Search

The Circular Electron Positron Collider (CEPC) is a proposing electron–positron collider in China, which aims for generating high center-of-mass energy colliding above 250 GeV. The high-granularity electromagnetic calorimeter (ECAL) is included in a calorimeter system, which is mainly responsible for the measurement of photon. A particle flow algorithm (PFA)-based ECAL solution will utilize about 400k channels/m3. Here, we present the design and development status of readout electronics based on SPIROC2b for the CEPC ECAL with high-granularity scintillants and silicon photomultipliers (SiPMs). The readout electronics consists of front-end electronics (FEE), data interface (DIF) board, and data acquisition (DAQ) board. The front-end board (FEB) carries SiPMs (S12571-010P), scintillants (PSD), and FEB application-specific integrated circuit (ASIC) (SPIROC2b). Two electronics were designed in this paper, one is for ASIC functionality and performance only, and the other is used as a single layer of a further prototype of ECAL. Electronic test and cosmic ray test have been done to electronics. The results indicate that a charge dynamic from 62 fC to 300 pC at S/N = 2 is successfully achieved, and the minimum ionizing particles (MIPs) are separated from the pedestal. [ABSTRACT FROM AUTHOR]

In China, two modular multilevel converter (MMC) projects were recently commissioned, and another two are currently under construction. The real-time hardware-in-the-loop (HIL) test bench played an important role in validating the manufacturer's controllers. The full detail MMC model does not fit with the HIL test bench, which has to solve the circuit containing numerous switches and handles a large amount of inputs and outputs at a small time step for real-time simulation. The main challenge is to find a method to model and simulate the MMC systems with sufficient detail, accuracy, and speed. This paper presents an equivalent circuit method for the HIL test bench. The circuit inside the submodule is represented by mathematical equations, implemented in CPU or a field-programmable gate array, and solved in parallel to achieve real-time performance. This method-based test bench is used in those MMC projects in China and connected to the manufacturer's controllers for HIL tests. The model accuracy and simulation speed achieved by this method met the requirements of the HIL tests. In this paper, various scenarios are tested in an MMC HVDC study system. The results achieved by the proposed method have high agreement with those of a reference model in EMTP-RV. [ABSTRACT FROM PUBLISHER]

The ?1100 kV UHVDC wall bushing is the important power equipment in the ?1100 kV DC power transmission project of China. However, the reported literatures rarely mention its design method and the optimization of its insulation structure. In this paper, two specific designing schemes including the resin impregnated paper (RIP) condenser and the metalshielded core have been both adopted in the design of the wall bushing. Moreover, the actual operating environment and the rated parameters of the ?1100 kV UHVDC wall bushing have been analyzed in detail. Then, the nonlinear finite element method (FEM) analysis has been applied in the three-dimensional electric stress simulation of the UHVDC wall bushing. The electric field and temperature dependencies of the composite insulation used in the wall bushing have been taken into account. The E-field simulation results indicate that with the RIP condenser, the potential and electric field distribution can be much more uniform along the composite insulator of the bushing. Therefore, the compact design of the wall bushing can be obtained by this designing scheme. On the other hand, with the type of the metal-shielded core, the high E-field strength areas are mainly concentrated on the metal shield and the outer grading ring of the wall bushing. Therefore, the nonlinear FEM was applied in the structure optimization of the internal metal-shielded system used in the wall bushing. Finally, the maximum E-field strength of the wall bushing can meet the control requirement. Based on the simulation results and the optimization structure, the ?660 kV scaled prototype of the UHVDC wall bushing has been produced and passed through all the type tests according to the IEC 62199. The feasibility of the design of the ?1100 kV UHVDC wall bushing has been verified. This paper can provide the theoretical guidelines for the design, manufacture and operation of the UHVDC wall bushing. [ABSTRACT FROM AUTHOR]

A quasi-continuous high magnetic field is a special kind of pulsed magnetic field with a flat-top field longer than 100 ms. This paper proposes a hybrid power supply that consists of a capacitor power supply and a generator-rectifier power supply. A dual-coil magnet is powered to generate a 65 T/100 ms quasicontinuous high magnetic field with a ripple less than 500 ppm at the Wuhan National High Magnetic Field Center, Wuhan, China. A protection circuit consists of an R-C branch and a diode array is discussed for the worst short-circuit fault, which occurs between the first turns of inner coil and outer coil. This type of faultwill produce oscillation voltage with a high peak value and high frequency on the rectifiers. A self-adaptive PI controller with the coefficients corrected by a back propagation neural network is adopted to reduce the ripple of a flat-top. [ABSTRACT FROM AUTHOR]