Search

A new low-power single-stage ac-dc converter is proposed in the paper. The outstanding feature of the converter is that it can operate with a sinusoidal input current and a low primary-side dc bus voltage that is much less variable than that found in other single-stage converters. The operation of the converter is discussed in the paper and its various modes of operation are explained in detail. An analysis of the converter's steady-state characteristics is performed and the results are used in the design of the converter. Experimental results obtained from a prototype converter are also presented. [ABSTRACT FROM AUTHOR]

In this paper, a built-in voltage gain extension cell is proposed to give a universal topology derivation on next-generation high step-up converters for large voltage gain conversion systems. Several improved single-switch high step-up converters with built-in transformer voltage multiplier cell are derived with some advantageous performance, which includes extremely large voltage conversion ratio, minimized power device voltage stress, effective diode reverse-recovery alleviation, and soft-switching operation. The turns ratio of the built-in transformer can be employed as another design freedom to extend the voltage gain, which shows great design flexibility. Compared with their active clamp counterpart, only one MOSFET is required to simplify the circuit configuration and improve the system reliability. The over resonance frequency and the below resonance frequency operation modes are studied to explore the circuit performance, and the key parameter design criterion is provided to show a valuable guidance for future industrial applications. Finally, the experimental results from a 500 W 36-380 V prototype are provided to validate the effectiveness of the main contributions in this paper. [ABSTRACT FROM AUTHOR]

Cascaded converters are adopted in many power systems to manage sources and loads at different voltage levels simultaneously. DC bus capacitor is one of the key components in these converters due to its energy storage and fast response capabilities. However, the ripple current through the capacitor will influence its lifetime and the overall efficiency of the converter. Previous studies showed that the capacitor current of ac systems is optimized when the duty cycles are synchronized under in phase or antiphase condition. In this paper, the bus capacitor ripple current of cascaded two-stage converters for dc systems with different combinations of duty cycles is analyzed. It is found that the optimum capacitor current ripple varies depending on the values of individual duty cycles and the phase-shift angle between them. By properly adjusting the phase shift, the capacitor RMS current value can be reduced without affecting the converter normal operation or the need for extra sensing circuits, hence improving the energy conversion efficiency and prolonging the capacitor lifetime with relatively simple implementation. To illustrate, a case study of a two-stage dc/dc converter is carried out. A laboratory prototype converter confirmed a maximum efficiency improvement of 2.8% if the phase shift is adjusted properly when compared to the same converter with the worst case phase-shift angle. [ABSTRACT FROM AUTHOR]

This paper presents a multilevel step-up dc/dc converter for dc-grid-based offshore wind energy conversion applications. The main features of the proposed multilevel converter are as follows: 1) the voltage stress of the power devices can be reduced, making it suitable for high-voltage applications; 2) the boost inductor can be reduced significantly, leading to the outstanding dynamic performance; and 3) high-voltage gain can be obtained and thus is well-suited for high-gain applications. Theoretical analysis was carried out for a four-level step-up converter, based on which, the converter can be extended to any arbitrary number of levels. The proposed four-level converter was verified by a simulation and evaluated by comparing with a conventional multilevel dc/dc converter in terms of the component stress and power device count. The developed topology was implemented on a 2-kW prototype converter to evaluate its feasibility. [ABSTRACT FROM AUTHOR]

The use of modular multilevel converters (MMC) in high-voltage direct current (HVdc) transmission systems has grown significantly in the past decade. The efficiency, cell capacitor voltage ripple, and dynamic performance are three contradictory aspects of the MMC which are related to the converter switching scheme. Previously introduced tolerance band (TB)-based schemes enable efficient and simple control for grid-connected MMCs. This paper addresses the dynamic operation of TB switching schemes by proposing a dynamic boundary setting technique for steady-state operation and a switching scheme scheduling controller for transient fault handling. The performance of proposed methods are validated in a realistic point-to-point HVdc link, modeled in real-time digital simulator where two converters with 512 cells per arm are implemented. Utilizing the proposed methods will enable efficient implementation of TB-based schemes for different operating points, and also a robust transient fault handling. [ABSTRACT FROM AUTHOR]

Linear small-signal models of a dc–dc converter often ignore switching dynamics; thus such models are insufficient to fully explore the performance objective under large signal transients. Linear/nonlinear hybrid controllers are promising alternatives; however, they require structurally different hardware resources along with extra antiwindup arrangements. This paper proposes a geometric tuning method in a digitally current-mode-controlled buck converter under continuous-conduction mode. This considers a proportional-integral voltage controller along with a load current feedforward in the digital domain, while the inductor current has a traditional analog implementation. This resembles a first-order switching surface with near load-invariant regulation; thus a (fixed) small integral gain is sufficient to minimize the steady-state error. Using phase-plane geometry, the objective is to tune the controller gain in a way to achieve proximate time optimal recovery using a fixed-frequency pulse-width modulator and also to retain the large-signal stability. The effects of parameter variation and finite sampling are analyzed. The proposed tuning is implemented using an FPGA device. [ABSTRACT FROM AUTHOR]

In this paper, a single-phase converter consisting of two legs with four switches, called the $\theta$-converter, is proposed. It has a common ac and dc ground, which reduces common mode currents and removes the need for an isolation transformer, and two capacitors: one across the whole dc bus and the other across the output. The dc bus capacitor provides a direct path for the double-frequency ripple current inherently existing in single-phase converters to return continuously so the output capacitor can be sized very small, only to filter out switching ripples. Moreover, the dc bus capacitor is intentionally designed to store the system ripple energy with large voltage ripples, which reduces its capacitance. Hence, the total capacitance needed and the output voltage ripples are reduced at the same time. This makes it cost-effective to use highly reliable film capacitors instead of bulky and vulnerable electrolytic capacitors. Because of the removed isolation transformers and bulky electrolytic capacitors, the power density and system reliability are improved. In order to properly operate the converter, two independent controllers are designed for the two legs, respectively, to achieve the desired functions and other normal objectives, such as the unity power factor. Experimental results are presented to demonstrate the high performance of the proposed converter. [ABSTRACT FROM AUTHOR]

Differential-mode buck-boost inverters have merits such as reduced switch number, ability to provide voltages higher or lower than the input voltage magnitude, improved efficiency, reduced cost and size, and increased power density, especially in low-power applications. There are five buck-boost inverters that can provide flexible output voltage without the need of a large electrolytic input side capacitor, which degrades the reliability of inverters. The continuous input current of these inverters is appropriate for maximum power point tracking operation in photovoltaic and fuel cells applications. Three of the five inverters can be isolated with high-frequency-link transformers where the common-mode leakage current can be mitigated. However, the performance and control of such converters have not been discussed in detail. In this paper, the five possible single-stage three-phase differential-mode buck-boost inverters with continuous input current are investigated and compared in terms of total losses, maximum ripple current, total harmonic distortion, and device and passive element ratings. In addition, the possible methods are presented for eliminating the input third-order harmonic current, resulting from the stored energy in the passive elements, as well as the output second-order harmonic currents. The ability for isolating the input and output sides of the inverters with a small–high frequency transformers is discussed. A changeable-terminal 2.5-kW bidirectional inverter is used to validate the design flexibility of the inverter topologies, when digital signal processor-controlled. [ABSTRACT FROM AUTHOR]

This paper presents a power electronics converter to generate bipolar high-voltage pulses using low-voltage dc source. Converter is designed based on charging of different capacitors by a predetermined switching pattern and their discharging on the load for pulsed power applications. Low number of power electronics devices and bulky transformer elimination are main advantages of the proposed converter. According to new findings, bipolar high-voltage pulses may lead to higher efficiency in many applications, such as food sterilization industry. The proposed pulse generator generates bipolar controllable pulses with a modular circuit structure based on a capacitor-switched network. Experimental results are presented to verify the analysis. [ABSTRACT FROM AUTHOR]

In this paper, the switching cell concept is extended to isolated ac–ac converters, and a highly reliable double step-down ac–ac converter is proposed with high-frequency transformer (HFT) isolation. By using the switching cell structure and coupled inductors, the proposed converter has no commutation problem as it is immune from both short-circuit and open-circuit problems, even when all the switches are turned on or turned off, simultaneously. Therefore, it does not require pulse width modulation dead times along with bulky and lossy RC snubbers or voltage-sensing circuitry to implement soft-commutation strategies, resulting in high reliability and high quality output waveforms. The HFT in the proposed converter provides electrical isolation and safety which is required in applications such as dynamic voltage restorer (DVR), solid-state transformer (SST), etc., without the need for external bulky line frequency transformer. Moreover, all the passive components experience twice the switching frequency; therefore, their size can be reduced. The proposed converter is very suitable for application as DVR, to compensate both voltage sags and swells, owing to its ability to provide both inverting and noninverting outputs. A detailed theoretical analysis and operation of the proposed ac–ac converter are provided, and its applications as DVR and SST are also discussed. Experimental results with scaled-down prototype are also provided to verify its performance. [ABSTRACT FROM AUTHOR]

In this paper, a novel high step-up dc–dc converter with a multicoupled inductor (MCI) and voltage multiplier is proposed for a sustainable energy system. The combinatorial employment of these components significantly extends the voltage boostability and reduces the voltage stress of the main switches. The special structure of branch cross coupling makes the two branches of current autobalance. Meanwhile, the utilization of MCIs makes the most of the magnetic core to further improve the power density. The diode reverse-recovery problem is alleviated because its current falling rate is controlled by the leakage inductance of the MCI. Moreover, the voltage spike of the main switches at their turn-off is clamped by a clamp capacitor. The interleaved operation results in the cancelation of the input current and output voltage. Next, the operating principle and performance of the converter are discussed in detail. Finally, a prototype circuit with 1-kW output power is implemented to verify the performance of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents an analytical and experimental comparison of a two-phase buck converter and a two-phase, series capacitor buck converter. The limitations of a conventional buck converter in high-current (10 A or more), and high-frequency (HF, 3–30 MHz) point-of-load voltage regulators with large voltage conversion ratios (10-to-1) are highlighted. The series capacitor buck converter exhibits desirable characteristics at HF, including lower switching loss, less inductor current ripple, automatic phase current balancing, duty ratio extension, and soft charging of the energy transfer capacitor. Analysis of the topologies indicates that switching loss and inductor core loss can dominate at HF. Results from side-by-side 12 V input, 1.2 V output hardware prototypes demonstrate that the series capacitor buck converter has up to 12 percentage points higher efficiency at 3 MHz and reduces power loss by up to 33% at full load (10 A). Some guidelines for inductor selection are provided, and a switch stress comparison reveals that the maximum converter switch stress is reduced by 30%. [ABSTRACT FROM AUTHOR]

This paper presents a control scheme based on the predictive control theory and Petri nets (PNs) formalism to control a flying capacitor multilevel converter. The proposed scheme takes advantage of the benefits offered by the finite control set-model predictive control (FCS-MPC) methodology and the versatility of PNs to regulate the capacitor voltages and output current, simultaneously. The inclusion of PNs allows us to simplify the control scheme. A first PN is used to select, from a subset of switching states, the switching state that accomplishes both control objectives. This approach reduces the computational burden if compared with a typical predictive control scheme. Furthermore, a PN-based prediction scheme is used to predict the capacitor voltages. This prediction scheme uses only measurements of output voltage and current, which reduces the number of required sensors. This approach allows us to implement the internal capacitor voltages control independently if a multileg configuration is needed. The scheme is experimentally validated in a five-level flying capacitor multilevel converter. [ABSTRACT FROM PUBLISHER]

In this paper, a simple control method of the half-bridge (HB) LLC converter with one additional switch and capacitor in the primary side is proposed for wide-input-voltage applications with the hold-up time conditions. At nominal input, since the proposed method enables the HB LLC converter to operate with large transformer magnetizing inductance, it can reduce the conduction and switch turn-off losses in the primary side, which makes it highly efficient. On the other hand, during the hold-up time, since the proposed method increases the resonant capacitance by turning on one additional switch, the HB LLC converter can obtain high-voltage gain. To confirm the validity of the HB LLC converter with the proposed method, a 325–385 V input and 56 V/350 W output laboratory prototype is built and tested. [ABSTRACT FROM PUBLISHER]

Hybrid multilevel converters combine features of conventional multilevel topologies to provide an acceptable tradeoff between the advantages and disadvantages of these converters. For many industrial applications, common dc link is a requirement that limits the choice of topologies to neutral point clamped (NPC) and flying capacitor multicell (FCM) hybrid types. This paper investigates the operation of a hybrid five-level topology and proposes a modulation method that takes the advantage of the combined features of NPC and FCM. The dual flying capacitor (FC) active-neutral-point-clamped (DFC-ANPC) converter provides certain advantages such as natural soft switching of line frequency switches, elimination of the transient voltage balancing snubbers, and a more even loss distribution. Simulation results and experimental verification of the five-level DFC-ANPC converter are presented to validate the performance of the converter as well as the applied modulation technique. [ABSTRACT FROM AUTHOR]

In this paper, an improved model predictive control (MPC) of the modular multilevel converter (MMC) with reduced computational burden is proposed. A mathematical model of the MMC system based on the sum and difference of arm voltages are derived. Instead of determining the switching state of individual submodule (SM), the voltage levels of MMC are considered as control options based on the assumption that the SM capacitor voltages are well balanced. The further reduction of calculation effort is realized by using the tolerance band of capacitor voltages. The proposed MPC has a hierarchical structure. The cost function taking into account the ac-side current control, circulating current elimination and arm energy balancing is presented. The optimal voltage level, selected by the cost function, provides the voltage reference for the pulse width modulation modulator. The SM capacitor voltage balancing is done using a separate control loop. The proposed control strategy is investigated using an MMC high-voltage direct current system with 200 SMs in each arm in real-time simulation and hardware-in-the-loop tests. The performance of proposed method is verified by both steady-state and transient-state operations. [ABSTRACT FROM PUBLISHER]

This paper presents a new formulation of a finite control set model-predictive control (FCS-MPC) algorithm, allowing to determine the best commutation instant in order to optimize the converter current tracking. This algorithm, mixing properties of FCS-MPC method and time resolution related to pulse width modulation schemes, is illustrated in a parallel flying capacitor converter. The parallel association of classical commutation cells is a good solution for increasing the output current driven by the converters, while the standard semiconductor technology is used. The control strategy used with this type of connection must be able to ensure not only a good distribution of the output current among the different legs, but also the balancing of the floating capacitor voltages. [ABSTRACT FROM PUBLISHER]

This paper suggests a high-efficiency portable welding machine based on full-bridge converter with input-series-output-parallel (ISOP)-connected single transformer. Link voltage balance problem is theoretically analyzed according to deviations of transformer leakage inductances and transformer turns-ratios and simple voltage-balancing circuit using flying capacitor is introduced to remove this problem. Also, active-snubbing method is also proposed to improve overall efficiency by recovering parasitic resonant energy and regulating the voltage stress of rectifiers to the level that schottky diodes are available. The feasibility of the proposed structure has been verified with 17.5-kW welding machine with 60-kHz switching frequency. [ABSTRACT FROM PUBLISHER]

Phase-shifted carrier modulation is an industry standard in its application to multilevel H-bridge converters. The major advantage of this scheme over level-shifted and space vector modulation schemes is its inherent ability to evenly distribute losses between semiconductor devices. However, phase-shifted schemes suffer from harmonic degradation when operated at the low carrier frequencies required in high-power high-level number applications. This paper develops a model predictive modulation (MPM) scheme that achieves superior harmonic performance, compared to phase-shifted modulation, while ensuring equal semiconductor loss distribution. With respect to complete-enumeration-based predictive techniques, the proposed modulation significantly reduces the number of times the system cost function is evaluated. Reducing the number of calculations by several orders of magnitude ensures computational feasibility. Simulation and experimental results are presented, which confirm correct operation of the modulation strategy. [ABSTRACT FROM PUBLISHER]

Multilevel converters are mainly used in medium-voltage high-power applications. Active neutral-point-clamped (ANPC) flying capacitor multicell (FCM) converter is a well-known type of multilevel converters which is commercially available in high-power medium-voltage motor drive market. Since power loss investigation can be very advantageous in the design phase of multilevel converters, this paper presents an analytical approach to calculate and investigate the conduction and switching power loss in ANPC-FCM converter. First, the RMS and average currents of insulated-gate bipolar transistors (IGBTs) and antiparallel diodes are analytically calculated by considering the associated duty cycle of each IGBT and diode, converter modulation index, load current, and load power factor. Numerical results of the derived closed-form equations to calculate the RMS and average currents of IGBTs/diodes are compared with simulation results and experimental measurements. Numerical results match the simulation results and experimental measurements which validates the derived closed-form equations. Afterward, the obtained equations for RMS and average current computations are utilized to calculate the conduction power losses in a 12.1-MVA 6.6-kV nine-level (line-to-line) ANPC-FCM multilevel converter. For this purpose, a 4.5-kV 1.2-kA IGBT module from ABB is considered as a power switch and its parameters are employed in analytical computations and simulation of the ANPC-FCM multilevel converter for conduction power loss determination. Moreover, closed-form equations are derived for analytical determination of switching power losses for ANPC-FCM converter using Kapteyn (Fourier-Bessel) series. Based on the derived closed-form equations for conduction loss and switching loss calculation, a method is presented to determine the junction temperature in IGBTs and diodes for ANPC-FCM converter. [ABSTRACT FROM AUTHOR]

High-voltage-gain and wide-input-range dc–dc converters are widely used in various electronics and industrial products such as portable devices, telecommunication, automotive, and aerospace systems. The two-stage converter is a widely adopted architecture for such applications, and it is proven to have a higher efficiency as compared with that of the single-stage converter. This paper presents a modular-cell-based morphing switched-capacitor (SC) converter for application as a front-end converter of the two-stage converter. The conversion ratio of this converter is flexible and variable and can be freely extended by increasing more SC modules. The varying conversion ratio is achieved through the morphing of the converter's structure corresponding to the amplitude of the input voltage. This converter is light and compact, and is highly efficient over a very wide range of input voltage and load conditions. Experimental work on a 25-W, 6–30-V input, 3.5–8.5-V output prototype, is performed. For a single SC module, the efficiency over the entire input voltage range is higher than 98%. Applied into the two-stage converter, the overall efficiency achievable over the entire operating range is 80% including the driver's loss. [ABSTRACT FROM AUTHOR]

High-performance buck converters are often required in modern power electronic applications. An augmented buck converter (a main buck converter with augmentation circuits) can achieve fast transient recovery and small output voltage deviation. Compared with other augmentation circuits, a resonant augmentation circuit offers potential electromagnetic interference reduction due to the relatively low $di/dt$ value and compacts the circuit through a reduced inductance for resonance. In this paper, the performance analysis of an augmented buck converter constructed with the resonant circuit are described in detail in terms of voltage-deviation band and power loss. A circuit design and control principle is also proposed for achieving the required voltage deviation for a given transient-detection delay. A 12-to-5-V converter prototype is built to verify the analysis and effectiveness of the proposed methodology. It is demonstrated that the voltage deviation is reduced from 360 to 200 mV using the proposed resonant augmentation circuits and control scheme. The efficiency study shows that the power loss varies from 0.02 to 0.72 W, when the repetition frequency of 5-to-10-A transients changes from 100 to 5 kHz. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped (4L-HC) inverter is a newly proposed topology which is suitable for high-performance medium-voltage drives. Each phase of this topology consists of eight switches and a flying capacitor and the dc-link is split into three parts by two neutral points. In order to ensure the topology operating properly, the voltages across the flying capacitors and three dc-link capacitors should be controlled and maintain balanced at their nominal values. This paper presents a decoupled voltage balancing method for this 4L-HC inverter, including the voltage balancing of dc-link capacitors and flying capacitors. A modified phase-shifted pulse-width modulation method is used to regulate the voltages of flying capacitors and the central dc-link capacitor. The relationship between the neutral-point currents and the output voltage is studied and the upper and lower dc-link capacitor voltages are balanced by injecting an optimum zero-sequence voltage. Simulation and experimental results are presented to verify the validity of this method. [ABSTRACT FROM AUTHOR]

In this paper, the analysis and design of a three-level LLC series resonant converter (TL LLC SRC) for high- and wide-input-voltage applications is presented. The TL LLC SRC discussed in this paper consists of two half-bridge LLC SRCs in series, sharing a resonant inductor and a transformer. Its main advantages are that the voltage across each switch is clamped at half of the input voltage and that voltage balance is achieved. Thus, it is suitable for high-input-voltage applications. Moreover, due to its simple driving signals, the additional circulating current of the conventional TL LLC SRCs does not appear in the converter, and a simpler driving circuitry is allowed to be designed. With this converter, the operation principles, the gain of the LLC resonant tank, and the zero-voltage-switching condition under wide input voltage variation are analyzed. Both the current and voltage stresses over different design factors of the resonant tank are discussed as well. Based on the results of these analyses, a design example is provided and its validity is confirmed by an experiment involving a prototype converter with an input of 400-600 V and an output of 48 V/20 A. In addition, a family of TL LLC SRCs with double-resonant tanks for high-input-voltage applications is introduced. While this paper deals with a TL LLC SRC, the analysis results can be applied to other TL LLC SRCs for wide-input-voltage applications. [ABSTRACT FROM AUTHOR]

In this paper, a new three-level single-stage power-factor-corrected ac/dc converter is presented. The proposed circuit integrates the operation of a boost power factor correction converter and a three-level dc/dc converter into one converter. It does not have the problem of high component stress due to high rising intermediate bus voltages at light load conditions that other single-stage converters have because of its three-level structure. It can operate over a wider load range with significantly less output inductor current ripple; moreover, its input current has little distortion. In the paper, the operation of the new converter is explained in detail and analyzed, its steady-state characteristics are determined, and its design is discussed. Experimental results obtained from a prototype are presented to confirm the feasibility of the new converter. [ABSTRACT FROM AUTHOR]

This paper proposes a new circuit topology for SMES (superconducting magnetic energy storage), which is based on a pulse link concept of two converters. A two quadrant dc chopper and a dc/ac converter connected via high frequency dc pulse link voltage. This concept has two advantages. All semi-conductor switches operate under soft-switching condition, which results in low loss generation and possibility to increase switching frequency. The other advantage is eliminating smoothing capacitor between two conversion stages. By these advantages, the proposed converter has possibility to achieve high efficiency and power density with rich controllability. This paper describes operation principles of the proposed converter. First experimental verification of this concept was conducted with small scale setup. [ABSTRACT FROM PUBLISHER]

This paper presents a soft-switching boost converter with a flyback snubber for high power applications. The proposed converter configuration can achieve both near zero-voltage and zero-current soft-switching features, while it can reduce the current and voltage stresses of the main switch. In this paper, several passive and active snubbers associated with boost converters are first reviewed, and their limitations are then addressed. One of the boost converters with a flyback snubber is proposed and analyzed in detail to explain the discussed features. Experimental results obtained from a 5-kW boost converter have confirmed that the proposed converter configuration is attractive and feasible for high power applications. [ABSTRACT FROM AUTHOR]

In this paper, an integrated double buck–boost (IDBB) converter is proposed as a high-power-factor offline power supply for power-LED lamps. The IDBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains, providing high power factor and good efficiency. In this paper, the IDBB converter is analyzed, and a design methodology is proposed. It is demonstrated that, with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures can be made as high as that of the solid-state lamp. A design example for a 70-W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented. [ABSTRACT FROM AUTHOR]

The fault-tolerant multilevel converters are gaining increased interests for high-voltage direct current (HVDC) applications due to their ability to suppress the fault current during dc-side faults. However, most of these topologies use full-bridge submodules (FBSMs) resulting in the requirement of a large number of semiconductor switches. In this paper, a new generalized cross-connected SM (GX-SM) structure is presented, which requires lesser number of switching devices and provides the same functionality as the FBSM. A comparison of the switches required in the different converter topologies using FBSMs and GX-SMs is performed. The performance evaluation of two of the dc-side fault-tolerant converter topologies, namely alternate arm modular multilevel converter (AAMMC) and hybrid cascaded modular multilevel converter (HCMC) with the GX-SM, is performed using simulation studies done in PSCAD/EMTDC. The modulation and control schemes for these GX-SMs-based converters are presented. A new mixed-SM configuration of AAMMC is proposed which utilizes an optimal combination of GX-SMs and half-bridge SMs. The study results demonstrate the effectiveness of the proposed GX-SM structure, and satisfactory responses of the GX-SMs-based AAMMC and HCMC systems controlled using the presented modulation and control strategies under various system conditions. [ABSTRACT FROM PUBLISHER]

A simple and cost-effective precharge method for modular multilevel converter (MMC) by using a low-voltage direct current (dc) source is proposed in this paper. The submodule (SM) capacitors in MMC are required to be precharged to their nominal voltage values at start-up to ensure MMC work normally. Conventional methods perform the precharging either through grid side or dc side by using costly high-voltage bypass breakers, charging resistors or a high-voltage dc source. Voltage of the high-voltage dc source must be equal to SM capacitor voltage and could be as high as thousands of volts. By contrast, the proposed method employs a very low voltage dc source on dc bus through a series-connected blocking diode, and requires no charging resistor and bypass breakers. It takes advantages of the existing power devices, arm inductors, and SM capacitors in MMC, and configures them into boost circuit for the precharging. The proposed method is simple and cost-effective. Moreover, the characteristics of the boost circuit render the proposed method flexible. For instance, the voltage selection of the dc source is flexible and not restricted to a fixed value. The SM capacitors can be charged in different groups. In addition, the method is applicable to different MMC SMs, including SM with different capacitor voltages. The effectiveness of the proposed method is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

A novel high step-up dc–dc converter with a quasi-active switched-inductor structure for a renewable energy system is presented in this paper. The proposed converter is composed of two coupled inductors which can be integrated into one magnetic core, two capacitors, two active switches, and three diodes. The primary sides of coupled inductors are charged in parallel by the input source, and the secondary sides of coupled inductors are discharged in series with the input source and two capacitors to achieve high step-up voltage gain with an appropriate duty ratio. The two sets of diode–capacitor circuits not only help to lift the voltage conversion gain but also alleviate voltage spike affected by the leakage inductance to limit the voltage stress across the power switch effectively. Therefore, the two low on-state resistance switches can be adopted to reduce conduction loss. Furthermore, the two diodes have no reverse-recovery problem due to turn off naturally, the reverse-recovery problem of the output diode is also alleviated by the leakage inductor and lower part count is needed; therefore, the power conversion efficiency can be further improved. The operating principles and steady-state analyses are discussed in detail; then, the performance of the proposed converter is compared with existing converters. Finally, a prototype is established in the laboratory, and the experimental results are given to verify the correctness of the analysis. [ABSTRACT FROM AUTHOR]

The aim of this paper is to present a new structure for switched-capacitor multilevel inverters (SCMLIs) which can generate a great number of voltage levels with optimum number of components for both symmetric and asymmetric values of dc-voltage sources. The proposed topology consists of a new switched-capacitor dc/dc converter (SCC) that has boost ability and can charge capacitors as self-balancing by using the proposed binary asymmetrical algorithm and series–parallel conversion of power supply. The proposed SCC unit is used in new configuration as a submultilevel inverter (SMLI) and then, these proposed SMLIs are cascaded together and create a new cascaded multilevel inverter (MLI) topology that is able to increase the number of output voltage levels remarkably without using any full H-bridge cell and also can pass the reverse current for inductive loads. In this case, two half-bridge modules besides two additional switches are employed in each of SMLI units instead of using a full H-bridge cell that contribute to reduce the number of involved components in the current path, value of blocked voltage, the variety of isolated dc-voltage sources, and as a result, the overall cost by less number of switches in comparison with other presented topologies. The validity of the proposed SCMLI has been carried out by several simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Modular multilevel converter (MMC) is a promising new topology for high-voltage applications. The MMC is made of several identical submodules. For proper operation, each submodule can be considered as a controlled voltage source where capacitor’s voltage should be maintained at a certain level. Besides, the minimization of the circulating current, which does not flow to the load, is crucial for achieving stable and efficient operation of the MMC. The interrelations among the load current, circulating current, and capacitor voltages complicate the MMC control. This paper aims to achieve stable and balanced voltage and current control with reduced circulating current in various operating conditions. The proposed control uses weighted model predictive control based on a normalized cost function to select the inverter switching patterns, which control the load current, while minimizing voltage fluctuation and circulating current. The weighting factors were selected based on minimizing the load-current total harmonic distortion (THD) and circulating current. The analysis is conducted on a low-power case study of single-phase four-cells MMC with possible extension to higher number of cells. The low-power three-level prototype is designed and built to validate this proposed method. Theoretical analysis, simulation, and experimental results are presented and compared. Parameter sensitivity analysis was also conducted. They all confirm the effectiveness of the proposed control method. [ABSTRACT FROM PUBLISHER]

In recent years, modular multilevel converters (MMCs) are very popular in medium/high-voltage motor drive systems and high-voltage direct-current (HVDC) applications. The conventional model predictive control (MPC) strategies for the MMC are not practical due to their substantial calculation requirements, especially under high number of voltage levels. To solve this problem, a fast MPC strategy combined with a submodule (SM)-voltage sorting balancing method is proposed based on the discrete mathematical model derived for the MMC in this paper. By optimizing the implementation of the control objectives and simplifying the rolling optimization, the proposed strategy is simpler to expand to a system with larger number of SMs, with the amount of calculation reduced and the advantages of the conventional MPC algorithm reserved. In addition, the proposed control can minimize the $dv/dt$ of the output voltages. Both steady-state and transient performances are evaluated by a down-scaled three-phase MMC prototype under various experimental conditions, which validates the proposed fast MPC strategy. [ABSTRACT FROM PUBLISHER]

This paper presents a novel two-stage buck-boost converter with a soft switching operation. The proposed converter is constructed of two identical buck-boost converters working in parallel. The converter units are connected to each other by an inductor as a bridge. This inductor plays an important role in the soft switching operation of the converter by maintaining the voltage applied to switches at zero at switching intervals. The utilized method is called the zero-voltage switching. It is shown that the structure of the proposed converter is significantly efficient in the reduction of switching losses, leading to the improvement of the converter efficiency. Moreover, because of the parallel operation of two identical converters, the output voltage and the input current contain fewer ripples than those of a single converter with the same specifications. Also, utilizing only one inductor as an extra element to achieve this goal makes the proposed converter more economical and reliable with a simpler structure. The detailed analysis of the circuit operation is provided in eight modes. The proposed method is implemented in a laboratory test circuit within the range of 100–220 W output power validating the accuracy of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a new family of zero-voltage-transition (ZVT) bidirectional converters are introduced. In the proposed converters, soft-switching condition for all semiconductor elements is provided regardless of the power flow direction and without any extra voltage and current stress on the main switches. The auxiliary circuit is composed of a coupled inductor with the converter main inductor and two auxiliary switches. The auxiliary switches benefit from significantly reduced voltage stress and without requiring floating gate drive circuit. Also, by applying the synchronous rectification to the auxiliary switches body diodes, conduction losses of the auxiliary circuit are reduced. In the auxiliary circuit, the leakage inductor is used as the resonant inductor and all the magnetic components are implemented on a single core which has resulted in significant reduction of the converter volume. In the proposed converters, the reverse recovery losses of the converter-rectifying diodes are completely eliminated and hence, using the low-speed body diode of the power switch as the converter-rectifying diode is feasible. The theoretical analysis for a bidirectional buck and boost converter is presented in detail and the validity of the theoretical analysis is justified using the experimental results of a 250-W prototype converter. [ABSTRACT FROM PUBLISHER]

The large number of voltage levels in a modular multilevel converter (MMC) make staircase modulation a feasible alternative, particularly in high-power applications. However, staircase waveforms do not necessarily mean operation of the MMC submodules (SMs) at the fundamental frequency. This paper presents an analysis of SM switching frequencies in staircase-modulated MMCs and their correlation to the modulation index and load phase angle. A carrier-based pulsewidth-modulation (CB-PWM) equivalent technique is also developed. This analysis demonstrates that CB-PWM techniques provide a similar switching frequency with superior harmonic performance and improved voltage balancing characteristics at all modulation indices compared to staircase modulation. The theoretical analysis is verified with extensive simulation results for MMCs with different SMs and experimental results from a laboratory prototype. [ABSTRACT FROM PUBLISHER]

The three-phase series-connected modular multilevel converter (SC-MMC) is presented as one option for high-voltage direct current (HVDC) tap to reduce the cost of an HVDC station. Compared with conventional three-phase parallel-connected MMC, the number of semiconductor switches in SC-MMC is reduced by one-third to withstand the same dc voltage. First, the paper studies the operating principle of SC-MMC, and then presents an interspacing phase-shifted pulsewidth-modulated method which could improve the waveform of the output ac voltage for a given switching frequency. Next, the control strategy based on the identical real power input of each phase is proposed to balance the dc voltage of each phase under an unbalanced grid condition. The current limit of switching devices is also taken into consideration to protect SC-MMC from overcurrent. Furthermore, a universal zero-sequence current controller is developed as one part of the control strategy. In addition, an innovative method to suppress the third harmonics of ac current is presented. With the third harmonic suppression strategy, the SC-MMC can operate with much smaller SM capacitors without deteriorating the ac current, which contributes to the cost reduction further. Finally, simulation results obtained in PSCAD/EMTDC are provided to validate the proposed control strategies. [ABSTRACT FROM PUBLISHER]

This paper presents an efficient single-switch boost-dual-input flyback power factor correction (PFC) converter. To achieve a high power factor, a boost PFC cell operating in discontinuous conduction mode is presented. A dual-input flyback dc–dc module, which consists of parallel primary windings and serial secondary windings, operating in critical conduction mode is introduced for galvanic isolation and valley-switching operation. In addition, the proposed converter features high efficiency because the input power is equally divided, and some power is directly transferred to the load by the dual-input flyback dc–dc module. The remaining power is stored in dc-bus capacitors, and it is closely related to the holdup time. Moreover, the currents in the leakage inductors are absorbed by the dc-bus capacitors through a snubber diode, and they are reprocessed by the dual-input flyback dc–dc module. Consequently, the peak voltage in the MOSFET drain is clamped, and the total power conversion efficiency is improved. To verify the performance of the proposed converter, the operating principles, steady-state analysis, and experimental results from a 48 V, 100 W prototype are presented. [ABSTRACT FROM PUBLISHER]

The analysis of a novel single-active-switch-based zero voltage and zero current switching (ZVZCS) tapped boost converter in the discontinuous conduction mode (DCM) is proposed in this paper. The ZVZCS converter includes a lossless snubber composed of three diodes and two capacitors and exhibits novel ZVZCS operation for wide operating ranges of duty cycles, load currents, and input voltages. The voltage stress of the active switch is always less than the load voltage, and soft switching turn-on and turn-off are achieved without cumbersome current or voltage sensing, which could not have been obtained from quasi-resonant converters that also have an active switch. Detailed analyses of the DCM and the component stresses of the proposed converter are presented. Experiments for a 450-W prototype exhibited 99.0% of the maximum efficiency with a SiC JFET at the switching frequency of 50 kHz, and the ZVZCS operation is guaranteed, even for the DCM under the experimental conditions. Moreover, the proposed ZVZCS principle has been applied to a tapped buck–boost converter case, which was also experimentally verified. [ABSTRACT FROM AUTHOR]

In this paper, a high step-down bidirectional converter, utilizing one coupled inductor and two energy-transferring capacitors, is presented. In the step-down mode, the capacitor is connected between input voltage and coupled inductor, which plays a role to step down the input voltage. Therefore, the corresponding voltage conversion ratio is much lower than that of the traditional buck converter and also can be lower than that of the tapped-inductor buck converter. Moreover, the output voltage varies with the duty cycle linearly, making control easier. In the step-up mode, one capacitor is first charged by the coupled inductor, and then releases the energy along with the coupled inductor and the other capacitor connected in series. Therefore, a higher voltage gain can be obtained. Furthermore, the leakage inductance energy can be recycled. Therefore, the switching losses can be reduced and the efficiency can be improved. In this study, the operating principles and experimental results are provided to verify the effectiveness and performance of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, an asymmetrical half-bridge (AHB) converter employing a new center-tapped zeta rectifier (CTZR) is proposed to achieve a high efficiency in wide-input-voltage and low-output-current applications. Due to the proposed CTZR with high dc conversion ratio and extended maximum duty cycle above 0.5, the transformer turns ratio of the proposed converter can be increased, which decreases the transformer dc-offset current compared with that of the AHB converter. Therefore, its transformer core size is decreased. Moreover, it has a wide zero-voltage-switching range with small transformer leakage inductor, which improves light and medium load efficiency. Furthermore, since it has low voltage stress on the secondary diode, its conduction loss can be reduced. In addition, due to the elimination of a diode, the snubber loss in the secondary side is reduced compared with the AHB converter. Therefore, the proposed converter can achieve a higher efficiency compared with the AHB converter without additional devices. To confirm the operation, features, and validity of the proposed converter, a 250–400 V input and 50 V/250 W output laboratory prototype is built and tested. [ABSTRACT FROM AUTHOR]

This paper presents techniques to enable non-isolated boost converters to achieve high power efficiencies under high switching frequency and high-voltage conditions. A quasi-square-wave zero-voltage switching (QSW-ZVS) boost converter topology is proposed to achieve high-frequency soft switching without any coupled inductors in the power stage and, thus, minimize the switching power loss of the converter. An on-chip dynamic dead-time controller is developed to provide near-optimum dead time for power FETs during switching transitions under different output voltage and load current conditions in order to achieve ZVS with minimal body diode conduction loss of power FETs. A synchronous gate driver is also proposed to provide fast propagation delays and output signal rise/fall time, enabling megahertz operation of the converter. A hardware boost converter prototype is built with the synchronous gate driver circuitry implemented in a 0.5-μm high-voltage CMOS process. The proposed QSW-ZVS boost converter provides an output voltage of 150 V and delivers an output power of 130 W. The peak power efficiency of the proposed converter achieves 92.7% at the switching frequency of 1 MHz. Compared with state-of-the-art gate drivers, the worst-case propagation delay of the proposed synchronous gate driver is improved by at least 7.6 times. The operation frequency of the proposed non-isolated boost converter is also improved by at least 15 times compared with other state-of-the-art counterparts. [ABSTRACT FROM AUTHOR]

This paper proposes a resonant dual-active bridge (DAB) converter, which uses a tuned capacitor–inductor–capacitor network. In comparison to the conventional DABs, the proposed topology significantly reduces the bridge currents, lowering both conduction and switching losses and improving the bridge power factors. A mathematical model, which predicts the behavior of the proposed system, is presented to show that both the magnitude and direction of the power flow can be controlled through either relative phase angle or pulse width modulation of voltages produced by the bridges. The viability of the proposed concept is verified through simulation. Experimental results of a 4- kW prototype converter, which has an efficiency of 95% at rated power, are also presented with discussions to demonstrate the improved performance of this topology. [ABSTRACT FROM AUTHOR]

As electrolytic capacitor is apt to fail in power circuits, it is very important to identify its electrical parameters, mainly the equivalent series resistance (ESR) and capacitance (C). A noninvasive online identification method of capacitor's ESR and C for continuous-conduction-mode (CCM) buck converter is proposed in this paper. Based on the ac component of capacitor voltage, the calculation model is founded. By sampling the pulse width modulation signal and output voltage, the method needs no current sensor and is effective for the CCM buck converter operating at different conditions. Implementation of the identification system is presented. The tests are carried out for different aged capacitors and ambient temperatures. The experimental results validate the effectiveness of the method. [ABSTRACT FROM AUTHOR]

Recently, the various types of the half-bridge (HB) converters with the output inductor have been developed, and they exhibit a good performance in medium power applications such as the server power supplies and personal computer power supplies requiring high output current. However, they have common problems such as the primary and secondary switch turn-off losses and snubber loss in the secondary side caused by the output inductor, which degrades light load efficiency. To relieve these limitations of the conventional HB converters, a new HB converter, which employs one additional switch and capacitor in the secondary side, is proposed for a high efficiency under light load conditions in this paper. Since the proposed converter operates like the HB LLC converter with below operation by turning on additional switch under light load conditions, the switch turn-off losses and snubber loss can be minimized, and the zero-voltage switching (ZVS) capability can be improved. Consequently, the proposed converter can achieve a high efficiency under light load conditions. To confirm the operation, features, and validity of the proposed converter, a 330–400 V input and 12 V/300 W output laboratory prototype is built and tested. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage balancing method for stacked multicell converters (SMCs) based on phase-disposition pulse-width modulation (PD-PWM). In order to reduce the switching transitions of the power devices, only optimal transitions between consecutive voltage levels are used. Selection of the optimal transition sequence is performed by evaluating a cost function. Significant reductions in the switching transitions and power losses of the power devices are achieved as compared to the optimal-state voltage balancing method where nonoptimal transitions are allowed. Simulation and experimental results from a seven-level $3\times 2$ SMC verifies that the proposed PD-PWM voltage balancing method is robust under linear/nonlinear loads and transients. [ABSTRACT FROM AUTHOR]

This paper presents a novel digital converter for a contactless displacement transducer. The sensor part of the proposed transducer employs a floating (contactless) wiper that moves over a resistive element. A novel signal-conditioning circuit presented here operates on the contactless resistive potentiometer element and provides a digital output that linearly varies with the position of the wiper. The signal-conditioning circuit is developed such that the digital output is independent of the coupling capacitor that arises between the floating wiper and the resistive element, thus eliminating the effect of any jitter that may arise in the movement of the wiper. Results from a prototype circuit built and tested using a prototype sensor establish the efficacy of the proffered scheme. [ABSTRACT FROM PUBLISHER]

This paper proposes a new isolated three-port bidirectional dc–dc converter for simultaneous power management of multiple energy sources. The proposed converter has the advantage of using the least number of switches and soft switching for the main switch, which is realized by using an inductor–capacitor–inductor ( $LCL$) -resonant circuit. The converter is capable of interfacing sources of different voltage–current characteristics with a load and/or a dc microgrid. The proposed converter is constructed for simultaneous power management of a photovoltaic (PV) panel, a rechargeable battery, and a load. Simulation and experimental results show that the proposed converter is capable of maximum power point tracking control for the PV panel, when there is solar radiation, and controlling the charge and discharge of the battery, when there is surplus energy and power deficiency with respect to the load, respectively. [ABSTRACT FROM PUBLISHER]

A single-objective predictive control method that deals with four main control objectives applied to a multivariable single-phase three-level neutral-point-clamped converter operating as an active power filter is proposed in this paper. The four control objectives are to self-support the dc-bus voltage under load variations, to compensate the reactive power and the current harmonics, and to balance the dc capacitor voltages by using a predefined combination of the redundant switching states of the converter. The main contribution of the proposed method is that these objectives are accomplished without using weighting factors in the cost function, which eliminates problems such as multiobjective optimization or additional empirical procedures for determination of these factors. As a result, the method is easy to implement and rapidly selects the optimal voltage to improve the dynamic-state performance. Experimental results from a 2-kVA prototype are presented to prove that the method is valid for single-phase compensation. The well-known effect of model parameter errors' issue, which is inherent in predictive control methods, is also tested to confirm that the harmonic distortion in the grid current is below 5% even when the predictive model has a 25% error between actual and theoretically estimated grid impedance values. [ABSTRACT FROM PUBLISHER]