Search

In this paper, a single-inductor dual-output (SIDO) dc–dc converter is proposed. The significant feature of the proposed converter is feeding a constant power load in low-voltage side (LVS) port, where even feeding a variable load at LVS does not have any cross regulation to high-voltage side port with the desired approximation. Magnificently, both merits are obtained in open-loop manner, which is an outstanding characteristic in comparison with that of the existed converters. In this paper, soft commutation and soft switching of switches and diodes are investigated along with the aforementioned main novelty. Moreover, detailed theoretical analyses of the proposed SIDO dc–dc converter in continuous conduction mode are presented besides the comparisons with some other structures. Finally, theoretical analyses are verified through a 1500 W experimental prototype results. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

Reduced switch active phase converters (APC) are cost-effective solutions for running three-phase loads from single-phase grids. This paper proposes a novel auxiliary-capacitor-based APC (AC-APC) for this application. The combination of the topological location of the auxiliary capacitor and the control of the AC-APC reduces current stress on the semiconductor devices. In this paper, a selection criterion for the optimal auxiliary capacitor value is formulated to reduce the device currents in such a way that the overall efficiency is enhanced. This paper presents a comparative analysis of converter volt-ampere (VA) rating and device power loss for conventional H-bridge active front-end and inverter-based topology, APC, and AC-APC. To evaluate the efficacy of the proposed AC-APC, an experimental study is conducted on the APC and the AC-APC feeding a 3-hp three-phase induction motor. At a full load of $\text{2.5}\,\text{kW}$ and $\text{0.8 } \text{power factor}$ , the measured maximum efficiency of the AC-APC is $2\%$ higher than that of the APC. Analytical evaluation of converter currents and device power loss are in close agreement with experimental observations. [ABSTRACT FROM AUTHOR]

This paper studies the high power density bidirectional dc–dc converter with interleaving, soft-switching, and near critical conduction mode (near-CRM) operation. Systematic design and control methods are proposed to enhance the effectiveness of passive currents balancing between multiple interleaved phases without using individual phase current feedbacks. This paper first analyzes the zero voltage turn-on operation, including the turn-off energy diversion by the added snubber capacitor and the turn-off resonance models. Second, the intrinsic inverse co-relation between the phase current deviation and the resulting effective duty cycles variation is quantitatively formulated and modeled as a closed-loop mechanism that balances the currents passively. Then, the design constraints of the system parameters including the snubber capacitance, dead time, and valley currents of the near-CRM mode are formulated to guarantee the effectiveness of counteracting the current unbalance. Finally, a variable switching frequency control is proposed to actively control the valley current and maintain the current balancing effectiveness throughout the operating range. An IGBT-based 20-kW three-phase interleaved prototype with the maximum efficiency of 99.1% is constructed to verify the proposed design and control methods. [ABSTRACT FROM AUTHOR]

This paper proposes a new developed switched-capacitor converter to achieve high-voltage pulses with adjustable voltage level and frequency. The proposed topology generates repetitive high-voltage pulses by using low-voltage power supply with reduced number of components, including power semiconductors and capacitor. Therefore, a converter based on switched-capacitor units with high voltage gain and high efficiency can be achieved. Operation principles and design steps of the converter as well as comparative study with conventional converters are described in this paper. Finally, simulation and experimental results of a two-stage structure of the proposed circuit validate the operation principles and features of this topology. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dc power electronic transformer (DCPET) topology for locomotive, ac/dc hybrid grid, dc distribution grid, and other isolated medium-voltage and high-power applications. Compared with conventional PET topology, the proposed DCPET has fewer power semiconductor devices and high-frequency isolation transformers, which can improve the power density and reliability. Fault handling or redundancy design can be achieved to further improve the reliability when some dc–dc modules break down. Also, input voltage sharing control can be omitted to simplify the control system and improve the stability. Meanwhile, soft switching is guaranteed for all the switches, which is beneficial to increase switching frequency and improve power density. In this paper, the principle, evolution, and control of the proposed DCPET are respectively presented and studied in detail. Finally, a prototype of the proposed DCPET is built and the experimental results verify the validity and superiority of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a new six-level flying capacitor based (FC-based) multilevel converter with one dc source and the capability of operating in all power factors and modulation indexes. Multilevel converters with one dc voltage source are attractive in many applications as they do not need rather expensive and bulky multiwinding input transformer connection at the dc side. On the other hand, not all classic multilevel converters with one dc source can produce any desirable number of output voltage levels at all power factors and/or modulation indexes. In this paper, a hybrid structure is proposed in which six voltage levels can be realized at the ac terminals. The modulation technique and the control strategy for the FC voltage balancing are presented. To show the advantages of the proposed converter, different performance criteria, such as switch count and rating, the size of capacitors, switching frequency, and power losses, are compared with other existing six-level topologies. The results indicate that the proposed structure is superior to other six-level converters from different standpoints. Simulation results are used to further evaluate the performance of the proposed converter. A laboratory-type experimental setup is used to validate the theoretical results. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-down dc–dc converter with ultrahigh step-down conversion ratio is proposed. Advantages of the proposed converter are high step-down ratio, extended duty cycle, reduced switching losses by a converter operation under zero-voltage switching (ZVS) conditions, reduced reverse reco-very losses of diodes by achieved zero-current switching turn-off condition, and reduced voltage spikes by the inherent active-clamping structure of the converter. In this converter, series capacitors and coupled inductors have been used in power path to achieve the low voltage gain and extended duty cycle. By the inherent active-clamping structure of the proposed converter, the leakage inductance energy is totally recovered in the output; therefore, the high voltage spike across the semiconductor devices is suppressed. The switches of the proposed converter can operate under ZVS conditions, which cause reduced switching losses and improved efficiency. In this paper, the converter operating modes are discussed, and a prototype circuit is implemented. Experimental results are presented to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a new soft-switching bridgeless single-phase power factor correction (PFC) converter is presented and analyzed. Employing an auxiliary switch, the input current dead angle that is the main drawback of the existing buck-type PFCs is omitted, and thus, the power factor (PF) is improved, which is the main contribution of the paper. Proposed PFC converter operates under discontinuous conduction mode (DCM) and draws sinusoidal input current from power supply inherently. All switches and diodes are turnedonandoffunder soft switching, which leads to low switching losses and elimination of diode reverse recovery problems. Also, minimum numbers of semiconductor devices are in the power flow path that reduce the conduction losses. A 120-W laboratory prototype is implemented and experimental results verify the validity of theoretical analysis and show efficiency of 92.1%. In addition, total harmonic distortion (THD) of 3.3% is achieved and the input current harmonics complies with IEC61000-3-2 Class D requirements. [ABSTRACT FROM AUTHOR]

A high step-up dc–dc converter is proposed in this paper. The presented converter benefits from some advantages such as high voltage gain and continuous input current, which makes it suitable for the renewable energy applications. The presented converter is based on the SEPIC converter. However, the converter voltage gain is improved by employing a coupled inductor and two voltage multipliers. A passive clamp circuit is also added to the proposed converter that increases the voltage gain and reduces the voltage stress on the main switch. Thus, a switch with low $R_{{\text{DS(on)}}}$ will be needed that decreases the conduction loss. Besides, the voltage stress on the output diode in the proposed converter is reduced, which alleviates reverse recovery problem. The steady-state analysis of the proposed converter is discussed in this paper. The analysis is verified with experimental results under the output power of 245 W. [ABSTRACT FROM AUTHOR]

In this paper, a high step-up quasi-Z Source (QZS) dc–dc converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS dc–dc converter while keeping its main advantages, such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch is not increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based dc–dc converters is provided which confirms the superiority of the proposed converter. Simulations are done in power systems computer aided design (PSCAD) in order to investigate the maximum power point tracking (MPPT) capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype. [ABSTRACT FROM AUTHOR]

This paper introduces a non-isolated high step-up dc–dc converter with dual coupled inductors suitable for distributed generation applications. By implementing an input parallel connection, the proposed dc–dc structure inherits shared input current with low ripple, which also requires small capacitive filter at its input. Moreover, this topology can reach high voltage gain by using dual coupled inductors in series connection at the output stage. The proposed converter uses active clamp circuits with a shared clamp capacitor for the main switches. In addition to the active clamp circuit, the leakage energy is recycled to the output by using an integrated regenerative snubber. Indeed, these circuits allow soft-switching conditions, i.e., zero voltage switching and zero current switching for active and passive switching devices, respectively. The mentioned features along with a common ground connection of the input and output make the proposed topology a proper candidate for transformer-less grid-connected photovoltaic systems. The operating performance, analysis and mathematical derivations of the proposed dc–dc converter have been demonstrated in the paper. Moreover, the main features of the proposed converter have been verified through experimental results of a 1-kW laboratory prototype. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure of nonisolated boost dc–dc converters based on voltage-lift technique is proposed. In comparison with conventional nonisolated boost dc–dc converters, the proposed converter generates higher voltage gain. In this paper, the relations between voltage and current of all elements in continuous conduction mode and discontinuous conduction mode are calculated as well as voltage gain in each mode. Then, the critical inductance and stress of switch current are extracted. Finally, the validity of given theories is examined by using the experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a single-stage nonisolated switched capacitor ac–dc converter for power-factor correction (PFC). This converter features reduced passive components, single switch, transformerless high voltage gain, and improves the power factor, reduces total harmonic distortion, and voltage stress across the switch. The peak current mode with a dynamic resonant perturbation scheme compensates the subharmonics that exist at zero crossing of the source current is implemented for PFC. In this paper, the principle of operation, large signal modeling of the circuit, and control method for the proposed PFC converter are provided. [ABSTRACT FROM PUBLISHER]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

This paper proposes an analytical design procedure for the LLCL and the LCCL filters for grid integration of high-power voltage-source converters. The low switching frequency and stringent limits on grid-injected harmonics in high-power applications lead to large smoothing filters. In order to reduce the size and weight, high-order filters are already proposed and wise design procedures with the main goal of minimizing the overall filter size are being suggested. In this paper, the parameters of the LLCL and the LCCL filters are designed in the per-unit system to satisfy the requirements on the injected grid current and at the same time minimize the overall filter size through minimizing the total energy stored in the filter components. The experimental results of a downscaled laboratory prototype with a low switching frequency prove the effectiveness of the proposed design procedure. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase single-stage isolated zero current switched (ZCS) current-fed full-bridge ac/dc converter is proposed for IGBT-based high-power power factor correction (PFC) applications. By adding an additional commutation path and few resonant components, ZCS operation is realized for all IGBTs. The conduction loss is also lowered by the additional path. Furthermore, the control strategy for the proposed converter is compatible with that developed for traditional PFC converter. In this paper, the topology derivation and circuit operational analysis are given. The control strategy is introduced. A 3-kw prototype is developed and tested to verify the circuit functionality. Finally, the efficiency performance is investigated and comparison is made to show the advantages of the topology. [ABSTRACT FROM PUBLISHER]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

This paper presents a new five-level T-type nested neutral point clamped (T-NNPC) converter. The proposed five-level T-NNPC topology is very attractive for medium-voltage applications as it can work in a wide range of voltages without the need of devices in series, and fewer components compared to the other five-level topologies. A model predictive control (MPC) strategy is also developed for the proposed converter to control the output currents at different output frequencies, and control flying capacitor voltages. A discrete-time model of the converter is developed and the control objectives that are the output currents and flying capacitor voltages are defined regarding switching states. A cost function is defined to minimize the deviation of the predicted values of the control objectives from their desired values. During each sampling time, the best switching state is selected and applied to the converter. The performance of the proposed five-level T-NNPC and the developed MPC strategy is studied in the MATLAB/Simulink environment, and the feasibility of the converter is evaluated experimentally. [ABSTRACT FROM AUTHOR]

When providing ac output, modular multilevel converters (MMCs) experience power fluctuation in the phase arms. The power fluctuation causes voltage ripple on the module capacitors, which grows with the output power and inversely to the output frequency. Thus, low-frequency operations of MMCs, e.g., for motor drives, require injecting common-mode voltages and circulating currents, and strict dc voltage output relative to ground is impossible. To address this problem, this paper introduces a novel module topology that allows parallel module connectivity in addition to the series and bypass states. The parallel state directly transfers power across the modules and arms to cancel the power fluctuations and hence suppresses the capacitor voltage ripple. The proposed series/parallel converter can operate at a wide frequency range down to dc without common-mode voltages or circulating currents; it also allows sensorless operation and full utilization of the components at higher output frequencies. We present detailed simulation and experiment results to characterize the advantages and limitations of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel noncoupled inductor high voltage gain single-ended primary-inductor converter (SEPIC) is presented. The proposed converter has various advantages, such as lower voltage stress on the switches, noninverting output voltage, high efficiency, and high voltage gain. Also, the introduced converter has a continuous input current which makes it suitable for renewable energy and fuel cell applications. Moreover, high voltage gain is achieved without using any transformer and coupled inductor, thus there is not any voltage overshoot for the switches during the turn-off process. This effect allows low conduction losses by using lower voltage rating switches and also additional clamping circuit is not needed. The control system of the presented converter is simple and the converter can be easily controlled in continuous conduction mode mode operation. Because, the gating pulses for both of the switches are the same and wide output voltage range is achieved only by changing the duty cycle. Furthermore, the number of the components compared to the other noncoupled inductor, SEPIC-based converters which provide near voltage gain to the proposed converter, is reduced. The detailed operation of the introduced converter and design considerations are discussed. Experimental results are presented to verify the performance of the proposed dc–dc converter. [ABSTRACT FROM AUTHOR]

This paper presents an approach for dealing with the control of five-level, diode-clamped rectifiers. The control of such converters is challenging, as voltage balancing among capacitors is not a trivial task. Some of the existing approaches that cope with this problem use specific modifications of one of the traditional modulation techniques, such as using redundant vectors in space vector modulation (SVM). The main feature of the proposed technique is that part of the modulation is considered in the system equations and, in this way, the voltage balance can be solved designing a specific controller for this problem. As a result, several levels are used within a switching period. Furthermore, it is shown that the proposed approach hardly affects the control of active and reactive powers and total dc-link voltage in such a way that the well-known direct power control can be applied. As a consequence, the resultant modulation stage is simpler than other techniques based on, e.g., SVM. The effectiveness and good performance of the system under the proposed control approach are validated by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

Cascaded H-bridge (CHB) is a promising topology for medium-voltage high-power applications. CHB consists of low-power H-bridge modules in each phase, and these modules are connected in a cascade manner to achieve multilevel operation. However, CHB requires a phase-shifting transformer with multiple secondary windings to generate an isolated dc source for each module, and this requirement increases the overall system cost. In this paper, a series connection of low-power modules is employed to realize a new power converter called a series-connected multilevel converter. Each phase of the proposed topology requires a single isolated dc source. Hence, the required number of secondary windings is considerably reduced. This approach also minimizes the complexity and cost of the overall system. The operation of the proposed topology is presented by using three-level neutral point clamped modules in each phase. Model predictive control (MPC) is employed to control the dc-bus capacitor voltage and output currents of the proposed topology. A discrete-time mathematical model of the proposed topology is also developed to predict the future behavior of control variables. The performance of the proposed topology with MPC is verified through MATLAB simulations and a scaled-down laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, a fully soft-switched bidirectional dc–dc converter is proposed. All semiconductor devices are soft switched, while its control circuit remains pulsewidth modulated. This condition is achieved only by one auxiliary switch. So, the proposed topology has less complexity in comparison with other similar structures. The energy conversion through the proposed topology during buck and boost modes is highly efficient due to achieved soft-switching condition. The auxiliary circuit operates once during each switching cycle. The converter is analyzed and a 250-W laboratory prototype of the proposed converter is constructed. The experimental results are presented that confirm the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

The hybrid modular multilevel converter with cascaded full bridges (HMMC-CFB) is a recently proposed dc fault tolerant converter topology for high-power applications. It has a director part (DP) consisting of a series of connected half-bridge submodules, and a wave-shaping part (WSP) composed of a series of connected full-bridge submodules (FBSMs). The submodules in DP avoid high voltage stresses and improve synchronization between DP and WSP by slowing down the change rate of DP output voltage. This slowdown is achieved by using a trapezoidal reference signal for DP. The WSP attenuates the voltage harmonics produced by DP. However, the energy exchanged by WSP changes with modulation index, which may cause improper voltage regulation of the submodule capacitors. This paper proposes a new control technique to regulate the energy exchanged by WSP, which uses a variable slope trapezoidal reference signal of DP. To obtain this slope, the feedforward and feedback controllers are used. The feedforward controller gives the value of slope depending on the modulation index (mv) to keep the energy exchanged by WSP nearly equal to zero, whereas the losses and nonideality of the converter are taken care of by the feedback controller. This technique guarantees proper voltage regulation of the submodule capacitors for all modulation indices. The efficacy of the proposed technique is confirmed using simulations and experimentations. This paper also presents a circulating current suppressing controller for HMMC-CFB. The proposed control schemes and dc fault tolerant capability of HMMC-CFB are tested on a grid-connected model built in PSCAD. [ABSTRACT FROM AUTHOR]

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

In high-voltage applications, the magnitude of total semiconductor losses (on-state and switching) determines the viability of modular-type multilevel converters. Therefore, this paper presents a new cell arrangement that aims to lower total semiconductor loss of the modular multilevel converter (MMC) to less than that of the half-bridge modular multilevel converter (HB-MMC). Additional attributes of the proposed cell are: it eliminates the protective thyristors used in conventional half-bridge cells that deviate part of the dc-fault current away from the antiparallel diode of the main switch when the converter is blocked during a dc short-circuit fault, and it can facilitate continued operation of the MMC during cell failures without the need for a mechanical bypass switch. Thus, the MMC that uses the proposed cell retains all advantages of the HB-MMC such as full modularity of the power circuit and internal fault management. The claimed attributes of the proposed cell are verified using illustrative simulations and reduced scale experimentations. Additionally, this paper provides brief and critical discussions that highlight the attributes and limitations of popular MMC control methods and different MMC cells structures proposed in the literature, considering the power electronic system perspective. [ABSTRACT FROM AUTHOR]

This paper presents the analysis and design of an isolated high-voltage LLC resonant dc–dc full-bridge converter based on symmetrical quadrupler rectifier (SQR). Unlike conventional Cockcroft–Walton and full-bridge diode rectifiers, the SQR circuit provides significant improvement in power density by reducing the transformer turns-ratio without much increase in the output impedance. Moreover, the LLC converter can provide additional voltage boost, if operated, below the series resonant frequency of the LLC tank. The operating region of the converter is chosen in such a way that the converter always operates in ZVS for all line and load conditions with additional voltage boost. A new method based on basic differential equation is proposed for the accurate analysis and design of the converter and subsequently, the key results are compared with a first harmonic approximation based analysis method. A 120 V dc input, 2 kV output, 200 W laboratory prototype has been designed, built, and tested. Simulation and experimental results shown in this paper demonstrate the validity of the analysis and design of the presented converter. [ABSTRACT FROM AUTHOR]

A new active-clamped zero-voltage switching (ZVS) push–pull converter is proposed in this paper. Compared with the conventional push–pull converter, one auxiliary switch $Q_{{3}} and a clamping capacitor Ca are added in the primary side of the transformer to recycle the energy stored in the leakage inductors and clamp the voltage spike. Owing to the proposed converter which maintains ZVS of all the three switches from full load to very light-load condition, switching losses are reduced significantly. The voltage across the switch can be clamped at the input voltage plus the clamping capacitor voltage, i.e., V\rm{in}{+}VCa, are much less than those of a conventional push–pull converter that enabling the use of low-voltage, low-performance, and low-cost devices. In addition, the proposed topology can eliminate the problems of flux imbalance existing in the conventional one. Detailed operation, analysis, design, comparative study, and experimental results for the proposed converter are presented in this paper. An 800 W prototype was developed in the laboratory to evaluate and demonstrate the validity of the converter. [ABSTRACT FROM AUTHOR]

This paper proposes a multilevel series compensator (MSC) to deal with voltage sags/swells, harmonic compensation, or reactive power compensation. Such a device can be considered as a dynamic voltage restorer or a series active power filter (Series-APF). The MSC can improve the power quality of loads located in stiff systems. The configuration is based on three-phase bridge (TPB) converters connected by means of cascaded single-phase transformers. This arrangement permits the use of a single dc-link. A generalization for $K$ -stages in which $K$ -transformers are coupled with $K$-TPB converters is presented. The topology permits generating a high number of levels in the voltage waveforms with a low number of power switches in comparison with a classic topology. The multilevel waveforms are generated by the converters through a suitable pulsewidth modulation (PWM) strategy that takes into consideration the transformer turns ratios. Modularity and simple maintenance make the proposed MSC an attractive solution compared with some conventional configurations. Model, PWM strategy, and overall control are discussed in this paper. Simulation and experimental results are presented as well. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel single-switch dc/dc converter for the future renewable electric energy delivery and management system to implement the distributed renewable energy resources (DRER). The DRER is responsible for the maximum power point tracking of the photovoltaic panel (PV) module and also for the control of central energy storage device. Due to the characteristics of the PV module and the dc-bus, the single power stage must provide low current ripple in the input and output terminals, must operate with output current and voltage regulation, and present a high-voltage conversion ratio. To achieve such features, this paper proposes a novel integrated Boost–Zeta converter. To avoid a complex modeling and control, we propose a disaggregation concept for this. Experimental results are presented for the purpose of operating the converter and also for the operation of the system. [ABSTRACT FROM PUBLISHER]

Various magnetically coupled impedance source (MCIS) networks have been proposed in the literature for increasing voltage gain and modulation index simultaneously while reducing the number of passive components used in the converter. However, applications of such networks have been limited by their discontinuous currents drawn from the sources and/or high stresses experienced by their components. This paper thus proposes three new MCIS networks named, respectively, as quasi-Y-source, quasi-Γ-Z-source, and quasi-T-source or quasi-trans-Z-source networks. These new networks inherit all advantages of the existing MCIS networks. In addition, they demonstrate advantages like continuous input currents, reduced source stresses, and lower component ratings that are not achievable by other existing networks. Further, dc-current-blocking capacitors used in the networks help to avoid saturation of magnetic core. Derivations of all two-winding MCIS networks, including existing and new networks, from the generalized three-winding MCIS networks are then systematically illustrated, before comparing them. Operational principles, mathematical derivations, simulation, and experimental results of all studied networks have been presented in the paper. [ABSTRACT FROM PUBLISHER]

Modular multilevel converters (MMCs) are being developed for the grid connection of offshore wind or tidal farms. In order to reduce the construction and maintenance costs, it is desirable to reduce the weight and volume of the system. In current MMC submodule designs, the reservoir capacitor usually accounts for over 50% of the total volume and 80% of weight. This paper presents a new design concept and control principle for a submodule using the stacked switched capacitor (SSC) architecture that can significantly reduce the capacitor size in an MMC. Practical considerations for a high-voltage high-power SSC-based MMC submodule are presented in this paper, through the design of a 21-level, 40-kV (pole-pole dc), 19.1-MW, grid-connected system, and the concept is demonstrated experimenttally on a scaled-down 400-V, 12.3-Apeak laboratory prototype submodule. It is shown that with the proposed SSC architecture, the total volume of capacitors in each submodule can be reduced by more than 40% without significantly increasing the power loss. [ABSTRACT FROM AUTHOR]

This paper presents a three-phase open-end winding induction motor drive. The drive consists of a three-phase induction machine with open stator phase windings and dual-bridge inverter supplied from a single dc voltage source. To achieve multilevel output voltage waveforms, a floating capacitor bank is used for the second of the dual bridges. The capacitor voltage is regulated using redundant switching states at half of the main dc-link voltage. This particular voltage ratio (2:1) is used to create a multilevel output voltage waveform with three levels. A modified modulation scheme is used to improve the waveform quality of this dual inverter. This paper also compares the losses in the dual-inverter system in contrast with a single-sided three-level neutral point clamped converter. Finally, detailed simulation and experimental results are presented for the motor drive operating as an open-loop v /f controlled motor drive and as a closed-loop field-oriented motor controller. [ABSTRACT FROM PUBLISHER]

Pulse-width-modulated (PWM) converters have been widely applied for power processing, and they are typically the stems of other types of converters, such as quasi-resonant, Z-source, and switched-inductor hybrid converters. Development of PWM converters has been spanning over a century, starting from the buck converter. The well-known PWM converters include buck, boost, buck–boost, Ćuk, single ended primary inductive converter (SEPIC), zeta, Z-source, quasi-Z source, etc. Many attempts have been proposed to develop these converters based mostly on canonical cell concepts and by introducing extra LC filters to the cells. This paper presents an enhancement to the layer and graft schemes by introducing the ideas of dc voltage/current offsetting, capacitor/inductor component splitting, diode grafting, and inverse operation of PWM converters. The PWM converters, which can be operated in continuous conduction mode (CCM) or discontinuous conduction mode (DCM), therefore can be synthesized systematically according to decoded transfer gains. Decoding and synthesizing PWM converters uniquely bridge transfer gains to converter topologies and provide readers a comprehensive understanding of PWM-converter evolution from the original converter, the buck converter. Additionally, in this paper, the Ćuk, SEPIC, and zeta converters all with the same transfer gain of $D/(1 - D)$ are proved to be equivalent to the buck–boost converter with an extra LC filter. For further illustrating the proposed approaches, various types of Z-source converters, switched-capacitor/switched-inductor hybrid converters, and a single-stage interleaved converter are reviewed, and new PWM converters are developed. [ABSTRACT FROM AUTHOR]

In this paper, a high step up converter consisting of an integrated quadratic-boost converter and a voltage doubler is proposed. The integration of the quadratic-boost converter makes the system easier to lift up its voltage gain through slightly increasing the duty ratio of the single switch. The voltage doubler further increases the voltage gain of the system as the turn ratio rises. The voltage stresses on the switch and the diodes are decreased for such cascaded topology. Different operation modes are analyzed and mathematical analysis of the converter is presented in detail. The leakage inductance contributes to realizing zero current switching of the diodes in the second boost stage and the doubler and the energy can be recycled to the load. A 38-W prototype is built to work as a vehicle LED driver. Experiments are conducted to verify the advantages of the proposed converter and the efficiency is 90% at the nominal operating point. [ABSTRACT FROM AUTHOR]

In a power electronics system, an electrolytic capacitor (E-Cap) is widely used, whose performance degradation can be reflected by the change of capacitance (C) and equivalent series resistance (ESR). This paper proposes a new online C and ESR monitoring scheme for the output electrolytic capacitor in a discontinuous conduction mode (DCM) flyback converter. The mathematical relationship between the instantaneous capacitor voltage and other parameters is analyzed and then the scheme of undetermined coefficients based on the multiple-spot sampling and least square method is further proposed. In addition, considering the particularity of high ripple current and the resultant voltage ripple variation range, especially with the temperature, an inverse ripple voltage isolation amplifier with variable amplification factor and negative voltage elimination is put forward so as to make digital signal processor identify the temperature change easily. The proposed scheme is noninvasive as only voltage signals need to be sampled and no current sensor is necessary. A prototype is built and the experiments are made to verify the effectiveness of the proposed method, from which the data are in accordance with the results measured by an LCR meter. [ABSTRACT FROM AUTHOR]

In recent years, modular multilevel converter (MMC) is considered for medium-voltage variable speed drives (VSD) due to its modularity and higher reliability. However, the major drawback of the MMC-based VSD is the higher capacitor ripple voltage at lower operating speeds. In literature, this ripple voltage is reduced by injecting a high-frequency circulating current into each arm. This additional circulating current increases the overall current rating of the devices, inductors, and capacitors. Alternatively, the capacitor ripple voltage can be reduced at the lower output frequency by reducing the dc-bus voltage. This paper proposes a new configuration using a multipulse diode-bridge rectifier to reduce the dc-bus voltage when the drive is operated at lower speeds. Therefore, the capacitor ripple voltage decreases without injecting any circulating current. In addition, a new technique is proposed to maintain the peak-to-peak value of the submodule capacitor ripple voltage constant at near-zero speed. The proposed converter with 24-pulse rectifier configuration is simulated in MATLAB/Simulink, and the experimental validation is carried out on a prototype with 12-pulse rectifier. [ABSTRACT FROM AUTHOR]

In this paper, a new modified single-switch single-ended primary inductor converter (MS2-SEPIC)-based high step-up dc–dc converter is presented. The proposed topology uses the coupled-inductor (CL) technique and a voltage tripler rectifier, which results in a high voltage gain for the converter. Here, the switching loss has been reduced significantly owing to the quasi-resonance operation of the circuit created by the leakage inductance of the CL along with circuit capacitors. The operational principles and steady-state analysis are discussed. Experimental results based on a 100 W laboratory prototype verify the validity of theoretical analysis. [ABSTRACT FROM AUTHOR]

A 1-MHz-modified single-ended primary-inductor converter (SEPIC) circuit is presented in this paper as an LED driver for automotive headlights. On the basis of traditional SEPIC, only a diode and two capacitors are added; therefore, the circuit structure is relatively simple and the volume is relatively small. High step-up capability is obtained with moderate duty cycle. Compared with traditional step-up circuit such as boost, low-voltage stress is gained which is beneficial to device selection. Zero-voltage switching is achieved at the same time to reduce switching loss. Planar inductors are used with the advantages of low profile and good thermal characteristic. Operational principle and parameters design process are introduced in detail. A 36-W prototype has been designed to demonstrate theoretical analysis. Obtained efficiency was up to 90.91% at full load. [ABSTRACT FROM AUTHOR]

Switched-capacitor converter (SCC) featuring high efficiency and power density has attracted industry interest, but weak output voltage regulation hinders its application. This paper presents an optimized phase-shift (PS) control strategy for a bridge modular SCC, utilized in energy storage system, to obtain continuous conversion ratio and high-efficiency operation. By employing a small inductor as current buffer, the control strategy could be implemented to regulate output voltage conveniently with excellent steady and dynamic performance in step-down mode as well as step-up mode. Most importantly, the high-efficiency operation mechanism never reported before is revealed here. Correspondingly, the active circumfluence could be controlled through optimizing the range of PS time, which will avoid the loss in circuit self. Meanwhile, the soft-switching conditions of all the switches are comprehensively analyzed and soft-switching operations are achieved according to the logic timing control of the power devices, improving efficiency further. Finally, the prototype of the proposed converter was built and the experimental results validated the principle and features of the conversion method. [ABSTRACT FROM AUTHOR]

This paper presents a modular multilevel series/parallel converter (MMSPC) with intermodule switched-inductor power transfer. The switched-inductor voltage conversion feature allows controllable and efficient transfer of energy between modules with nonnegligible voltage difference, providing both step-down and step-up functionalities. Thus, this converter can accurately control and rapidly adjust the voltage of each module to generate an ac output voltage waveform with a controllable number of levels, increasing the quality of the output. Moreover, the intrinsic dc–dc conversion feature can generate a dc controllable output voltage and enable new applications. In this text, we specifically demonstrate how the flexibility of obtaining both ac and dc output with the same setup renders the topology promising for battery energy storage systems and dc microgrid applications. Experimental results validate the topology and concept of an MMSPC with intrinsic switched-inductor conversion. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is attractive for medium- or high-power applications because of the advantages of its high modularity, availability, and high power quality. Reliability is one of the most important challenges for the MMC consisting of a large number of submodules (SMs). The capacitor monitoring is one of the important issues in the MMC. This paper proposed a reference submodule (RSM)-based capacitor monitoring strategy for the capacitance estimation in the MMC, where the capacitances in the monitoring SMs can be estimated based on the capacitor voltage relationship between the RSM and the monitoring SMs. The proposed monitoring strategy does not rely on the information of all capacitor voltage and current, which effectively simplifies the algorithm for capacitance estimation. The simulation studies with the time-domain professional tool PSCAD/EMTDC are conducted and a down-scale MMC prototype is also tested in the laboratory with the proposed capacitor monitoring strategy. The study results confirm the effectiveness of the proposed capacitor monitoring strategy. [ABSTRACT FROM AUTHOR]

In this paper, a novel buck–boost converter with low electric stress on components and negative output voltage is proposed. The operational principle, steady-state analysis, and small-signal modeling of the proposed buck–boost converter in continuous conduction mode are presented. Comparisons among another five buck–boost converters and the proposed buck–boost converter are presented. It is found that the proposed converter's voltage gain is smaller than the other converters’ in step-down mode. Also, based upon the comparisons among the same kind and same number of components, the voltage and current stresses on the power switch of the proposed buck–boost converter are less than or equal to those of the comparative converters, and the voltage stress on the charge pump capacitor and the switching device power rating of the proposed buck–boost converter are always lower than those of other comparative converters. The efficiency of the proposed buck–boost converter is highest among those converters having the same number of elements. These advantages make component selection for the proposed converter much easier, and it can be used directly in applications needing a negative voltage source. Finally, simulation results and circuit experiments are given for validating the effectiveness of the proposed buck–boost converter. [ABSTRACT FROM AUTHOR]

High-brightness light-emitting diode (LED) is next generation of green lighting. However, the bulky electrolytic capacitor is required to compensate the difference of pulsating power, thereby restricting the lifetime. Meanwhile, the existing drivers based on pulse frequency modulation (PFM) is bound to arouse heavy electromagnetic interference. In this paper, the series resonant converter based LED drive is proposed to overcome the shortcomings of electrolytic capacitor and PFM control. The proposed method is to attenuate the low frequency ripples delivered from the power factor correction (PFC) to LEDs; therefore, the capacitance is reduced for energy storage of offline LED drivers. On account of the adoption of the switching controlled capacitor (SCC), the constant frequency control is achieved by the regulations of the equivalent capacitance. Half-bridge switches are shared by the bridgeless PFC and the resonant unit, therefore, single-stage LED drive is realized with high efficiency. In addition, SCC is simultaneously shared for the upper and lower half-bridge to reduce the cost and improve the power density. Operating principle, design considerations, and performance comparisons are examined in detail. Finally, all the superior performances of proposed LED driver are verified by simulation and experimental prototypes with two-channel LEDs, and rated output power of 80 W. [ABSTRACT FROM AUTHOR]

A simple buck–boost LED driver suitable for battery operated applications with limited input voltage level is presented in this paper. Soft switching performance is provided for the main switch via a resonant circuit to improve the converter efficiency. The incorporated auxiliary switch also performs under zero voltage switching condition. Both power switches can be driven with a simple gate drive circuit, so, the additional switch does not add any driving complexity. In addition, only one magnetic element is utilized in the proposed LED driver which contributes to circuit simplicity and lower weight and size. Also, all diodes turn off at zero current switching which eliminates the reverse recovery losses and improves efficiency. A laboratory prototype converting 12 V input voltage to 32 V output operating at 26 W output power is implemented and tested to verify the effectiveness of the proposed LED driver. [ABSTRACT FROM AUTHOR]

In this paper, a novel modular full-bridge converter is proposed for three-phase switched reluctance motors (SRMs), which provides an advanced fault-tolerance solution for both the open- and short-circuit faults in switching devices. The proposed converter is composed of two standard six-pack switch modules, providing great benefits for industrial massive production due to the modular topology. Under normal conditions, bidirectional current excitation is developed in the proposed converter, where all the switching devices are actively involved, which makes full use of the switches and averages the heat dissipation for the heat sink design. When a switch fault occurs, the fault signature can be extracted by detecting the characteristics of phase currents and operation modes, and effective fault-tolerance strategies are further applied to achieve the fault-tolerance operation accordingly. Under switch open-circuit faults, the faulty phase is adjusted to unidirectional current excitation without degrading the motor performance. Under switch short-circuit faults, the motor can still work steadily with a single six-switch inverter module by easily reconstructing the proposed converter, without losing any phase windings. The simulation and experiments on a three-phase 12/8 SRM are carried out to validate the feasibility of the proposed converter and control techniques. [ABSTRACT FROM AUTHOR]