Search

Generally, single-stage buck–boost inverters consist of distinct circuits operating individually in buck/boost or positive/negative modes, the latter definitely leading to crossover distortion in the output current. This paper proposes a switching strategy that changes the bimodal operation of a single-stage buck–boost topology to a single-mode inverter. This is due to the consequent voltage gain that ensures that the output voltage polarity, apart from its magnitude, is an exclusive function of the duty ratio. Operational principle and salient hardware design are explained with the help of equivalent circuits. Details about the dynamic model are presented, based on which controller design is carried out for both stand-alone and grid-connected operation. Experimental results obtained from a 300-W, 110-V laboratory prototype are presented to validate the performance of the proposed switching strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A new space vector modulation, i.e., ZSVM3, for three-phase quasi-Z-source rectifier (qZSR) is proposed. All switches in the three-phase bridge can be turned on and turned off with zero current or zero voltage using the proposed ZSVM3 with no auxiliary circuit. The current through the inductors of the quasi-Z-source network operates in a boundary conduction mode or discontinuous conduction mode to achieve all freewheeling diodes turned off with zero-current switching (ZCS). At the same time, the switch in the quasi-Z-source network can be turned on with ZCS. Besides, the voltage stress of all switches is equal to dc-link voltage. The operation principle of the qZSR is analyzed in detail, and the calculated value of the quasi-Z-source inductor is given. The proposed theory in this paper is verified by a 2-kW prototype. [ABSTRACT FROM PUBLISHER]

In this paper, two switched-capacitor quasi-switched boost inverters (qSBIs) are proposed. By adding one capacitor and one diode to the qSBIs, the proposed inverters achieve high voltage gain with low voltage stress on active switches, capacitors, and diodes. The proposed inverters can extend to n-cell for voltage gain improvement. The operating principle, steady-state analysis, and impedance parameter selections of the proposed inverter are presented. A full comparison between the proposed inverter and other impedance-source inverters is addressed. A 500-W prototype is built to verify the operating theory of the proposed inverter in both the standalone mode and the grid-connected mode. Simulation and experimental results validate the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a new high-gain soft-switching dc–dc topology based on a switched inductor boost converter (SIBC). A conventional SIBC as a high gain boost topology has the issues of high conduction loss in switching diodes and high switching loss in the main switches. Also, it has severe electromagnetic interference (EMI) issue due to high-frequency ringing formed by parasitic inductance and diode junction capacitors. The new topology is derived with the objective of achieving zero voltage switching (ZVS) turn on of the main switch. Instead of adding extra active clamp zero voltage transition (ZVT) path at the switching node, the proposed topology augments the auxiliary ZVT path to the switching diode path. This is achieved by replacing the switching diodes with synchronous switches. The new topology can achieve soft switching for all the switches and alleviate the EMI issue. All the diodes achieve zero current switching (ZCS) turn off without reverse recovery. Auxiliary switches have ZCS turn on and ZVS turn off, and the main switches have ZVS turn on. The soft-switching SIBC also reduces the conduction loss in the switching diodes. A numerical simulation in PLECS and a prototype hardware are built corresponding to a micro-inverter application with 100 kHz switching frequency. Peak power conversion efficiency of 94.76% is achieved in the hardware prototype with Si devices. [ABSTRACT FROM PUBLISHER]

This paper proposes an interleaved hybrid converter (IHC) with simultaneous dc and ac outputs for dc microgrid applications. The IHC is realized by interleaving two conventional boost converters and replacing the active switch of lower boost converter by an H-bridge voltage source inverter. This arrangement enables the proposed IHC to operate at the condition where the sum of duty ratio (\boldsymbolD ) and modulation index (\boldsymbolM ) can be more than or equal to one, i.e., \boldsymbolD + \boldsymbolM \geq 1, unlike the conventional hybrid converters. The proposed IHC is capable of giving dc with high voltage gain and improved ac with reduced harmonic distortion. Due to interleaving nature of the IHC, input current is shared between the power converters and thus enables the use of low current rated switching devices and lower values of inductors. This results in reduced power losses and increased efficiency as compared to the conventional hybrid converters. The IHC also has inherent shoot-through protection capability, better electromagnetic interference immunity, and reliability. A modified unipolar sinusoidal pulse width modulation technique is used to control the power flow of the IHC. Detailed mathematical modeling of the proposed IHC is carried out and its steady-state behavior is validated through experimental results on a 500 W laboratory prototype. [ABSTRACT FROM PUBLISHER]

A single-switch quadratic buck–boost converter with continuous input port current and continuous output port current is proposed in this paper. Compared with the traditional buck-boost converter, the proposed converter can obtain a wider range of the voltage conversion ratio with the same duty cycle. Moreover, the proposed converter can operate with continuous input port current and continuous output port current compared to the existing counterparts with inherently discontinuous input port current and discontinuous output port current. The operating principle and steady-state performance of the proposed converter under continuous inductor current mode is analyzed in detail. Then, the comparison between the proposed converter and the existing quadratic buck–boost converters has been conducted to demonstrate the unique features of the proposed one. Finally, experimental results from a prototype built in the lab are recorded to verify the effectiveness and validity of the proposed quadratic buck–boost converter. [ABSTRACT FROM PUBLISHER]

This paper introduces series work of common-mode (CM) voltage reduction for the paralleled inverters. The paralleled inverters’ phase-legs are connected through coupling inductors and the combined three-phase currents are provided to the load. Interleaving is an approach to reduce the CM voltage for the paralleled inverters but it cannot eliminate CM voltage. A novel pulse-width-modulation (PWM) method for paralleled inverters which can theoretically achieve zero CM voltage is developed. Considering the basic voltage vectors in each inverter, novel paralleled voltage vectors which have zero CM voltage are proposed to combine the reference voltage vector. The action time's distribution and voltage vectors’ sending sequence for each inverter are also introduced. The proposed PWM method can make sure the voltage of the two inverters are balanced in each switching cycle and limits the circulating current through small coupling inductors. Similar to interleaving space vector PWM, the proposed zero CM PWM also has the ability to reduce the output current ripple and electromagnetic interference (EMI). Simulation and experimental results are provided to show the advantage of paralleled inverters in CM voltage reduction and validate the proposed method has good performance to reduce CM current and CM EMI noise. [ABSTRACT FROM PUBLISHER]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

A dual-buck inverter (DBI) possesses no shoot-through worries and can boost efficiency by using power mosfet s. The main drawback of a DBI is the use of more inductors than in a traditional full-bridge inverter. This greater number of inductors decreases the power density and increases system cost. In this paper, a modified cascaded full-bridge DBI is proposed. It retains all the advantages of the conventional cascaded full-bridge DBI, possesses no shoot-through issues, and can be operated with no pulse-width-modulation dead-times. It can be implemented with power mosfet without reverse recovery issues of a body diode to boost efficiency. The cascaded modules in the proposed inverter share current limiting inductors. Therefore, the number of inductors and inductor footprints, the complexity of the circuit layout, required inductance, and magnetic volume can all be decreased. To show the advantages of the proposed inverter, detailed theoretical analysis and experimental results are provided. [ABSTRACT FROM PUBLISHER]

In this paper, an improved transformerless single-phase single-stage grid-tied flying inductor inverter is presented. The negative terminal of the photovoltaic (PV) array is grounded in the improved topology, which increases reliability and suppresses the leakage current. The proposed topology has buck–boost capability without increasing the number of required components and has a high efficiency. An improved control algorithm for proper operation of the proposed topology which decreases switching losses has been investigated. Moreover, a perturbation and observation maximum power point tracking (MPPT) algorithm has been adapted to the proposed inverter, which does not utilize proportional–integral (PI) controllers, for the purpose of the MPPT. Furthermore, a design procedure of the passive elements of the converter based on the corresponding operating has been demonstrated. Simulation in MATLAB Simulink plus an experimental prototype is developed to reconfirm the designed results. Finally, a comparison study has been investigated for better clarification of the advantages and disadvantages of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a dc to ac converter with the ability of voltage increasing is presented. This inverter is designed in a way that just one dc source is used. Also, by using power storage technique and with combining charged capacitors and dc source in series form, output voltage levels can be increased. This inverter is in a modular structure and has the ability of capacitor's voltage self-balancing. H-bridge inverter was not used at the end of the proposed converter and all elements tolerate a voltage stress equal to the amount of input dc source. This leads to remarkable decrease of total standing voltage and peak inverse voltage. Other advantage of the proposed inverter is its potentiality of performance in high-frequency applications. The modular form of the proposed inverter provides the potentiality of extension to higher voltage levels and eases the maintenance. Moreover, considering to the fact that the stress of all components of the suggested inverter is equal to the input source, the performance in high voltage is added to the characteristics of the proposed inverter. The nine-level structure of the proposed inverter is simulated and laboratory test is carried out for the verification of its performance. [ABSTRACT FROM PUBLISHER]

High-efficiency and compact single-phase inverters are desirable in many applications such as solar energy harvesting and electric vehicle chargers. This paper presents a 2-kW, 60-Hz, 450-V \text{DC}-to-240-V \text{AC} power inverter, designed and tested subject to the specifications of the Google/IEEE Little Box Challenge. The inverter features a seven-level flying capacitor multilevel converter, with low-voltage GaN switches operating at 120 kHz. The inverter also includes an active buffer for twice-line-frequency power pulsation decoupling, which reduces the required capacitance by a factor of 8 compared to conventional passive decoupling capacitors, while maintaining an efficiency above 99%. The inverter prototype is a self-contained box that achieves a high power density of 216 W/in $^3$ and a peak overall efficiency of 97.6%, while meeting the constraints including input current ripple, load transient, thermal, and FCC Class B EMC specifications. [ABSTRACT FROM AUTHOR]

This paper proposes a single-stage light-emitting diode (LED) driver based on an inverted buck topology, using current path control switches. The proposed circuit consists of a control circuit, a bridge diode, and an inverted buck converter with multiple switches connected to the LED segments in parallel. Whereas the typical buck LED driver operates with a fixed LED forward voltage, the proposed driver operates with a variable LED forward voltage, according to the input voltage level. Because of this capability to adjust the LED forward voltage, it can reduce the current ripple and the switching frequency with a small inductance value. In addition, it enables operation with LED lamps of a wide voltage range, while simultaneously achieving small dead-angles. The detailed operation principles are described, and the design considerations for the proposed driver are discussed. The proposed driver circuit and control operation are verified experimentally using a 7 W hardware prototype with four LED segments. The obtained experimental results show that under a 110 Vrms input voltage, the proposed driver achieves a power factor of 0.94 with a small dead-angle and an efficiency of 94%. [ABSTRACT FROM PUBLISHER]

To solve the problem of the mismatched voltage levels between the dynamic lower voltage of the fuel cell stack and the required constant higher voltage (400 V) of the dc-link bus of the inverter for fuel cell vehicles, a boost three-level dc–dc converter with a diode rectification quasi-Z source (BTL-DRqZ) is presented in this paper, based on the conventional flying-capacitor boost three-level dc–dc converter. The operating principle of a wide range voltage-gain for this topology is discussed according to the effective switching states of the converter and the multiloop energy communication characteristic of the DRqZ source. The relationship between the quasi-Z source net capacitor voltages, the modulation index, and the output voltage is deduced and then the static and dynamic self-balance principle of the flying-capacitor voltage is presented. Furthermore, a boost three-level dc–dc converter with a synchronous rectification quasi-Z source (BTL-SRqZ) is additionally proposed to improve the conversion efficiency. Finally, a scale-down 1.2 kW BTL-SRqZ prototype has been created, and the maximum efficiency is improved up to 95.66% by using synchronous rectification. The experimental results validate the feasibility of the proposed topology and the correctness of its operating principles. It is suitable for the fuel cell vehicles. [ABSTRACT FROM PUBLISHER]

Photovoltaic (PV) microinverters dispense with the line frequency transformer, however at the cost of system grounding and ground leakage current problems. These have been erstwhile resolved by the topologies derived from buck, boost, buck–boost, Zeta, Watkins–Johnson, and Ćuk converters, or combinations of these. The Ćuk derived inverters, employing second-order input and output filters, offer the most efficient, lightweight, and economical solution in the class. This paper presents design and detailed operation of a Ćuk derived, common-ground PV microinverter in continuous conduction mode operation. The inverter is shown to be compatible with both linear and nonlinear loads, in stand-alone and grid-connected modes of operation. Optimal design rules of passive components are rigorously derived to ensure attenuation of input voltage ripples arising from the twin effects of switching and double-frequency output power oscillation. Additionally, the design rules also incorporate considerations of efficiency maximization and some aspects of easing control complexity. Inverter performance is experimentally validated with a 300 VA, 110 V, and 50/60 Hz laboratory prototype. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes a soft switching technique for dc/ac inverters, by using duty cycle and frequency modulation. Zero voltage switching (ZVS) is achieved through controlling the inductor current bidirectional in every switching cycle. This technique requires no additional resonant components and can be employed for various low power applications on conventional full-bridge and half-bridge inverter topologies. Three different current mode control schemes are derived from the basic theory of the proposed technique. They are referred to as boundary current mode (BCM), variable hysteresis current mode (VHCM), and constant hysteresis current mode (CHCM) in this paper and their advantages and disadvantages are compared. Simulation and experimental results demonstrate the feasibilities of the proposed soft-switching technique and its control schemes. [ABSTRACT FROM PUBLISHER]

Switched boost inverter (SBI) is a single-stage power converter derived from Inverse Watkins Johnson topology. Unlike the traditional buck-type voltage source inverter (VSI), the SBI can produce an ac output voltage that is either greater or less than the available dc input voltage. Also, the SBI exhibits better electromagnetic interference noise immunity when compared to the VSI, which enables compact design of the power converter. Another advantage of SBI is that it can supply both dc and ac loads simultaneously from a single dc input. These features make the SBI suitable for dc nanogrid applications. In this paper, the SBI is proposed as a power electronic interface in dc nanogrid. The structure and advantages of the proposed SBI-based nanogrid are discussed in detail. This paper also presents a dq synchronous-reference-frame-based controller for SBI, which regulates both dc and ac bus voltages of the nanogrid to their respective reference values under steady state as well as under dynamic load variation in the nanogrid. The control system of SBI has been experimentally validated using a 0.5-kW laboratory prototype of the SBI supplying both dc and ac loads simultaneously, and the relevant experimental results are given in this paper. The low cross regulation and the dynamic performance of the control system have also been verified experimentally for a 20% step change in either dc or ac load of SBI. These experimental results confirm the suitability of the SBI and its closed-loop control strategy for dc nanogrid applications. [ABSTRACT FROM AUTHOR]

This paper focuses on the common dc-link voltage between a three-phase diode rectifier and a modular multilevel cascade inverter based on double-star chopper cells (MMCI-DSCC) for a medium-voltage motor drive. This motor drive can be operated even when no capacitor exists on the dc link. However, a nonnegligible, but predictable, amount of switching-ripple voltage occurs on the dc link. This paper achieves modeling and analysis of the switching-ripple voltage, thus making it possible to design a small-sized dc passive filter consisting of series connection of a film capacitor and a damping resistor. A 400-V, 15-kW down scaled system is used to confirm the effectiveness of the analysis and the dc filter. Experimental results show that the switching-ripple voltage can be attenuated satisfactorily by the dc filter, and that the power loss dissipated in the damping resistor is negligible, compared to the rated power of 15 kW. [ABSTRACT FROM AUTHOR]

This paper presents a direct model predictive current control (MPC) strategy for quasi-Z-source inverters (qZSIs). A discrete-time model is derived that accurately captures all operating modes of the converter. Both sides of the qZSI are controlled simultaneously based on the inductor current and capacitor voltage on the dc side as well as the output current on the ac side. To improve the closed-loop performance of the converter, a long prediction horizon is implemented. However, the underlying optimization problem may become computationally intractable because of the substantial increase in the computational power demands, which in turn would prevent the implementation of the control strategy in real time. To overcome this and to solve the problem in a computationally efficient manner, a branch-and-bound strategy is used along with a move blocking scheme. Simulation and experimental results are provided to verify the effectiveness of the presented control strategy. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase switched-coupled-inductor dc–ac inverter featuring higher voltage gain than the existing single-phase qZ-source and semi-Z-source inverters. Similar to the single-phase qZ-source and semi-Z-source inverters, the proposed inverter also has common grounds between the dc input and ac output voltages, which is beneficial especially for photovoltaic inverter systems. The inverter volume and maximum current flowing can be reduced significantly through the coupling of all inductors. A theoretical analysis of the proposed inverter is described and a 280-W experimental prototype is built to verify the performance of the inverter. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase, single-stage buck–boost inverter for photovoltaic (PV) systems. The presented topology has one common terminal in input and output ports which eliminates common mode leakage current problem in the grid-connected PV applications. Although it uses four switches, its operation is bimodal and only two switches receive high-frequency pulse width modulation signals in each mode. Its principle of operation is described in detail with the help of equivalent circuits. Its dynamic model is presented, based on which a bimodal controller is designed. Experimental results, in stand-alone and grid-connected mode, obtained with a 300-W laboratory prototype are presented to validate its performance. [ABSTRACT FROM AUTHOR]

A nonlinear pulse width modulation-controlled single-phase boost mode photovoltaic grid-connected inverter with limited storage inductance current is proposed in this paper. The circuit topology, control strategy, steady-state principle characteristic, and design criterion for the key circuit parameters of this kind of inverter are investigated in depth, and important conclusions are obtained. The inverter's regenerating energy duty ratio 1–D which decreases with the decline of the grid-connected voltage is real time adapted by sampling and feeding back the inverting bridge modulation current, and the average value of the modulation current in each switching cycle tracks the reference sinusoidal signal to get high-quality grid-connected current. The active control of the energy storage inductance current and the balance of the voltage step-up ratio are realized by adding a bypass switch connected in parallel with the energy storage inductance and using two kinds of switching pattern namely boost pattern and freewheeling pattern. The theoretical analysis and experimental results of the 1 kVA 110 VDC/220 V50 Hz photovoltaic grid-connected inverter prototype show that it has the advantages such as single-stage boost conversion, high conversion efficiency, high quality of grid-connected current waveform, low value of energy storage inductance, simple control, etc. [ABSTRACT FROM AUTHOR]

The quasi-Z-source inverter (qZSI) has attracted much attention for motor drives and renewable energy applications due to its capability to boost or buck in a single converter stage. However, this capability is associated with different challenges related to the closed-loop control of currents, control the dc capacitor voltage, produce three-phase ac output current with high dynamic performance, and obtain continuous and low ripple input current. This paper presents a predictive control strategy for a three-phase qZSI that fulfills these requirements without adding any additional layers of control loops. The proposed controller implements a discrete-time model of the qZSI to predict the future behavior of the circuit variables for each switching state, along with a set of multiobjective control variables all in one cost function. The quasi-impedance network and the ac load are considered together when designing the controller in order to obtain stability of the impedance network with a step change in the output reference. A detailed comparative investigation between the proposed controller and the conventional proportional-integral (PI) controller is presented to prove the superiority of the proposed method over the conventional control method. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

In a zero-voltage switching (ZVS) inverter, high conversion efficiency and miniaturization are expected since switching loss can be dramatically reduced with proper design. In order to realize ZVS condition, auxiliary components such as inductors, capacitors, and switches are embedded in the inverter to implement the function. Since the design of auxiliary components is critical to the ZVS inverter, it is impossible to realize maximum efficiency or minimum size by following the conventional design procedure. This paper introduces an optimized design methodology for a three-phase ZVS inverter with objectives of both high efficiency and miniaturization. Based on the loss models of different commercial IGBT modules under different ZVS conditions, as well as the loss models of auxiliary components and filter inductors, the issue of pursuing highest efficiency and power density is transformed into solving a constrained nonlinear multivariable problem. According to the proposed design methodology, all parameters that influence the efficiency and physical dimensions are considered simultaneously. Thus, the optimized selection of the IGBT module, the parameters of the auxiliary components and the filter inductors would be obtained. A 30-kW three-phase ZVS inverter prototype is built to verify the proposed design method. With proposed design method, the improved prototype has achieved both smaller passive components volume and higher efficiency compared to the former prototype. [ABSTRACT FROM AUTHOR]

The five-phase coupled-inductor inverter is a newly proposed option for three-level five-phase inverter drives. This paper comprehensively analyzes the inverter including the coupled-inductor current, current stress on the dc-link capacitors, and a comparison of these performance aspects using three pulse width modulation (PWM) strategies. Mathematical derivations of the inverter currents and the associated current stress reveal that the current stress is not only influenced by the choice of modulation strategy, as in the neutral-point-clamped topology, but also by the value of coupled inductance; furthermore, the choice of the modulation strategy impacts the core loss of the coupled inductors. Three carrier-based PWM methods are considered: sinusoidal PWM (SPWM), and two methods with the common-mode voltage reduction (referred to as CMVR1 and CMVR2) for the five-phase coupled-inductor inverter. CMVR2 is shown to be the best solution if common-mode voltage reduction is required. The analysis demonstrates that SPWM performs better with respect to current stress and inverter losses, therefore is the preferable modulating strategy for the five-phase coupled-inductor inverter if common-mode voltage reduction is not required. The analysis is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper introduces a combination of two proposed efficiency improvement techniques for a microinverter with current mode control zero-voltage switching output stages. The first technique is dynamic dead-time optimization wherein pulse width modulation dead times are dynamically adjusted as a function of load current. The second method is advanced phase skipping control which maximizes inverter efficiency by controlling power on individual phases depending on the available input power from the photovoltaic source. Neither of the techniques requires any additional circuit components and both can be easily implemented in digital controller firmware. The two techniques were designed and implemented in a 400-W three-phase microinverter prototype. The experimental results validate the theoretical analysis of these techniques and demonstrate that a significant efficiency improvement can be achieved by combining the two proposed control techniques. [ABSTRACT FROM AUTHOR]

This paper identifies the characteristics of a current source inverter operating in discontinuous conduction mode, and proposes a new multiobjective pulse-width modulation (PWM) method to mitigate voltage boosting and harmonic distortion effects. The method takes into account load impedance effects. Controls are also developed to enable transition between the multiobjective PWM method and conventional PWM as the current source inverter operates in discontinuous and continuous modes of operation. The concept is verified experimentally on a 3 kW test bed. [ABSTRACT FROM AUTHOR]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

Voltage source inverter cannot provide an output voltage higher than its input and needs a dead-time scheme for its switches to prevent dc-link short circuit due to spurious turn-on of switches by electromagnetic interference (EMI). Impedance source inverters have eliminated these disadvantages by providing boost functionality with improved EMI immunity. Coupled inductor-based impedance source inverters provided increased gain at the expense of increased coupled inductor turns-ratio. In this paper, a coupled inductor based high gain inverter is proposed, which achieves higher gain by increasing the coupled inductor turns-ratio (n = n2/n1) within a very narrow turns-ratio range of $0 \leq n < 1$, which is a major improvement over the other coupled inductor based high boost impedance source inverters. The proposed inverter, named Improved Trans–Current–Fed Switched Inverter, is described along with its equivalent operating states and relation between its input and output variables are derived. The steady-state inverter waveforms are shown using PSpice simulations. The operation of the inverter is validated by the experimental results, which show strong correlation with the theoretical analysis. A 110-V RMS ac output is obtained from 26-V dc input using a coupled inductor with turns-ratio of 0.33 to demonstrate its high-boost operation. [ABSTRACT FROM PUBLISHER]

This paper describes novel single-phase solutions with increased inverter voltage levels derived by means of a nonstandard inverter configuration and impedance source networks. Operation principles based on special modulation techniques are presented. Detailed component design guidelines along with simulation and experimental verification are also provided. Possible application fields are discussed, as well as advantages and disadvantages. Finally, future studies are addressed for the new solutions. [ABSTRACT FROM PUBLISHER]

Electronic ballasts are implemented for obtaining a high power factor and a good operation of the lamp; these goals are reached traditionally by implementing multiple stages. On the first stage, a unity power factor is obtained and the second stage is designed in order to feed properly the lamp. Different topologies have been studied not only for decreasing the number of employed controllers and stages, but also reducing the number of components and active switches. Electronic ballasts, which are based on the “Z” and “qZ” source inverters, are considered in this paper, where the proposed systems have a single stage. Two topologies are illustrated: the first one for the fluorescent lamps and the second one for the high intensity discharge lamps, where electronic ballasts with a high power factor are obtained. The operation, analysis, and experimental results are shown. [ABSTRACT FROM PUBLISHER]

Since its conception, the quasi-Z-source inverter (qZSI) has been extensively studied, especially in renewable energy applications fields due to its ability to withstand shoot-through and provide continuous current. However, research thus far has only explored symmetric qZSI/ZSI impedance network with large inductances and capacitances. By utilizing next-gen wideband-gap devices at high-switching frequency, the impedance network can be significantly reduced. However, the reduced qZS impedance network will result in abnormal operation modes, in addition to frequency resonances, in several kilohertz range. Thus, this paper first thoroughly explains the occurrence of the abnormal states, analyzes the effects of the abnormal states on the frequency resonance, and then proposes a control method to suppress the resonance that result from the reduced impedance network. A 1-kW prototype is built and experimental results verify the effectiveness of the analysis and proposed control method. [ABSTRACT FROM PUBLISHER]

A single-phase inverting buck–boost ac–ac converter is proposed in this paper. The proposed converter has no shoot-through and dead-time problems and, like conventional dc–dc converters, it can be operated with simple pulse width modulation (PWM) control. It offers high frequency and high efficiency operation because high speed mosfet can be used as switching device without the reverse recovery issues and losses of its body diode. The proposed converter features quasi-continuous input and output currents, high input power factor, low total harmonic distortion of input and output currents, and high efficiency. A 460 W laboratory prototype was constructed and tested with interleaved and complementary PWM controls using a resistive and inductive load. Detailed experimental results are provided to show the novelty of the proposed converter. Experimental results confirmed that the proposed converter can obtain 93.8% efficiency at 60 kHz switching frequency. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase grid-connected transformerless photovoltaic inverter for residential application is presented. The inverter is derived from a boost cascaded with a buck converter along with a line frequency unfolding circuit. Due to its novel operating modes, high efficiency can be achieved because there is only one switch operating at high frequency at a time, and the converter allows the use of power MOSFET and ultrafast reverse recovery diode. It also features a robust structure because the phase leg does not have a shoot-through issue. This paper begins with theoretical analysis and modeling of this boost-buck converter-based inverter. And the model indicates that small boost inductance will lead to an increase in the resonant pole frequency and a decrease in the peak of Q, which results in easier control and greater stability. Thus, interleaved multiple phases structure is proposed to have small equivalent inductance; meanwhile, the ripple can be decreased, and the inductor size can be reduced as well. A two-phase interleaved inverter is then designed accordingly. Finally, the simulation and experiment results are shown to verify the concept and the tested efficiency under 1-kW power condition is up to 98.5%. [ABSTRACT FROM AUTHOR]

This paper deals with a new family of high boost voltage inverters called switched-inductor quasi-Z-source inverters (SL-qZSIs). The proposed SL-qZSI is based on the well-known qZSI topology and adds only one inductor and three diodes. In comparison to the SL-ZSI, for the same input and output voltages, the proposed SL-qZSI provides continuous input current, a common ground with the dc source, reduced the passive component count, reduced voltage stress on capacitors, lower shoot-through current, and lower current stress on inductors and diodes. In addition, the proposed SL-qZSI can suppress inrush current at startup, which might destroy the devices. This paper presents the operating principles, analysis, and simulation results, and compares them with those of the SL-ZSI. To verify the performance of the proposed converter, a laboratory prototype was constructed with 48 Vdc input and an ac output line-to-line voltage of 120 Vrms. The simulation and experimental results verified that the converter has high step-up inversion ability. [ABSTRACT FROM AUTHOR]

A family of isolated buck–boost dc/dc converter for wide input-voltage range is proposed in this paper, and the full-bridge (FB) boost converter, being one of the typical topologies, is analyzed. Due to the existence of the resonant inductor (including the leakage inductor), the FB-boost converter can only adopt the two-edge-modulation (TEM) scheme with the FB cell being leading-edge modulated and the boost cell being trailing-edge modulated to minimize the inductor current ripple over the input-voltage range, and a phase-shift-control-scheme-based TEM with the use of the market available controller IC such as UC3895 is proposed, which realizes phase-shifted control for the FB cell to achieve zero-voltage switching. In order to improve the reliability and efficiency of the FB-boost converter, a three-mode dual-frequency control scheme is proposed, in which the FB-boost converter operates in boost, FB-boost and FB modes in low, medium and high input voltage regions, respectively, and for which the expression of the inductor current ripple is derived in this paper. As the input voltage in the FB-boost mode is close to the output voltage, the inductor current ripple in this mode is much smaller than that in the other modes, and the switching frequency of the boost cell in this mode can be lowered to one-(2N+1)th of the preset switching frequency to reduce the switching loss, and hence, to improve the efficiency. A 250–500 V input, 360 V output, and 6 kW rated power prototype is fabricated to verify the effectiveness of the design and control method. The average efficiency over the input-voltage range is 96.5%, and the highest efficiency attained is 97.2%. [ABSTRACT FROM AUTHOR]

In many modern energy conversion systems, a dc voltage, which is provided from a sustainable energy source or energy storage device, must be boosted and converted to an ac voltage with a fixed amplitude and frequency. In this paper, a switching pattern based on the concept of the conventional space-vector pulsewidth-modulated (SVPWM) technique is developed for single-stage, three-phase boost-inverters using the topology of current-source inverters. The six main switching states, and two zeros, with three switches conducting at any given instant in conventional SVPWM techniques are modified herein into three-charging states and six discharging states with only two switches conducting at any given instant. The charging states are necessary in order to boost the dc input voltage. The developed switching pattern was experimentally verified through a laboratory-scaled three-phase 500-W boost inverter and the results are presented in this paper. [ABSTRACT FROM AUTHOR]

The conventional current-source inverter has two major problems: unidirectional power flow and voltage boost operation, which make it impossible to be used in many applications, such as hybrid electric vehicles and general-purpose variable-speed motor drives. Z-source inverters (ZSIs) can solve both problems. Quasi-ZSIs (qZSIs) were recently proposed as an important improvement to traditional ZSIs. Besides the advantages inherited from ZSIs, qZSIs also have several of their own merits. This paper presents a comprehensive study on the new features of current-fed qZSI, including the advantageous buck–boost function, improved reliability, reduced passive component ratings, and unique regeneration capability. The current-fed qZSIs are bidirectional with an additional diode, unlike the voltage-fed ZSI that needs a switch to achieve bidirectional power flow. A modified space vector pulse-width-modulation method is proposed, and the available operating regions for motoring and regeneration operation are analyzed in this paper. Since the current-fed qZSI has the same operation as the current-fed ZSI, many results of this paper are also applicable to the current-fed ZSI. A reverse-blocking insulated-gate bipolar-transistor-based current-fed qZSI prototype was developed in the laboratory. Simulation and experimental results are shown to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper presents design and implementation of a 5-kW single-phase bidirectional inverter with wide inductance variation. For dc-microgrid applications, the bidirectional inverter has to fulfill grid connection and rectification with power factor correction to regulate the dc bus to a certain range of voltages. In the inverter operation, inductor current can vary from 0 to 32 A in one line cycle. This will result in wide inductance variation, around seven times for an inductor constructed with a molybdenum permalloy powder core, and thus, high current ripple and fluctuation. In this paper, we take into account this variation while designing controller and selecting key components to ensure inverter normal operation. Additionally, to adopt a cost-effective microcontroller for the inverter, the sensitivities of the control to various parameters are investigated and presented in this paper. Experimental results measured from a 5-kW single-phase prototype have verified the feasibility of the designed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

For a grid-tied three-level neural-point-clamped (NPC) inverter, fully digital hysteresis controller with simple variable hysteresis band is insufficient to stabilize switching frequency (fs). The challenge mainly comes from the restriction of analogue-to-digital converter (ADC) sampling frequency, which leads to inaccurate current-boundary-touching capture. As a result, fs jitter appears. This phenomena becomes much more serious around grid voltage zero-crossing points due to zero-approaching hysteresis band, where obvious fs variation happens. To stabilize fs in a fully digital manner, two techniques are proposed in this paper: the mixed-level scheme and the prediction-based sampling method. The former one is used to cope with the obvious fs variation around grid voltage zero-crossing points. It switches operating status from three-level state into two-level state around grid voltage zero-crossing points to enlarge the hysteresis band for digital implementation. The latter one is used to resolve fs jitter. It makes the sampling and switching to happen at the moment of current boundary-touching to achieve the most effective boundary-comparing with the lowest ADC sampling frequency. With these two techniques, fs of the grid-tied three-level NPC inverter could be well stabilized with a fully digital hysteresis controller, and therefore, high-quality grid-side could be achieved. [ABSTRACT FROM AUTHOR]

A zero-voltage switching (ZVS) grid-connected full-bridge inverter and its modulation schemes are investigated. A novel sinusoidal pulse width modulation scheme for the ZVS full-bridge inverter (ZVS SPWM) is proposed in this paper. The ZVS SPWM is evolved from the double-frequency SPWM by adding gate drive to the auxiliary switch. The ZVS condition is analyzed and the circulation loss of the resonant branch is optimized by adjusting the energy storage in the resonant inductor. The reverse recovery of the body-diode of MOSFET is relieved and ZVS is realized for both main and auxiliary switches. The filter inductors are significantly reduced with higher switching frequency. The design guideline of resonant parameters and the implementation of ZVS SPWM in DSP controller are introduced. The ZVS SPWM scheme is verified on a 3-kW inverter prototype. According to the experimental result, peak efficiency as 98.8% is achieved. [ABSTRACT FROM AUTHOR]

Class EF and Class E/F inverters are hybrid inverters that combine the improved switch voltage and current waveforms of Class F and Class F-1 inverters with the efficient switching of Class E inverters. As a result, their efficiency, output power and power output capability can be higher in some cases than the Class E inverter. Little is known about these inverters and no attempt has been made to provide an in depth analysis on their performance. The design equations that have been previously derived are limited and are only applicable under certain assumptions. This paper is the first to provide a comprehensive set of analytical analysis of Class EF and Class E/F inverters. The Class EF$_2$ inverter is then studied in further detail and three special operation cases are defined that allow it to either operate at maximum power-output capability, maximum switching frequency, or maximum output power. Final design equations are provided to allow for rapid design and development. Experimental results are provided to confirm the accuracy of the performed analysis based on a 23-W Class EF$_2$ inverter at 6.78-MHz and 8.60-MHz switching frequencies. The results also show that the Class EF $_2$ inverter achieved an efficiency of 91% compared to a 88% efficiency when operated as a Class E inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

A novel interleaved dual buck full-bridge three-level inverter (IDBFTI) is proposed for the grid-connected system in this paper. It retains the advantages of interleaved parallel technology for inverter as follows: reducing the output ripple current and the total harmonic distortion of the output current, increasing the power density of system, and reducing the current stress and thermal stress of power devices. Besides, it can solve the problem of zero sequence circulation current (ZSCC) in interleaved inverter system by the circuit structure, and it also has the advantages of no shoot-through problem, no reverse recovery of the body diode, and three-level output. The interleaved inverter circuits share two power-frequency switches, which are resized for each specific application, and it is easier to extend the system by improving current capability of the two switches. The working principle of this system is introduced in detail, and a 2-kW experimental prototype has been established and tested. Test results verify the principle and the excellent performance of IDBFTI. [ABSTRACT FROM PUBLISHER]

Carrier-based pulsewidth-modulation (CBPWM) techniques are popular due to their simplicity, and have been widely researched for various three-phase inverter configurations. In this paper, two CBPWM techniques are proposed to reduce the common-mode (CM) voltage generated by the five-phase inverter. The five-phase inverters have more flexibility in reducing the CM voltage than their three-phase counterparts because they have more phase legs, hence finer control over the star-point voltage of the load. Two methods are proposed for the conventional two-level five-phase inverter to reduce the CM voltage; one utilizing adjacent modulating waveforms and the other utilizing nonadjacent modulating waveforms. The coupled inductor inverter (CII) uses coupled inductors to generate multilevel outputs. As the volt-second balance must be maintained across each coupled inductor, direct application of the proposed methods on the CII inverter will result in overcurrents in the coupled inductors. Hence, the proposed methods are further improved to ensure the volt-second integral over each switching period is zero. Moreover, the two proposed methods are designed to reduce switching events and prevent unexpected states occurring during the switching transitions. The performance and the switching strategy of both methods are verified by both simulations and experiments on a prototype of five-phase CII. [ABSTRACT FROM AUTHOR]