Search

This paper proposes an electronic driver for public lighting systems. The input stage is based on the integration of two flyback converters with different polarities, in order to avoid the use of the input diode bridge rectifying stage. The output stage is a boost converter with an output current control. The proposed circuit is introduced and analyzed, and a design example for a 50-W light-emitting diode lamp is presented. The most relevant simulation and experimental results are also shown, in order to validate the idea. A comparison in terms of efficiency for the input stage is carried out between the proposed topology and the conventional flyback converter, showing an efficiency enhancement in the proposed converter. However, the most important advantage of the proposed converter is outlined in the final part of this paper. This advantage comes from the avoidance of the input diode bridge, thus enabling the bidirectional power flow at the input stage. Therefore, the topology can be used to deliver energy into the power grid. In recent lighting applications, the use of micro renewable generators in lighting points has made the use of special electronics to handle the energy flows in the ballast necessary. The present topology is an alternative to standard bidirectional input stages. [ABSTRACT FROM AUTHOR]

A new three-phase single-stage rectifier is proposed in this paper. The outstanding features of the proposed rectifier are that it can produce input currents that do not have deadband regions and an output current that can be continuous when the converter is operating from maximum load to at least half of the load. In this paper, the operation of the new converter is explained, its features and design are discussed in results, and its operation is confirmed with experimental results obtained from a prototype. [ABSTRACT FROM PUBLISHER]

Multilevel inverters are receiving more attentions nowadays as one of preferred solutions for medium- and high-power applications. As one of the most popular hybrid multilevel inverter topologies, the five-level active-neutral-point-clamped inverter (5L-ANPC) combines the features of the conventional flying-capacitor type and neutral-point-clamped (NPC) type inverter and was commercially used for industrial applications. In order to further decrease the number of active switches, this paper proposes a seven-switch 5L-ANPC (7S-5L-ANPC) topology, which employs only seven active switches and two discrete diodes. The analysis has shown a lower current rating can be selected for the seventh switch under high power factor condition, which is verified by simulation results. The modulation strategy for 7S-5L-ANPC inverter is discussed. A 1 kVA single-phase experimental prototype is built to verify the validity and flexibility of the proposed topology and modulation method. [ABSTRACT FROM AUTHOR]

Interleaving is a technique that is commonly used due to its inherent reduction of current ripple and filter capacitance size. However, optimal interleaving is only achieved when the switching cells are identical. Variations of the filter inductance, which are caused by the manufacturing process or magnetic material properties, may lead to the total current ripple of all phases significantly larger than that of the ideal case in steady state, and slow down the energy transfer speed during the transient response. Consequently, in order to meet the voltage ripple and dynamic response requirements of multiphase converters, the calculation of the output capacitor under inductance mismatches has to be reconsidered, which has been rarely mentioned previously. This paper proposes a method to estimate the effect of inductance mismatches on output capacitance selection from two aspects including steady state and transient state. The proposed methodology enables mathematical expressions that allow us to calculate the maximum value of the capacitor considering nonidealities. Monte Carlo simulation is also used during the analysis by varying all of the inductors’ values with respect to tolerance and distribution type to identify the worst case values in real applications, according to this approach, the principle of when the worst condition happens is summarized. Simulated and experimental results of a four-phase buck converter are presented in this study. Good agreement between the estimates and the measured values is demonstrated. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC or M2C) is an emerging attractive multilevel topology for medium-voltage high-power applications. The capacitor voltage balancing control and the improvement of output current rating are two challenging issues of MMC. This paper proposed a new parallel-connected diode-clamped M2C (DCM2C), in which each arm consists of two parallel-connected clusters. In this topology, the capacitor voltages can be balanced automatically without any balancing control algorithms. Theoretically, no voltage sensors are needed to measure the capacitor voltages theoretically. Thus, the control of the converter can be simplified greatly. With a simple current-sharing control, an equal current distribution can be achieved between the two clusters. Furthermore, an extended parallel-DCM2C is proposed for larger current applications, and the corresponding current-sharing control method is developed. Experimental results validated the voltage self-balancing capability of parallel-DCM2C and the effectiveness of the proposed current-sharing control. [ABSTRACT FROM PUBLISHER]

A microconverter serves as a front-end dc–dc stage of a microinverter to convert the power from a photovoltaic module to a dc bus. These front-end microconverters require isolation, high-boost ratio, wide-input voltage regulation, and high efficiency. This paper introduces an isolated resonant converter with hybrid modes of operation to achieve wide-input regulation while still maintaining high efficiency. The proposed converter is designed as a series resonant converter with nominal-input voltage and operates under two additional modes: a boost converter with low-input voltage and a buck converter with high-input voltage. Unlike conventional resonant converters, this converter operates at discontinues conduction mode with a fixed frequency, simplifying the design and control. In addition, this converter can achieve zero-voltage switching (ZVS) and/or zero-current switching (ZCS) of the primary-side MOSFETs, ZVS and/or ZCS of the secondary-side MOSFETs, and ZCS of output diodes under all operating conditions. Experimental results using a 300-W prototype achieve a peak efficiency of 98.1% and a California Energy Commission efficiency of 97.6% including all auxiliary and control power at nominal-input voltage. [ABSTRACT FROM PUBLISHER]

A recently reported modeling methods for a switched capacitor converter either assume output as “firm” voltage or a resistor to facilitate calculation. When the size of output filter capacitor is moderate, accompanied by noticeable output ripple, previous modeling results may not provide accurate prediction and design guidelines. In this paper, a new modeling technique taking into account the output capacitor effect is proposed for simple dual-phase switched capacitor converters without complex coupling loops. The proposed model employs transient calculation, takes charge redistribution phase into account, and includes the duty cycle, switching frequency as well as output capacitor simultaneously in the final output impedance formula, which enhances accuracy of the model. It is suitable for interleaved and noninterleaved switched capacitor converters. The simulation and experimental results for the unity gain SC converter are provided to verify the proposed theory. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase hybrid cascaded modular multilevel inverter topology which is derived from the proposed modified H-bridge module. This topology results in the reduction of number of power switches, losses, installation area, voltage stress and converter cost. For renewable energy environment such as photovoltaic (PV) connected to the microgrid system, it enables the tranformerless operation and enhances the power quality. This multilevel inverter is an effective and efficient power electronic interface strategy for renewable energy systems. The basic operation of single module and the proposed cascaded hybrid topology is explained. The ability to operate in both symmetrical and asymmetrical modes is analyzed. The comparative analysis is done with classical cascaded H-bridge and flying capacitor multilevel inverters. The nearest level control method is employed to generate the gating signals for the power semiconductor switches. To verify the applicability and performance of the proposed structure in PV renewable energy environment, simulation results are carried out by MATLAB/Simulink under both steady-state and dynamic conditions. Experimental results are presented to validate the simulation results. [ABSTRACT FROM AUTHOR]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

This paper proposes a new power conversion scheme for paralleled server power supplies. The snubber capacitor voltage is utilized for the secondary voltage source, from which bidirectional buck converter provides output power to the load under a very light-load condition. To increase the energy of the secondary voltage source, an additional voltage bus is connected between the snubber capacitors from each power supply. The main advantage of the proposed scheme is that high efficiency can be achieved especially under a very light-load condition because of the low switching and core loss achieved by using the buck converter instead of the conventional structure composed of a primary inverter, an isolation transformer, and a secondary rectifier. Furthermore, the buck converter is integrated into the secondary rectifier circuits, so additional components are minimized. The validity of the proposed converter is confirmed by the experimental results from two 12-V/750-W prototype modules. [ABSTRACT FROM PUBLISHER]

Input-series output-series (ISOS) modular dc–dc converters are suitable for applications involving high input and output voltages. Input voltage sharing (IVS) and output voltage sharing (OVS) of the constituent modules must be guaranteed for an ISOS system. A duty cycle-based model predictive control (DC-MPC) scheme is proposed in this paper to achieve IVS and OVS for an ISOS system. The employed switching frequency in the DC-MPC scheme is fixed; duty cycles are optimized and then determined by minimizing a cost function, which is derived from an ISOS system aimed at achieving IVS and OVS. IVS and OVS can, therefore, be obtained by employing the optimized duty cycle within each sampling period. In addition, challenges and disadvantages of directly using traditional MPC to achieve IVS and OVS is briefly discussed, while the proposed DC-MPC can effectively avoid them. Compared with the existing proportional integral-based schemes in the literature, the proposed DC-MPC is better for IVS and OVS because it is a very simple and intuitive approach with lower cost and higher overall dynamic performance. Simulation and experiments are conducted to verify that the proposed DC-MPC scheme works well during both steady and transient states. [ABSTRACT FROM AUTHOR]

This paper presents a fault-tolerant configuration for the modular multilevel converter (MMC). The procedure is able to detect faults in voltage sensors and semiconductor switching devices, and it can reconfigure the system so that it can keep on operating. Both switch and sensor faults can be detected by comparing the output voltage of a set of submodules (SMs), which is measured by a so-called supervisory sensor, with two calculated reference voltages. Faults in the supervisory sensors are also considered. Sensor faults are overcome by using a measuring technique based on estimates that are periodically updated with the voltage measurements of the supervisory sensors. Additional SMs are included in the arms so that the MMC can bypass a faulty SM and continue operating without affecting the output voltage of the phase-leg. Experimental results obtained from a low-power MMC prototype are presented in order to demonstrate the effectiveness of the proposed techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a novel high step-up nonisolated single switch dc–dc converter suitable for regulating dc bus in various microsources especially for photovoltaic (PV) sources. Quadratic boost and switched-capacitor technique are used as primary and secondary circuits, respectively. A coupled inductor is applied to make a connection between them, so a high dc voltage gain is achieved. High efficiency is yield where voltage stress on active switch is alleviated by clamped capacitor; consequently, smaller \rmR\rm{DS(ON)} for power switch is required. On the other hand, input current of the proposed converter is continued, hence stress on the input source is reduced. The operating principles and steady-state analyses are discussed in detail for both continuous and discontinuous conduction modes. Also, the boundary condition is computed. To verify the performance of the proposed converter and theoretical calculations, a 250-W prototype converter is implemented with an input voltage of 24 V and an output voltage of 400 V designed especially for PV sources in continuous conduction mode operation. Finally, simulation results are confirmed by experimental results; maximum efficiency is occurred at 150 W and full-load efficiency is 92.96%. [ABSTRACT FROM AUTHOR]

In this paper, a new isolated high step-up dc–dc converter is proposed based on the quasi-switched-boost network. The proposed converter has the following features: 1) continuous input current; 2) reduced turn ratio of the isolated transformer; 3) increased reliability, as it can operate in either short-circuit mode or open-circuit mode without causing damage to the power converter; and 4) unchanged primary and secondary voltage waveforms of the transformer, although the shoot-through duty cycle is variable. Compared to the quasi-Z-source-based isolated dc–dc converter, the proposed converter uses fewer passive components. The operating principles, analysis, parameter design guideline, and comparison with the quasi-Z-source-based isolated dc–dc converter are presented. A 450 W prototype is built to test the proposed converter. The proposed converter is applicable for distributed power generation applications where a varying low dc input voltage is converted to a high stabilized dc output voltage with a galvanic separation requirement. [ABSTRACT FROM AUTHOR]

The reduced capability of multilevel converters with more than one intermediate node to balance the dc-link capacitors voltage, as well as the lack of standard modulation methods to improve their balancing performance, makes these converter topologies unattractive for real power applications. This is especially true when the load demands active power. One of these topologies is the five-level multipoint clamped (5L-MPC) converter. The back-to-back (B2B) configuration of two 5L-MPC converters and the use of a space vector modulation (SVM) that exploits the voltage balancing capability of the redundant switching vectors extend the operation conditions range in which a proper voltage balance can be achieved. However, if practical modulation restrictions are considered (limitation of voltage steps, dead times, switching losses, etc.), the voltage balance cannot be achieved for all operation conditions. In this paper, an SVM which takes into account practical restrictions is proposed. In order to guarantee the voltage balance at any operation condition, the grid-side rectifier exchanges reactive power with the grid-side LCL filter. Thus, the voltage balance of the dc-link is guaranteed while a unity grid-side power factor is achieved. The proposed modulation scheme and the voltage balancing strategy are experimentally validated in a 6.6 kV 1.5 MW 5L-MPC B2B converter. [ABSTRACT FROM AUTHOR]

This paper proposes a new configuration for static ground power unit (GPU) based on the novel 25-level hybrid active neutral-point-clamped (HANPC) converter. The superiority of the proposed converter, as compared with conventional and other suggested multilevel converters, is significant decreasing the number of switches and minimizing the number of flying capacitors (FC) in converter. This improvement is possible by using suggested low-voltage submodule converter to the ANPC converter and proposed modulation method. This results in reduction of the size and cost of converter and makes it more feasible and reliable. Applying the active voltage balancing method for FC in the proposed HANPC converter guaranties fast charging and voltage-level regulation of FC without using balance booster circuit. Improving output voltage spectrum leads to inductance reduction of output L–C filter which enhances static GPU performance. The simulation and experimental results verify the validity and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

A new cascade topology for multilevel converter is introduced in this paper which comprises series connection of several submultilevel units. To determine the magnitudes of the dc sources, two new methods are described. The proposed topology is optimized to generate any levels with minimum number of components and peak voltage on switches. The presented topology can be used in high-voltage applications due to using the switches with low voltage rating. To indicate the merits of the proposed structure, comparison studies are provided with other topologies in terms of the number of elements and peak voltage on switches. The comparison results prove that the presented cascade multilevel converter requires fewer components. Moreover, it is shown that the total peak voltage on switches in the proposed topology is less than other structures. Experimental work is presented to demonstrate the performance of the presented multilevel converter. [ABSTRACT FROM PUBLISHER]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a quasi-Z-source integrated multiport converter (ZIMPC) for switched reluctance motor (SRM) drives to reduce the dc-link capacitance and enable wide-speed-range operation. In conventional SRM drives, employing multiphase asymmetrical H-bridge (ASHB) topology, large capacitors are necessary to absorb the transient energy during phase current commutation. However, electrolytic capacitors would affect the lifetime, cost, and power density of the drive system. With switch multiplexing technique, a ZIMPC is derived to achieve power ripple reduction using relatively small capacitors. The power ripple generation principle and requirement of capacitance in ASHB and ZIMPC are analyzed. The model of the overall system including SRM and the proposed drive is developed using mode analysis. Advanced control method with repetitive control is proposed and developed based on the system model. Also, the ZIMPC can boost the equivalent phase exciting voltage and widen the constant power speed range. At last, simulation and experimental results verify the feasibility of the proposed ZIMPC and its superior performance with smaller capacitance as compared with ASHB. [ABSTRACT FROM PUBLISHER]

Modular multilevel converters (MMCs) for high-power applications may contain over a thousand submodules. In work such as submodule design or innovation to build a full system with as many levels to test the submodule is time consuming and costly. To solve the problem, testing schemes are being developed to allow an individual submodule to be tested without a complete MMC. This paper presents a new submodule testing scheme that builds on a recent development to improve the testing capability. The improved structure is introduced along with design and control techniques. A design example of a test platform to test SMs with 2000-V rated voltage is introduced, which only requires a 545-V dc supply. The voltage testing capability is increased by more than five times when compared with the original scheme. In addition, simulation results show that the proposed method can offer better current tracking accuracy than the original with the same parameter settings. A prototype test platform, designed to test submodules with 400-V rated voltage and 14-A current, has been built and tested experimentally in order to verify the design. [ABSTRACT FROM PUBLISHER]

Conventional matrix converters (MCs) have limited voltage gain that is less than 0.866, whether for direct MC (DMC) or indirect MC (IMC). The Z-source MCs (ZSMCs) overcome the voltage gain limitation of the traditional MC and achieve buck and boost operation with reduced switches count, thereby achieving low cost, high efficiency, and reliability, compared to the back-to-back converter. Furthermore, it will leads to more MC industrial applications. This paper presents an up-to-date comprehensive overview of the different ZSMC topologies and their configurations, circuit analyses, modulation schemes, and applications. This study offers a comprehensive and systematic reference for the future development of the ZSMCs. [ABSTRACT FROM PUBLISHER]

In this paper, a novel four-phase interleaved high step-down converter is presented. The proposed converter can provide an extremely high step-down voltage conversion ratio within a moderate duty cycle. There are four main advantages of the proposed converter. First, the blocking capacitors can store energy as usual. Therefore, they are used as voltage sources to reduce the input voltage as well as to reduce the switch voltage stresses. Second, due to the charge balance of the dc blocking capacitors, the converter possesses an automatic uniform current sharing characteristic of the interleaved phases without adopting any extra circuitry. Third, due to the phase shift between the interleaved phases, the architecture provides a low output current ripple. Fourth, the number of phases can be expanded or reduced to any even phases; therefore, the converter has a wide range of applications. Finally, the operating principles and analysis of this architecture are given, and an experimental prototype is also provided to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

The model predictive control has an ability to achieve multiple control objectives for a modular multilevel converter. This approach has high computational complexity and causes the unwanted switching's leading to a higher ripple in output current and harmonic distortion in output voltage and current waveforms. To solve the issues of computational burden and unwanted switchings, this paper proposes a dual-stage model predictive control approach for a modular multilevel converter. In this approach, the primary objectives are evaluated in first stage corresponding to the redundancy of voltage vectors, while the secondary objectives are evaluated in second stage corresponding to the submodule redundancy. Therefore, the computational burden is significantly minimized without affecting the dynamic response. In addition, a discrete-time model of modular multilevel converter incorporating the common-mode voltage is proposed. The simulation and experimental studies are conducted on a three-phase modular multilevel converter to verify the dynamic and steady-state performance of the proposed approach. The performance comparison between the proposed and conventional model predictive control approach is also presented. [ABSTRACT FROM PUBLISHER]

Two new configurations of static ground power unit based on 5L active neutral point clamped (ANPC) and novel modular 9L-ANPC converter are proposed. First, a new level shifted phase-shifted carrier pulse-width modulation (LS-PSC-PWM) switching method for the 5L-ANPC converter is defined. By utilizing the proposed method, total harmonic distortion of output voltage is reduced in comparison with traditional PSC-PWM switching method. Then, a novel modular 9L-ANPC multilevel converter and its suggested modulation method is proposed in this paper. In comparison with traditional 9L-ANPC converter, the main advantages of proposed modular 9L-ANPC converter are halving the applied voltages on flying capacitors (FC), reduced number of FCs, and self-balancing of FCs, which is provided by suggested switching method. This results in reduction of the size and cost of converter, and makes it more feasible and reliable. Furthermore, inductance reduction of output LC filter enhances static ground power unit dynamic performances. The simulation and experimental results verified the feasibility and performance of proposed converters. [ABSTRACT FROM PUBLISHER]

A multilevel boost power factor correction (PFC) rectifier is presented in this paper controlled by cascaded controller and multicarrier pulse width modulation technique. The presented topology has less active semiconductor switches compared to similar ones reducing the number of required gate drives that would shrink the manufactured box significantly. A simple controller has been implemented on the studied converter to generate a constant voltage at the output while generating a five-level voltage waveform at the input without connecting the load to the neutral point of the dc bus capacitors. Multicarrier pulse-width modulation technique has been used to produce switching pulses from control signal at a fixed switching frequency. Multilevel voltage waveform harmonics has been analyzed comprehensively which affects the harmonic contents of input current and the size of required filters directly. Full experimental results confirm the good dynamic performance of the proposed five-level PFC boost rectifier in delivering power from ac grid to the dc loads while correcting the power factor at the ac side as well as reducing the current harmonics remarkably. [ABSTRACT FROM PUBLISHER]

This paper provides a characterizationr analysis for the voltage balance of modular cascaded converter in a medium-voltage direct-current distribution grid. Specifically, voltage stability and traditional auxiliary resistor solution are analyzed from the theoretical level. On this basis, a minimum voltage tracking balance (MVTB) control based on a switched resistor is proposed. The voltage balance during startup and normal locked processes can be adjusted effectively by MVTB control. Moreover, the resistor does not need to absorb power continuously; instead, it is just switched into operation for a while when a difference occurs, and the power loss can be decreased after the system recovers to a steady state. Finally, experimental results verify the effectiveness of the MVTB control. [ABSTRACT FROM PUBLISHER]

This paper proposes an optimal design method of modular multilevel converter (MMC) levels to approach the reasonable compromise between accuracy and computational efficiency. The entire procedure is benchmarked by a Thévenin equivalent 451-level MMC model. First, the calculation method of the critical maximum simulation time step is proposed to faithfully represent each voltage level of the staircase waveforms. Second, the previously developed improved analytic hierarchy process is adopted to integrate the relative errors of all the main electrical parameters into one comprehensive relative error at each MMC level. Third, the steady state, ac, and dc transient state relative error results as well as the central-processing unit times of all models are normalized and curve fitted based on the benchmark model. Finally, the optimal MMC level is obtained by the plotted curves and the given subjective weights considering the accuracy and efficiency. And the effectiveness and robustness of the proposed method are validated by various simulation scenarios on PSCAD/EMTDC. [ABSTRACT FROM PUBLISHER]

A new resonant converter having low voltage stress and nearly constant efficiency against line variation for high- and wide-input-voltage applications is presented in this paper. It is similar to a three-level zero-voltage-switching pulsewidth modulation converter (TL ZVS PWMC) with two flying capacitors. In the proposed converter, however, two flying capacitors are used as the resonant capacitors, and the output voltage regulation is achieved by frequency modulation. The main advantages of the proposed converter are that, since the sum of the voltages of two resonant capacitors is constant and is equal to half of the input voltage, the voltage across each switch clamps to half of the input voltage and keeps the balance. Moreover, all main switches and rectifier diodes are softly switched under full-line and full-load conditions, and high efficiency can be constantly achieved over a wide input voltage range. These advantages solve the drawbacks on TL ZVS PWMCs. The features, operation principles, and relevant analysis results over a wide input voltage range of the proposed converter are presented in this paper. The validity of this study is confirmed by the experimental results of a prototype converter with 400–600-V input, 48-V/10-A output, and 200-kHz resonant frequency. The experimental results show that the maximum efficiency of the proposed converter is 95.08% under a full-load and a 600-V input and slightly varies across the 400–600-V input voltage range. [ABSTRACT FROM AUTHOR]

This paper proposes an isolated universal-link ac–ac power converter suitable for grid connection. The proposed power converter can have multiple ports to connect various loads or electric energy sources, and the configuration can be arranged according to the situation. The proposed power converter does not need to employ the large interface inductor at input side and the huge electrolytic capacitor at dc link. Moreover, it utilizes high-frequency transformers for the galvanic isolation instead of bulky line-frequency transformers. These characteristics of the proposed power converter result in the reduction of the system volume and weight remarkably. The proposed power converter is the modular structure, and an H-bridge works as a basic module of the converter. By stacking the modules, the power converter can be adapted to the high-voltage grid and the various types of loads and/or sources. This paper addresses the structure of the proposed power converter and the fundamental principle of power flow. The operation of the proposed converter is verified by both computer simulations and experimental results with a laboratory-level prototype system. [ABSTRACT FROM AUTHOR]

Multimodule converter-based high-voltage dc (HVDC) power transmission incorporates numerous voltage-source converters (VSCs) connected in series/parallel to provide increased voltage/current and, hence, power ratings. When a selective harmonic elimination pulsewidth-modulation (SHE-PWM) technique is employed, the switching losses of the VSC modules are reduced but the voltages of the series-connected dc capacitors are not naturally balanced. In this paper, a voltage-balancing technique is reported. The technique relies on monitoring the voltage of each dc capacitor and when such voltage exceeds its preset band, the realization of the multilevel waveform reallocates the task to another VSC module to ensure that voltage balance between all capacitors is achieved. Three-phase bipolar VSC modules are considered in this paper and each one is modulated by a precalculated multilevel SHE-PWM waveform. The time-domain waveforms and their line-to-line voltage spectra are verified by simulation using PSCAD/EMTDC. The selected results are presented to confirm the viability of the proposed method. [ABSTRACT FROM PUBLISHER]

First, the limitations of the conventional interleaved boost converters in high-step-up and high-output-voltage applications are addressed in this paper. Then, a general derivation law of the nonisolated converters from their isolated counterparts is proposed and studied to give a universal solution for high-performance topology deduction. By employing the direct energy transfer concept, a family of nonisolated high-step-up interleaved boost converters is originated to make the turns ratio of a built-in transformer as another design freedom for the voltage gain extension. The derived converters have the advantages of large voltage conversion ratio, low power switch voltage stress, small input current ripple, and zero-voltage-switching soft-switching performance. The steady-state operation of the derived converter is analyzed, and the circuit performance is summarized to explore its advantages in the high-step-up, high-output-voltage, and large-current conversion systems. Finally, a 1-kW prototype with 40-V input and 380-V output voltages is implemented and tested to show the effectiveness of the derived converters. One of the main contributions of this paper is that a clear picture is made on the universal derivation law to generate high-step-up and high-performance dc/dc converters. [ABSTRACT FROM PUBLISHER]

The matrix converter can be used in a wide range of applications. Nevertheless, it does not yet represent a sufficiently mature option for industrialization. In order to resolve this problem, this paper examines the hardware of the matrix converter and identifies all the circuits that should be included in this. It also quantifies the operating conditions and provides practical guidelines for the step-by-step design of a matrix converter. These considerations are validated with experimental results. In this way, it can be said that this paper represents a step forward toward the development of reliable matrix converters for real applications. [ABSTRACT FROM AUTHOR]

This paper proposes a novel family of cascade three-level (TL) ac–ac direct converters based on ac switch cells, which transfer unsteady high ac voltage with distortion into regulated sinusoidal voltage with low total harmonic distortion (THD). The topological family includes buck TL–boost, buck–boost TL, and buck TL–boost TL modes. In order to achieve a reliable TL ac–ac conversion, a double transient voltage feedback control strategy of the output voltage and the voltage across the flying capacitor is introduced in this paper. A 500-VA 220-V \pm10% 50-Hz ac/220-V 50-Hz ac prototype is presented with the experimental results to prove that the converters have four improved advantages simultaneously, including lower voltage across power switches, bidirectional power flow, low THD of output voltage, and higher input power factor. [ABSTRACT FROM AUTHOR]

Multilevel power electronic converters have gained popularity in high-power applications due to their lower switch voltage stress and modularity. Cascaded H-bridge converters are a promising breed of multilevel converters which generally require several separate dc voltage sources. By utilizing the redundant switching states, it is possible to replace the separate dc voltage sources with capacitors and keep only the one with the highest voltage level. Redundancy in the charge and discharge modes of the capacitors is assumed to be adequate for their voltage regulation. However, the effects of the output current of the converter as well as the time duration of the redundant switching states have been neglected. In this paper, the impacts of the connected load to the cascaded H-bridge converter as well as the switching angles on the voltage regulation of the capacitors are studied. This paper proves that voltage regulation is only attainable in a much limited operating conditions that it was originally reported. In addition, based on the analysis of the converter, a simplified formula is found which can be used to find those modulation indices that regulate the voltage of the capacitor. This formula can be used in harmonic minimization problems while capacitor voltage regulation is ensured. Simulation and laboratory results are provided to confirm the analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a new circuit topology for a multilevel pulse width modulation (PWM) rectifier. The proposed method forms a new circuit by combining a diode clamp-type topology with a flying capacitor-type topology. The proposed circuit uses only 12 switches, despite the use of a five-level three-phase PWM rectifier. Further, the proposed circuit can obtain good performance, same as a conventional multilevel circuit. This paper describes about the features of the proposed topology; the control strategy and the loss analysis that is estimated by a circuit simulator. In addition, the basic operation of the proposed method is confirmed by simulation and experimental results. The proposed converter achieved total harmonic distortion of 3.4% for the input current and efficiency of 97.4% for a 1 kW class experimental setup. [ABSTRACT FROM AUTHOR]

This paper proposes a three-phase, reduced-switch, buck-type converter that can operate with input-power-factor correction. The key feature of the proposed converter is that a switch in the converter has a lower peak voltage stress than a switch in a conventional three-phase, single-switch buck converter. The voltage stress in the proposed converter is limited to the peak value of the phase voltage of the input capacitors rather than the peak value of the line-to-line voltage, as is the case in the conventional converter. The reduction in the voltage stresses is therefore almost half as compared to that of conventional converter. This allows lower rated, standard devices to be used in the converters and reduces switching losses. In this paper, the steady-state operation of the converter is presented and general properties and design considerations are discussed. The feasibility of the proposed converter is confirmed with results obtained from an experimental prototype. [ABSTRACT FROM PUBLISHER]

This paper introduces a new magnetically coupled single-switch nonisolated dc–dc converter with a high-voltage gain. The topology utilizes magnetic coupling for boosting its output voltage, but unlike other converters with coupled magnetics, its voltage gain is increased by reducing its magnetic turns ratio. The name “Trans-inverse (Tx−1)” is thus used for representing this inverse operating principle of the converter. The converter draws a continuous current from the source and is, hence, suitable for many types of renewable sources. Its leakage energy from the coupled magnetics has further been recycled and transferred to the load by an integrated regenerative snubber circuit. Its inclusion of dc-current-blocking capacitors has also helped to prevent core saturation, which, together with other performance features, has been verified experimentally. [ABSTRACT FROM PUBLISHER]

In this paper, a cascaded H-Bridge (CHB)-multilevel converter (MC)-based photovoltaic (PV) system with no voltage or current sensors at the dc-side is proposed. Eliminating the dc-side sensors simplifies the hardware, leading to lower cost and higher reliability of the PV system. A novel scheme estimating the capacitors’ voltages from the ac output voltage of the inverter is developed. The scheme allows replacing all dc-side voltage sensors by a single-voltage sensor at the ac-side of the converter. Furthermore, the dc current sensors, conventionally required for the maximum power point tracking (MPPT), are also eliminated. Instead, the outputs from the capacitors’ voltage control systems are utilized for the MPPT. The effectiveness of the proposed dc-side sensorless system is experimentally demonstrated on a 2-kW single-phase seven-level CHB converter-based PV system. [ABSTRACT FROM PUBLISHER]

This paper presents a new dual-switch control structure for an ac/dc noninverting cascaded buck–boost power factor correction converter. The proposed converter operates at a discontinuous capacitor voltage mode providing an inherent high-power factor and a zero voltage turn-off switching. Additionally, the proposed control structure enables for a nondistorted sinusoidal current for a wide range of output voltage levels. Unlike the conventional methods, a mode detector is not required and consequently there is no hard transition between buck and boost modes. Although both converter switches are controlled, only one feedback control loop is required to obtain the desired power flow at a unity power factor. The principle of operation, theoretical analysis, simulation, and experimental results of a 1.6-kW prototype grid-connected converter are presented. The results confirmed the validity of the proposed system under various operating conditions. [ABSTRACT FROM PUBLISHER]

Switched-capacitor (SC) converters were initially introduced for low-power applications and monolithic integration. In recent years, SC converter has found high-power applications. However, voltage regulation remains an issue. This paper addresses regulation challenges for high-power SC converters, based on charge-balance transient-calculation (CT) modeling method and peak current stress estimation. With the help of CT model, due to its accuracy and comprehensive relationship, circuit and control parameters’ impacts on regulation become straightforward and concerns on components stresses can be addressed quantitatively. The suitability of CT method for regulation analysis is confirmed by comparison with traditional modeling methods. The CT method is used in a 1-kW 3X two-switch boosting switched-capacitor converter (TBSC) circuit for steady-state analysis and current stress estimation. The soft rising input current and nature interleaving properties of 3X TBSC make it well suited for high-power application. Finally, the small-signal model of the 3X TBSC is developed and a closed-loop operation is achieved under 1 kW power rating. [ABSTRACT FROM AUTHOR]

This paper provides theoretical and experimental discussions on an optimal carrier frequency for a phase-shifted pulsewidth modulation modular multilevel cascade converter for grid connections. The theoretical discussion concludes that a ratio of the optimal carrier frequency with respect to the supply (ac) frequency is 5/2. A three-phase downscaled front-to-front system is designed, constructed, and tested to confirm validity of the theoretical discussion. It consists of a pair of three-phase modular multilevel cascade converters rated at 400 Vdc and 10 kW, where the carrier frequency is set to 450 Hz and the ac frequency to 180 Hz, that is, their ratio is equal to 5/2. Moreover, simulated waveforms are compared to experimental ones under the same operating conditions. Both experimental and simulated waveforms agree well with each other not only in steady states but also in transient states. [ABSTRACT FROM AUTHOR]

A novel soft-switching PWM three-level (TL) dc–dc converter with two added secondary switches is proposed. The proposed converter has following good features: four primary switches sustain half of the input voltage; the primary circuit is simpler and more compact due to only one flying capacitor with smaller current stress is required to clamp off state voltage of the primary switches; the secondary rectified voltage before the output filter is a TL waveform, which significantly reduces the requirement of the output and input filters; all primary switches can obtain ZVS in wide load range. Furthermore, less conduction loss is added. The added secondary switches can obtain zero-current switching independent of the load current. The proposed converter can be extended to higher voltage level easily due to simpler and more compact primary structure. In addition, the presented converter is also well suitable for high-input dc interfaces with independent controllable multioutput ports. The operation principle, soft switching characteristics, and some important analyzes are presented in this paper. The proposed converter is verified by the experimental results from a 10-kW prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a power-factor-corrected canonical switching cell (CSC) converter-based switched-mode power supply for arc-welding applications. In the proposed arc-welding power supply (AWPS), CSC converter operating in discontinuous inductor current mode (DICM) is used to attain inherent power factor correction. The DICM operation substantially reduces the complexity of the control and effectively regulates the dc-link voltage. At the back end, a pulsewidth-modulated (PWM) isolated full bridge dc–dc converter is used to provide a high-frequency isolation, which is mandatory for the arc-welding process. A dual-loop control scheme is utilized to incorporate overcurrent protection and to regulate dc voltage at the output making it suitable for arc-welding applications. Test results are presented to confirm the viability of the proposed AWPS. The performance of the proposed AWPS is evaluated on the basis of total harmonic distortion (THD) of the supply current, power factor, dynamic response, and voltage regulation to prove its effectiveness. [ABSTRACT FROM PUBLISHER]

This paper proposes a current-fed non-isolated soft-switching bidirectional dc/dc converter for interfacing energy storage to dc microgrid. The proposed converter employs a current-fed half-bridge boost converter at front-end followed by an LCL resonant circuit to aid in soft-switching of semiconductor devices. A voltage doubler at output is selected to enhance the gain by $2 \times $. The LCL resonant circuit also adds a suitable voltage gain. Therefore, the topology offers overall high voltage gain without transformer or large number of multiplier circuits. For buck operation, high side voltage is first divided by half with capacitor divider to gain higher stepdown ratio. Converter operates at high switching frequency to realize merits of reduced magnetics and filters. Zero voltage turn-on is achieved for all switches and zero current turn-on and turn-off is achieved for all diodes for both buck/boost operation. Voltage across switches and diode is clamped naturally without any external snubber circuit. Detailed analysis and design have been proposed. A proof-of-concept experimental prototype rated at 350 W has been designed, developed, and tested in the laboratory to demonstrate the performance and validate the claims of the converter for wide load variation. [ABSTRACT FROM AUTHOR]

This paper proposes three dynamic voltage restorer (DVR) topologies. Such configurations are able to compensate voltage sags/swells in three-phase four-wire (3P4W) systems under balanced and unbalanced conditions. The proposed systems use two independent dc links. Proposed configurations present advantages in terms of switch blocking voltages and consequently lower dc-link voltage rating. The complete control system, including the pulsewidth modulation (PWM) technique, is developed, and comparisons between the proposed configurations and a conventional one are performed. Simulation and experimental results are provided to validate the theoretical approach. [ABSTRACT FROM AUTHOR]

This paper proposes a new vector-based dead-time compensation method for three-level T-type converters. The origins and effects of the dead-time voltage errors are analyzed in detail for different switching commutations and load conditions. In order to eliminate the dead-time distortion in each phase, a dead-time error voltage vector is introduced to adjust the reference voltage vector depending on load current polarity. The proposed vector-based dead-time compensation scheme has several advantages. First, it can be applied to multilevel converters with any number of voltage levels using any modulation schemes. Second, the pulse loss issue which is common in conventional pulse-based compensation strategies can be eliminated. In addition, the pulse saturation can be mitigated by operating the converters in overmodulation regions. All of these advantages and effectiveness of the proposed vector-based dead-time compensation method are verified through both simulation and experimental studies. [ABSTRACT FROM AUTHOR]

This paper presents a voltage regulator topology, implemented using low-voltage devices, for converting high input voltage (>4.5 V) to low output voltages with fine-grain control (0.3 to 1 V). The topology merges a Dickson's switched-capacitor stage with a current-mode inductive buck stage, and optimizes the frequency of operations to reduce the overall passive size. The proposed two-stage hybrid regulator, designed in 130-nm standard digital process, operates from 4.8 to 6 V at input and regulates output voltage as low as 0.3 V with a maximum output power of 90 mW and a peak efficiency of 69%. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-phase high-power-factor ac/dc converter with soft-switching characteristic. The circuit topology is derived by integrating a boost converter and a buck converter. The boost converter performs the function of power-factor correction to obtain high power factor and low current harmonics at the input line. The buck converter further regulates the dc-link voltage to provide a stable dc output voltage. Without using any active-clamp circuit or snubber circuit, the active switches of the proposed converter can achieve zero-voltage switching-on transition together with high power factor that satisfies the IEC 61000-3-2 standards over a wide load range from 30% to 100% rated power. The steady-state analysis is developed and a design example is provided. A prototype circuit of 60 W was built and tested. Experimental results verify the feasibility of the proposed circuit with satisfactory performance. [ABSTRACT FROM PUBLISHER]

An advanced hybrid LLC series resonant converter with integrated flying-capacitor cell is proposed in this paper to enable the high step-down conversion in the high input voltage applications. The inherent flying-capacitor branch in the primary side can effectively halve the primary switch voltage stress compared with the half-bridge LLC converters. And the input voltage can be shared equally and automatically between the two series half-bridge modules without additional balance circuit or control strategies due to the built-in flying-capacitor cell. Moreover, the inherent soft switching performance during wide load range that exists in the LLC converters is still kept to reduce the switching losses, which ensures the high efficiency. Besides, the proposed converter can be extended to further decrease the switch voltage stress by employing stacked connection. Finally, a 500 ∼ 640 V-input 48 V-output 1 kW prototype is built and tested to verify the effectiveness of the proposed converter. The results prove that the proposed converter is an excellent candidate for the high input voltage and high step-down dc/dc conversion systems. [ABSTRACT FROM PUBLISHER]