Search

The pulp and paper industry accounts for approximately 5% of total industrial energy consumption and contributes 2% of direct carbon dioxide (CO 2 ) emissions from industries. World paper and paperboard demand and production are increasing significantly, leading to an increase in this sector's energy use and CO 2 emissions. Although current studies identify a wide range of energy-efficiency technologies that have already been commercialized for the pulp and paper industry, information is limited or scattered regarding new energy-efficiency technologies that are not yet fully commercialized. Development of emerging or advanced energy-efficiency technologies and their deployment in the market will be crucial for this industry's mid- and long-term energy saving and climate change mitigation strategies. This paper compiles available information on energy savings, environmental and other benefits, costs, and commercialization status for 25 emerging technologies to reduce the energy use and CO 2 emissions. The purpose is to provide a well-structured comprehensive review on these emerging energy-efficiency technologies for engineers, researchers, investors, policy makers, pulp and/or paper companies, and other interested parties. [ABSTRACT FROM AUTHOR]

The pulp and paper industry is a high energy consuming and polluting sector, and carbon emissions emitted from this sector are worthy of attention. This article, based upon an analysis of China’s Pulp and Paper Industry (CPPI), provides estimates of each of the following: carbon emissions from energy consumption, pre-treatment sector, combustion of condensed black liquor, and methane emitted from incomplete aerobic digestion during sewage treatment of CPPI. During the study period (2005–2012), total CO 2 emissions ranged from 126.0 Mt to 155.4 Mt. Energy consumption was estimated to be the largest source of carbon emissions, however, due to the application of the local emission inventory rather than the IPCC inventory, energy consumption decreased by 4.7%, a lower percentage than was calculated in a previous study. According to this study’s estimation, the emissions caused by the recovery of biomass energy contributed 26–29% of the total CO 2 emissions. CH 4 generated from sewage treatment accounted for 9–11% of the total carbon emissions. The CO 2 intensity dropped during the study period, which reflected the improvement of energy efficiency in the pulp and paper industry. The outcome of this study provides not only detailed information about CPPI’s carbon emissions, but also a calculation framework for studying carbon emissions from pulp and paper sector in the other regions. It suggests that the local carbon emissions inventory should be used for estimating carbon emissions and to reduce the fossil fuel energy, increase energy recovery from biomass, and that promoting cleaner production is essential to achieve a low carbon development of the pulp and paper industry. [ABSTRACT FROM AUTHOR]

Abstract With fast development and urbanization, Chinese cities are facing several challenges including issues of environmental pollution, climate change, resource depletion and landfills shortage. Waste recycling is one effective way to respond these challenges. Under such a situation, this paper aims to evaluate energy saving and carbon reduction potential of recycling wastes by taking Shanghai, the biggest city in China, as a case study. Results show that 8.7 Mt standard coal (tce) and 16.81 Mt CO 2 could be reduced under current recycling system in Shanghai. And recycling of waste steel and nonferrous metals were the two dominant contributors, accounting for about 44% and 42% of energy saving, and 60% and 33% of CO 2 reduction, respectively. If the recycling rates of main recyclable wastes were improved to 100%, additional 6.44 Mt energy and 10.02 Mt CO 2 could be further saved, mainly from recycling waste glass, waste plastic and waste metals. Adoption of RPF (Refuse Plastic & paper Fuel) could further contribute to 1.24 Mt energy saving and 2.67 Mt CO 2 reduction. Finally, policy implications on establishing a mature recycling system and promoting RPF technologies are discussed, in which the potential on reducing total energy consumption and CO 2 emission of Shanghai can reach 6.6% and 4.9%, respectively. [ABSTRACT FROM AUTHOR]

The energy crisis caused by climate change is the most significant challenge of the 21st century. Single-objective and multi-objective optimization studies for buildings often only consider the building itself, without considering the impacts of climate change. However, in the future, energy-efficient design and appropriate operating parameters will be crucial considerations in the face of global climate change. This paper aims to discuss the impact of climate change in the humid-hot region over the past 60 years on the energy consumption of office buildings and propose countermeasures. Firstly, the meteorological data of Guangzhou from 1960 to 2020 is statistically analyzed, and four typical meteorological years and corresponding air conditioning design days are established. Secondly, Energyplus is used to simulate the building's energy consumption, and the energy consumption factors are analyzed for sensitivity using jEplus. Finally, a multi-objective optimization is performed using jEPlus + EA with the Non-dominated Sorting Genetic Algorithm (NSGA-II). The results found that climate change led to a significant increase in the duration of high outdoor temperatures during summer. Specifically, the daily dry-bulb temperature for air conditioning design increased by 0.4–0.7 °C, and due to climate change, the energy consumption of the office building increased by about 4.6 %. The main factor affecting the cooling energy consumption in summer was the indoor cooling set point (8.29%–30%), infiltration air volume (1.0%–8.6%), fresh air volume (3.2%–16.06%), the glazing solar transmission rate (1.25%–9.0%), building orientation (0%–1.43%), and relatively small influence of envelope insulation performance. The operation scheme determined by multi-objective optimization can reduce the cooling energy consumption of the building by 10.6%–16.8%, which can mitigate the rise in energy consumption resulting from climate change to a greater extent. [Display omitted] • Discuss the impact of climate change over the past 60 years on the energy consumption of office buildings. • There was a significant increase in the duration of high outdoor temperatures during the summer. • Multi-objective optimization is performed using jEPlus + EA. • Climate change caused energy consumption to increase by about 4.6 %. • Optimal solutions can reduce the cooling energy consumption of the building by 10.6%–16.8%. [ABSTRACT FROM AUTHOR]

This paper studies the influence of temperature and of rainfall intensity and the effect of such variations on the treatment efficiencies and on the electrical consumptions in seven medium-large size Wastewater Treatment Plants (WWTPs) in Apulia in South Italy (Bari, Barletta, Brindisi, Lecce, Foggia, Andria and Taranto). It has been observed, in the considered WWTPs, a slight but clear increase of the incoming flow due to the increase in rainfall intensity, which results to an increase of the energy consumption per incoming volume. The impact of the climate change to the incoming flow, during the last five years (2016–2020), has been assessed indicating that an increase in rainfall intensity results to an increase of the WWTPs energy consumptions per wastewater treated volume. More specifically, for a specific WWTP (Lecce) it was found that the electrical consumption increases from 0.36 kw/m3 to 0.51 kw/m3 when the rainfall intensity was increased from 0.8 mm/min to 2.9 mm/min. Some adaption measures have been considered to upgrade the existing WWTP so to mitigate the energy increase and to limit the global effects of climate change. [Display omitted] • As Rain intensity rises, wastewater influx into WWTPs increases. • Rainfall intensity influences negatively electrical consumptions. • BOD removal is lower with increasing annual precipitations. • Temperature influences BOD, COD and SST removal efficiency. [ABSTRACT FROM AUTHOR]

Given the significant energy consumption and carbon emissions associated with buildings, there is increasing interest in improving sustainability of building operations to reduce impact on climate change. A common goal is to operate buildings as "net-zero" energy users in which all energy consumed by the building is balanced against renewable energy purchased from the grid or produced on site. To achieve net-zero status, many buildings will require significant retrofit so as to both reduce energy consumption in the absolute sense and provide the remainder without consuming fossil fuels. Thus, multi-year planning is required to ensure that goals can be met on time. In addition, due to the inherent uncertainty associated with energy consumption and generation, actually achieving net-zero energy use may require discretionary curtailment actions to be taken, and deciding whether such actions are necessary can be challenging. To address these challenges, we propose in this paper a design optimization and operational planning strategy to make the decisions needed to achieve sustainability goals in buildings. The strategy can be applied to schedule design changes over a long horizon to meet annual targets, and it can also be applied in closed loop on a shorter horizon to determine whether curtailment is needed to stay on track. We discuss the formulation of the optimization problem, solution methods, and modeling approaches for key parameters. Application of the strategy is illustrated via examples. Overall, this approach will help automate planning that is often done manually, allowing buildings to take a significant leap forward toward achieving their sustainability goals. • Achieving sustainability goals in buildings requires multi-year planning. • The required design and operational decisions can be made via optimization. • Key problem parameters can be obtained from data-driven modeling. • The strategy allows sustainability goals to be met at minimum cost. [ABSTRACT FROM AUTHOR]

• Overheating regulations and calculation methods in 26 European countries were compared. • Most of the existing calculation methods are outdated and do not fit climate-proof buildings. • France requires a mixed-mode operation of naturally ventilated households. • The UK developed a heatwave-based calculation approach. • Comfort-based, multi-zonal, and time-integrated calculation approaches are needed. With the ongoing significance of overheating calculations in the residential building sector, building codes such as the European Energy Performance of Building Directive (EPBD) are essential for harmonizing the indicators and performance thresholds. This paper investigates Europe's overheating calculation methods, indicators, and thresholds and evaluates their ability to address climate change and heat events. e study aims to identify the suitability of existing overheating calculation methods and propose recommendations for the EPBD. The study results provide a cross-sectional overview of twenty-six European countries. The most influential overheating calculation criteria are listed the best approaches are ranked. The paper provides a thorough comparative assessment and recommendations to align current calculations with climate-sensitive metrics. The results suggest a framework and key performance indicators that are comfort-based, multi-zonal, and time-integrated to calculate overheating and modify the EU's next building energy efficiency regulations. The results can help policymakers and building professionals to develop the next overheating calculation framework and approach for the future development of climate-proof and resilient residential buildings. [ABSTRACT FROM AUTHOR]

Abstract Railways are a rather efficient transport mean, and yet there is increasing interest in reducing their energy consumption and making them more sustainable in the current context of climate change. Many studies try to model, analyse and optimise the energy consumed by railways, and there is a wide diversity of methods, techniques and approaches regarding how to formulate and solve this problem. This paper aims to provide insight into this topic by reviewing up to 52 papers related to railways energy consumption. Two main areas are analysed: modelling techniques used to simulate train(s) movement and energy consumption, and optimisation methods used to achieve more efficient train circulations in railway networks. The most used methods in each case are briefly described and the main trends found are analysed. Furthermore, a statistical study has been carried out to recognise relationships between methods and optimisation variables. It was found that deterministic models based on the Davis equation are by far (85% of the papers reviewed) the most common in terms of modelling. As for optimisation, meta-heuristic methods are the preferred choice (57.8%), particularly Genetic Algorithms. Highlights • Modelling and optimisation methods for railways energy efficiency are reviewed. • Modelling methods provide reliable simulations of the trains' energy consumption. • Optimisation methods help obtaining the most efficient solutions for train traffic. • Most used modelling methods are deterministic, based on Davis equation. • Most used optimisation methods are meta-heuristics, mainly genetic algorithms. [ABSTRACT FROM AUTHOR]

Abstract Energy efficiency improvement is usually regarded as an effective way to decrease energy consumption and to fight climate change, but it also booms energy consumption through rebound effects. But the improvement of energy efficiency also has rebound effects, which increases energy consumption and emission. So this paper arms to capture the rebound effects of efficiency improvement by considering zero-cost breakthrough of energy efficiency and price jump of energy purchase. First, energy efficiency improvement, measured by zero-cost breakthrough of energy efficiency, stimulates energy consumption, but it may reduce the total emission. Second, both the direct and indirect rebound effects of energy efficiency improvement on energy consumption and environment are captured. Interestingly, jumping energy price decreases both the direct and indirect rebound effect. Finally, the result of the paper shows that restriction of individuals' entry or competition restriction moderates the rebound effects of energy efficiency improvement. Highlights • Effect of competition on energy efficiency rebound effects is developed in theory. • Rebound effects of energy efficiency are captured under zero-cost breakthrough. • Moderate monopoly is proofed to be helpful for reducing energy efficiency rebound effects. • Improvement of energy efficiency has both direct and indirect rebound effects. • Energy price jump has offset effects on rebound effects of efficiency promotion. [ABSTRACT FROM AUTHOR]

The growing awareness of climate change is constantly moving the attention of designers and policymakers from typical and current scenarios to future layouts. This new approach introduces a degree of uncertainty that should be accounted in the building design process. The multitude of possible scenarios suggests considering dynamic system that can adapt themselves to unpredicted operating conditions. The aim of this study is to test a new approach and a new flexibility metric analysing the behaviour of a high-performance dynamic internal curtain in current and future scenarios. The first part of the paper focuses on the optimization of the dynamic system in the current scenario; this preliminary analysis represents the traditional design approach and is considered the baseline for all the comparisons. Hence, defining a matrix of likely scenarios, this paper explores the behaviour of three different selected control strategies – always off (i.e., no curtain), fixed control, optimized control – in the different scenarios considering possible variations of i) climate, ii) urban context, iii) internal loads, and iv) building use. The main outcomes of the research are, on the one hand, the comparisons of the control strategies and the benefits of the dynamic system and, on the other hand, the definition of a new metric that can properly describe the flexibility of the building systems with reference to the future scenarios analysed. This metric is based on six classes – which describe the statistical distribution of the energy consumptions of all the scenarios simulated in the matrix – and an index called Energy Flexibility Index (EFI) that quantifies the flexibility of the technology considered. The case study analysed highlights how implementing a dynamic shading system, considering the same building use, can increase the EFI of nearly 21% for non-optimized control strategy and up to 23% when optimized. While changing the building use in residential reduces these values respectively, to 6% and 7%. [ABSTRACT FROM AUTHOR]

• Climate change's impact on retrofitting was tested on Le Corbusier's apartment. • Climate change scenarios project up to 70% increase in summer overheating. • Adaptive natural ventilation can reduce warm discomfort of 50–60%. • Adaptive setpoints can reduce total energy consumption of 20–30%. • Adaptive strategies are particularly favourable in historic buildings. Historic buildings, often exempt from retrofits to preserve originality, require retrofitting due to potential future climate-related indoor issues. For Modern Architecture constructions, there is a need to find solutions that help address the discomfort and heat losses caused by the extensive use of glazing. By analysing Le Corbusier's studio-apartment this paper aims to inspect: (i) Solutions for energy, Indoor Environmental Quality, and preservation; (ii) Climate change impact on them; (iii) Possible adaptation strategies to cope with climate change. Spectrally selective glazing reduced summer overheating by 15%; high-performance glazing lowers cold discomfort (24%) and heating (22%) but increased warm discomfort; shadings maintained energy use and reduced summer discomfort by up to 44%; thermal insulation can reduce winter discomfort and halves energy use but raised summer discomfort by up to 41%. Tests on 2050–2100 climate change scenarios reveal up to 70% more warm discomfort hours. Adaptive strategies can help, with natural ventilation cutting warm discomfort by 50–60%, and adaptive setpoints reducing cooling demand by about 35%. Adaptive strategies can complement traditional retrofitting in addressing current and future climate conditions, especially in historic buildings that require minimal interventions to preserve their historical characteristics and enhance resilience. [ABSTRACT FROM AUTHOR]

The regional impact of climate change on heating and cooling demand is important to consider when designing optimal long-term energy policies. Several studies have addressed this issue, but either at a very aggregated level or without optimizing the whole energy system. The aims of this paper are to fill this gap in a generic way and to assess the impact of climate change on heating and cooling energy demands for residential and commercial sectors at the regional and nodal levels in the context of Chile's energy transition. We propose a methodology based on high resolution climate simulations for the Representative Concentration Pathways (RCP) RCP 2.6 and RCP 8.5 scenarios. First, a statistical analysis is performed to estimate the long-term trends of so-called heating and cooling degree-days and their impact on final regional energy demands. Then, demand pathways in the energy transition are assessed using a multi-sectoral energy planning model. Numerical experiments using data from Chile show an overall positive economic impact of climate change (limited to heating and cooling demands) for the energy system, with a significant decrease in heating demand compared to a limited increase in cooling requirements. For the RCP 8.5 scenario, cost reductions reach 2.1% of the total discounted system cost on the 2020-2050 period mainly due to a significant decrease of gas consumption for heating. This research highlights the importance for policymakers to consider climate change in efficient energy policies. [Display omitted] • Climate change impact on heating/cooling is assessed for Chile's energy transition. • Significant heating demand decrease and low cooling demand increase are observed. • A global positive economic impact for the energy system is estimated. • For the RCP 8.5 scenario, cost reductions reach 2.1% of the total discounted system cost. [ABSTRACT FROM AUTHOR]

Behaviour, practices and culture constitute a powerful human factor in the energy system; in particular the interactions between technologies, practices and norms lock individuals in to certain patterns of (often inefficient) energy use. Consequently, behaviour change has gained traction amongst policymakers as a key area of intervention given the impact energy-related behaviours have on climate change. Given the increasing emphasis within policy perspectives in the European Union, it is surprising that a gap in understanding of the success factors of behaviour change initiatives remains. This paper addresses this gap by identifying and characterising behaviour change initiatives across five European countries (the UK, Ireland, France, Italy, and Spain). The paper provides insights into the success factors and commonly encountered barriers to behaviour change initiatives. Initiatives are classified into 6 broad categories (community-based interventions; information and awareness based interventions; eco-districts; show-case events; energy switching; and smart-technology focused interventions). The results suggest that there are significant knowledge gaps between what is known to work to engage individuals in behavioural change and what is currently being applied in practice. An over-reliance on education and awareness-raising projects is evident, illustrating that such projects do not sufficiently aim for sustained behavioural changes. A dearth of projects incorporating fiscal measures, regulations or legislation to drive behaviour change reflects reluctance on behalf of decision-makers to engage widely with diverse approaches to foster lifestyle change. This paper contributes understandings of the different models and delivery tools employed to change energy-related behaviours; insights into the critical success factors that underpin best practice and the barriers to action; and a ‘what works in practice’ overview of the meaningful approaches to change behaviour. [ABSTRACT FROM AUTHOR]

Cities are suggested as being the key level for shifts towards more sustainable modes of production and consumption. The building sector with its significant carbon footprint plays an important role in urban climate change adaptation strategies. Using the case study of Brisbane (Australia), the paper examines the place-specific contextualisation of green building transitions by analysing the co-evolution and interplay of building practices, policy making and involved actors. Drawing on theoretical approaches of Transition Studies and Evolutionary Economic Geography, we trace back and analyse policy and economic trajectories focusing on formative and hindering processes. The paper discusses ambivalent pathways and 'regime resistance' caused by local economic and political specificities. The analysis illustrates how crucial the continual support from both policy makers and industry actors can be when economic market mechanisms do not drive sustainability transitions. Regime actors can play a powerful role as 'transition detractors' and can determine the dynamics and the scope of sustainability transitions. [ABSTRACT FROM AUTHOR]

This paper describes a method for residential water use modeling predicated on metered energy data. Actual measured hot water volumes for major indoor consumption are used to verify and adjust the outputs in gallons of hot water consumption based on climate variables, water heater technical features, and set-point and intake temperatures. Three independent datasets for residential energy (RECS 2009), water heater efficiency (Air-conditioning, Heating and Refrigeration Institute-AHRI), and end-use domestic water (Residential End Uses of Water, Version 2-REU II) are applied to identify specific demographic, built environment and geographic factors that relate patterns of energy demand to water consumption. The proposed model acts within the broader Integrated Urban Metabolism Analysis Tool (IUMAT), a system-based analytical framework for evaluating the environmental performance of the built environment. The method described in this paper offers an alternative approach to residential water consumption modeling by implementing volume of hot water consumption as a proxy for indoor water use. It provides utilities with the potential to parse and prioritize energy and water conservation measures. [ABSTRACT FROM AUTHOR]

• This paper systematically reviews the research progress of RS technology applied to various stages of PV system development. • We conclude that RS plays a significant role in PV potential assessment, large-scale data analysis and PV health monitoring. • We discuss future challenges and opportunities for RS technology in PV applications for advancing the research in this area. Developing solar photovoltaic (PV) systems is an effective way to address the problems of limited fossil fuel reserves, soaring world energy demand and global climate change. The earth observation information provides a promising perspective for estimating the PV energy potential and understanding the status of the PV system development, which is critical for making scientifically sound and cost-optimal sustainable planning strategies. Remote sensing (RS), a versatile technology that captures surface information at various temporal and spatial scales, is now widely applied in different fields of the PV development. However, despite the rapid growth of related research, there is still a lack of comprehensive review on the application of RS to different stages (i.e., planning, site selection, installation, maintenance, etc.) of the PV system development. This paper systematically reviews the research progress of RS technology applied throughout various stages of the PV system development. The reviewed literatures are organized as four major parts: i) PV potential estimation, ii) PV array detection, iii) PV fault monitoring and diagnosis, and iv) other cross-cutting areas where RS can facilitate PV development. We conclude that RS technology can bridge the gap caused by the traditional methods in effective assessment of resource potential, large-scale data analysis and PV health monitoring, which can provide strong support in assisting the planning, management, and decision-making of PV systems. Finally, we discuss future challenges and opportunities for RS technology in PV applications for advancing the research in this area. [ABSTRACT FROM AUTHOR]

The energy consumption necessary to maintain thermal comfort in buildings remains a significant and partially unjustified part, accounting for about 30–40% of the total energy consumption. Despite the increasingly pressing regulations in the energy sector (EPBD recast), the quality of the internal environment remains one of the critical parameters on which to pay more attention in view of a consistent evaluation of the Nzeb building. The windowed components are often designed with thermal insulation performances higher than the minimum requirements but still they lack in design of the incident solar radiation control, which is a particularly delicate topic for indoor comfort and more generally for a higher energy efficiency in buildings. If we think of the numerous variables of influence (typology, orientation, geographical location, etc.), the possibilities to associate energy saving, lighting control and users' comfort are inevitably entrusted to dynamic systems integrated into the glass. In this paper authors present the results related to the experimental characterization of two identical test rooms with different typologies of windows. One room is furnished with a traditional high thermal performance glass and the other, with an electrochromic glass suitably controlled by remote. The operative temperature measured in both test rooms have been utilized to verify the simulation model developed to assess the energy saving achievable in a Mediterranean climate, taking properly into account the hourly variations of the climate and the actions on the shading regulation systems. [ABSTRACT FROM AUTHOR]

Policies targeting energy efficiency and renewable energy are sometimes viewed as more politically feasible than carbon pricing in pursuit of emission reduction goals. This paper assesses underlying drivers of energy policy development. These factors include economic, social, environmental, and institutional variables. The between estimator for panel data is an appropriate method for our focus on some exogenous variables that vary more across countries than over time. We find that larger oil reserves per capita have a negative relationship with renewable energy policy development. Education and political globalisation have strong positive relationships with both energy-efficiency and renewable-energy policy development. These results suggest that greater participation in global political groups can be an indirect approach toward energy policy development, in cases where direct and immediate policies are hard to implement. OECD countries have higher policy scores by 33 and 25 points in energy efficiency and renewable energy respectively. Blinder-Oaxaca decomposition analysis shows that these higher scores are primarily due to social and political institution predictors rather than economics and physical endowments. • Large-n cross country international sample on continuous policy score measurement. • Political globalisation is positively linked with renewables and energy efficiency policies. • Education is positively linked to energy policy development, especially for efficiency. • Higher OECD countries' policy scores are primarily due to social and political predictors. • Higher incomes are unlikely to lead to automatic improvements in energy policies. [ABSTRACT FROM AUTHOR]

This paper presents new metrics to measure the effect of thermal mass on the energy required to heat and cool buildings. Previous studies have been flawed as they have not considered the interaction between intermittent occupancy and thermal mass, which has a significant impact on overall energy use. However, existing parameters do not adequately capture these effects, so the new metrics developed in this paper are used to analyse the impact of thermal mass in hot climates with active cooling, and cold climates with active heating. The results agree with existing literature that high thermal mass structures are likely to be effective in hot climates; however, in cold climates the drawbacks of high thermal mass likely outweigh the advantages, and high thermal mass can cause an increase in energy use. This finding has implications for the design of buildings in cold climates, and contradicts the commonly-held assumption that high thermal mass is correlated with low energy use. The new metrics (transient energy ratio and effective U -value) provide a generalisable method to quantify these effects. They are further used here to analyse the dynamic performance of heavily insulated buildings and show that high thermal mass often leads to higher energy use in cold climates. [ABSTRACT FROM AUTHOR]

South East Europe is the region in a part of Europe with approximately 65.5 million inhabitants, making up 8.9% of Europe’s total population. The countries concerned have distinct geographical features, various climates and significant differences in gross domestic product per capita, so the integration of their energy systems is considered to be a challenging task. Large differences between energy mixes, still largely dominated by fossil-fuel consumption, make this task even more demanding. This paper presents the transition steps to a 100% renewable energy system which need to be carried out until the year 2050 in order to achieve zero carbon energy society. Novelty of this paper compared to other papers with similar research goals is the assumed sustainable use of biomass in the 100% renewable energy system of the region considered. It is important to emphasize here that only the sustainable use of biomass can be considered carbon-neutral. The resulting biomass consumption of the model was 725.94 PJ for the entire region, which is in line with the biomass potential of the region. Modelling the zero-carbon energy system was carried out using the smart energy system concept, together with its main integration pillars, i.e. power-to-heat and power-to-gas technologies. The resulting power generation mix shows that a wide variety of energy sources need to be utilized and no single energy source has more than a 30% share, which also increases the security of supply. Wind turbines and photovoltaics are the main technologies with shares of 28.9% and 22.5%, followed by hydro power, concentrated solar power, biomass (mainly used in cogeneration units) and geothermal energy sources. To keep the biomass consumption within the sustainability limits, there is a need for some type of synthetic fuel in the transportation sector. Nevertheless, achieving 100% renewable energy system also promises to be financially beneficial, as the total calculated annual socio-economic cost of the region is approximately 20 billion euros lower in the year 2050 than in the base year. Finally, energy efficiency measures will play an important role in the transition to the zero-carbon energy society: the model shows that primary energy supply will be 50.9% lower than in the base year. [ABSTRACT FROM AUTHOR]

• Globally, population weighting substantially changes degree-days rate of change. • Choice of base temperature strongly influences degree-day calculation. • For typical base temperatures, heating degree-days are falling at twice the rate that cooling degree days are increasing. • Within countries, heterogeneity in population changes determines relative changes in heating and cooling degree-days. Anthropogenic greenhouse gas emissions are driving global increases in temperature. This rise will likely lead to an increase in demand for cooling in the coming years. However, increasing temperatures are not the main explanatory factor for why the world is moving towards more cooling. This paper compares population and area-weighted cooling and heating degree-days derived using ERA5-Land reanalysis temperature, to show that population growth in warmer parts of the world drives cooling demand globally. The analysis shows that mean global area-weighted heating degree-days have fallen 8.46 °C days/year, whereas population-weighted heating degree-days have fallen by 12.5 °C days/year. At the same time, mean global area-weighted cooling degree-days have risen by 3.0 °C days/year, while population-weighted cooling degree-days have risen at 6.0 °C days/year. By using sub-country analysis, this paper shows that population-weighted degree-days can substantially differ from area-weighted degree-days. Finally, the findings highlight that the choice of heating and cooling degree-day base temperature is the most important parameter in the variability of degree-days and will need to be understood better in order to accurately account for future heating and cooling energy demand. [ABSTRACT FROM AUTHOR]

Abstract China transport energy consumption grows greatly along with dramatically escalated carbon dioxide emissions. Saving energy in transportation is requested for both reducing energy pressure intensity and decreasing relevant emissions. Large scale energy conservation and emission reduction are Chinese automotive industrys' fundamental objectives. This paper addresses a nonlinear hybrid fuzzy based proportional integral derivative (PID) control methodology to reduce the automobile fuel over-consumption and gases over-emission. After introducing the mathematical model of the automobile Pierburg mechatronic actuator of nonlinear character with parameter uncertainties, its angular displacement is controlled via the proposed PID-fuzzy logic control (FLC) approach. The outputs of the PID controller are the entries of the series-connected FLC. The hybrid topology merges the simplicity and robustness advantages of both the classical PID and the FLC methods respectively. The feedback controller, based on FLC technique, is designed to desirably maintain the angular displacement towards their desired reference values with possible least steady state errors. The proper steady state error elimination will lead to considerable gas emission reduction together with improved energy efficiency. Through Matlab/Simulink tools, the numerical simulations significantly illustrate that the hybrid PID-FLC technique can contribute efficiently in ameliorating the system dynamic behavior in presence of parameter uncertainties. The overall system behavioral analysis enhancement and the proposed controller robustness are experimentally validated. [ABSTRACT FROM AUTHOR]

Abstract Cities, the core of the global climate change mitigation and strategic low-carbon development, are shelters to more than half of the world population and responsible for three quarters of global energy consumption and greenhouse gas (GHG). This special volume (SV) provides a platform that promotes multi- and inter- disciplinary analyses and discussions on the climate change mitigation for cities. All papers are divided into four themes, including GHG emission inventory and accounting, climate change and urban sectors, climate change and sustainable development, and strategies and mitigation action plans. First, this SV provides methods for constructing emission inventory from both production and consumption perspectives. These methods are useful to improve the comprehensiveness and accuracy of carbon accounting for international cities. Second, the climate change affects urban sectors from various aspects; simultaneously, GHG emissions caused by activities in urban sectors affect the climate system. This SV focuses on mitigation policies and assessment of energy, transport, construction, and service sectors. Third, climate change mitigation of cities is closely connected to urban sustainable development. This SV explores the relationships between climate change mitigation with urbanization, ecosystems, air pollution, and extreme events. Fourth, climate change mitigation policies can be divided into two categories: quantity-based mechanism (e.g., carbon emission trading) and price-based mechanism (e.g., carbon tax). This SV provides experiences of local climate change mitigation all over the world and proposes the city-to-city cooperation on climate change mitigation. [ABSTRACT FROM AUTHOR]

Highlights • Taiwanese building energy conservation index (ENVLOAD) was converted to OTTV. • New models for energy efficient envelope were proposed as an adaption to the changing climate. • Coefficients of the OTTV model should be changed to reflect climate change. • Thermal insulation is gaining more concern while climate change proceeds. • Altering method of OTTV and setting new criteria in response to future climate was proposed. Abstract Changes in the climate system affect a building's energy consumption. Many countries have implemented building energy consumption indices to regulate the newly built buildings from excessive energy use. However, those indices were developed based on previous climate datasets and were incapable of responding to the changing climate. To stabilize the energy uses of future buildings as those under today's climate, regular updates of the evaluation index are mandatory to take climatic variations into consideration. This study firstly discussed the limitations in responding to future climate of current practicing building envelope energy conservation index in Taiwan. Secondly, we proposed a new index, the overall thermal transfer value (OTTV), based on the simulation results and tried to convert existing baseline criteria for the new OTTV. An approach on how to alter the OTTV index in response to the climate change was proposed. We found that because of the warming climate, the coefficient of the OTTV equation has to be changed over times to accurately respond to the changing climate. The approach presented in this paper provides a method on how to formulate a climate responsive index in pursuit of a better energy efficient building in the future. [ABSTRACT FROM AUTHOR]

This paper investigates the climate change impact on cooling energy consumption of office buildings in four major architectural climate zones in China. The results show that there are apparent differences in the responses of monthly or yearly cooling loads to climatic change in different climates. Dominant factors affecting monthly cooling loads change from dry bulb temperature (DBT) to wet bulb temperature (WBT) with the climate zones changing from severe cold to hot. The yearly cooling load was mainly afftectd by DBT in severe cold climate, whereas the WBT had the dominant effect in the other climates. With the continuous warming climate, the yearly cooling load did not rise significantly for any climate zone except for severe cold climate zone where cooling load had a significant increase ( p  < 0.01). More importantly, the cooling load showed a weak decrease in Guangzhou. These results suggest that different measurements for buildings cooling energy conservation should be made in different climate zones. The humidity effect should be fully considered to improve buildings energy efficiency, especially in the hot climate zones. The continuous increase of temperature in the future does not necessarily increase cooling loads of buildings in the cold, hot summer & cold winter and hot summer & warm winter climate zones, and change trendency of humidity in the future need to be considered to predict cooling energy consumption. [ABSTRACT FROM AUTHOR]

The Chinese government committed to reduce its national CO 2 emissions intensity by 40–45% until 2020 in response to climate change. This paper quantitatively evaluates the performance of CO 2 emissions reduction over the period 2005–2020 from the historical and prospective perspectives by using a combination of decomposition analysis and scenario analysis, aiming to provide suggestions about how to achieve the target in key emissions reduction fields. Unlike traditional index decomposition methods, this paper incorporates the total energy conversion efficiency effect into the model, and further decomposes it into a final energy mix effect and a final energy conversion efficiency effect by a multilevel decomposition procedure, allowing to measure the contributions of primary energy structure low-carbonization, the final energy mix electrification, and the energy conversion efficiency improvement. The results show that the carbon intensity could decline over the period 2005–2020 by 47.8%, 50.9%, 48.0%, 44.5% and 47.5% in the Business as Usual, S1, S2, S3 and S4 scenarios, respectively. This shows that the 40–45% target is very likely to be achieved. The final energy intensity effect is always the most important driving factor, causing carbon intensity to decrease by 24.0% and 22.1%, again respectively, from 2005–2012 to 2012–2020. Moreover, the energy conversion effect was another major driver during 2005–2012. The Chinese government needs to make more efforts to adjust the industrial structure, which could cause carbon intensity to decrease by 3.6% during 2012–2020, and to adjust the primary energy mix, which could cause carbon intensity to decrease by 7.1% during 2012–2020. [ABSTRACT FROM AUTHOR]

The paper provides an overview of a part of research related to the analysis of information technologies and measures for improving the energy efficiency in urban planning that can contribute to mitigating the impact of climate change. The first part of the paper deals with problems supported by the numerous data on negative effects of climate change on the cities, such as urban heat islands, energy and ecological crisis. The second part of the paper proposes solutions that rely on information technologies which facilitate process of urban planning. Two projects related to the implementation of measures for improving the energy efficiency in urban planning were conducted within this research. The first one is considering the design of a spa centre in an undeveloped mountain landscape and the second one is dealing with reconstruction of a residential block in urban built environment. In the first case study, the proposed solutions rely on the information technologies, while in the second case study they rely on the implementation of measures for improving the energy efficiency in urban planning. The results show that the application of different measures in urban planning depends on the level of the built environment. [ABSTRACT FROM AUTHOR]

In response to the challenge of climate change, personal carbon trading was put forward as a policy instrument to promote low carbon behavior in the household sector. To evaluate the effectiveness of this scheme, it is important to gain insight into the allowance trading and energy consumption behavior in a long emission commitment period. This paper proposes a dynamic programming model to investigate allowance trading and energy consumption. A main feature of the model is its consideration of allowance banking and borrowing activities. Ten simulated scenarios with different allowance prices, price volatility and carbon emission rates are discussed. The findings show that consumers would trade more actively when allowance price is volatile. It is also found that energy consumption and allowance trading will decrease when the carbon emission rate increases. Overall the analysis in this paper implies that personal carbon trading scheme would be an effective policy measure to change consumers' behavior. Therefore it would be valuable for decision-makers to consider the introduction and implementation of this scheme. [ABSTRACT FROM AUTHOR]

The building sector is considered as the biggest single contributor to world energy consumption and greenhouse gas emissions. Therefore, a good understanding of the nature and structure of energy use in buildings is crucial for establishing the adequate future energy and climate change policies. Availability of the updated data is becoming increasingly important in order to allow a rigorous analysis. In this paper, recent data on the world energy consumption in both residential and commercial buildings are reported. Past situation, current status and future trends are discussed and analyzed for selected countries. A breakdown of buildings energy consumption is realized in order to determine the influencing key parameters. A whole section of this paper is dedicated to give an overview of measures and policies adopted by different countries, allowing the monitoring, management and reduction of the energy consumption in buildings. Critical aspects of these policies are discussed based on the feedback of the early adopters. [ABSTRACT FROM AUTHOR]

Global warming, climate change, and resource depletion have forced us to reconsider energy usage and efficiencies over the last few decades. Residential and commercial buildings are both large energy consumers, so improving energy and material usage efficiency in this sector is a common research topic. According to a recent study, the Building Sector (BS) accounts for 40% of greenhouse gas emissions. The primary objective of this paper is to examine and assess the potential of Renewable Energy Systems (RES) and their combinations for enhancing energy efficiency in the BS. Specifically, the focus will be on converting low energy-efficient buildings into highly efficient ones. The potential of the RES and their combinations for the BS is evaluated based on payback durations, energy generation, and reduction of CO 2 emissions. The optimization flow charts for the RES, feasibility studies, commercialization road maps of energy storage systems and the necessity of control mechanisms for enhancing RES efficiency were discussed. Additionally, the technology drawbacks are discussed, along with various innovative techniques recommended to direct future study in this area. Finally, this article assists the audience clear idea in the selection of the right combination of potential RES based on different conditions to achieve deep decarbonization in BSs. • Buildings sector (BS) responsible for 40% of GHG emissions. • Study assesses potential of Renewable Energy System (RES) in BS. • RES evaluated on payback, energy generation, and CO 2 reduction. • Optimization, feasibility and commercialization studies were discussed. • Article recommends right RES combinations for deep decarbonization in BS. [ABSTRACT FROM AUTHOR]

• Investigated climate change impacts on office building performance in Brussels. • Applied a long-term climate change sensitive system sizing and design approach. • Time-integrated discomfort analysis showed a major surge in overheating by 2100. • Long-term climate change resistivity is ensured in reference building until 2100. • Primary energy use and GHG emission findings are useful in mixed humid climates. As climate change continues, it is expected that the risk of overheating will rise in both new and existing buildings in mixed humid climate zones in Europe. This study introduced a novel climate change sensitive sizing and design approach for cooling and heating systems in nearly zero-energy office buildings in Brussels, Belgium, for different weather scenarios. This approach considered the long-term effects of climate change on building performance. The climate change effects were assessed using current and future climate data from the regional atmospheric model, MAR. To demonstrate the approach, a case study of a nearly zero-energy office building in Brussels was conducted. The reference building model was first calibrated using monthly energy use data from the year 2019 using ASHRAE Guideline 14. Then, the building was evaluated with different HVAC strategies and their performances were quantified. The results indicated an increase in overheating as high as 1.2 °C and cooling energy use as high as 13.5 kWh/m2 and a decrease in overcooling as low as 0.3 °C and heating energy use as low as 10.9 kWh/m2 in the reference building by the end of the century. In addition, due to climate change sensitive sizing and design approach coupled with optimal sizing, the reference building was climate change resistant towards the worst-case scenario by end of the century with up to 3.7 for climate change overheating resistivity and 20.2 for climate change overcooling resistivity. Finally, the paper provided recommendations for future practice and research based on the study findings. [ABSTRACT FROM AUTHOR]

Policies on bioeconomy are some of the key emerging ones around the world to support sustainability in terms of using renewable resources. However, these may lead to significant demand for biomass feedstock which relies on limited resources, viz., water, land, and energy. The impact of climate change on water availability makes it more challenging. This paper demonstrates the analysis of the water, energy, and food resource nexus of a bioeconomy-based industrial complex and future climate change impact. The model structure consists of cultivation, crop processing, and urban sectors. Sugarcane is the major crop in the case study area and is the main bioeconomy crop. The results indicate that the average sugarcane yield will be lower than the minimum industrial goal for the 2020s and 2030s decades. Consequently, sugarcane feedstock shortage may often occur. The drought situation tends to be increased, so groundwater resources can be the main reserve source of water. In all improvement scenarios on water supply management, nexus energy used for water acquisition was mainly for groundwater acquisition. Direct energy use in the cultivation process is high and fossil fuels based, while most of the energy used in processing came from biomass waste. This implies that technologies for water acquisition will be more important in the future and should be developed in terms of energy efficiency and the aspect of promoting the usage of renewable energy to reduce greenhouse gases and fossil fuels use. The impact of climate change will cause significant fluctuations in the annual rainfall characteristics of the study area. An additional irrigation water supply of about 250 mm and expansion to cover more than 90% of the cultivation area should be considered to secure the minimum supply of sugarcane for the local biorefinery complex in the following decades. [Display omitted] • Integrate climate change impact to Water-Food-Energy nexus model for bioeconomy. • The water–crop yield response model was set up to analyze interventions for improving yield. • In all scenarios, nexus energy used for water acquisition was mainly for groundwater acquisition. • The area will face a water supply shortage in the 2020s, and groundwater is the primary reserve source. • The irrigation expansion to cover 90% of the cultivation area can secure the supply of sugarcane. [ABSTRACT FROM AUTHOR]

Given the need to rein in the rise in the global average temperature, decarbonizing the electricity sector, which accounts for nearly 50% of global greenhouse gas (GHG) emissions, is crucial. The suitability of nuclear power as a base-load technology and its relatively negligible GHG emissions raised expectations of a nuclear renaissance, until the Fukushima disaster brought discussions about nuclear power’s potential to a standstill. However, completely ruling out nuclear may not be sustainable owing to the realities of rising energy demand, climate change considerations, and the need for reliable base-load supply technology, especially in the case of fast growing economies in the Association of South East Asian Nations (ASEAN). The Fukushima disaster was a wake-up call for both governments and the nuclear industry. Led by the International Atomic Energy Agency, the more advanced economies conducted stringent reviews of safety standards and emergency response procedures in the event of a catastrophe. Meanwhile the industry responded with strong commitments towards “Fukushima proof” designs, alongside other advancements towards “safer” fission power. In the ASEAN context, we argue in this paper that in addition to the economic advantage, nuclear power can help address the twin objectives of energy security and mitigating climate change effects. In ASEAN, there is still a strong momentum towards nuclear power development due to strategic considerations. In this paper, we reviewed in a holistic approach the various factors influencing decision making on nuclear power. Using ASEAN as a case study, we argue that nuclear power remains an important option and should be taken up rapidly if decarbonizing electricity generation is a grave concern. We also provide some recommendations towards the “safer nuclear” for ASEAN at the end of this paper. [ABSTRACT FROM AUTHOR]

Household fuel-use (HFU) patterns are strongly associated with multiple effects, including air quality, human health, and regional climate change. This paper presents the results from the first Chinese Environmental Exposure-Related Human Activity Patterns Survey (CEERHAPS), carried out among 91,121 households located in 9108 villages, 636 towns, and 159 counties in 31 provinces. Face-to-face interviews were conducted with each participant to obtain information about the type of fuels used for cooking and heating. The main objectives of this paper were to investigate HFU for cooking and heating in China, to validate the World Health Organization (WHO) model, and to help inform local evaluation models. In China, gas and biomass fuels, the dominant energy fuels for cooking, are used by 44.8% and 32.1% of households, respectively. Approximately 34.1% of families have no household heating during the cold season, and 16.7%, 15.6% and 12.8% of households rely on coal, electricity, and biomass, respectively, for household heating when no central heating was available. The proportion of households using solid fuels has generally decreased during the last two decades. Considerable spatial variation was evident in the HFU patterns for both cooking and heating. The data revealed that the predominant fuel for cooking was biomass (47.6%) in rural populations, whereas urban households were more likely to cook with gas (65.8%). In terms of heating, coal (21.4%) and biomass (19.0%) were the main fuels used in rural households, while electricity (23.6%) and coal (10.5%) were more commonly used in urban areas. The overall HFU results for cooking from this study were comparable to those predicted using the WHO model. We also developed models at the provincial level to estimate HFU for cooking and heating in China; it is expected that the model, if confirmed by future studies, could be used for future research on household air pollution, domestic human exposure and burden of disease. [ABSTRACT FROM AUTHOR]

Cities are mainly responsible for greenhouse gas (GHG) emissions in the atmosphere and thus for climate change. The European Union (EU) set up a series of strategies and policies to facilitate the elaboration of climate change mitigation and adaptation of urban plans. To do this, it is necessary to measure the city's GHG emission level. The Urban Carbon Footprint (UCF) and its derivation, the Relative Carbon Footprint (RCF), represent the most appropriate tools for obtaining this important information. The present paper applies these indicators to a small city (150 000 inhabitants) located in Southern Italy, a novelty for academic studies, which usually concentrate on megacities. The study focuses only on CO 2 emissions, as these represent 90% of the total GHGs released in urban areas. The findings showed that in 2015 the total UCF was equal to 288 ktCO 2 , specifically deriving from electricity and natural gas consumption. Moreover, Residential, Industry and Tertiary are the most carbon-intensive economic sectors. The RCF was equal to 0.30; the city emission levels were lower than the national average. Therefore, the municipality represents a typical “net-consumer” community, dominated by homes with territorial emissions due to consumption and characterized by a low number of industries and an average income per capita that is 50% lower than the national one. Starting from these results, the study proposed an urban action plan according to the EU mitigation and adaptation policies. This plan could help the local government improve its environmental sustainability, even if more public city-level data is required for a more comprehensive analysis. Finally, it would be more appropriate for all actions to be aligned under a unique policy process to seize the opportunity to link the various local intervention policies from different fields, taking into account their existing funding, tools, processes, and resources. Capitalizing on the adaptation/mitigation connection will allow municipalities to leverage their climate change action efforts and accelerate progress toward their climate and energy goals. [ABSTRACT FROM AUTHOR]

In order to achieve the targets underlined in the European Strategy for climate change and energy efficiency, the so called 20-20-20 package, the European Commission launched the Covenant of Mayors to endorse and support the efforts deployed by local authorities in the implementation of sustainable energy plans, and at the same time contribute to greenhouse gases emissions mitigation. This paper explores how the Covenant of Mayors (CoM) has been adopted in Portugal, and which type of measures are being defined and implemented by the municipalities. For that, all Sustainable Energy Action Plan (SEAP) submitted by Portuguese municipalities (124) have been examined, for which a detailed analysis was performed, including the Baseline Emission Inventory (70, i.e., around 50%). The municipalities that submitted SEAP cover 60% of the total population of the country because the main urban centres are a part of the 30% that have signed the CoM. Most common measures are related with changes on behaviour and infrastructure related to energy (such as renewable energies, energy efficiency in buildings, public lighting, etc.), waste and transport (for example optimization of: transport infrastructures, used vehicles and road operations). Public lighting is one of the energy measures present in all submitted SEAP, which plays a key role in energy consumption, reaching values of upwards of 12%, particularly in coastal areas due to higher population density and urban residential areas. Besides all efforts there is still a long way to go in terms of energy consumption reduction at local level. [ABSTRACT FROM AUTHOR]

The transition towards low-carbon economy requires a number of specific actions by a multiplicity of actors in order to reduce greenhouse gas (GHG) emissions, entailing energy efficiency, production of energy from renewable resources as well as the diffusion of more sustainable production and consumption patterns. Among the actors, local authorities can play a leading role for climate action. However, properly accounting for GHG emissions at local scale and identifying actions for GHG reduction are still an open challenge in many contexts. In this paper, we propose a method for GHG emissions accounting to support the identification of proper actions to achieve GHG reduction targets. The method widens the classical production-based approach to accounting, by proposing an extension of the accounting to three main areas: waste management and recycling, consumption patterns, and local land management. Life cycle thinking is applied as methodological basis for such extension. To illustrate the benefit of the proposed approach, the method has been applied to 16 municipalities (in Northern Italy), which were signatories of the Covenant of Mayors (CoM) initiative. CoM is a European initiative by which local authorities voluntarily commit to reduce their GHG emissions through the implementation of Sustainable Energy Action Plans. A comparison of the emission profile of the different municipalities helps identifying common patterns and local peculiarities to be addressed to achieve the reduction target. For the analysed case studies, the biggest contribution to GHG emissions comes from the consumption of the natural gas and electricity by the household sector. Emissions from waste generation play a minor role in the selected case studies. However, the inclusion of avoided emissions coming from waste recycling highlights the reduction potential if an appropriate waste management system is in place. Consumption patterns, as well, may play a relevant role. For example, assessing GHG emissions related to food consumption on top of those due to other drivers, the total municipal emissions change by increasing for an average of 22.6% for the selected case studies. Moreover, local land use planning and management should be included in the assessment, being crucial not only for the emissions uptake but also for climate mitigation and adaptation. The proposed approach to GHG accounting, including consumption-based aspects, may help identifying a wider set of climate actions to be implemented by local authorities to reduce environmental burdens. [ABSTRACT FROM AUTHOR]

This paper develops an Index of Sustainable Economic Welfare for Spain from 1970 to 2012 and seeks to update valuation approaches to a number of items. Two approaches have proven particularly controversial over recent decades; the costs of energy depletion and of climate change. The valuation implications in measuring present welfare have proven problematic, as both include future sustainability consequences arising from resource depletion and environmental impacts. This study includes a ‘ transition cost ’ approach to energy depletion, a modified approach to costs of climate change and water pollution, and removes the cost of ozone depletion. The results illustrate that while GDP per capita increased significantly, the ISEW per capita shows a widening gap. Household labour contributes strongly, but income distribution, energy depletion and costs of climate change limit improvement. Sensitivity analysis shows that accumulating climate change costs and escalating energy depletion costs have significant effects. Nevertheless, the new valuation approaches do not alter conclusions that welfare has shown little improvement. The ISEW provides a useful alternative to current indicators such as GDP subject to awareness of limitations. It is a measure of welfare that uses sustainability accounting methods when estimating costs, but is not an indicator of whether welfare is actually sustainable. [ABSTRACT FROM AUTHOR]

Over the recent decades, there has been an increasing focus on energy-efficient operation of vessels. It has become part of the political agenda, where regulation is the main driver, but the maritime industry itself has also been driven towards more energy-efficient operation of the vessels, due to increasing fuel costs. Improving the energy efficiency on board vessels is not only a technical issue - factors such as awareness of the problem, knowledge skills and motivation are also important parameters that must be considered. The paper shows how training in energy-efficient operation and awareness can affect the energy consumption of vessels. The study is based on navigational, full-mission simulator tests conducted at the International Maritime Academy SIMAC. A full-mission simulator is an image of the world allowing the students to obtain skills through learning-by-doing in a safe environment. Human factors and technical issues were included and the test sessions consisted of a combination of practical simulator exercises and reflection workshops. The result of the simulator tests showed that a combination of installing technical equipment and raising awareness - making room for reflections-on and in-action - has a positive effect on energy consumption. The participants, on average, saved approximately 10% in fuel. [ABSTRACT FROM AUTHOR]

In response to concerns related to climate change, and an attempt to encourage more sustainable behavior, individuals are often provided with information on greenhouse gas emissions (GHGs) of consumer items, such as personal vehicles. Currently in the US, information on vehicle efficiency is provided as grams of carbon dioxide (CO 2 ) per mile. Previous research presenting CO 2 as a mass and testing willingness-to-pay through Discrete Choice Experiment has found that such information can influence vehicle choice. However, other research has questioned whether how this information is presented might affect choice. That research argues that CO 2 emission information generally lacks contextualization that allows for interpretation. As well, it argues that the type of contextualization may affect choices. That research though did not test willingness-to-pay and the strength of its influence is not clear. In addition, research exists that argues that using pro-social, as opposed to financial, contextualization might be more influential on people’s choices. Thus, the purpose of this paper is to build on these previous findings on how CO 2 emissions are presented to determine whether changing how that information impacts vehicle choice with a Discrete Choice Experiment of vehicle choice analyzed using latent class modeling. No previous study has so robustly studied the influence that different framings might have on vehicle purchase. Five different methods of presenting CO 2 information are tested in this experiment: CO 2 emissions as grams per mile (current method), CO 2 emissions as pounds per year (consistent imperial units), CO 2 emissions as tons per year (yearly contextualization), an annual tax on CO 2 (yearly financial contextualization), and CO 2 as a percentage of the 2025 US EPA reduction target of 26% from 2005 levels (social goal contextualization). Results demonstrate that the current method results in lowest willingness to pay for CO 2 emission reductions, while the social goal contextualization results in the highest. [ABSTRACT FROM AUTHOR]

Climate change, environmental problems and consequent ecological damages due to excessive consumption of resources and to the continuing human population growth of more than 80,000,000 net increase per year, have damaged and continue to accelerate the devastation of numerous ecosystems. These changes have brought significant harm to humans and are imposing high costs on societal maintenance and development. In that context, low/no-fossil carbon transformations and improved material’s and energy efficiency are crucial elements for reconciling human activities with sustainable societal development, which is built upon vibrant and sustainable ecosystems. The urgently needed changes are bound to be difficult to make due to the perceived contradictions between low/no-fossil-carbon systems and sustainable and economically vibrant societies. This Special Volume (SV) is comprised of thirty-three articles, which mainly focus on investigations of low/no-fossil carbon transformations in countries, regions, industries and enterprises. Some authors provided insights of ways to proceed based upon new research and development (R&D), evaluations of specific low/no-fossil carbon technologies and lessons learned from policy simulations and analyses of potential post-fossil carbon societies. This SV introductory article contains an overview of the content of the articles divided into five topics: (a) low/no-fossil carbon transformations within industrial sectors, (b) regional planning and low/no-fossil carbon developments, (c) multi-regional, low/no-fossil carbon economies, (d) specific low-fossil carbon technologies, and (e) low/no-fossil carbon policy results. Given the extensive coverage of low/no-fossil carbon transformations, the papers on mechanisms and pathways are clearly the most important contributions of this SV. The researchers focused broadly on ways to address two objectives: (a) To characterize the main factors catalyzing high-fossil carbon development and (b) To accelerate the transition to low/no fossil carbon societies. Some authors focused upon new, low/no-fossil carbon development and planning in different countries and regions, while others focused upon ways to make changes within energy-intensive industries. Additionally, some authors reported on progress in the evaluation of the effectiveness of specific low/no-fossil-carbon technologies and in the design and implementation of low/no-fossil carbon policies. The findings and recommendations of the authors are positive and encouraging. However, it is clear, that there are many additional research, policy and educational challenges, which must be solved, to establish and support systems to guide and to monitor the transformations to sustainable, equitable, livable, low/post-fossil carbon societies. Much work remains but the wisdom in the articles in this SV will help societies make the needed transitions. [ABSTRACT FROM AUTHOR]

Water and energy are substantial mediums which allow to gain comfort and civilization development. Recently, humanity is facing a water scarcity problem as well as an energy crisis. Those factors forced to looking for alternative water sources and low energy solutions. In this paper water treatment technologies methods were described. Energy demand and cost of particular methods were analyzed. It was shown that conventional methods like coagulation and sedimentation are characterized by quite low energy demand. Whereas more advanced membrane techniques consumed much more energy. On the other hand they were able to obtain high removal efficiencies. It was noted that the most energy-intensive stage during water treatment was pumping. Whereas energy for performing purification stated only about a few percent of total energy demand. One of the newest approaches in water treatment is using renewable energy sources like wind, solar radiation or geothermal energy. It allows to decrease water treatment costs as well as reduces greenhouse gasses emission (expressed as carbon footprint). During designing water treatment plants water increase in water and energy demand supposed to be considered. • Observed climate changes lead to problems with access to fresh water. • Energy crisis forces searching for low-emission water treatment processes. • In future water treatment costs should consider costs of adaptation to climate change. [ABSTRACT FROM AUTHOR]

Accurately understanding the real situation of China’s carbon emissions at the provincial level is not only crucial for realizing carbon mitigation in China, but also of great importance for tackling climate change on a global scale. This paper uses detailed energy consumption data subdivided within each fuel type and sector-specific emission factors, to calculate both direct and indirect energy-related CO 2 emissions for China’s provinces, and offers provincially-targeted policy proposals on emission reductions. The results uncover large divergences in calculation of provincial CO 2 emissions between production-based and consumption-based accounting approaches. Considering the large amount of interprovincial CO 2 emission transfers embodied in secondary energy deployment, the consumption-based accounting performs better in reflecting the actual features and responsibilities of carbon emissions in the provinces of China. From the consumption perspective, Shandong, Hebei, Jiangsu, Inner Mongolia, Guangdong, Henan, Liaoning and Shanxi contributed to the majority of China’s carbon emission growth during the period of 1996–2013, while Xinjiang, Sichuan, Anhui, Tianjin and Hunan were playing an increasingly important role. These two groups of provinces should be regarded as the key regions for national emissions abatement. Meanwhile, the energy industry was the top sectoral contributor to CO 2 emissions growth in most provinces, while service and household sectors made increasingly significant impacts on driving up provincial emissions. Together with ongoing efforts in the energy sector, the mitigation of CO 2 emissions in service and household sectors deserves much more attention, especially in the transportation and urban household sectors. Furthermore, the temporal trends of carbon emissions in various provinces, as well as their factor and sectoral driving forces, varied greatly with each other. Therefore, each of the provinces should formulate emission reduction policies according to their own situation, and target the key driving factors and sectors of carbon emissions at the current stage or in the near future. [ABSTRACT FROM AUTHOR]

The project “Winter Model” started at the beginning of the 2000s. The idea was to try and predict the consequences of different winter maintenance strategies and to calculate the associated socio-economic costs. It is now possible to calculate and validate the impact that different winter maintenance measures have on road users, road authorities and local communities. This paper contains results of the first complete Winter Model calculations using existing conditions. Comparisons with different road classification standards have been carried out in order to determine the effect they have on socio-economic costs. Road classification standards dictate how much snow should fall before a maintenance action is initiated and how long it should take until the action is completed. Socio-economic costs increased for all comparisons when reductions in the classification standard were applied. As an example of how costs can vary: the scenario is a salted road using a combined plough and salt spreader where the allowed time to complete the action is 4 h that is changed to an unsalted road with an allowed time to complete the action of 5 h. Both scenarios have an action start criteria of 2 cm deep snow, and an annual average daily traffic flow of 2000. Comparison results show that the change from salted to unsalted road saves the most cost due to a reduction in salt use and required actions. However, the increased time to complete the action will result in slightly longer travel times and accident costs will increase by 24.2%. The extended action hour affect fuel consumption in a positive way, for example, consumption decreases slightly due to driving more often at lower speeds on unclear roads. By lowering the road classification standard like in this example, total socio-economic costs increased by 3.5%. [ABSTRACT FROM AUTHOR]

Rapid urbanization has exerted substantial pressure on China’s energy system and contributed to climate change. To find the key drivers of urban residential energy consumption and CO 2 emissions, this paper uses an extended Stochastic Impacts by Regression on Population, Affluence and Technology (STIRPAT) model that employs city-level data to examine the influences of population scale, income level, population compactness and price on house-based residential energy consumption, energy-related CO 2 emissions and private vehicle ownership. The empirical results indicate that factors such as population scale, affluence, and population compactness can lead to increases in residential energy consumption and CO 2 emissions. In terms of transportation, income and population scale positively drive the growth of private vehicle ownership, while the fuel price negatively influences private vehicle ownership. Moreover, population scale is the most important factor in residential energy consumption and CO 2 emissions. Finally, policy recommendations are suggested for China’s urban development strategy and urban design and to encourage technology innovations that reduce residential energy consumption and CO 2 emissions. [ABSTRACT FROM AUTHOR]

Climate change which is induced from energy consumption and CO 2 emissions has got people's attention; hence, many strategies and ways are being adopted to mitigate CO 2 emissions. Energy substitution is crucial to the promotion of energy conservation and CO 2 emissions reduction. The purpose of this paper is to estimate both inter-factor and inter-fuel substitution in China's iron & steel industry during the period 1985–2011. Empirical results show several conclusions for China's iron & steel industry: (1) own-price elasticity of energy is negative, so increase in energy price will reduce energy input; (2) energy and capital, and energy and labor are substitutes, and the substitution in energy/capital is relatively stronger; (3) though coal, oil and electricity are also substitutes, the substitution effect is not so obvious because of pricing distortions in China. The driving forces of energy efficiency change are further discussed and the results show that technology progress is the key factor determining energy intensity. Therefore, market-oriented reforms in terms of energy prices, improvement in energy substitution (including inter-factor and inter-fuel substation) and promotion of energy saving technologies are important means for ensuring future energy conservation and CO 2 emissions reduction practices in China's iron & steel sector. [ABSTRACT FROM AUTHOR]

[Display omitted] • A method for spatiotemporal coordination of multienergy systems is proposed. • Virtual energy storage gain is calculated based on spectral analysis. • The hydropower regulation ability affects the virtual energy storage gain. • The optimal coordination range between multiple energy sources is obtained. Utilizing the spatial heterogeneity and climate periodicity of various available renewable energy sources can enhance the multienergy complementarity, which will further reduce the energy storage demand and contributes to the "virtual energy storage gain." In this paper, we propose a spatiotemporal coordination method based on spectral analysis for a wind-PV-hydropower system that targets the maximum virtual energy storage gain. The complementary effect of hydropower on wind and PV power can be seen as changes in the regulation ability resulting from the hydropower construction development as well as a decreased variance in the total system production output. This method is used to determine the optimal coordination distance of multiple energy sources that are matched over different periods representing typical climate variation. A case study in the Yalong River basin in China obtains the best range of hydropower bundling surrounding wind power and PV power stations under different hydropower construction planning scenarios, and it reveals that increased regulation capacity of hydropower will reduce the optimal coordination distance but can achieve more energy balance if both actual storage and virtual storage is accounted for. This approach can realize energy delivery with the optimal coordination distance to meet intensive and efficient development needs, which can provide guidance and support for the planning and construction of wind-PV-hydropower storage systems. [ABSTRACT FROM AUTHOR]

Strict energy performance requirements have reduced the building's operational energy use and related environmental impact in the past decades. Consequently, the embodied impacts of buildings gained importance, and hence focussing on the life cycle impacts has become essential to further reduce the environmental impact of buildings. Life cycle assessment (LCA) is an internationally accepted method used for this purpose. Current LCA studies of buildings typically look at their whole life cycle but ignore potential changes in operational energy use due to climate change. However, the latter is expected to influence the operational energy use of buildings to a significant extent. This paper aims to improve the assessment of the operational phase by including variations in the yearly operational energy use caused by climate change and expected changes in the electricity mix as a strategy for climate change mitigation. This adapted dynamic assessment method is used to assess a Belgian office building. The results indicate that a Representative Concentration Pathway (RCP) 8.5 climate change scenario causes a decrease of 18 % for the end use of gas for heating and an increase of 32.4 % for the electricity use for cooling and ventilation. For the case study, the reduction of the environmental impact due to the decrease in gas use compensates the impact increase due to the higher electricity use. An increase in environmental impact in future would however occur if both heating and cooling are provided by electricity. Furthermore, depending on the changes that will occur in the electricity mix, the global warming potential of the office building will change by −13 % for an electricity mix dominated by renewables and by + 10 % for one with mainly production by gas compared to the situation with the current mix. However, the inclusion of a more extended list of environmental indicators shows that the overall environmental impact will only reduce by 4 % or even increase by 7 % compared to the situation with the current mix. [ABSTRACT FROM AUTHOR]

In this paper we address the problem of designing new energy-efficient static daylight devices that will surround the external windows of a residential building in Madrid. Shading devices can in fact largely influence solar gains in a building and improve thermal and lighting comforts by selectively intercepting the solar radiation and by reducing the undesirable glare. A proper shading device can therefore significantly increase the thermal performance of a building by reducing its energy demand in different climate conditions. In order to identify the set of optimal shading devices that allow a low energy consumption of the dwelling while maintaining high levels of thermal and lighting comfort for the inhabitants we derive a multi-objective optimization methodology based on Harmony Search and Pareto front approaches. The results show that the multi-objective approach here proposed is an effective procedure in designing energy efficient shading devices when a large set of conflicting objectives characterizes the performance of the proposed solutions. [ABSTRACT FROM AUTHOR]

Addressing climate change requires the efforts of all countries with common but differentiated responsibilities. The mitigation responsibilities one country takes greatly depends on its national emission inventories. As a good complement to the production-based accounting (PBA) principle, consumption-based accounting (CBA) principle has been widely concerned. However, few studies focus on emissions equity issues temporally and spatially. In this paper, we explore the characteristics of production-based and consumption-based CO 2 emissions for 14 major economies through multiple-dimension comparisons to get insight into the emissions equity comparisons among major emitters. In particular, four categories of economies with different dynamic features are divided based on their percentage differences between PBA and CBA emissions. Demographical and economic variables are additionally taken into consideration. The results indicate that France and Russia hold extreme characteristic on evaluating the emission difference between two principles, while China and Chinese Taiwan reveal uniquely increasingly larger gaps between two principle emissions. Besides, the per capita CBA emissions grows more prominently and possesses a more obviously positive correlation with their own per capita GDP which confirms that CBA principle is potentially attractive for estimating national emissions. [ABSTRACT FROM AUTHOR]