Search

In this paper, a new family of impedance source inverters is presented. It employs high-frequency electrical isolation between the inverter bridge switches and the load along with voltage clamping across the dc-link voltage. Conventional Z-source inverters (ZSIs) employs an impedance network that consists of inductors and capacitors. It has unique features that realize both step-up/step-down functions and eliminates the need of dead/overlap times. This paper extends this novel concept by using electrical isolation in impedance source inverters. High-frequency isolation has many advantages in terms of immunity and reliability; when applied with impedance source inverters this makes ZSIs a preferable choice for industrial applications. In photo-voltaic systems, the addition of the high-frequency transformer provides safety by avoiding the injection of dc circulating current into the grid, without the need of an external bulky line frequency transformer. The gain of the proposed inverter design can be accurately selected by choosing the turns ratio of the high frequency transformer (HFT) or by adjusting the shoot-through duty cycle (STDC) to the inverter. This allows for greater freedom especially when utilizing a higher modulation index, with the STDC allowing dynamic gain adjusts to be done speedily during operation of the inverter. Additionally, a dc-rail voltage clamping technique for the proposed class of isolated ZSIs is also discussed. This technique provides benefits not only in improving the output voltage quality, but also in reducing voltage stress of the active and passive components by minimizing the voltage spikes across the switching devices. In this paper, several high-frequency isolated ZSIs are presented, and an example isolated improved ΓZSI design is shown and discussed in detail. Simulations are provided for the proposed class of isolated inverters to verify their working. Further experimental investigation has been done for which results for the isolated improved ΓZSI are reported. These empirical results have largely confirmed the expected benefits that were determined through simulation and accurate model-based testing. [ABSTRACT FROM AUTHOR]

This paper proposes a split-capacitor four-wire current source inverter, which is the dual of the split-capacitor four-wire voltage source inverter. Since the midpoint of the dc link is tied to the neutral point of ac filter capacitors, the common-mode voltage (CMV) is reduced significantly. Consequently, the leakage current issue is effectively addressed. The proposed circuit is cost-effective as no extra switch is added. This paper, first, establishes the equivalent common-mode circuit of the proposed inverter. The impact of the neutral line inductance on CMV is also analyzed. Then, a specific modulation is introduced to balance the dc-link voltages/currents. To achieve good input/output performance, a nonlinear control method is developed based on time-domain models. Finally, all the proposed methods and related theoretical analysis are verified by simulations and experimental results. [ABSTRACT FROM AUTHOR]

Generating dense multilevel voltage space structure using polygons of higher sides is one of the novel and elegant method to suppress low-order harmonics and to obtain refined sinusoidal voltages using voltage source inverters for variable frequency drive application without passive filters. Apart from the advantages of conventional multilevel inverter topologies, schemes generating polygonal voltage space vector structure can equip full dc-bus utilization, low switching frequency strategies to eliminate low-order harmonics, and increased linear modulation range. In this paper, an induction motor drive scheme generating a highly dense multilevel 24-sided polygonal voltage space vector structure using a single dc source, which can eliminate harmonics till 23rd order from phase voltages, is presented. Cascaded power circuit topology with a flying capacitor inverter fed with a dc source and two low voltage floating capacitor fed H-bridge inverters is used. Detailed experimentally validated results, under scalar as well as indirect rotor field oriented control of induction motor are provided. Studies on voltage ripple and reactive energy in various floating capacitors, harmonic performance of output voltage for wide range of speed operation, are also included. [ABSTRACT FROM AUTHOR]

Modular multilevel converters are increasingly being considered or used for various medium voltage applications. Multiple control methods have been proposed for the control of the direct to three-phase modular multilevel converter. They differ one from another in the way the capacitor voltage ripples are handled, i.e., either neglected, estimated, reconstructed by filtering or measured. This has implications on the performance level that can be obtained. This paper provides insights on the advantages and drawbacks of each control method, in inverter and rectifier mode, with a fair and thorough assessment supported by extensive simulations, with converter ratings that are realistic for medium voltage applications. Finally, this works highlights the impact of the higher dynamics for medium voltage direct current (dc) applications compared to high voltage dc ones on the choice of the control method. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

Owing to low cost, small size, and low weight, transformerless inverters became prominent in single-phase grid connected photovoltaic (PV) systems. Key issues pertaining to these inverters include suppression of common mode (CM) leakage current and improvement of conversion efficiency. Achieving higher efficiency in single-phase grid-connected photovoltaic systems depends on the number of stages involved in feeding power to the grid, predominantly, if the PV array voltage is less than the peak value of the grid voltage. In this paper, an integrated dc–dc converter based grid-connected transformerless PV inverter is proposed which is aimed at maintaining high efficiency, even if the PV array voltage falls below the peak value of grid voltage (efficient operation at an extended input voltage range). A modulation strategy is discussed in order to minimize the flow of CM leakage current. Further, the efficiencies of certain transformerless inverter topologies are analyzed and compared with that of the proposed topology. Detailed simulation studies are carried out in MATLAB/Simulink environment to verify the analysis. Experimental results for a scaled down laboratory prototype are included as a proof-of-concept to validate the claims. [ABSTRACT FROM AUTHOR]

This paper proposes a vector control strategy for independent control of two permanent-magnet synchronous motors (PMSMs) using a single four-leg inverter (4LI). An expanded two-arm modulation to obtain a balanced three-phase output voltage is described. This paper also proposes a method to compensate for the fluctuations in the neutral point voltage of two split capacitors in the dc link. The experimental results show that independent speed and position control of two PMSMs can be achieved using a single 4LI with the proposed vector control method. [ABSTRACT FROM AUTHOR]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper presents a single-phase ac power supply circuit that based on modified voltage-fed quasi-Z-source inverter topology; it suits to the light or the heavy load and is fit for the resistive, inductive, or capacitive load. The topology, operating principle, voltage gain, control method, and its realization by DSP are described in this paper. The feasibility and rationality of the system is verified by the simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Indirect matrix converter (IMC) is an alternative for ac/ac energy conversion, usually operated with a voltage stepped-down gain of only 0.866. For applications like distribution generation where voltage-boost functionality is required, the traditional style of operating the IMC is therefore not appropriate. Like most power converters, the operation of the IMC can surely be reversed to produce a boosted gain, but so far its relevant control principles have not been discussed. These challenges are now addressed in this paper with distributed generation suggested as a potential application. Simulation and experimental results for validating various performance aspects of the proposed control schemes can be found in a later section of this paper. [ABSTRACT FROM AUTHOR]

Multilevel inverters are receiving more attentions nowadays as one of preferred solutions for medium- and high-power applications. As one of the most popular hybrid multilevel inverter topologies, the five-level active-neutral-point-clamped inverter (5L-ANPC) combines the features of the conventional flying-capacitor type and neutral-point-clamped (NPC) type inverter and was commercially used for industrial applications. In order to further decrease the number of active switches, this paper proposes a seven-switch 5L-ANPC (7S-5L-ANPC) topology, which employs only seven active switches and two discrete diodes. The analysis has shown a lower current rating can be selected for the seventh switch under high power factor condition, which is verified by simulation results. The modulation strategy for 7S-5L-ANPC inverter is discussed. A 1 kVA single-phase experimental prototype is built to verify the validity and flexibility of the proposed topology and modulation method. [ABSTRACT FROM AUTHOR]

This paper describes novel single-phase solutions with increased inverter voltage levels derived by means of a nonstandard inverter configuration and impedance source networks. Operation principles based on special modulation techniques are presented. Detailed component design guidelines along with simulation and experimental verification are also provided. Possible application fields are discussed, as well as advantages and disadvantages. Finally, future studies are addressed for the new solutions. [ABSTRACT FROM PUBLISHER]

Eliminating the leakage current is one of the most important issues for transformerless three-phase photovoltaic (PV) systems. In this paper, the leakage current elimination of a three-phase four-leg PV inverter is investigated. With the common-mode loop model established, the generation mechanism of the leakage current is clearly identified. Different typical carrier-based modulation methods and their corresponding common-mode voltages are discussed. A new modulation strategy with Boolean logic function is proposed to achieve the constant common-mode voltage for the leakage current reduction. Finally, the different modulation methods are implemented and tested on the TMS320F28335 DSP +XC3S400 FPGA digital control platform. The experimental results verify the effectiveness of the proposed solution. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology named the active-switched-capacitor/switched-inductor quasi-Z -source inverter (ASC/SL-qZSI), which is based on a traditional qZSI topology. Compared to other qZSI-based topologies under the same operating conditions, the proposed ASC/SL-qZSI provides higher boost ability, requires fewer passive components such as inductors and capacitors, and achieves lower voltage stress across the switching devices of the main inverter. Another advantage of the topology is its expandability. If a higher boosting rate is required, additional cells can easily be cascaded at the impedance network by adding one inductor and three diodes. Both the simulation studies and the experimental results obtained from a prototype built in the laboratory validate proper operation and performance of the proposed ASC/SL-qZSI. [ABSTRACT FROM AUTHOR]

The differential-mode Ćuk inverter (DMCI) is a single-stage inverter with low device count. It offers advantages over other topologies because of compactness, higher power density, and reduced cost. It is a promising topological configuration for renewable-/alternative-energy applications with isolated as well as nonisolated structures. The continuous modulation scheme (CMS), which was introduced originally for this inverter, activates all the modules of the DMCI. The new discontinuous modulation scheme (DMS) deactivates one module in each half line-cycle leading to discontinuous operation of modules. This paper outlines the DMS and a mechanism to realize it. The experimental open-loop and closed-loop results of the DMCI using CMS and DMS are provided along with a comparison of their performances. It is shown that, the DMS reduces the circulating power and hence mitigates the losses. The voltage ratings of the devices also are reduced with the DMS. In contrast, the CMS has wider linearity in its normalized dc-voltage gain and yields reduced harmonic distortion of the output voltage. For DMS, to achieve comparable linearity in normalized dc-voltage gain and distortion, harmonic compensation under closed-loop control is a pathway that has been demonstrated. [ABSTRACT FROM AUTHOR]

This paper introduces a new dc-ac converter with the feature that it produces an instantaneous output voltage higher or lower than the input dc voltage without an intermediate power stage or transformers. This feature is provided by using one switching cell including two switches, two diodes, one inductor, and one capacitor on each inverter leg. Validating the theoretical analysis, a prototype was designed, built, and tested for an output rated power of 1 kW, a dc input voltage of 96Vdc, and output voltage of 110 Vrms. Furthermore, the fundamental output frequency was established at 60 Hz and the switching frequency at 20 kHz. [ABSTRACT FROM AUTHOR]

This paper presents a novel direct current-fed interleaved phase-modulated single-phase unfolding inverter for fuel-cell applications. Two active-clamped zero-voltage switching current-fed half-bridge isolated converters are interleaved in parallel input and series output configuration. Phase modulation is proposed to control these two converter cells, which generate a rectified sinusoidal pattern at the dc link. A simple H-bridge unfolding dc–ac inversion is used to produce single-phase sine voltage at line frequency switching using square-wave control. This not only simplifies the inversion stage in terms of modulation but also reduces the switching losses. Direct front-end current-fed based unfolding inverter is not reported in literature yet. Detailed analysis and design of the proposed direct current-fed single-phase unfolding inverter has been presented. Simulation waveforms using PSIM 9.0.4 are given to verify the presented analysis and design. Experimental results on a laboratory prototype rated at 200 W are demonstrated to support the investigation, to validate the accuracy of the proposed analysis and design, and to test the performance. [ABSTRACT FROM PUBLISHER]

The main contribution of this paper is the derivation rules summarized from existing high-performance inverters with H6-type configuration, which makes novel topologies possible. In addition, a novel high-efficiency single-phase transformerless photovoltaic inverter with hybrid modulation method is also proposed and evaluated as an example. Without input split capacitors, common-mode voltage and leakage current issues in a nonisolated system with H6-type configuration are eliminated, and the feature of a three-level output voltage in the inverter bridge's middle point helps inductors and power quality optimization. The detailed operation principles with hybrid modulation strategy combined with unipolar and bipolar pulsewidth modulation schemes are presented. Experimental results of a 2200VA prototype verify the proposed topology with hybrid modulation method. [ABSTRACT FROM PUBLISHER]

In this paper, a novel single-phase five-level inverter is proposed using coupled inductors. This inverter can output five-level voltage with only one dc source. No split of the dc voltage capacitor is needed, totally avoiding the voltage balancing problem in conventional multilevel inverters. The level of the output voltage is only half of the dc-link voltage in all conditions, leading to much reduced dv/dt . This inverter is based on the widely used three-arm power module and the voltage stresses on all the power switches are the same, making it very easy to construct. Operation mechanism of this inverter is analyzed and the possible switching patterns are investigated. Based on these analyses, a novel optimized modulation scheme is presented. With this modulation method, no dc components exist in the inductor currents, which is very helpful for minimization of the inductors. Simulation and experimental results show the validity of the proposed inverter together with the optimized modulation scheme. [ABSTRACT FROM AUTHOR]

A novel H-bridge multilevel pulsewidth modulation converter topology based on a series connection of a high-voltage diode-clamped inverter and a low-voltage conventional inverter is proposed in this paper. A dc link voltage arrangement for the new hybrid and asymmetric solution is presented to have a maximum number of output voltage levels by preserving the adjacent switching vectors between voltage levels. Hence, a 15-level hybrid converter can be attained with a minimum number of power components. A comparative study has been carried out to present high performance of the proposed configuration to approach a very low total harmonic distortion of voltage and current, which leads to the possible elimination of the output filter. Regarding the proposed configuration, a new cascade inverter is verified by cascading an asymmetrical diode-clamped inverter, in which 19 levels can be synthesized in output voltage with the same number of components. To balance the dc link capacitor voltages for the maximum output voltage resolution as well as synthesize asymmetrical dc link combination, a new multi-output boost converter is utilized at the dc link voltage of a seven-level H-bridge diode-clamped inverter. Simulation and hardware results based on different modulations are presented to confirm the validity of the proposed approach to achieve a high-quality output voltage. [ABSTRACT FROM PUBLISHER]

The output voltage quality of some of the single-phase multilevel inverters can be improved when their dc-link voltages are regulated asymmetrically. Symmetrical and asymmetrical multilevel diode-clamped inverters have the problem of dc-link capacitor voltage balancing, especially when power factor of the load is close to unity. In this paper, a new single-inductor multi-output dc/dc converter is proposed that can control the dc-link voltages of a single-phase diode-clamped inverter asymmetrically to achieve voltage quality enhancement. The circuit of the presented converter is explained and the main equations are developed. A control strategy is proposed and explained in details. To validate the versatility of the proposed combination of the suggested dc–dc converter and the asymmetrical four-level diode-clamped inverter (ADCI), simulations and experiments have been directed. It is concluded that the proposed combination of introduced multioutput dc–dc converter and single-phase ADCI is a good candidate for power conversion in residential photovoltaic (PV) utilization. [ABSTRACT FROM PUBLISHER]