Search

In applications that demand single-input dual-output (SIDO) or dual-input single-output (DISO) dc–dc converters, employing two separate single-input single-output (SISO) converters is a solution. However, the number of components is doubled, resulting in high overall cost. In order to reduce costs, this paper proposes a novel topology synthesis methodology, with which a variety of SIDO and DISO dc–dc converters with reduced components can be derived. The principle of topology synthesis states that integrated SIDO and DISO dc–dc converters can be easily developed from conventional SISO converters by replacing a diode with a basic cell inclusive of additional input/output port. The principle is effective for many SISO dc–dc converters, and as an example, topology synthesis based on buck, boost, buck–boost, Cuk, sepic, and zeta SISO converters is performed in this paper. In order to achieve better understanding of the proposed converters, the integrated SIDO Cuk converter is specifically analyzed and experimentally verified. In comparison with the conventional scheme of two separate SISO Cuk converters, good cross regulation is retained while the number of diodes, inductors, and capacitors is reduced in the proposed SIDO Cuk converter. In addition, zero-voltage-switching operation of one switch is achieved, contributing to lower switching losses. Finally, a prototype circuit with 48-V input and 156 V/1 A, 24 V/4 A outputs is built to validate the theoretical analysis. [ABSTRACT FROM PUBLISHER]

A switched-capacitor-based dual-switch dc–dc converter with a high-boost voltage gain is proposed in this paper. The proposed converter can obtain a high-voltage gain with a small duty cycle, which decreases the voltage stress and the conduction loss on the power switches. This paper presents the key waveforms, the operating principles at the continuous conduction mode and the discontinuous conduction mode, and the parameter design. Moreover, a comparison between the proposed converter and other nonisolated converters has been completed. To verify the operating principle, a 200 W prototype is constructed with an input voltage of 25–50 V and an output voltage of 200 V. The simulation and experimental results are shown. [ABSTRACT FROM PUBLISHER]

The power efficiency and weight of present point-of-load (POL) dc–dc converters for drone applications are often compromised because they suffer from large switching losses at continuous conduction mode for heavy loads and excessive hardware overheads at discontinuous conduction mode for light loads. This paper presents a boundary conduction mode (BCM) control scheme for POL converters embodying a single operation mode. This is achieved by means of a hysteresis voltage controller to turn on/off the output power stage when necessary. The proposed BCM control scheme achieves high power efficiency (≥91.2%) over a wide load range (5 mA–1 A) by means of fully soft switching. Specifically, a hysteretic current controller is proposed to realize ZCS, and an adaptive dead time controller is proposed to realize ZVS. Further, the proposed BCM control scheme requires a small output inductor (0.82 μH) by means of designing the customizable peak inductor current. To verify the proposed BCM control scheme, we realize a BCM-based POL converter that features an input voltage range of 5–16 V, output voltage range of 2.5–8 V, switching frequency of 1.5 MHz, peak power efficiency of 96.8%, and ≤35 mV output voltage undershoot/overshoot for 1-A load step. When being benchmarked against state-of-the-art counterparts, the proposed design features the lowest voltage undershoot/overshoot, the highest switching frequency, ∼5.7× smaller inductor, and ∼11% higher power efficiency at light loads. [ABSTRACT FROM AUTHOR]

When the interleaved boost power-factor correction (PFC) converter operates in a light load (<15% of nominal load), the phase-shedding control is commonly used to increase the converter's efficiency. If the inductors are coupled for high power density applications, because of the strong mutual effects of the coupled inductor, the switching of the operation phase may lead to a current flowing in the non-operation phase. In this paper, a two-phase interleaved boost PFC converter with a coupled inductor in the single-phase operation was analyzed. The operation modes of the converter in a switching cycle and a half line cycle were presented, and the modes’ variation with the load changes, as well as the power distribution, was provided. A 1-kW prototype was built to verify the analysis, and it was shown that the non-operation phase also delivers some power, which may worsen the converter's efficiency and distort the average input current waveform. [ABSTRACT FROM AUTHOR]

This paper presents a delta-sigma modulation (DSM) control scheme for noninverting buck–boost (NIBB) converter that features a duobinary encoding for four power switch controls. The proposed scheme converts the single-bit output of the modulator into a 1.5-b signal to enable a three-phase operation comprising the charging, bypassing, and discharging phases. This control method reduces both switching and conduction losses by changing only two switches in each period, thus, achieving high conversion efficiency. A smooth mode transition is provided by the DSM controller, which automatically and continuously determines the operating mode of the converter. Thus, the dead zone can be effectively released with improved transient responses. Furthermore, the spurious tones in the output are effectively eliminated by the robust noise shaping capability of the modulator. The proposed DSM-based NIBB converter was implemented on a 180-nm CMOS. It regulated the output in the range of 2.0–4.6 V with input voltage of 2.5–5.0 V, and the maximal load current was 500 mA. The converter showed a peak efficiency of 94.8% at 90-mA load and the output voltage ripples were maintained under 18 mV. A low noise floor with the first spurious peak located –92 dBc below the signal was achieved across all mode operations. In addition, the converter occupied a small chip area of 1.51 mm2. [ABSTRACT FROM AUTHOR]

To reduce current stress and improve efficiency of dual active bridge (DAB) dc–dc converters, various control schemes have been proposed in recent decades. Most control schemes for directly minimizing power losses from power loss modeling analysis and optimization aspect of the adopted converter are too difficult and complicated to implement in real-time digital microcontrollers. Thus, this paper focuses on a simple solution to reduce current stress and improve the efficiency of the adopted DAB converter. However, traditional current-stress-optimized (CSO) schemes have some drawbacks, such as inductance dependency and an additional load-current sensor. In this paper, a simple CSO scheme with a unified phase-shift (UPS) control, which can be equivalent to the existing conventional phase-shift controls, is proposed for DAB dc–dc converters to realize current stress optimization. The simple CSO scheme can overcome those drawbacks of traditional CSO schemes, gain the minimum current stress, and improve efficiency. Then, a comparison of single-phase-shift (SPS) control, simple CSO scheme with dual-phase-shift (CSO-DPS) control, simple CSO scheme with extended-phase-shift (CSO-EPS) control, and simple CSO scheme with UPS (CSO-UPS) control is analyzed in detail. Finally, experimental results verify the excellent performance of the proposed CSO-UPS control scheme and the correctness of theoretical analysis. [ABSTRACT FROM AUTHOR]

In more electric aircraft (MEA), three-phase power factor correction (PFC) rectifiers of several kilowatts are required. In this paper, a three-phase buck–boost derived PFC converter with three switches and with input inductors connected in delta configuration for use in MEA is presented. The proposed converter is operated in a discontinuous conduction mode to achieve PFC at ac input. This avoids the inner current control loop which further eliminates the current sensors. It requires only one output voltage sensor unlike five sensors in conventional PFC converter for its control implementation. This makes the system cost effective, more reliable, and robust. A simple voltage control loop is used to generate the gate signals. The steady state operation of the converter and detailed design calculations are presented. For each power component, the analytical expressions for calculating the average and rms current ratings are derived to facilitate the converter design. The small-signal model of the converter is presented to aid the controller design. The experimental results from a 2 kW laboratory prototype are presented to confirm the operation of the proposed converter. An input power factor of 0.999, an input current total harmonic distortion of as low as 2.76%, and a high conversion efficiency of 96% are achieved from the prototype. [ABSTRACT FROM AUTHOR]

MR16 lighting system with a high-frequency step-down electronic transformer is widely used in commercial lighting. In this paper, a single-switch quadratic boost light emitting diode (LED) driver compatible with electronic transformers for the MR16 lighting system is proposed and analyzed. It combines a prestage boost power factor correction (PFC) converter and a second-stage boost dc–dc converter with a single switch. The effect of the dc link voltage ripple of the prestage boost PFC converter on the output of the second-stage boost dc–dc converter is eliminated by a fast voltage mode control loop of a second-stage circuit. Therefore, flicker-free low ripple LED current is achieved. With a small dc link voltage ripple of prestage, the turn-on time of the active switch is almost constant in a half-line cycle. Therefore, PFC can be achieved with inductor current of prestage operating in a discontinuous conduction mode. With small input capacitance, the proposed LED driver presents a good compatibility performance with different kinds of electronic transformers. Furthermore, the proposed LED driver needs only one active switch and one control loop, which makes circuit volume small and low cost. Finally, a 4 W LED driver for a small-size MR16 lighting system is provided to verify the studied results. [ABSTRACT FROM AUTHOR]

Single-stage power-factor-corrected (S2PFC) power supplies usually suffer from high voltage stress, due to lack of control on the intermediate bus capacitor voltage. In the past, analysis of such voltage stress was mostly based on steady-state condition without providing sufficient explanation during the transient circuit operation. This paper revisits the problem at circuit level and reports that the root cause is due to the inherent negative current feedback property of the output inductor or the transformer operating in continuous conduction mode (CCM). Based on the finding, this paper further proposes a new approach to reducing the voltage stress by adding an auxiliary circuit branch to existing S2PFC converters. The additional circuit branch limits the effect of negative current feedback by suppressing the change of output current slope due to change of load. This assists the pulsewidth modulation controller to track the change of load better such that the bus capacitor voltage range is reduced through duty cycle control. The auxiliary circuit branch also reduces reverse-recovery-related losses of the converter under CCM operation. A laboratory prototype using the popular boost PFC converter combined flyback dc/dc converter was built and tested to confirm the analysis and effectiveness of the approach. [ABSTRACT FROM AUTHOR]

This paper proposes a pulse width modulation plus phase-shift (PPS) control for nonisolated high gain soft-switching bidirectional dc–dc converter (HSBDC). The phase-shift angle is used to control the direction and amount of power flow of the bidirectional dc–dc converter, while the duty cycle is used to balance the voltage between two high voltage side (HVS) capacitors. The HSBDC with PPS control has the advantages of simple control structure and symmetrical switching patterns, ensured soft-switching in both forward and backward modes at all load under wide voltage range, and reduced voltage ratings of the HVS capacitors and switches. The operation principle of the HSBDC with PPS control is analyzed in detail. Based on the analysis the passive component is designed to achieve higher efficiency. A 3-kW prototype is implemented and tested to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

A novel high-conversion-ratio bidirectional dc–dc converter with coupled inductor is proposed in this paper. Compared with the bidirectional converters based on coupled inductor, this new topology can realize a higher step-up voltage gain and lower step-down voltage gain with a lower turn ratio in an appropriate duty cycle. In proposed converter, the windings of the coupled inductor are reversely connected to transfer energy from high voltage source or low voltage source. Then, a clamp capacitor is applied to reduce voltage stress on main switch; therefore, the conduction loss of the main switches can be reduced by using a low resistance switch, and the clamp capacitor can also recycle the energy of the leakage inductor in coupled inductor. Besides, the soft-switching technique is used to achieve zero voltage switching, so the efficiency can be further improved. The main circuit and its steady-state operating principle are analyzed in detail. Finally, a 25–200 V 200 W bidirectional dc–dc converter is implemented to verify its performance. [ABSTRACT FROM AUTHOR]

This paper gives a comprehensive comparison of multilevel high-frequency-link (HFL) dc transformer (abbreviated MDCT) based on modular multilevel converter (MMC) and multilevel-dc-link dc transformer (abbreviated ADCT) based on dual-active-bridge (DAB) for medium-voltage dc (MVDC) application. The topology, operation, HFL voltage and current, active and circulating power, characteristic currents, switching behaviors, and power loss are analyzed in detail. Both MDCT and ADCT have fault treatment ability for MVDC application. However, the installation and commissioning of ADCT are more flexible and simpler. In addition, the MDCT needs more switches and high-frequency (HF) inductors than ADCT in the MVDC side with the same voltage level, but the number of HF transformer can be reduced. Compared with MDCT, the ADCT has higher power transfer ability and lower circulating power, lower HFL voltage, and RMS current and peak values with the same transmission power in the MVDC side. However, the arm RMS and average currents of MDCT are lower than those of ADCT in the MVDC side. The switching performance of MDCT deteriorates when the MVDC voltage fluctuates, but the switching behaviors of half bridges are added to ADCT. The loss of ADCT almost keep the same when the MVDC voltage fluctuates, but the loss of MDCT changes a lot. Finally, a small-scale prototype platform with 1 kW/450 V/150 V is built and experimental results verify the correctness and effectiveness of the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper investigates the use of multilevel conversion in dc–dc applications that require a large voltage conversion ratio. A quantitative method that can serve as a guide to compare and design multilevel topologies for large conversion ratio applications is presented. The proposed method keeps the conduction loss and switching loss constant across the different converters and employs the passive component volume as the single performance metric. As examples, flying capacitor multilevel converters and hybrid switched-capacitor (SC) converters are compared to conventional two-level buck converters, and are shown analytically to have significantly reduced passive component size. Three converter prototypes are implemented, based on the presented methodology to experimentally validate the method as well as demonstrate the advantages of multilevel and hybrid SC converters. [ABSTRACT FROM PUBLISHER]

Three-level buck dc–dc converters have advantages over the traditional buck converters: half switch voltage stress, doubling effective switching frequency, smaller inductor size, and the higher power density. To benefit from those advantages, the flying capacitor voltage must be balanced at half of the input voltage. Most existing methods of balancing the flying capacitor voltage require current sensing, which increases the cost and noise sensitivity. This paper proposes a novel state-machine structure of second-order sliding-mode (SOSM) control for three-level buck dc–dc converters without sensing currents. With insensitivity to parameter variations of SOSM control, the proposed control approach tackles the strongly coupled problem of output voltage and flying capacitor voltage in three-level buck dc–dc converters. Compared to existing approaches, the controller achieves fast start-up without overshoots, fast load disturbances rejection, and robustness against parameter uncertainties for the output voltage, and balance of the flying capacitor voltage without sensing the current of flying capacitor. The proposed approach is verified with experimental results of a 1.25 V, 2.5 A prototype. [ABSTRACT FROM PUBLISHER]

The positive output elementary superlift-Luo converter (POESLLC) is a type of dc/dc converter. This dc/dc converter has an attractive advantage of a high voltage transfer gain as compared with other conventional dc/dc converters. Because of the voltage and load variations and also switching operation, the dynamic and static performances of the POESLLC are nonlinear and time varying. In order to achieve an excellent performance, a nonlinear controller is required. In this paper, a robust and fast response controller for voltage regulation of a POESLLC is presented. A proportional integral and pulse width modulation sliding mode controller are combined to control a third-order POESLLC. The proposed controller can be applied in the continuous conduction mode. Some simulations and experimental results are presented to show the effectiveness of the developed controller in different operating conditions. Furthermore, it will be shown that the developed controller is successful in suppressing the steady-state error of the output voltage of the POESLLC as well as the number of reduction of sensors. [ABSTRACT FROM PUBLISHER]

This paper proposes a current-fed isolated bidirectional dc–dc converter (CF-IBDC) that has the advantages of wide input voltage range, low input current ripple, low conduction losses, and soft switching over the full operating range. Compared with conventional CF-IBDCs, the voltage spikes of the low-voltage (LV) side switches in the proposed converter can be eliminated without additional clamp circuits. The converter adopts the pulse width modulation plus hybrid phase-shift control scheme such that the bus voltage can match the output voltage by means of the transformer. Thus, the current stresses and conduction losses of the converter become lower. In addition, the practical zero voltage switching (ZVS) of the secondary-side switches can be realized by adjusting the phase-shift angle within the secondary side when in light load or no load condition. The operating principles and characteristics including the power transfer, root-mean-square (RMS) current, and soft switching are investigated in detail. Then the design guidelines of inductors are also given. Finally an experimental prototype with 30–60 V input and 400 V/2.5 An output is built to verify the correctness of theoretical analyses. [ABSTRACT FROM PUBLISHER]

To solve some problems caused by the ac control method used for the existing modular multilevel dc–dc converter (MMDC), this paper has proposed a new MMDC topology with a wide range of output voltage by means of dc control. By reconstructing the submodule structure, the converter has a power branch and an auxiliary balance branch, which are used to transmit dc power and balance the capacitor voltage, respectively. Both dc analysis and control method are adopted to establish a mathematical model so as to deduce the mathematical relationships between the key electrical parameters. Moreover, what have been done include analyzing the self-balancing principle of the capacitor voltage and the mechanism of the auxiliary balance branch, calculating the related parameters of the capacitor voltage fluctuation, and presenting a dc closed-loop control strategy based on a small-signal model. The analyses of the steady and dynamic states in combination with simulation and experiment show that the proposed converter can stably operate in the mode of dc control, with a large adjustable range of output voltage, a small fluctuation in voltage of the capacitor, and the ability of the inductor to suppress the spike of the auxiliary balance current effectively so as to reduce the impact on the device. [ABSTRACT FROM AUTHOR]

This paper presents a method of mitigating the transient overshoots of dc-dc converters undergoing large load disturbances. The method involves a small power auxiliary circuit which exists as an energy buffer to provide a smooth absorption and release of excess energy from and to the main dc-dc converter during transients. In the method, the regulation of the current magnitude of the converter and energy storage of the auxiliary circuit are guaranteed by the relevant control schemes. The cost and size of the auxiliary circuit will be relatively small as it only operates intermittently. In this paper, the voltage deviation analysis and the auxiliary circuit design guideline are provided. Experimental results validating the approach are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a novel integrated synchronous buck converter for the auxiliary power supply system of electric vehicles, which achieves multiple independently regulated outputs with reduced switching components in comparison with the conventional separate buck converters. In order to obtain a better understanding of the proposed converter, operational principle and performance characteristics of a simplified dual-output buck converter are introduced in detail, as an example. The analysis shows that zero-voltage-switching operation and lower conduction losses could be attained. In addition, its dynamic behavior is similar to the conventional buck converter and thus the controller design is simple. Finally, experimental results based on a prototype circuit in which two inductors are integrated into one magnetic core to achieve further reduced cost are demonstrated to verify the advantages. [ABSTRACT FROM PUBLISHER]

Single-inductor multiple-output (SIMO) switching dc–dc power converter architecture is a cost-effective alternative to multiple individual switching power converters solution in many power distribution system applications where multiple voltage rails are required at reduced cost. However, with multiple output voltage rails coupled to the same switching node, the SIMO power converters suffer from cross regulation between the multiple outputs, which complicates the closed-loop controller design of the SIMO converter and degrades regulation performance. In this paper, a power-multiplexed (PM) control scheme is proposed aiming to completely decouple the operations of multiple outputs from one another. The proposed PM control scheme results in eliminating the cross regulation among the multiple outputs while maintaining desired voltage regulation performance for each output under both steady-state and dynamic operations. Low-cost microcontroller or analog circuitries can be used to implement the proposed controller. Experimental proof of concept prototype results verify the feasibility and advantages of the proposed controller. [ABSTRACT FROM PUBLISHER]

A family of isolated buck–boost dc/dc converter for wide input-voltage range is proposed in this paper, and the full-bridge (FB) boost converter, being one of the typical topologies, is analyzed. Due to the existence of the resonant inductor (including the leakage inductor), the FB-boost converter can only adopt the two-edge-modulation (TEM) scheme with the FB cell being leading-edge modulated and the boost cell being trailing-edge modulated to minimize the inductor current ripple over the input-voltage range, and a phase-shift-control-scheme-based TEM with the use of the market available controller IC such as UC3895 is proposed, which realizes phase-shifted control for the FB cell to achieve zero-voltage switching. In order to improve the reliability and efficiency of the FB-boost converter, a three-mode dual-frequency control scheme is proposed, in which the FB-boost converter operates in boost, FB-boost and FB modes in low, medium and high input voltage regions, respectively, and for which the expression of the inductor current ripple is derived in this paper. As the input voltage in the FB-boost mode is close to the output voltage, the inductor current ripple in this mode is much smaller than that in the other modes, and the switching frequency of the boost cell in this mode can be lowered to one-(2N+1)th of the preset switching frequency to reduce the switching loss, and hence, to improve the efficiency. A 250–500 V input, 360 V output, and 6 kW rated power prototype is fabricated to verify the effectiveness of the design and control method. The average efficiency over the input-voltage range is 96.5%, and the highest efficiency attained is 97.2%. [ABSTRACT FROM AUTHOR]

A novel high step-up dc–dc converter with a quasi-active switched-inductor structure for a renewable energy system is presented in this paper. The proposed converter is composed of two coupled inductors which can be integrated into one magnetic core, two capacitors, two active switches, and three diodes. The primary sides of coupled inductors are charged in parallel by the input source, and the secondary sides of coupled inductors are discharged in series with the input source and two capacitors to achieve high step-up voltage gain with an appropriate duty ratio. The two sets of diode–capacitor circuits not only help to lift the voltage conversion gain but also alleviate voltage spike affected by the leakage inductance to limit the voltage stress across the power switch effectively. Therefore, the two low on-state resistance switches can be adopted to reduce conduction loss. Furthermore, the two diodes have no reverse-recovery problem due to turn off naturally, the reverse-recovery problem of the output diode is also alleviated by the leakage inductor and lower part count is needed; therefore, the power conversion efficiency can be further improved. The operating principles and steady-state analyses are discussed in detail; then, the performance of the proposed converter is compared with existing converters. Finally, a prototype is established in the laboratory, and the experimental results are given to verify the correctness of the analysis. [ABSTRACT FROM AUTHOR]

It is known that the ripple-based control of a switching dc–dc converter benefits from a faster transient response than a conventional pulse width modulation (PWM) control switching dc–dc converter. However, ripple-based control switching dc–dc converters may suffer from fast-scale oscillation. In order to achieve fast transient response and ensure the stable operation of a switching dc–dc converter over a wide load range, based on a conventional pulse train (PT) control technique, a peak capacitor current PT (PCC-PT) control technique is proposed in this paper. With a buck converter as an example, the operating modes, steady-state performance, and transient respond performance of a PCC-PT controlled buck converter are presented and assessed. To eliminate fast-scale oscillation, circuit and control parameter design considerations are given. An accurate discrete iteration model of a PCC-PT controlled buck converter is established, based on which the effects of circuit parameters on the stability of the converter operating in a discontinuous current mode (DCM), mixed DCM-continuous conduction mode (CCM), and CCM are studied. Simulation and experimental results are presented to verify the analysis results. [ABSTRACT FROM PUBLISHER]

For discontinuous conduction mode (DCM) dc–dc converters with digital sensorless current mode (DSCM) control, an observed current error occurs, owing to a low-accuracy current observer. Moreover, a reference current error occurs due to a low-accuracy current controller or a finite dc gain of current loop. Conventionally, the observed current is compensated to increase current regulation accuracy, whereas the reference current error is neglected. However, for charge balance principle (CBP)-based DSCM (CBP-DSCM) control, this paper proves that the reference current should be compensated in a same quantity to that of observed current. Otherwise, single or unequal compensation leads to output voltage steady-state error. For this reason, a dual current error compensation strategy for CBP-DSCM control is proposed. It compensates the errors in a same quantity through a current error observer, which considers parasitics and calculates the current errors without approximation. To verify the proposed strategy, small-signal models with parasitics for both the converter and the controller are constructed by differential functions of key variables. Furthermore, converter stability is analyzed at typical operation condition, while the stability at various operation conditions is verified through robustness analysis. Finally, simulations and experimental results verify the analysis and the improved transient response of the converter. [ABSTRACT FROM AUTHOR]

This paper proposes a novel 3 $\phi$ stand-alone solar photovoltaic (PV) system configuration that uses high-gain high-efficiency $(\approx\! 96\%)$ dc–dc converters both in the forward power stage and the bidirectional battery interface. The high-voltage-gain converters enable the use of low-voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. In addition, the proposed configuration facilitates “required power tracking (RPT)” of the PV source as per the load requirements, eliminating the use of expensive and “difficult to manage” dump loads. High-performance inverter operation is achieved through $abc$ to $dq$ reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage, and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulsewidth modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation, and experimental results of this work are presented. [ABSTRACT FROM PUBLISHER]

This paper presents high step-up dc-to-dc converter for low voltage sources such as solar photovoltaics, fuel cells, and battery banks. To achieve high voltage gain without large duty cycle operation, combination of coupled inductor and switched capacitor voltage doubler cells are used. By incorporating active clamp circuit, voltage spike due to the leakage inductance of the coupled inductor is alleviated and zero-voltage switching turn on of the main and auxiliary switch is obtained. Due to the use of MOSFETs of low voltage rating and soft turn on of the switches, conduction loss and switching losses are reduced. This improves the efficiency and power density of the converter. The proposed converter can achieve high voltage gain with reduced voltage stress on MOSFET switches and output diodes. Design and analysis of the proposed converter is carried out, and finally, a 500-W experimental prototype is built to verify theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel multiple-input bidirectional dc–dc power converter to interface more than two dc sources of different voltage levels. This finds applications in hybrid electric/fuel cell vehicles (FCVs), where different dc sources of unequal voltage levels need to be connected with bidirectional power flow capability. The converter can be used to operate in both the buck and boost modes with bidirectional power control. It is also possible to independently control power flow between any two sources when more than two sources are actively transferring power in either directions. The operation, analysis, and design of the converter are presented with different modes of power transfer. The proposed converter is demonstrated for FCV application using real-time hardware-in-the-loop system. Experimental results for a 5-kW system are presented, validating the theoretical analysis. [ABSTRACT FROM PUBLISHER]

For low-cost isolated ac/dc power converters adopting high-voltage dc-link, research efforts focus on single-stage multilevel topologies. This paper proposes a new single-stage three-level isolated ac/dc PFC converter for high dc-link voltage low-power applications, achieved through an effective integration of ac/dc and dc/dc stages, where all of the switches are shared between two operations. With the proposed converter and switching scheme, input current shaping and output voltage regulation can be achieved simultaneously without introducing additional switches or switching actions. In addition, the middle two switches are turned on under zero current in discontinuous conduction mode operation, and the upper and bottom switches are turned on under zero voltage. Due to the flexible dc-link voltage structure, high power factor can be achieved at high line voltage. A 500 W/48 V prototype is designed to serve as the proof of concept, which exhibits 90.8% peak efficiency at low input line voltage. [ABSTRACT FROM AUTHOR]

This paper presents a high-efficiency dc-dc boost converter to interface a miniaturized 50 μL microbial fuel cell (MFC) having 1 cm2 vertically aligned carbon nanotube anode and 1 cm2 Cr/Au cathode. Geobacteraceae-enriched mixed bacterial culture in growth medium and 100 mM buffered ferricyanide solutions are used as the anolyte and catholyte, respectively. The miniaturized MFC produces up to approximately 10 μW with an output voltage of 0.4-0.7 V. Such low voltage, which is also load dependent, prevents the MFC to directly drive low power electronics. A pulse-frequency modulation type dc-dc converter in discontinuous conduction mode is designed and implemented to address the challenges and provides a load independent output voltage with high conversion efficiency. The fabricated dc-dc converter in UMC 0.18 μm has been tested with the MFC. At 0.9 V output, the converter has a peak efficiency of 85% with 9 μW load. [ABSTRACT FROM AUTHOR]

High efficiency and high power density can be achieved with a dc-dc transformer by operating all the switches at a fixed 50% duty cycle. However, the output voltage of the dc-dc transformer cannot be regulated. Novel rectifiers named active boost rectifiers (ABRs) are proposed in this paper. Basically, an ABR is composed of a traditional diode rectifier and a bidirectional switch. By adopting phase-shift control between the primary- and secondary-side switches, the output voltage regulation can be achieved when introducing the ABR to a dc-dc transformer. As a result, a family of novel soft-switching dc-dc converters is harvested. When the proposed converter operates in the soft-switching continuous conduction mode, zero-voltage-switching (ZVS) performance for all the primary- and secondary-side switches is achieved. When the converter operates in the discontinuous conduction mode, zero current switching (ZCS) for the primary-side switches and ZVS for the secondary-side switches are achieved. Furthermore, the diode reverse-recovery problem is alleviated by employing the ABR and phase-shift control scheme. As an example, the full-bridge converter with voltage-doubler ABR is analyzed to verify the proposed ABR concept and converters. The operation principles, voltage conversion ratio, and output characteristics are analyzed in depth. Finally, experimental results are provided to verify the feasibility and effectiveness. [ABSTRACT FROM AUTHOR]

The propagation delay of a comparator and dead time causes the duty-discontinuity region near the boundary of the step-down and step-up regions in a non-inverting buck–boost (NIBB) converter. The duty-discontinuity region leads to an unstable output voltage and an unpredictable output voltage ripple, which might cause the entire power system to shut down. In this paper, a mode-transition technique called duty-lock control is proposed for a digitally controlled NIBB converter. It locks the duty cycle and eliminates the error between the output voltage and the reference signal by using a proposed fixed reference scheme that ensures the stability of the digital controller and output voltage. The experimental results that were applied to a field-programmable gate array-based platform revealed that the output voltage of the NIBB converter is stable throughout the entire transition region, without any efficiency tradeoffs. The input voltage of the converter that was provided by a Li-ion battery was 2.7–4.2 V, and the output voltage was 1.0–3.6 V, which is suitable for radio-frequency power amplifiers. The switching frequency was 500 kHz, and the maximum load current was 450 mA. [ABSTRACT FROM PUBLISHER]

In this paper, a novel bidirectional modular multilevel dc-dc converter is proposed. The proposed topology, named the triangular modular multilevel dc-dc converter (TMMC), can achieve equal power sharing among its modules over a broad range of conversion ratios. The proposed control algorithm provides localized control of modules which enhances the converter's dynamic performance and design flexibility. A 1.7-kW experimental implementation of the converter is shown to achieve an efficiency of 95.9% and 96.2% in step-up and step-down modes, respectively. Significant reductions in the input current and output voltage ripples are observed through the interleaved operation of the converter. The TMMC also provides multiple fixed voltage nodes which makes it suitable as a multiple-input multiple-output converter. [ABSTRACT FROM AUTHOR]

This paper introduces a modular multilevel dc/dc converter, termed the DC-MMC, that can be deployed to interconnect HVDC networks of different or similar voltage levels. Its key features include: 1) bidirectional power flow; 2) step-up and step-down operation; and 3) bidirectional fault blocking similar to a dc circuit breaker. The kernel of the DC-MMC is a new class of bidirectional single-stage dc/dc converters utilizing interleaved strings of cascaded submodules. The DC-MMC operation is analyzed and an open loop voltage control strategy that ensures power balance of each submodule capacitor via circulating ac currents is proposed. Simulations performed in PLECS validate the DC-MMC's principle of operation and the proposed control strategy. Experimental results for a 4-kW laboratory prototype illustrate the single-stage dc/dc conversion process for both step-down and step-up operating modes. [ABSTRACT FROM AUTHOR]

For a sensorless predictive current controlled boost dc–dc converter, its small-signal model that contains a number of parasitic parameters, is derived in this paper. This model indicates that the type of system becomes type 0 even with the correction of voltage loop proportional–integral controller, leading to the existence of output voltage steady-state error. Then a self-correction differential current observer (SDCO) is proposed to eliminate this steady-state error and gain high transient response speed. The self-correction part of the SDCO makes the system become type 1 to achieve no steady-state error for output voltage, whereas the differential part can guarantee that the intermediate calculation results do not overflow. By carrying out a series of simulation verifications, further investigation proves that the proposed algorithm has good robustness. Finally, the effectiveness of the proposed algorithm is verified by experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a new nonisolated buck/boost-type multilevel dc–dc converter suitable for high-power and medium/high-voltage application. The main features of the proposed topology are as follows: low voltage across the semiconductors, low switching losses, and reduced volume of the output filter. The theoretical analysis is carried out for a five-level bidirectional structure of the proposed converter, operating in Buck mode. The proposed topology presents some capacitors, and their voltage must be balanced for proper operation of the converter. Thus, a capacitor voltage balancing active control using a feedforward technique is proposed and analyzed in detail. In order to validate the theoretical analysis, a prototype with 10 kW output power capability, 1.3 kV to 800 V input-to-output voltage, and 20 kHz of switching frequency was built and experimented. The results attest the advantages of the new dc–dc topology, as well as the new capacitor voltage control technique. [ABSTRACT FROM AUTHOR]

This paper unifies the underlying concepts of all basic single-switch, two-state, dc-to-dc voltage-sourced converters, by duality, as generic related current and voltage-sourced converters. By using ac and dc circuit theory, the three basic converters can be transformed to yield all known transfer functions and realizes a proliferation of 33 topologies, three being previously unidentified topologies with unique characteristics. The circuit based systematic unifying approach offers new insight and an alternative interpretation to the origin of the 33 topologies including the Zeta, Cuk, \pmLuo, CSC, Landsman, and Sepic converters. Converter time-domain simulations and corresponding practical results of the three new topologies extol and culminate the concepts and analysis presented. [ABSTRACT FROM PUBLISHER]

The pulse-train (PT) control technique for switching dc–dc converters is simple to design and benefits from excellent control performance. Up to now, almost all of the works on PT control are focused on switching dc–dc converters operating in discontinuous conduction mode, with few works reported on PT control of switching dc–dc converters operating in continuous conduction mode (CCM). In this paper, a PT-controlled CCM buck converter is studied and a unique low-frequency oscillation phenomenon is revealed, which results in large undesired inductor-current and output-voltage variations. The effect of equivalent series resistance (ESR) output-capacitor on the low-frequency oscillation is examined. The results indicate that such oscillation occurs when the ESR output-capacitor is relatively small and disappears when it is relatively large. However, a larger ESR will result in a large output-voltage ripple. In order to avoid the low-frequency oscillation and, at the same time, to ensure a small output-voltage ripple, the ICRIF circuit is applied. In this way, a small ESR output-capacitor can be used to decrease the output-voltage ripple. Simulation and experimental results are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a photovoltaic (PV)-system maximum power point (MPP) tracking (MPPT) control strategy employing a predictive digital current-controlled converter implemented in conventional hardware resources is presented. Two current programmed controllers (finite-state predictive control and valley current control) have been integrated into a system with current- or voltage-oriented MPPT. The modifications applied to the perturb-and-observe algorithm enable the MPP tracker to interact rapidly with the controller accounting also for abrupt irradiance drops by considering voltage and current limitations. The implementation of digital control in PV systems entails significant advantages of speed and accuracy, although the controller converges correctly at the MPP under irradiance variations featuring fast dynamic response. The proposed controller scheme has been experimentally demonstrated on a digitally current-controlled boost converter delivering power from a PV system. [ABSTRACT FROM PUBLISHER]

In this paper, a soft-switching dc/dc converter with secondary-side phase-shift control strategy is proposed to improve the conversion efficiency and minimize the primary switch voltage stress in the high input voltage applications. Zero-voltage-switching performance is achieved for both the primary- and secondary-side power devices in a wide load range to reduce the switching losses due to the secondary-side phase-shift control scheme. Furthermore, compared with the conventional phase-shift control mechanism, the circulating current at the freewheeling stage is effectively suppressed as well to minimize the conduction losses. Moreover, the voltage stress of the primary switches is only half of the input voltage by employing the improved three-level structure, which makes the low-voltage rated power devices available to improve the circuit performance. In addition, the converter can work in the buck, balance, and boost modes to achieve a relatively wide input voltage range, which is an expected advantage for the communication power system to minimize the electrolytic capacitors with an acceptable hold-up time. The operation principle is analyzed and experimental results of a 1-kW 100-kHz prototype are provided to verify the effectiveness and the advantages of the proposed converter. [ABSTRACT FROM AUTHOR]

A three-port dc–dc converter integrating photovoltaic (PV) and battery power for high step-up applications is proposed in this paper. The topology includes five power switches, two coupled inductors, and two active-clamp circuits. The coupled inductors are used to achieve high step-up voltage gain and to reduce the voltage stress of input side switches. Two sets of active-clamp circuits are used to recycle the energy stored in the leakage inductors and to improve the system efficiency. The operation mode does not need to be changed when a transition between charging and discharging occurs. Moreover, tracking maximum power point of the PV source and regulating the output voltage can be operated simultaneously during charging/discharging transitions. As long as the sun irradiation level is not too low, the maximum power point tracking (MPPT) algorithm will be disabled only when the battery charging voltage is too high. Therefore, the control scheme of the proposed converter provides maximum utilization of PV power most of the time. As a result, the proposed converter has merits of high boosting level, reduced number of devices, and simple control strategy. Experimental results of a 200-W laboratory prototype are presented to verify the performance of the proposed three-port converter. [ABSTRACT FROM AUTHOR]

This paper presents three topological classes of dc-to-dc converters, totaling nine converters (each class with three buck, boost, and buck-boost voltage transfer function topologies), which offer continuous input and output energy flow, applicable and mandatory for renewable energy source, maximum power point tracking and maximum source energy extraction. A current sourcing output caters for converter module output parallel connection. The first class of three topologies employs both series input and output inductance, while anomalously the other two classes of six related topologies employ only either series input (three topologies) or series output (three topologies) inductance. All nine converter topologies employ the same elements, while additional load shunting capacitance creates a voltage sourcing output. Converter time-domain simulations and experimental results for the converters support and extol the concepts and analysis presented. [ABSTRACT FROM AUTHOR]

With the rapid growth of battery-powered portable electronics, an efficient power management solution is necessary for extending battery life. Generally, basic switching regulators, such as buck and boost converters, may not be capable of using the entire battery output voltage range (e.g., 2.5–4.7 V for Li-ion batteries) to provide a fixed output voltage (e.g., 3.3 V). In this paper, an average-current-mode noninverting buck–boost dc–dc converter is proposed. It is not only able to use the full output voltage range of a Li-ion battery, but it also features high power efficiency and excellent noise immunity. The die area of this chip is 2.14 × 1.92mm^2, fabricated by using TSMC 0.35 μm 2P4M 3.3 V/5 V mixed-signal polycide process. The input voltage of the converter may range from 2.3 to 5 V with its output voltage set to 3.3 V, and its switching frequency is 500 kHz. Moreover, it can provide up to 400-mA load current, and the maximal measured efficiency is 92.01%. [ABSTRACT FROM PUBLISHER]

Plug-in hybrid electric vehicles (PHEVs) will play a vital role in future sustainable transportation systems due to their potential in terms of energy security, decreased environmental impact, improved fuel economy, and better performance. Moreover, new regulations have been established to improve the collective gas mileage, cut greenhouse gas emissions, and reduce dependence on foreign oil. This paper primarily focuses on two major thrust areas of PHEVs. First, it introduces a grid-friendly bidirectional alternating current/direct current ac/dc–dc/ac rectifier/inverter for facilitating vehicle-to-grid (V2G) integration of PHEVs. Second, it presents an integrated bidirectional noninverted buck–boost converter that interfaces the energy storage device of the PHEV to the dc link in both grid-connected and driving modes. The proposed bidirectional converter has minimal grid-level disruptions in terms of power factor and total harmonic distortion, with less switching noise. The integrated bidirectional dc/dc converter assists the grid interface converter to track the charge/discharge power of the PHEV battery. In addition, while driving, the dc/dc converter provides a regulated dc link voltage to the motor drive and captures the braking energy during regenerative braking. [ABSTRACT FROM PUBLISHER]

Multiport dc/dc converters are widely employed in hybrid energy generation systems to provide stable power to key loads with high power density. In this paper, the switch duty cycle and the phase angle of the interleaved converters are employed as two control freedoms to achieve decoupled voltage regulation within a certain operating range among different ports, which is referred to as pulsewidth modulation plus phase angle shift (PPAS) control scheme. An interleaved bidirectional buck-boost converter and a full-bridge converter are integrated together to derive a combined three-port dc/dc converter for photovoltaic (PV)-battery hybrid energy systems, which is adopted as a typical example to explore the clear performance of the proposed PPAS control strategy. The bidirectional buck-boost converter and the full-bridge converter share the same power MOSFETs in the primary side, which simplifies the circuit structure and improves the power density. The duty cycle of the interleaved bidirectional buck-boost converter is adopted to realize the maximum power point tracking and the voltage balance between the battery and the PV cell in the primary side. Furthermore, the phase angle of the interleaved buck-boost converter is employed as another control freedom to achieve accurate secondary output voltage regulation. Finally, a 100-W PV-Battery energy system is designed and tested to verify the effectiveness of the proposed scheme. [ABSTRACT FROM AUTHOR]

This paper presents a resonant single-ended-primary-inductor-converter (SEPIC) converter and control method suitable for high frequency (HF) and very high frequency (VHF) dc-dc power conversion. The proposed design provides high efficiency over a wide input and output voltage range, up-and-down voltage conversion, small size, and excellent transient performance. In addition, a resonant gate drive scheme is presented that provides rapid startup and low-loss at HF and VHF frequencies. The converter regulates the output using an ON-OFF control scheme modulating at a fixed frequency (170 kHz). This control method enables fast transient response and efficient light-load operation while providing controlled spectral characteristics of the input and output waveforms. A hysteretic override technique is also introduced which enables the converter to reject load disturbances with a bandwidth much greater than the modulation frequency, limiting output voltage disturbances to within a fixed value. An experimental prototype has been built and evaluated. The prototype converter, built with two commercial vertical MOSFETs, operates at a fixed switching frequency of 20 MHz, with an input voltage range of 3.6-7.2 V, an output voltage range of 3-9 V, and an output power rating of up to 3 W. The converter achieves higher than 80% efficiency across the entire input voltage range at nominal output voltage and maintains good efficiency across the whole operating range. [ABSTRACT FROM AUTHOR]

This paper proposes a new high step-up dc–dc converter designed especially for regulating the dc interface between various microsources and a dc–ac inverter to electricity grid. The figuration of the proposed converter is a quadratic boost converter with the coupled inductor in the second boost converter. The converter achieves high step-up voltage gain with appropriate duty ratio and low voltage stress on the power switch. Additionally, the energy stored in the leakage inductor of the coupled inductor can be recycled to the output capacitor. The operating principles and steady-state analyses of continuous-conduction mode and boundary-conduction mode are discussed in detail. To verify the performance of the proposed converter, a 280-W prototype sample is implemented with an input voltage range of 20–40 V and an output voltage of up to 400 V. The upmost efficiency of 93.3% is reached with high-line input; on the other hand, the full-load efficiency remains at 89.3% during low-line input. [ABSTRACT FROM AUTHOR]