Search

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

This paper proposes a multilevel series compensator (MSC) to deal with voltage sags/swells, harmonic compensation, or reactive power compensation. Such a device can be considered as a dynamic voltage restorer or a series active power filter (Series-APF). The MSC can improve the power quality of loads located in stiff systems. The configuration is based on three-phase bridge (TPB) converters connected by means of cascaded single-phase transformers. This arrangement permits the use of a single dc-link. A generalization for $K$ -stages in which $K$ -transformers are coupled with $K$-TPB converters is presented. The topology permits generating a high number of levels in the voltage waveforms with a low number of power switches in comparison with a classic topology. The multilevel waveforms are generated by the converters through a suitable pulsewidth modulation (PWM) strategy that takes into consideration the transformer turns ratios. Modularity and simple maintenance make the proposed MSC an attractive solution compared with some conventional configurations. Model, PWM strategy, and overall control are discussed in this paper. Simulation and experimental results are presented as well. [ABSTRACT FROM PUBLISHER]

This paper proposes a dual-space vector control scheme for the open-end winding permanent magnet synchronous motor (OEW-PMSM) drive fed by the dual inverter with a single dc supply. Potential zero-sequence current in the open-end winding drive system has to be considered since it causes circulating current in the winding and leads to high current stress of power semiconductor devices and high losses. Zero-sequence current in open-end winding ac motor drives is usually caused by the zero-sequence voltage, and therefore switching combinations which do not produce zero-sequence voltage are used to synthesize the reference voltage in existing methods. But even so, the zero-sequence voltage can also be produced by the dead time of the inverter. In order to suppress zero-sequence current in the OEW-PMSM drive, a dual-space vector control scheme is proposed and a novel dual-inverter space vector pulse width modulation (PWM) with the zero-sequence voltage reference is employed to regulate system zero-sequence voltage in this paper. Compared with existing dual inverter PWM strategies, the novel algorithm build a regulation mechanism for the zero-sequence voltage. The proposed method is compared with the conventional vector control by simulations and experiments, and the results shown that the proposed scheme can suppress zero-sequence current effectively. [ABSTRACT FROM AUTHOR]

The increasing interest in multiphase drive systems has led to the extension of inverter topologies and pulse width modulation (PWM) methods from three-phase to multiphase occasions. Carrier-based PWM (CPWM) dominates space vector PWM when the phase number increases, because of its simple computation and modular implementation. Although intensive work has been done on modifying PWM methods to reduce the common-mode voltage (CMV), not enough work has been done on CPWM methods with CMV reduction for multiphase drives. This paper extends the phase-shifted sinusoidal PWM (PS-SPWM) method for five-phase and six-phase two-level voltage-source inverters (VSI) and employs the intersection-plotting method and Fourier analysis to reveal the nature of the CMV. Both experiment and simulation results comply with theoretical analysis that compared with the conventional SPWM, the PS-SPWM can effectively reduce the CMV in peak-to-peak value and RMS value, though it leads to a higher phase current distortion. In addition, the hardware realization of PS-SPWM for multiphase inverters by a distributed control system is presented in this paper. [ABSTRACT FROM AUTHOR]

A switching-capacitor-based buck–boost converter (with common ground) for point of load applications is proposed in this paper. It is capable of operating in stand-alone buck or boost mode in addition to its primary operation of performing the buck–boost conversion. The striking feature of the proposed converter is low source current ripple content irrespective of its mode of operation (buck–boost, buck, or boost). First, feasible pulsewidth modulation schemes for the proposed converter are identified and thereafter the corresponding circuit performance analysis, steady-state analysis, and state-space modelling is established. Through steady-state analysis, voltage gain expressions are formulated and equations defining L-C components are derived in terms of their ripple quantities. The state-space models are used to formulate small-signal analysis and to obtain the relevant transfer functions required in the controller design. A voltage-mode/current-mode controller is designed, with a tradeoff in bandwidth, to control the proposed converter and transit it from buck to boost mode or vice versa seamlessly. A 30–55 W, 100 kHz, prototype point of load converter with 36-V input dc source is built to supply power at constant load voltage of either 48 or 28 V. The proposed converters’ effectiveness is demonstrated experimentally in terms of reduced source current ripple along with seamless transition from buck to boost mode and vice versa. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

This paper investigates an ac–dc–ac multilevel power converter. The studied configuration is composed of two single-phase ac–dc–ac three-leg modules and series-connected H-bridges in the shared part of system. Because the proposed converter has shared legs between the input and output, it is employed in applications with same input and output frequency. Uninterrupted power supply and unified power quality conditioner are application examples for this converter. Such multilevel topology has lower dc-link voltage rating, which, consequently, presents low switch blocking voltages when compared to conventional topologies. System model, a space-vector pulsewidth modulation (PWM) strategy to symmetrical and asymmetrical dc-link voltages, and an overall control strategy to adjust the system variables are presented. A power flux analysis shows the operation zone in which the individual dc-link voltage balancing is possible. PWM and control strategies are developed to reduce the semiconductor total losses, harmonic distortion, and switching stress. Two ac–dc–ac multilevel conventional structures are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper presents a nine-level transformer-based inverter requiring only eight switches. The envisaged structure consists of two standard H-bridges fed from a single dc source. Besides, a single-phase transformer is employed to aid the process of intermediate voltage level generation. An ad-hoc pulsewidth modulation scheme based on boolean logic form equations is developed to derive the gating pulses. An effortless extension of the proposed inverter to a higher number of voltage levels is also achieved by generalizing the switching functions. Furthermore, the superior performance of the proposed topology is demonstrated through a comprehensive cost-based analysis. Finally, the validation of the proposed topology is accomplished through experiments on a down-scale prototype, and the measurement results are included. [ABSTRACT FROM AUTHOR]

This paper presents the active capacitor voltage-balancing (ACVB) methods based on the dynamic model for a five-level nested neutral-point piloted (NNPP) converter using hybrid carrier modulation. The traditional hybrid carrier modulation provides natural voltage balancing of floating capacitors and dc-link capacitors. First, the natural voltage-balancing ability under steady-state and ideal conditions is theoretically proved. However, there are accumulated errors and deviations of capacitor voltages in practical applications, especially under dynamic conditions. In order to address the accumulated errors and deviations of capacitor voltages, the dynamic models of floating-capacitor voltages and neutral-point voltage are established. Moreover, the ACVB method based on the dynamic model of the neutral-point voltage is proposed by injecting the zero-sequence voltage. And the ACVB method based on the dynamic model of floating-capacitor voltages is proposed by introducing the adjustment variables. The proposed ACVB methods have the advantages of simple formula, definite physical meaning, and high accuracy. Furthermore, the output voltage quality and current quality are evaluated in term of total harmonic distortion and the effect of model parameter mismatch on the proposed ACVB methods is presented. Finally, the comparative simulation and experimental results verify the correctness of the proposed ACVB methods based on the dynamic model under different conditions. [ABSTRACT FROM AUTHOR]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

The noninverting buck–boost converter has attracted significant attention in the photovoltaic (PV) module integrated application, as it offers high efficiency while maintaining a low cost and a simple topology. When this converter is employed, special care must be taken at the transition between buck and boost operating modes, as a dead-zone in the voltage transfer function can cause abrupt perturbations in the controlled voltage, decreasing the regulation quality and ultimately lowering the power conversion efficiency. In this paper, a new dead-zone compensation technique is proposed with the scope of smoothing the transition between operating modes, eliminating the voltage ripple and improving the regulation performance, while maintaining high efficiency. The converter under analysis is studied together with its gate driving circuit, which is based on a bootstrap capacitor power supply for the high-side switches. The proposed dead-zone compensation technique is deduced by using the principle of maintaining the ideal voltage gain function across the converter operating range. The technique is analyzed, implemented and tested on a purposely built PV module integrated noninverting buck–boost converter. The experiments reveal a sensible improvement of the voltage regulation during mode transition, confirming the effectiveness of the proposed technique and its fitness for the PV application. [ABSTRACT FROM AUTHOR]

Five-level hybrid-clamped (5L-HC) converter is a newly proposed topology which is suitable for high-performance medium-voltage high-power conversions without switches directly connected in series. The critical issue of this converter is that two flying capacitor voltages of each phase and two neutral-point potentials of the dc-link need to be balanced. This paper presents a decoupled voltage balancing method for this 5L-HC converter based on modified phase-shifted pulse width modulation (PS-PWM) and optimal zero-sequence voltage injection. The voltages across the central dc-link capacitor and two flying capacitors are balanced first by adjusting the width of four PWM signals. Second, the relationship between the neutral-point currents and the output phase voltage is studied and the upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection. Both steady-state and dynamic-state simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques. [ABSTRACT FROM AUTHOR]

This paper presents an optimized topology for a \text3-\phi three-level inverter with complete elimination of common-mode voltage (CMV). The proposed multilevel inverter (MLI) configuration is realized by modifying a T-structure \text3-\phi inverter. The proposed configuration is an optimized solution with respect to the pulse-width modulation strategy used for CMV elimination. The given three-level inverter structure uses only 16 power semiconductor switches, which is much lower than the existing configurations. A reduced number of power semiconductor devices results in a diminished number of driver circuits, less installation space, and low cost. Further, due to the complete elimination of CMV, the proposed MLI is free from issues such as electromagnetic interference and leakage current with a reduction in filter requirement. The presented topology is also compared with other existing topologies to prove its advantage. It is an optimized solution with respect to the dc bus voltage requirement and the total voltage rating of the devices or the components used in the system. Simulation and experimental results are presented to confirm the capability of the proposed MLI. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) is a newly emerging multilevel topology for high-voltage applications during recent years. In this paper, a new MMC is proposed, and the structure and operating principle are analyzed. Owing to the cascaded basic cells without multiwinding transformer, the voltage balancing of floating capacitors must be considered. However, the voltage fluctuation also exists, and theoretical analysis indicates that the amplitude is inversely proportional to the fundamental frequency. This paper has proposed a voltage-fluctuation-suppression method which can reduce the amplitude of the voltage fluctuation in low-frequency region. It can also be used in motor driving with pump/blowerlike load at low frequency and improve the start-up performance significantly. A low-power three-phase five-level prototype is designed and built up to demonstrate the validity of this method. [ABSTRACT FROM PUBLISHER]

This paper discusses the implementation of level-shifted and phase-shifted carrier-based modulation methods, in conjunction with a multiphase open-end winding drive topology. The considered drive is supplied using two five-phase two-level voltage source inverters (VSIs), with input provided from two isolated supplies of equal dc voltages. The topology is known to yield the same space-vector pattern as a corresponding three-level inverter in single-sided supply mode. It is shown in this paper that, with the application of a simple logic, the same phase voltage waveforms result as those obtainable with the appropriate carrier-based modulation scheme applied to the three-level VSI in single-sided supply mode. While the outcomes of the modulation techniques are the same, the open-end winding topology offers certain advantages, such as modularity and absence of capacitor voltage balancing requirements. The analysis is conducted for selected modulation methods using voltage and current waveforms, spectra Fast Fourier Transform (FFT), and total harmonic distortion as figures of merit. Theoretical considerations are verified by means of simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-phase, single-stage buck–boost inverter for photovoltaic (PV) systems. The presented topology has one common terminal in input and output ports which eliminates common mode leakage current problem in the grid-connected PV applications. Although it uses four switches, its operation is bimodal and only two switches receive high-frequency pulse width modulation signals in each mode. Its principle of operation is described in detail with the help of equivalent circuits. Its dynamic model is presented, based on which a bimodal controller is designed. Experimental results, in stand-alone and grid-connected mode, obtained with a 300-W laboratory prototype are presented to validate its performance. [ABSTRACT FROM AUTHOR]

This paper presents a novel technique for the voltage droop compensation of long pulses in solid-state bipolar high-voltage Marx generators. Considering the modularity of Marx generators the compensation consists in adding one extra stage to perform as a pulsewidth modulation circuit. This stage voltage is added to the output positive or negative pulses, and an output LfCf filter is included to smooth the voltage pulse waveform. A five-stage laboratory prototype of this circuit has been assembled using 1200-V Insulated Gate Bipolar Transistors and diodes with 1000-V dc input voltage. The circuit was operated at 50-Hz bipolar pulse rate, giving 4-kV bipolar pulses, into a resistive load, with 100- \mu \texts pulsewidth and 9.5-ms relaxation time. The circuit was able to compensate 10% of bipolar pulse voltage droop. [ABSTRACT FROM PUBLISHER]

This paper addresses the inverter nonlinearity of a three-level T-type inverter. The main causes of the nonlinearity are pulse shaping, pulse skipping due to narrow pulses for the dead time, and voltage drop of the switching devices. Although the same causes have existed in two-level inverters, the pulse skipping phenomenon and results are quite different in the case of the three-level T-type inverter. The effects of pulse shaping and skipping have been investigated and discussed. In addition, the voltage drop of the switching devices has been considered in conjunction with the conduction path of the T-type inverter. Compensation methods based on the pulse width modulation (PWM) of T-type inverter to alleviate the inverter nonlinearity have been proposed from research results. The proposed methods could be easily implemented by adding appropriate offset voltages to the voltage references of the inverter in PWM. Furthermore, a neutral voltage balancing method of a three-level T-type inverter has been proposed in conjunction with the proposed PWM methods using offset voltage. Through extensive experimental tests, the fifth- and seventh-harmonic components of the current are conspicuously reduced along with the even harmonics. The neutral voltage of the inverter can be balanced effectively with the proposed offset voltage adjustments as well. [ABSTRACT FROM AUTHOR]

This paper proposes and investigates a new three-phase ac–dc–ac multilevel conversion system obtained from cascaded three-leg converters. Such configuration presents advantages in terms of reduced switch blocking voltages and consequently lower dc-link voltage rating. Operating principles, a pulse-width modulation (PWM) technique based on vector approach, and a control strategy are presented. The operation with different dc-link voltage values and a balancing method are discussed, and is supported by simulation and experimental results. The PWM technique is able to generate multilevel voltage waveforms, which permits reducing the switching frequency stress leading to reduced semiconductor losses. Simulation results are used to compare the proposed configuration with a conventional solution in terms of harmonic distortion and semiconductor losses. Experimental results demonstrate the feasibility of the studied converter, and were obtained by using a downscaled prototype with insulated gate bipolar transistors with dedicated drives and a digital signal processor with appropriated plug-in boards and sensors. [ABSTRACT FROM PUBLISHER]

By using a carrier-based pulse width modulation, this paper presents a developed phase-shift space vector modulation strategy for a nine-switch inverter to overcome one of major drawbacks, i.e., output voltage and current distortion. This is due to the crossover of modulating waves per phase based on the different phase-shift angle between dual terminals. The proposed strategy done by mathematical algorithms based on the critical operating point principle accomplishes in the wide range of phase-shift conditions that contribute in both common- and difference-frequency modes with its expediency of uncomplicated computation and handy implementation. Even more, the identical and nonidentical modulation index techniques are wholly brought up. The feasibility of the proposed strategy is confirmed by results of the simulation directly compared with the experiment, showing in good accordance with the theoretic analysis. [ABSTRACT FROM AUTHOR]

Multiple output converters (MOCs) are widely applied to applications requiring various levels of output voltages due to their advantages in terms of cost, volume, and efficiency. However, most of the conventional MOCs cannot regulate multiple outputs tightly and they can barely avoid the cross-regulation problem. In this paper, the recently developed time-division multiple control (TDMC) method, which can regulate all of the outputs with a high accuracy, is used for a multiple output battery charger based on the phase-shift full-bridge topology to simultaneously charge three batteries. The proposed charger is able to charge three different kinds of batteries or three of the same kind of battery in different state of charges (SOCs) independently and accurately with the constant current/constant voltage (CC/CV) charge method. As a result, the strict ripple specification of a battery can be satisfied for multiple battery charges without difficulty. In addition, the proposed charger exhibits a high efficiency since the soft switching of all of the switches during the entire charge process can be guaranteed. The operating principle of the converter and the design of the controller, including the state-space average modeling, will be detailed, and the validity of the proposed method is verified through experiments. [ABSTRACT FROM PUBLISHER]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

The flying-capacitor-based multilevel converter is one of the well-known breeds of the multilevel power converters. This paper proposes a new flying-capacitor-based multilevel converter to minimize the number of flying capacitors (FCs) and power switches. The advantage of the proposed FC-based multilevel converter in comparison with the conventional flying-capacitor multicell converter is that it needs fewer FCs. Also, in comparison with the stacked multicell converter, the proposed multilevel converter requires fewer semiconductor switches. In order to balance the voltage of the FCs in proposed multilevel converter, a new active voltage balancing method which is fully implemented using logic-form equations is presented. The proposed voltage balancing method measures output current and FC voltages to generate switching states to produce the required output voltage level, as well as balance the FCs voltages at their reference values. The output voltage of the proposed multilevel converter controlled with suggested active voltage balancing method can be modulated with any pulse-width-modulation (PWM) method, such as phase-shifted-carrier PWM or level-shifted-carrier PWM. Simulation results and experimental measurements of proposed FC-based multilevel converter are presented to verify the performance of the proposed converter, and its novel switching and modulation strategy, which is based on the active voltage balancing method. [ABSTRACT FROM PUBLISHER]

This paper presents a novel topology for a direct ac–ac power converter, called as the “three-to- k” phase matrix converter. The input to the proposed matrix converter configuration is a three-phase fixed voltage and a fixed frequency supply from the grid. The output is a variable voltage and variable frequency ac supply of any number of phases (k phase). However, the discussion is limited here for a k that is equal to odd number of phases. As an example, a “three-to-five” phase matrix converter is utilized for discussion and analysis. This paper also proposes two pulsewidth modulation (PWM) control techniques for the general topology of the “three-to- k” phase matrix converter. This is based on the so-called direct duty ratio PWM (DPWM). In one presented technique, the output voltage is limited to one half of the input voltage. For the other proposed scheme, the output voltage is enhanced to 78.86% of the input voltage. The proposed control algorithm is validated using simulation and an experimental approach. [ABSTRACT FROM AUTHOR]

This paper proposes a new type of ac–ac converter which can operate as traditional noninverting buck and boost converters, and inverting buck–boost converter as well. The proposed converter uses six unidirectional current flowing and bidirectional voltage blocking switches, implemented by six reverse blocking insulated-gate bipolar transistors (IGBTs) or series mosfet–diode pairs, two input and output filter capacitors, and one inductor. It has no shoot-through problem of voltage source (or capacitor) even when all switches are turned-on, and therefore, pulsewidth modulation dead-times are not needed resulting in high-quality waveforms, and solves the commutation problem without using bulky and lossy RC snubbers or dedicated soft-commutation strategies. It has smaller switching losses because only two switches out of six are switched at high frequency during each half-cycle of input voltage, and it can use power MOSFETs as body diode never conducts, making it immune from mosfet failure risk which otherwise may occur due to poor reverse recovery problem of body diode. The noninverting buck–boost mode of the proposed converter can be used in applications with both step-up and step-down demand, while the inverting buck–boost mode can also be used in its application as dynamic voltage restorer. Detailed analysis of the proposed converter is given, and experimental results are also provided. [ABSTRACT FROM AUTHOR]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

This paper proposes and evaluates an active voltage-balancing method for stacked multicell converters (SMCs) using phase-shifted pulse width modulation. The method is easy to implement and can be applied to SMCs with any number of levels. The proposed method balances the voltages of the capacitors by modifying the duty cycle of each switch of the SMC using a proportional controller. The direction of the output current and the crossed effect among the duty cycles of the switches is considered and used to improve capacitor voltage balance. The performance of the proposed voltage-balancing method is verified experimentally for different loads, such as linear and nonlinear loads, and under transient conditions. [ABSTRACT FROM PUBLISHER]

A capacitor voltage-balancing method for a nested neutral point clamped (NNPC) inverter is proposed in this paper. The NNPC inverter is a newly developed four-level voltage-source inverter for medium-voltage applications with properties such as operating over a wide range of voltages (2.4–7.2 kV) without the need for connecting power semiconductor in series and high-quality output voltage. The NNPC topology has two flying capacitors in each leg. In order to ensure that the inverter can operate normally and all switching devices share identical voltage stress, the voltage across each capacitor should be controlled and maintained at one-third of dc bus voltage. The proposed capacitor voltage-balancing method takes advantage of redundancy in phase switching states to control and balance flying capacitor voltages. Simple and effective logic tables are developed for the balancing control. The proposed method is easy to implement and needs very few computations. Moreover, the method is suitable for and easy to integrate with different pulse width modulation schemes. The effectiveness and feasibility of the proposed method is verified by simulation and experiment. [ABSTRACT FROM PUBLISHER]

In this paper, a modified half-bridge (HB) resonant inverter topology with a dc-link neutral-point-clamped cell is proposed. A pseudo asymmetrical voltage-cancellation PWM method and a control strategy are introduced. The proposed topology can maximize the inverter output power factor, and minimize variations in the switching frequency. In addition, most switches are clamped to half of the dc input voltage at turn-off, increasing the overall efficiency of the system for a wide load range. The efficiency of the proposed inverter is improved up to 7% at light-load conditions compared with that of the conventional HB inverter. Informative expressions for performance comparison between the proposed inverter and its counterpart are provided. In addition, the losses in the inverter primary components are analytically analyzed in detail. For validation, a 120-W prototype is implemented, and experimental results are presented. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel single-phase ac–ac Z-source converter based on the Γ-structure. The proposed converter uses a coupled transformer to produce the required gain. The obtained gain can be tuned by varying the turn ratio $\gamma _\Gamma$ of the transformer within the narrow range of $1 < \gamma _\Gamma < 2$. Also, the gain factor increases with decrease of the transformer turns ratio, $\gamma _\Gamma$ . Small transformer turn ratio results in more practical topology in some voltage gains. It makes the transformer design easier and reduces construction cost. Also, in the proposed topology, the input and output voltages share the same ground. In order to avoid voltage and current spikes on the switches, a commutation strategy is proposed and safe commutation is achieved without using a snubber circuit. The operating principles and steady-state analyses are presented to verify the operational concept of the proposed topology. Also, experimental results are given to verify the validation of the proposed converter. [ABSTRACT FROM AUTHOR]

A novel complementary phase disposition pulsewidth modulation method for the modular multilevel converter (MMC) with a limited number of submodules is proposed in this paper. Compared with the previous works, more practical issues have been considered, and the corresponding solutions have been provided. First, a new preset PWM signal mapping sequence and an improved virtual loop mapping (VLM) are used in the modulation. This method not only achieves a favorable capacitor voltage balance in the symmetry system but lowers the switching frequency of MMC's devices. Second, to further reduce the switching frequency, the unbalance margin of capacitor voltages is adopted to achieve the switching between the VLM and the selective VLM (SVLM). Moreover, the system robustness has been improved by considering the situation of symmetry losing, like cell fails; in these cases, the capacitor voltages of the upper and lower arms are balanced through the collaboration of the SVLM and the reconfigurable VLM. Finally, the effectiveness of the proposed method has been verified with simulation and experimental studies. [ABSTRACT FROM AUTHOR]

This paper investigates a dynamic voltage restorer (DVR) composed of two conventional three-phase inverters series cascaded through an open-end winding (OEW) transformer, denominated here DVR-OEW. The DVR-OEW operating with either equal or different dc-link voltages is examined. The proposed topology aims to regulate the voltage at the load side in the case of voltage sags/swells, distortion, or unbalance at the grid voltage. A suitable control strategy is developed, including space-vector analysis, level-shifted PWM and its equivalent optimized single-carrier PWM, as well as the operating principles and characteristics of the DVR. Comparisons among the DVR-OEW and conventional configurations, including a neutral-point clamped converter-based DVR, are furnished. The main advantages of the DVR-OEW compared to the conventional topologies lie on: 1) reduced harmonic distortion, 2) reduced converter losses, and 3) reduced voltage rating of the power switches. Simulated and experimental results are presented to validate the theoretical studies. [ABSTRACT FROM AUTHOR]

This paper presents a capacitor voltage balancing control applicable to any multilevel dc–ac converter formed by a single set of series-connected capacitors implementing the dc link and semiconductor devices, such as the diode-clamped topology. The control is defined for any number of dc-link voltage levels and converter legs (for single-phase and multiphase systems), guaranteeing the capacitor voltage control for any modulation index value and load (from idle mode to full power). The associated control loop small-signal transfer function is presented, from which optimum compensator design guidelines are derived. The improvement in control performance is verified through simulation and experiments comparing with a previous balancing control strategy in a four-level three-phase dc–ac conversion system. The satisfactory control performance is also verified through simulation in a four-level five-phase dc–ac conversion system. [ABSTRACT FROM PUBLISHER]

Five-level active neutral-point clamped (5L-ANPC) converter is an attractive topology for high-power medium-voltage motor drives. This paper presents a capacitor voltage-balancing method for the 5L-ANPC converter, including the voltage balancing of dc-link capacitors and flying capacitors. In order to ensure that the series-connected or high-voltage switches of the 5L-ANPC converter are operated at fundamental frequency and the other switches are operated at a constant switching frequency, phase-shifted pulse width modulation is used to control this converter. The relationship between the average neutral-point current and zero-sequence voltage is investigated, and an optimum zero-sequence voltage is calculated to regulate the neutral-point potential. The voltage across the flying capacitor is also regulated by adjusting the switching duty cycles of two PWM signals, which varies the operation time of redundant switching states in each switching period. Simulation and experimental results are presented to verify the validity of this method. [ABSTRACT FROM AUTHOR]

Dodecagonal (12-sided) space vector pulsewidth modulation (PWM) schemes are characterized by the complete absence of (6n ± 1)th-order harmonics (for odd n) in the phase voltages, within the linear modulation range and beyond, including overmodulation. This paper presents a new topology suitable for the realization of such multilevel inverter schemes for induction motor (IM) drives, by cascading two-level inverters with flying-capacitor-inverter fed floating H-bridge cells. Now, any standard IM may be used to get the dodecagonal operation which hitherto was possible only with open-end winding IM. To minimize the current total harmonic distortion (THD), a strategy for synchronous PWM is also proposed. It is shown that the proposed method is capable of obtaining better THD figures, compared to conventional dodecagonal schemes. The topology and the PWM strategy are validated through analysis and subsequently verified experimentally. [ABSTRACT FROM AUTHOR]

Multilevel inverters have been widely accepted for high-power high-voltage applications. Their performance is highly superior to that of conventional two-level inverters due to reduced harmonic distortion, lower electromagnetic interference, and higher dc link voltages. However, it has some disadvantages such as increased number of components, complex pulsewidth modulation control method, and voltage-balancing problem. In this paper, a new topology with a reversing-voltage component is proposed to improve the multilevel performance by compensating the disadvantages mentioned. This topology requires fewer components compared to existing inverters (particularly in higher levels) and requires fewer carrier signals and gate drives. Therefore, the overall cost and complexity are greatly reduced particularly for higher output voltage levels. Finally, a prototype of the seven-level proposed topology is built and tested to show the performance of the inverter by experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a novel single-phase five-level inverter is proposed using coupled inductors. This inverter can output five-level voltage with only one dc source. No split of the dc voltage capacitor is needed, totally avoiding the voltage balancing problem in conventional multilevel inverters. The level of the output voltage is only half of the dc-link voltage in all conditions, leading to much reduced dv/dt . This inverter is based on the widely used three-arm power module and the voltage stresses on all the power switches are the same, making it very easy to construct. Operation mechanism of this inverter is analyzed and the possible switching patterns are investigated. Based on these analyses, a novel optimized modulation scheme is presented. With this modulation method, no dc components exist in the inductor currents, which is very helpful for minimization of the inductors. Simulation and experimental results show the validity of the proposed inverter together with the optimized modulation scheme. [ABSTRACT FROM AUTHOR]

Flying-capacitor converters (FCCs), like most multilevel converter topologies, require a balancing mechanism of the capacitor voltages. FCCs feature natural voltage balancing when a special modulation technique is used. The classic methods, such as phase-shifted pulse width modulation (PS-PWM), result in very slow balancing for some duty-ratio ranges. Previous work has shown that for a single-leg five-level FCC, one time constant is infinite for a zero desired output voltage. In this paper, a modified PS-PWM scheme for a single-leg five-level FCC is presented, which results in faster balancing over the total duty-ratio range. The modified PS-PWM scheme is studied, resulting in an averaged voltage-balancing model. This model is verified using simulations and experiments. The modified PS-PWM scheme solves the slow-balancing problems of the normal PS-PWM method for odd-level FCCs, while maintaining the passive control property, and it provides a self-precharge capability. [ABSTRACT FROM AUTHOR]

In this paper, a new three-level (3L) converter is presented. It is called 3L Vienna neutral-point-clamped (3L-VNPC) converter and consists of two stacked high-frequency (HF) commutation cells working with a shared power device. The HF cells are connected to a single-phase switched bridge controlled at low frequency. The 3L-VNPC topology is extended to 3L active VNPC (3L-AVNPC) concept, which is generalized for five levels (5L) and N odd voltage levels (N \L). The proposed multilevel converters can be seen as two cascaded voltage stages. The high-voltage stage is specific to the single-phase switched bridge, while the low-voltage (LV) stage corresponds to the stacked HF cells with shared power devices. The new concept AVNPC is a useful and suitable solution for medium-voltage applications, where small modulation index (M) is as crucial as large M. The analyses of the new converters are verified by simulations both for 3L and for 5L topologies, and their features are generalized for N\L. Experimental results for single-phase 3L-AVNPC converter on an LV test bench are also provided to validate the proper operation of the new concept. [ABSTRACT FROM AUTHOR]

The novel multilevel circuit topologies are proposed in this paper. They are called multilevel circuit topologies based on switched-capacitor and diode-clamped converters (MCT-BSD). The topology structure and the operation principle, including the working states’ transitions of the diode-clamped part, the voltages balancing mechanism of the dc link capacitors, and the pulse width modulated carrier control strategy are given. The switched-capacitor circuits contribute not only to balancing the voltages of capacitors but also to boosting the output voltage with a certain input dc voltage. The validity of the MCT-BSD is verified by simulations and experiments. The results show that balancing the voltages of capacitors, boosting the output voltages, and operating under the three-phase condition are all realized effectively in the MCT-BSD. The simulations also show the generalization of the MCT-BSD for n-level topologies. [ABSTRACT FROM AUTHOR]

Unipolar sinusoidal pulsewidth modulation (SPWM) full-bridge inverter brings high-frequency common-mode voltage, which restricts its application in transformerless photovoltaic grid-connected inverters. In order to solve this problem, an optimized full-bridge structure with two additional switches and a capacitor divider is proposed in this paper, which guarantees that a freewheeling path is clamped to half input voltage in the freewheeling period. Sequentially, the high-frequency common-mode voltage has been avoided in the unipolar SPWM full-bridge inverter, and the output current flows through only three switches in the power processing period. In addition, a clamping branch makes the voltage stress of the added switches be equal to half input voltage. The operation and clamping modes are analyzed, and the total losses of power device of several existing topologies and proposed topology are fairly calculated. Finally, the common-mode performance of these topologies is compared by a universal prototype inverter rated at 1 kW. [ABSTRACT FROM AUTHOR]

Multilevel cascaded H-bridge converters have found industrial application in the medium-voltage high-power range. In this paper, a generalized modulation technique for this type of converter based on a multidimensional control region is presented. Using the multidimensional control region, it is shown that all previous modulation techniques are particularized versions of the proposed method. Several possible solutions to develop a specific implementation of the modulation method are addressed in order to show the potential possibilities and the flexibility of the proposed technique. In addition, a feedforward version of this technique is also introduced to determine the switching sequence and the switching times, avoiding low harmonic distortion with unbalanced dc voltages. Experimental results are shown in order to validate the proposed concepts. [ABSTRACT FROM AUTHOR]

The focus of this paper is the study of direct alternating-current (ac)–ac converters, beginning by buck, half-bridge, full-bridge, and push–pull converters. From the basic converters, we apply a simple methodology to make the use of switches in commercial configurations possible. Following that, eight voltage restorers supplied either on the line side or on the load side are proposed. A comparative evaluation of these topologies concerning implementation, complexity, and component effort is presented. It is notable that some of the studied topologies are known in the literature and others are new. For one of the presented topologies, the design of a 3-kVA voltage restorer is developed, and experimental results are shown, certifying the correct operation of the drive strategy used. [ABSTRACT FROM AUTHOR]