Search

The combination of the time-scaling transformation and control parameterization has proven to be an effective approach in addressing optimal control problems involving switching systems with predefined subsystem sequences. However, this approach has certain limitations. First, the number of control switchings is required to be no less than the number of subsystem switchings. Second, the switching of the subsystem must be accompanied by the switching of the control. Third, this scheme introduces many hyperparameters, leading to combinatorial explosion. To address these drawbacks, we introduce a novel computational approach such that the control switching can be independent of subsystem switching. The superiority of this novel approach can be clearly observed from the solutions obtained using the proposed method for solving two illustrative examples. [ABSTRACT FROM AUTHOR]

In this paper, we consider a class of optimal control problems governed by nonlinear time-delay switched systems, in which the system parameters and switching times between different subsystems are decision variables to be optimized. We propose a new computational approach to deal with the computational difficulties caused by variable switching times. The original time-delay switched system is firstly transformed into an equivalent switched system defined on a new time horizon where the switching times are fixed, but each of the subsystems contain a variable time-delay that depends on the durations of each sub-system in the original system. By deriving the analytical form for the variable time-delay in the new time horizon, we can solve the new time-delay switched system. Then, gradient-based optimization algorithm can be applied to solve the equivalent problem efficiently. Numerical results show that this new approach is effective. [ABSTRACT FROM AUTHOR]

The control parameterization method used together with time-scaling transformation is an effective approach to transform optimal control problems into optimal parameter selection problems. The approximate problems can then be solved by gradient-based optimization methods. However, the conventional time-scaling transformation requires that all the control component functions switch simultaneously, which can be undesirable in practice. In this paper, we introduce a novel technique where the switching times for each of the control component functions can be adaptively selected. To demonstrate the effectiveness and flexibility of the proposed approach, two example problems with control input and terminal state constraints are solved using the method proposed. Numerical results show that the new method achieves much better objective values with some increase in computation time compared to the conventional time-scaling transformation technique. [ABSTRACT FROM AUTHOR]

Abstract The control parameterization method used together with the time-scaling transformation is an effective approach to approximating optimal control problems into optimal parameter selection problems when no time delays are involved. The approximate problems can then be solved by gradient-based optimization algorithms. However, the time-scaling transformation, which works well for optimizing variable switching times of the approximate piecewise constant/linear control functions obtained after the application of the control parameterization method, is not applicable to optimal control problems with time delays. In this paper, we consider a class of nonlinear optimal control problems with multiple time delays subject to canonical equality and inequality constraints. Our aim is to develop a novel transformation procedure that converts a given time-delay system into an equivalent system – defined on a new time horizon – in which the control switching times are fixed, but the dynamic system contains multiple variable time delays expressed in terms of the durations between the switching times for each of the approximate control functions in the original time horizon. On this basis, we show that an optimal control policy for the equivalent system can be obtained efficiently using gradient-based optimization techniques. This optimal control policy can then be used to determine the optimal switching times and optimal control variables for the original system. We conclude the paper by solving two example problems. [ABSTRACT FROM AUTHOR]

This paper considers the three-dimensional path planning problem for horizontal oil wells. The decision variables in this problem are the curvature, tool-face angle and switching points for each turn segment in the path, and the optimization objective is to minimize the path length and target error. The optimal curvatures, tool-face angles and switching points can be readily determined using existing gradient-based dynamic optimization techniques. However, in a real drilling process, the actual curvatures and tool-face angles will inevitably deviate from the planned optimal values, thus causing an unexpected increase in the target error. This is a critical challenge that must be overcome for successful practical implementation. Accordingly, this paper introduces a sensitivity function that measures the rate of change in the target error with respect to the curvature and tool-face angle of each turn segment. Based on the sensitivity function, we propose a new optimization problem in which the switching points are adjusted to minimize target error sensitivity subject to continuous state inequality constraints arising from engineering specifications, and an additional constraint specifying the maximum allowable increase in the path length from the optimal value. Our main result shows that the sensitivity function can be evaluated by solving a set of auxiliary dynamic systems. By combining this result with the well-known time-scaling transformation, we obtain an equivalent transformed problem that can be solved using standard nonlinear programming algorithms. Finally, the paper concludes with a numerical example involving a practical path planning problem for a Ci-16-Cp146 well. [ABSTRACT FROM AUTHOR]