOR]

Conventional half bridge modular multilevel converter (MMC) system will suffer great over-current when there is a dc side fault. Therefore, topology study in sub-modules with dc side fault blocking capability have become one of the hotspots in MMC field. However, fault blocking topologies using conventional IGBT devices must employ more semiconductors than half bridge topology. The extra semiconductor devices employed in the topology will lead to the increase of cost and conduction loss. To reduce the conduction loss of the fault blocking topology, a novel sub-module topology is proposed in this paper. The proposed topology employs reverse blocking devices to form the low conduction loss path. Conduction loss analysis is conducted in this paper to show the priority of the proposed topology. Simulation and experiment results verified the dc fault blocking capability of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper analyzes the unsymmetrical operation of the dc/dc MMC caused by parametric uncertainty. The unsymmetrical operation is referred to as the condition in which parameters involved in ac power generation are not equal in the phase-legs of the converter. Because existing models in the literature cannot exhibit the unsymmetrical operation of the dc/dc MMC, new detailed and simplified steady-state models are developed in this paper. In the developed models, the connection between the operation of different phase-legs shows itself when the dc-link impedance is considered. Using the developed models, the parameters that can force the converter to operate in unsymmetrical conditions are identified, and the maximum variation that the converter can tolerate is found. It is shown that even a small parameter variation leads to the leakage of the ac circulating current into the dc-link, which is not acceptable. By conducting various case studies, the impacts of the dc-link length, the transmitted power, and the conversion ratio on the unsymmetrical operation of the dc/dc MMC are characterized. The results showed that the converter would be more sensitive to the parameter variation as these parameters increase. Comparative analysis and simulation results confirm the validity and effectiveness of the presented models and analysis method. [ABSTRACT FROM AUTHOR]

The paper addresses an improved inner current reference calculation to be employed in the control of modular multilevel converters operating during either balanced or unbalanced conditions. The suggested reference calculation is derived based on the AC and DC additive and differential voltage components applied to the upper and lower arms of the converter. In addition, the impacts caused not only by the AC network’s impedances but also by the MMC’s arm impedances are also considered during the derivation of the AC additive current reference expressions. Another issue discussed in this article regards that singular voltage conditions, where the positive-sequence component is equal to the negative one, may occur not only in the AC network but also internally (within the converter’s applied voltages). Several different inner current reference calculation methods are compared and their applicability during the former fault conditions is analyzed. The paper presents a detailed formulation of the inner current reference calculation and applies it to different unbalanced AC grid faults where it is shown that the presented approach can be potentially used to maintain the internal energy of the converter balanced during normal and fault conditions. [ABSTRACT FROM AUTHOR]

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

The capacitor condition monitoring is an important issue for the reliable operation of modular multilevel converters (MMCs) in high-voltage applications. The numerous capacitors make the monitoring for the capacitor condition complex and computation-consuming. This paper proposes a hierarchic capacitor condition monitoring strategy to assure the reliability of high-voltage MMCs. In the strategy, the switching times of the switching signals are counted to detect the condition of the capacitor in each submodule (SM). Then, the subsequent capacitance calculation method is only conducted to the abnormal capacitors indicated by the above condition detection algorithm. Meanwhile, the variations of the measured and reference capacitor voltages are employed to calculate the capacitance in the proposed method. The condition detection algorithm shrinks the scope where the abnormal capacitors locate, which avoids calculating the total capacitances in MMCs. In the proposed capacitance calculation method, the complex operations are further saved. Both the two measures reduce the computation burden effectively. The implementation of the whole monitoring strategy is simple and fit for high-voltage MMCs. Moreover, the strategy has no adverse influence on the normal operation of MMCs. The effectiveness of the proposed strategy is verified by the simulation studies with the professional tool Matlab/Simulink. [ABSTRACT FROM AUTHOR]

The risk of unstable subsynchronous oscillations (SSO) in DFIG-based wind parks radially connected to transmission lines with series capacitive compensation is typically assessed with numerous electromagnetic transient (EMT) simulations, which is a time-consuming process. However, not all operating scenarios present risk of SSO and require such a detailed investigation. This paper proposes two charts based on impedance equivalents of wind generators obtained through frequency scans to quickly map which combinations of parameters can create unstable SSOs and which combinations are risk-free. With the information, engineers can immediately filter out scenarios with no risk of instability and conduct detailed studies on fewer scenarios that are truly critical. These charts can be obtained with simple equations that use only information readily available in practice to engineers, without the need to run any computer simulation. The charts also reveal the key operating conditions that can increase the risk of an unstable SSO and provide real-time quantitative insights into how close a wind park is to an instability. Application examples are provided to illustrate how this approach can help engineers speed up studies to identify the risk of SSO. [ABSTRACT FROM AUTHOR]

A novel single-stage doubly grounded transformerless inverter configuration which can buck-boost the output voltage is proposed in this paper. In this transformerless inverter configuration grid neutral is directly connected to PV panel negative rail which suppresses/eliminates the PV leakage currents. In addition, the tracking of maximum power point is possible for wide variation of weather conditions due to buck-boost voltage capability of inverter. Moreover, the proposed inverter topology has symmetrical operation in both half cycles hence injects negligible DC offset current in to the grid. Here the symmetrical operation of inverter is achieved due to one inductor is used for both half cycles of the grid. The proposed topology is realized using five switches, two of which work at 50 Hz and remaining three switches at high frequency which reduces overall semiconductor losses. Further, the proposed inverter topology is controlled through a newly developed modulation technique and possible working modes are analyzed and described thoroughly. For performance validation, the experimental analysis of grid connected proposed inverter is performed on a 1 kVA system and results show that proposed inverter feeds power in to the grid with lesser THD while achieving greater efficiency. [ABSTRACT FROM AUTHOR]

The use of power converters as solid state transformers is an attractive solution to modernize the power network, but this solution has not been fully addressed for MV and HV substations. This paper presents a customized and simple control for the Modular Multilevel Matrix Converter (M3C), specially conceived for its operation on synchronous ports, which is the case of AC substations. The control allows bidirectional power transfer, generation/absorption of reactive power and provisions of ancillary services. The converter is compared to the back-to-back Modular Multilevel Converter (B2B-MMC) where the key performance indicators to carry out the comparison are power efficiency, number of semiconductor devices, passive components required, footprint, voltage cell balance, fault blocking capability and stress of components. The simulation results show the features, performance and attractiveness of the M3C topology in a 33/11 kV, 16 MW substation under different operating conditions, including grid faults and dynamic operation. The M3C presents similar efficiency and performance than the B2B-MMC, but it uses fewer semiconductor devices, passive components and total cell capacitor energy than the B2B-MMC, reducing cost and footprint. The experimental results show the performance of the M3C under less ideal conditions including a substation transformer saturation and power step response. [ABSTRACT FROM AUTHOR]

Multilevel converters (MLCs) are pioneers in the field of electrical energy conversion. From the classification of MLCs, modular multilevel converter (MMC) is top-rated due to its attractive structure and performance. The modular nature and no need for isolated DC resources are two significant advantages of this converter. However, the need for many sensors to control its performance is a considerable drawback. In addition, the internal circulating current in the MMC causes losses, decreases efficiency, and increases the voltage ripple of capacitors. This paper proposes combining a new capacitor voltage sorting method and an open-loop controller based on arms energy estimation to control the MMC using two voltage sensors in the arms and one current sensor at the output. The proposed method ensures continuous voltage balancing of the capacitors and removes multiple voltage sensors from sub-modules (SMs). The simulation and experimental results verify the accuracy and effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

The paper addresses an optimization-based reference calculation method for Modular Multilevel Converters (MMC) operating in normal and constrained situations (when the converter needs to prioritize its quantities as it has reached voltage or current limitations, e.g. during system faults). The optimization problem prioritizes to satisfy the external AC active and reactive current set-points demanded by the grid operator through the corresponding grid code. If the operator demands are fulfilled, it uses the available MMC degrees of freedom to minimize the arm inductance losses. Otherwise, if the operator demanded AC set-points cannot be accomplished, the optimization attempts to minimize the error prioritizing between either AC active or reactive currents. The optimization problem constraints are imposed through a steady-state model considering simultaneously the external and internal AC and DC magnitudes of the converter. The steady-state model also includes the voltage variation in the equivalent arm capacitors (considering the ripple). Then, the imposed limitations are the maximum allowed grid and arm currents, the maximum allowed arm voltages and the sub-module capacitor maximum voltages. The paper presents a detailed formulation of the optimization problem and applies it to several case studies where it is shown that the presented approach can be potentially used to obtain the MMC references both in normal and fault conditions. [ABSTRACT FROM AUTHOR]

This paper presents a new soft switching high voltage gain interleaved dc-dc converter with a three-windings coupled inductor for a fuel cell vehicle. Two interleaved and intercoupled boost cells are connected by the input parallel and output series (IPOS) configuration, realizing low input current ripple and high voltage gain simultaneously. All power switches can operate under soft switching conditions by only adding a simple auxiliary circuit composed of one auxiliary inductor and one power switch. Besides, the auxiliary inductor is coupled with the main inductors, which results in a rapid zero convergence of the auxiliary current and a small conduction loss of the auxiliary circuit. The operating principle, steady state characteristic, comparison with other converters, and parameter design are analyzed in this paper. Finally, the main characteristics of the proposed converter are verified by a 1-kW laboratory prototype. [ABSTRACT FROM AUTHOR]

This paper summarizes the work performed by the Task Force —within Performance Characteristic Subcommittee of IEEE PES Transformers Committee— to investigate potential revisions to IEEE Std C57.142-2010. Although the scope of this document does not implicitly exclude HV and EHV systems, the existing document primarily includes examples and information on distribution voltage systems. A Task Force was formed to investigate the need to include information about power system transient events on HV systems more explicitly in this existing document. The Task Force was charged with the following tasks:-Establish system voltages encompassed by C57-142-2010 Guide. -Gather field data, reports, and literature on HV and EHV failures related to substation transients and transformer interaction. -Solicit input from the other technical committees on this subject. -Review IEC and CIGRE work in this area. -Recommend course of action on revision of the present Guide. -Recommend high level changes to the Guide. -Prepare final paper for the Subcommittee. In the course of this work several failure scenarios were identified. These are categorized and the failures are described in this paper. The final recommendations to the Subcommittee are summarized and recommendations are presented for the course of action on the revision/addition of HV and EHV material to the current C57.142 Guide. [ABSTRACT FROM AUTHOR]

When a fault occurs on the dc side of the voltage source converter based high voltage direct current (VSC-HVDC) transmission system, the fault current rises quickly due to the low damping of the dc system. Using a dc fault current limiter (DC-FCL) to limit the rise of the fault current can significantly reduce the breaking requirements of the DCCB. A topology of a bidirectional active dc fault current limiter (BA-FCL) based on coupled inductor is proposed in this paper. No expensive full-controlled power electronic devices are used in this topology. Only a few half-controlled power electronic devices are used to achieve active control of the current limiting unit. Compared with many topologies of current limiter at present, the fault current limiting effect of BA-FCL is improved significantly while the cost, volume, topology complexity, and control complexity are reduced. The stress analysis and parameter design of the proposed current limiter are carried out. Finally, the simulation case study and hardware experiment are implemented to verify the good economy and current limiting performance of the proposed topology. [ABSTRACT FROM AUTHOR]

As the weakest components of wind turbine converters, dc-link capacitor withstands high-frequency ripple currents from both rectifier and inverter. Traditional wind turbine control strategy does not consider the influence of the harmonic current generated by both side converters on the dc-link capacitor, and ignores the restriction on the reliability of direct-drive wind turbine converter. For the reason, this paper synthesized the wind turbine model and dc-link capacitor harmonic spectrum analytical approach to derive the connection between mission profile and harmonic spectrum. Regarding with the capacitor lifetime model, the optimal mapping from control strategy to mission profile, maximizing the service life of capacitor, was solved. With the proposed health-oriented control strategy, the core temperature of dc-link capacitor can be effectively reduced, which can increase the service life of capacitor, making the dc-link capacitor no longer the most fragile component in wind turbine converter and ultimately improving the reliability of converters. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

As high-speed railways develop rapidly worldwide, the problems of neutral section and power quality are becoming increasingly prominent. These problems affect the normal operation of the power grid and the electric locomotives. The co-phase power supply schemes were proposed by researchers, which can solve these problems well. Among them, the MMC-based scheme (MMC-5 L) is a representative one. The existing scheme, when applied to the auto-transformer (AT)-fed system which is usually adopted by high-speed railways, needs to install an auto-transformer on the output side. To eliminate the auto-transformer and to obtain the more suitable and superior co-phase power supply schemes to AT-fed system, two improved schemes are proposed in this paper based on the novel MMC-based scheme (MMC-6 L) we proposed before. While establishing the mathematical model, creating the control system, and carrying out simulation verification of the proposed schemes, the proposed schemes are compared with MMC-6 L and MMC-5 L in terms of topological characteristics, control system complexity, power loss, and functionality. The results show that while the proposed schemes can fulfill the functions of the co-phase power supply scheme well like the MMC-5 L and MMC-6 L, they are more suitable and superior for the AT-fed system in terms of control system complexity and power loss. Among them, MMC-5L1CB performs best in power loss, and MMC-4L2CB performs best in control system complexity. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) in high- voltage applications contain large numbers of power switches, which increases the fault probability inside MMCs. This paper proposes a detection method for the faulty arm containing switch open-circuit failures in high-voltage MMCs to improve the reliable operations of MMCs. The proposed method uses the periodicity of the deviation between the maximum and minimum capacitor voltages to provide the detection reference. To yield a reliable reference, the repetitive signal generator is employed. Then, the fault is identified by the difference between the referenced and measured capacitor voltage deviations. An auxiliary criterion is also designated to avoid the false detection caused by the mutations in MMCs. The proposed method can reduce the difficulty in the selection of thresholds. Moreover, the proposed method is robust in high-voltage MMCs with inferior capacitor voltage balancing performance, which ensures detection rapidity and accuracy. Finally, the feasibility of the method is verified by simulation results in Matlab/Simulink. [ABSTRACT FROM AUTHOR]

Transmission adequacy of power system has been challenged by high investment of new line construction and limit line-corridor space. In this paper, a novel solution to increase transmission capacity by altering HVAC lines into fractional frequency transmission system (FFTS) is proposed. FFTS is a transmission that utilizes a relatively low grid frequency, e.g., 50/3 Hz, to extend the transmission capacity of ac lines. The proposed solution can minimize the construction efforts since the existing HVAC transmission lines can be directly employed by FFTS without any change. The structure and principle of FFTS for transmission line conversion (TLC) are introduced firstly. Then, performance of conventional ac equipment in FFTS is evaluated and comparison with respective counterpart in HVDC is carried out. Next, the economic performance of FFTS for transmission capacity upgrade is conducted based on a typical benchmark, and sensitivity analysis results are presented to determine the economic zone of FFTS. The results show that the uniform annual value (UAV) of TLC into FFTS is 24.9% and 31.6% cheaper than TLC into HVDC and constructing new HVAC lines, respectively. Therefore, FFTS is a superior scheme for transmission capacity boost. [ABSTRACT FROM AUTHOR]

Ultra-high voltage fast vacuum circuit breakers (FVCBs) could benefit a power system by promoting transient stability because their opening and closing times are significantly lower than those of commonly used circuit breakers at transmission voltage. This paper presents the design and verification of a prototype 363-kV/5000-A – 63-kA multiple-break FVCB. The prototype consists of two parallel-connected circuit branches in each phase. Each branch comprises three breaking units. The breaking unit, arranged on a 330-kV-class insulating platform, is a double-break FVCB driven by two independent electromagnetic repulsion actuators. The breaking units include a specially designed 40.5-kV vacuum interrupter (VI) with an extended ceramic envelope and optimized contact contours. A 4.0-nF grading capacitor is connected in parallel with each break to achieve a uniform stressed voltage distribution across the break. The prototype performs controlled switching of short-circuit current with an arcing time of 2.0 ms. The feasibility of the 363-kV FVCB is verified by a dielectric test on one break of the prototype and a series of tests on a single-phase prototype according to the international standard IEC 62271-100, 2017 and the Chinese standard GB 1984-2014. The tests include controlled switching of a short-circuit current in a short arcing time under different transient recovery voltages following test duties T100s(b) and T100a, short-time withstand current and peak withstand current tests, a temperature rise test, and an electromagnetic compatibility test. [ABSTRACT FROM AUTHOR]

The separation of the data capture and analysis in modern vision systems has led to a massive amount of data transfer between the end devices and cloud computers, resulting in long latency, slow response, and high power consumption. Efficient hardware architectures are under focused development to enable Artificial Intelligence (AI) at the resource-limited sensing devices. One of the most promising solutions is to enable Processing-in-Pixel (PIP) scheme. However, the conventional schemes suffer from the low fill-factor issue. This paper proposes a PIP based Complementary Metal-Oxide-Semiconductor (CMOS) sensor architecture, which allows convolution operation before the column readout circuit to significantly reduce the overall power consumption while improving the resource utilization of the succeeding deep learning accelerator. The simulation results show that the proposed architecture could support the computing efficiency up to 3.37 TOPS/W at the 8-bit weight configuration, which is four times as high as the conventional schemes after normalization. The transistors required for each pixel are only 3.5T, significantly improving the fill-factor. [ABSTRACT FROM AUTHOR]

This paper applies the principles of distribution locational marginal pricing (DLMP) to unbalanced three-phase distribution networks. We first propose a linear model for AC optimal power flow derived through a series of approximation and reformulation techniques. Then a scenario-generation algorithm is proposed to properly model the uncertain parameters in the linear model. Through a proposed No U-Turn sampler (NUTS) based algorithm, probability density functions (PDFs) of DLMPs are calculated. These PDFs provide statistical information about the locational and temporal price risks. By means of applications to two IEEE unbalanced test networks, the numerical results show promising performance for the proposed linear model and the NUTS-based algorithm in creating PDFs of DLMPs. DLMP price densities will be increasingly useful as distribution system operators seek flexible, low risk solutions from embedded generators and aggregators of distributed energy resources. [ABSTRACT FROM AUTHOR]

Differential power processing (DPP) converters have been developed for photovoltaic (PV) panels to preclude energy yield reduction due to partial shading. In large-scale PV systems comprising numerous series-connected panels, DPP converters with good modularity are preferable because the number of series-connected panels varies depending on applications. This paper proposes a switched capacitor converter (SCC)-based modular DPP architecture for large-scale PV systems. Four panels are grouped as a module, each having a panel-level DPP converter, and modules are connected in series to form a string. The design of the panel-level DPP converter is fixed while the system can be arbitrarily extended by stacking modules, achieving good modularity. Adjacent panel-level DPP converters are dc-coupled, by which modules can be connected using long cables, mitigating installation limitations. The experimental results of the laboratory and field testing demonstrated the energy yield enhancement by 10%–20%, depending on shading conditions. [ABSTRACT FROM AUTHOR]

Virtual synchronous generator (VSG)-based control approaches for AC machine drivers have attracted much attention in recent years. The contradiction between the strong motor loading capacity and the small DC voltage fluctuation is disregarded in previous studies. A larger virtual inertia is required to raise the torque gain and drive the motor with heavier loads, thus resulting in greater DC voltage variations. A systematic method is proposed for the optimal design of the virtual inertia for VSG-based motor starting systems to achieve the maximal motor loading capacity and the low DC voltage fluctuation in this paper. Firstly, the relationship between the virtual inertia and the loading capacity is revealed on the basis of the closed-loop analysis. Considering the DC voltage variation, the constraint on the maximal value of the virtual inertia is proposed from the energy-balance perspective despite the unknown contribution of the DC capacitors to the virtual inertia. To fully exploit the energy storage capacity of the DC capacitors and raise the upper limit of the virtual inertia under the same permitted DC voltage variation, a modified DC voltage reference is introduced. Extensive simulation and experimental results are presented to validate the effectiveness of the proposed methods. [ABSTRACT FROM AUTHOR]

The paper develops two computationally efficient models, namely a detailed equivalent model and an average-value model, with provisions for representation of the critical state of converter blocking, for modular multilevel converters with embedded storage. These models are indispensable in the simulation of dc faults. The developed detailed equivalent model provides accuracy that matches electromagnetic transient (EMT) simulations, with much reduced computational burden; the developed average-value model represents the averaged behavior of the converter by neglecting switching transients. Both models are extensively evaluated in the context of an HVDC system against benchmark results form a detailed switching model developed in PSCAD/EMTDC. The results confirm the validity and accuracy of the models for steady state, transient, and faulted operating conditions including when the converter is blocked in response to a dc fault. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

The vacuum interrupter-based DC circuit breaker is one of the most important equipments in the DC power system. The dielectric recovery (DR) of vacuum interrupter (VI) is essential for breaking reliability, especially on some occasions with ultra-large fault current such as the outlet of generator. To measure the DR of VI under high arcing current, an experiment circuit is designed and the DR under arcing current from 20 kA to 60 kA is presented in this paper. The influence of arcing current, contact separation, di/dt before current zero and arcing time on the DR is investigated. Particularly, it's found that under a specific arcing current, there exists an optimal arcing time for DR, and it shows a negative correlation with the arcing current. [ABSTRACT FROM AUTHOR]

Different from typical circuit breakers, breakers used to switch AC filters in convertor stations have to operate frequently according to the real-time operation mode and daily load changes. Therefore, the performance of filter breakers decreases very quickly, which leads to frequent accidents. Both preinsertion resistors and controlled switching devices can suppress switching transients. In this paper, a comparative analysis of whether a controlled switching device and preinsertion resistor should be adopted is carried out using PSCAD. The transient is calculated as the combined result of the switching angle and preinsertion resistor value, and the optimal configurations are proposed. After determining the resistor value and whether a controlled switching device should be included, the reference voltage of the arrester should be reevaluated. [ABSTRACT FROM AUTHOR]

The single-phase-to-ground (SPG) fault at the valve side of the converter transformer is one of the most critical faults threatening the operation of bipolar half-bridge modular-multilevel-converter-based multi-terminal direct-current (HB-MMC MTDC) systems. Following a valve-side SPG fault, the upper-arm submodule (SM) capacitors in the faulty converter may suffer a serious overvoltage, and the grid-side fault currents may experience no zero-crossings. The existing protection methods generally rely on tripping the grid-side alternate-current circuit-breaker (ACCB), which cannot fully isolate the fault. The healthy poles and stations may encounter severe disturbance and be all blocked, which will lead to a power outage of the entire MTDC system. This paper proposes an ACCB-independent scheme based on thyristor-pairs and damping SMs to address these problems. Antiparallel thyristor-pairs are connected in series within the upper and lower arms in each phase. Serial damping SMs are connected within the lower arms to help the lower-arm thyristor pairs cut off the fault currents. Although the proposed additional devices inevitably cause conduction losses, they can effectively protect the faulty converter and healthy circuit in the MTDC system. Simulations in PSCAD/EMTDC have been conducted to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

Voltage source converters (VSCs) have been extensively used in power systems for interfacing renewable energies and other modern loads. Because of their nonlinear nature, a proper harmonic model of VSC devices must be established when conducting harmonic analyses in power systems. This is especially true for low-order harmonics, which are routinely encountered in present power systems. To this end, an analytical harmonic model that represents the low-order harmonic characteristics of VSCs is developed in this paper. The new model takes both the control loop and power loop (i.e., DC-link capacitor) of the VSC into account through rigorous mathematical derivations. The final result has shown that the VSC can be represented by a harmonically coupled impedance matrix at harmonic frequencies, which can be easily used for harmonic analyses of large-scale power systems. It also shows that the DC-link capacitor has a more noticeable impact on the harmonic impedance of VSCs with a smaller DC-link capacitance and low-order harmonics. The appropriateness of the new model was verified using EMT simulations and lab experiments. A complete procedure to construct the proposed VSC model is also established based on the research findings. [ABSTRACT FROM AUTHOR]

The second-harmonic injection strategy for modular multilevel converters (MMCs) can effectively suppress the capacitor voltage fluctuation in steady states. However, the capacitor voltage fluctuation under grid-side single-line-to-ground (SLG) faults will be more severe. Moreover, there is no research on the mitigation of capacitor voltage fluctuation under grid-side SLG faults for the hybrid MMC with mixed half-bridge and full-bridge sub-modules. To address this issue for hybrid MMCs, an optimal second-harmonic current injection scheme for mitigating the capacitor voltage fluctuation in the hybrid MMC under grid-side SLG faults is proposed in this paper. The mathematical models of arm power fluctuations of the hybrid MMC are firstly developed under both steady states and grid-side SLG faults. Then, the principle and optimal strategy of the proposed capacitor voltage fluctuation strategy are presented. The capacitor voltage fluctuation under grid-side SLG faults can be reduced by suppressing the three-phase arm power fluctuations. A hybrid MMC model with the proposed scheme has been established in PSCAD/EMTDC to verify its effectiveness and feasibility. Simulation results show that the average voltage fluctuation reduction rate can reach 55.77% with the proposed strategy. [ABSTRACT FROM AUTHOR]

The current-limiting inductors (CLIs) are commonly used to suppress DC fault current to safely trip DC circuit breakers in MMC-HVDC systems, but it significantly jeopardizes DC dynamics and causes instantaneous power mismatch between AC and DC sides of islanded rectifier station (RS), exposing MMC internal states to large disturbance. This paper firstly provides a detailed analysis of the influence of CLIs on AC fault, establishes RS mathematical representation including AC side dynamic, and reveals the mechanism of DC voltage oscillation, modulation saturation and PCC waveform distortion. The analysis shows that the AC and DC fault characteristics are decoupled under unsaturated AC modulation, but coupled under excessively low submodule capacitor voltage, where AC modulation is saturated and PCC waveforms are distorted. To solve this issue, a novel RS AC fault ride through method for MMC-HVDC system with CLIs is proposed to stabilize RS DC voltage, desaturate AC modulation and decouple fault characteristics by regulating the zero-sequence modulation of circulating current suppression. In addition, a current reference disturbance and an AC energy dissipation device coordinated control are designed, which adaptively recovers the submodule capacitor voltage. Finally, the feasibility of the proposed method is verified by simulation results. [ABSTRACT FROM AUTHOR]

This paper proposes a traveling wave based scheme for wye-connected shunt capacitor bank protection. The proposed method provides high sensitivity and fast response, assisting in mitigating capacitor damage during internal cascading failure. The available protection schemes for capacitor bank use RMS values of voltage and current phasors for trip decision. Threshold selection is required in these methods which needs accurate estimation of equivalent capacitance of the bank. In addition, phasor being estimated from one-cycle running data window, such a method is slow. The proposed traveling wave based method identifies an internal fault in case of opposite polarities of traveling waves seen in the terminal voltage and current signals of the faulted phase. If the mid-point tapping is available in capacitor bank, the faulted half can be identified using the traveling wave of tap voltage. The magnitude of the traveling wave in terminal voltage reveals the number of failed capacitor elements. Such information assists in expediting maintenance. The performance of the proposed method is tested using PSCAD/EMTDC simulation data for various situations, including internal short circuit, external, and identical faults in the shunt capacitor bank. Comparative analysis highlights its higher sensitivity and better accuracy in comparison to available protection methods. [ABSTRACT FROM AUTHOR]

The HVDC systems have been employing modular multilevel converters (MMC) due to their unique high voltage high power potential. However, the lack of fault ride-through capability imposes restrictions on MMCs that are based on half-bridge (HB) modules. Since it is necessary to limit the fault currents to protect MMCs from serious short circuit faults against pole-to-pole DC fault, several protection schemes have been introduced to deal with the DC short circuit faults. This paper proposes a new hybrid MMC protective topology consisting of a combination of the HB and three-quarter-bridge (TQB) modules. The TQB behaves like an HB under normal operation and has low power losses compared to other protective topologies. Modulation and control of this configuration are like HB-based MMC. In the proposed hybrid protective topology, during a pole to pole DC fault, the fault current can be either blocked or be limited by TQB-SMs. Both simulations and experiments were performed to verify the operation of the suggested hybrid MMC in different modes of operation. [ABSTRACT FROM AUTHOR]

Miniaturization and low cost contribute to the development and popularization of wireless power transfer (WPT). Reducing the number of power conversion stages can reduce the volume and cost of the WPT converter, and even make it possible to improve the efficiency. A single-stage WPT converter with constant current (CC) and constant voltage (CV) output and its asymmetric modulation method are proposed in this paper. A direct AC-AC converter is applied to the primary side of the WPT converter to directly convert line-frequency AC to high-frequency AC. The applied direct AC-AC converter that can replace the commonly used multi-stage primary converter reduces the number of circuit devices, thereby reducing the volume and cost of primary converter. The proposed WPT converter can realize zero voltage switching (ZVS) and power factor correction (PFC). In order to achieve CC and CV output, a switchable hybrid compensation topology is applied to the proposed WPT converter. A 720-W experimental prototype was manufactured to verify the rationality of the proposed WPT converter and the correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes an adaptive model of modular multilevel converter (MMC) for electromagnetic transient (EMT) simulations. The model is applicable to MMCs with arbitrary numbers of half-bridge and full-bridge submodules. The proposed design includes average value model, arm equivalent model, and detailed equivalent model. It allows smoothly transitioning from one model to another during time-domain simulations depending on the desired accuracy and execution time constraints. Modifications required in conventional MMC models to achieve smooth transitions are presented in the paper. Time-domain initialization methods are developed for each constituting model, including initialization of the appropriate control system blocks. Validity and effectiveness of the proposed adaptive model is demonstrated using EMT simulations of 401-level MMC-HVDC system. [ABSTRACT FROM AUTHOR]

This paper presents an evolution of control systems of Modular Multilevel Converters (MMCs) focusing on the internal voltages and currents dynamics. MMCs have passive components inside the converter that create extra dynamics compared to conventional VSCs. Some control schemes that do not consider these internal dynamics may still stabilize the system asymptotically thanks to the linearisation in the modulation step. However these control schemes are less robust because they are prone to poor damped oscillations on the dc side of the converter. The MMC circuit and energy relationships are presented in this paper. Along with a gradual development of the energy based control, the important roles of each internal dynamics are clearly demonstrated. Experimental results are presented to show the impacts of the linearisation in the modulation step on the system behaviour. [ABSTRACT FROM AUTHOR]

This paper presents a new control strategy for enhancing the dc voltage regulation and the transient response in the multi-terminal VSC-HVDC system by ensuring swift power-sharing among converters when encountering large disturbance such as converter loss or ac fault at one of the converter stations. The quick power sharing can be realized using direct power control (DPC) since it has a merit of fast power dynamic response. On the other hand, to limit the converter current during ac fault, a new coordination strategy between DPC and vector current control (VCC) is proposed. Furthermore, a new simplified model of the MTDC system is developed to study the performance of DPC in enhancing the dc voltage dynamics response analytically. The time-domain simulation of the detailed model of the four converter stations MTDC system verify that the proposed control strategy significantly reduces the overshoot in the transient dc voltage response following an outage or ac fault. As a result, together with the droop gain selection for the maximum permissible steady-state dc voltage deviation, the proposed control strategy can help to reduce the size of the dc chopper in the MTDC grid or even avoiding it. Moreover, the comparative analysis based on time-domain simulation depicts that the proposed simplified model has the same dc voltage response compared to the detailed model of the MTDC system except for a steady-state error of 0.47% and a little bit longer settling time (1.5 ms) at transient. [ABSTRACT FROM AUTHOR]

The high di/dt before zero-crossings easily leads to delayed or failed operations for the active current injection mechanical DC circuit breaker, especially for small direct current interruptions. The pre-charging process also makes this type of circuit breaker hard to realize repeat operations economically in the high voltage DC system. This paper proposes a novel DC circuit breaker and its design method that deeply coordinating a superconducting fault current limiter with the active current injection DC circuit breaker. This method significantly reduces di/dt before current zero-crossings and enables repeat operations economically. Besides limiting fault currents, the superconducting fault current limiter also charges the resonance capacitor flexibly in the circuit breaker, realizing the injected reverse current keep a constant proportion to the arbitrary fault current. Validations of the flexible capacitor charge and repeat operations are made by simulation and low voltage experiments. The charging times are within 2.5 ms and the reverse current keeps 1.2 to 1.7 times over the fault current under arbitrary conditions. Di/dt at current zero is reduced by 80% under 30% of rated interruption capacity. Flexible capacitor charge experiments are consistent with the simulation design. The superconducting tapes can recover within 300 ms to support repeat operations. [ABSTRACT FROM AUTHOR]

In 2014 a number of Capacitor Voltage Transformers (CVTs) exploded in the Swedish transmission grid. To address this problem, data driven methods for continuously monitoring CVTs were developed. Thanks to these methods, CVT capacitor punctures are now regularly noticed and addressed before causing serious damage. This paper describes the algorithms used to make this possible. Detecting all CVT capacitor punctures as they occur increases the transmission system stability, avoids equipment damage, lowers risks to personnel when visiting the substations and makes it possible to correct measurement errors in the energy measurement systems. Automatic supervision scripts, using energy meter data, are running continuously and will alert the service personal immediately when problems occur. With the algorithms proposed in this article, the Swedish National Grid (Svk) has detected many old punctures and expects no future capacitor punctures to go undetected. Detecting all new punctures enables Svk to save substantial future cost since planned actions now are possible. [ABSTRACT FROM AUTHOR]

In this paper, a hybrid time-domain protection scheme for series compensated lines using incremental quantity combined with traveling wave principle is proposed. Each principle is assigned a zone of the protected section of the line to achieve fast protection. The incremental quantity-based method is assigned for close-in faults up to 35% and the traveling wave from 33.33% to 66.67% of the line from the relay end. The incremental quantity-based method compares a dynamic restraining quantity obtained from voltage and current to the operating quantity using current for the protection decision. The traveling wave-based method derives a decision by comparing the calculated line length, obtained using the first three arrival times measured at the relay location, to the actual line length. The proposed hybrid approach exploits the advantages of both principles to achieve better reliability and speed of protection for series compensated transmission lines. The proposed scheme is verified for a 400-kV, 300 km series compensated transmission line and results are compared with traditional impedance and incremental quantity-based methods. [ABSTRACT FROM AUTHOR]