Search

[Display omitted] • The LCA methods and findings of 41 papers on air-conditioning systems are examined. • Retrieved studies presented discrepancies in the LCA goals and scope definition. • The global warming potential (GWP) was the most evaluated indicator across papers. • Grid-connected electrical heat pumps generally had a higher life cycle GWP. • Improvements related to AC energy sources and other life cycle aspects are proposed. Air conditioning (AC) has become the fastest-growing energy end-use in buildings worldwide, and its adoption is expected to increase further due to various socioeconomic factors and climate change. Despite this, the decarbonization of space cooling is progressing slowly; hence, the emissions burden at each stage should be examined in detail. Given this context, it is crucial to assess the environmental performance of AC systems by considering a comprehensive approach like the Life Cycle Assessment (LCA). While several studies have already targeted the LCA of AC systems, a clear overview of those studies' methodologies, assumptions, and results is still lacking. Therefore, this systematic review examined the methods and key findings of 41 peer-reviewed articles. Although the results revealed discrepancies among the goals and scope, impact assessment methods, and indicators, most articles predominantly focused on the global warming potential (GWP) impact, and its reported quantification was further analyzed. It was observed that grid-connected vapor-compression heat pumps/chillers (conventional systems) presented higher GWP impacts than other AC systems powered by renewables, which in contrast, exhibited higher impacts in some toxicity and resource depletion-related indicators. However, the share of GWP showed different distributions, as the pre-operation emissions of solar-powered AC systems (either PV or thermal) were higher than those of conventional systems, mainly driven by reduced energy consumption usage. This review concludes with some recommendations for each stage of the life cycle. Since the operation phase generally showed the highest impact, more efforts should be devoted to accelerating the transition to a 100% clean electricity power system at a national scale. In contrast, the need to power AC systems with on-site renewables should be carefully assessed based on the context. [ABSTRACT FROM AUTHOR]

The thermal management system (TMS) in electric vehicles (EVs) is a comprehensive system that integrates an air conditioning system for the cabin, a temperature control system for the battery, and a cooling system for the motor. The currently used PI control strategy can only meet the basic TMS functions and cause high energy consumption. In this paper, we present a novel model predictive control (MPC) strategy for the TMS to optimize operational performance in real time. Different from the independent PI control for the individual components, MPC can predict future operation conditions and provide the optimal operating inputs in advance. A complete control-oriented model for MPC is developed, and the MPC strategy is designed to minimize the total power consumption of the TMS under the control-oriented model and constraints. The evaluation is carried out under several cases including the fixed ambient temperature, realistic ambient temperature, and different vehicle speeds. The results showed that the novel MPC strategy saved energy consumption by 5.9%–10.3% in these cases when compared to the PI strategy, demonstrating the effectiveness and feasibility of the proposed MPC control. • Proposed a model predictive control strategy for thermal management systems in EVs. • Developed a control-oriented model based on data-driven methods and physical principles. • Minimizes total power consumption while maintaining cabin and battery temperatures. • Results demonstrate the effectiveness of the MPC strategy under various conditions. [ABSTRACT FROM AUTHOR]

Highlights • EnergyPlus is capable of accurately estimating the heat transfer in parked vehicles. • Spectrally selective glazing can cause an average temperature difference inside the cabin as high as 12.5 °C. • Solar-reflective opaque coating in combination with ChLC glazing can reduce the cabin air temperature up to 23.8 °C. Abstract Parked vehicles have the tendency to overheat quickly. This can lead to a negative impact on the thermal comfort of the driver and its passengers, as well as intensive use of air conditioning systems, and thus fuel consumption of the vehicle or, in the case of electric mobility, a reduced cruising range. In the search for effective measures to mitigate this effect, important guidance can be provided by the field of sustainable building design. On the one hand, inspiration can come from design strategies in terms of shapes and advanced cover materials, but this paper advocates that this can also pertain to the simulation-based design support tools that are used by building engineers. This paper first presents the results of a thermal soak test, and then uses this data to demonstrate the suitability of the building performance simulation tool EnergyPlus for predicting the thermal behavior of parked vehicles. This fit-for-purpose validated model is used to evaluate the performance of three overheating mitigation measures for two car models in two climates. The results show that spectrally selective glazing can reduce the cabin air temperature by 12.5 °C and when combined with solar reflective opaque surfaces, the reduction of cabin air temperature can reach 23.8 °C. Increased use of building performance simulation in the automotive domain can help to further optimize the overheating reduction potential of cars. [ABSTRACT FROM AUTHOR]

Highlights • One-stop archive for developments in solid desiccant coated heat exchangers (DCHEs). • Comprehensive study on the selection of desiccants and binders. • Thorough analysis on the effect of operating parameters on dynamic performance. • Detailed review of advances in mathematical modeling of DCHEs. • Discussion on the potential system-level applications of DCHEs. Abstract Rapid urbanization and higher thermal comfort requirements have sharply increased buildings' energy demands. In tropical countries, for achieving energy efficient air-conditioning, desiccant dehumidifiers, which decouple sensible and latent load, are essential. While fixed-bed and rotary wheel desiccant dehumidifiers suffer from reduced adsorption capacity and lowered heat transfer efficiencies, desiccant coated heat exchanger (DCHE) system is a promising technology that can improve the energy efficiency of the standard vapor-compression air conditioners. Moreover, DCHEs also have prospective benefits in heat pump, adsorption chiller, and atmospheric water harvesting applications. In this paper, the advantages of DCHEs over other dehumidifiers are established, and a comprehensive review of various desiccant materials and binders used in DCHEs is carried out. The possibilities of using advanced materials to achieve superior energy efficiencies are also underlined. Different methods of coating the desiccant on heat exchangers are described, and quantitative parameters required to analyze the performance of the system are presented. Operating parameters affecting the dehumidification and thermal performance are identified, and the effect of their variation on the dynamic behavior of DCHEs is elaborately studied. The significance of using mathematical models as design tools is recognized, and the underlying assumptions, applicability, and limitations of the models for simulating the complex heat and mass transfer phenomenon are highlighted. The possibility of integrating an additional heat transfer equipment such as sensible heat exchangers, heat recovery devices, solar evacuated tube collectors, cooling towers, and evaporative coolers with DCHE is also presented. Finally, the potential system-level applications of DCHEs as heat pumps, adsorption chillers, water harvesters, and standalone air-conditioners are assessed. This review paper provides an update on recent developments in desiccant dehumidification and is intended to be a "one-stop" archive of known practical solutions that DCHEs can offer. [ABSTRACT FROM AUTHOR]

This paper describes a method for residential water use modeling predicated on metered energy data. Actual measured hot water volumes for major indoor consumption are used to verify and adjust the outputs in gallons of hot water consumption based on climate variables, water heater technical features, and set-point and intake temperatures. Three independent datasets for residential energy (RECS 2009), water heater efficiency (Air-conditioning, Heating and Refrigeration Institute-AHRI), and end-use domestic water (Residential End Uses of Water, Version 2-REU II) are applied to identify specific demographic, built environment and geographic factors that relate patterns of energy demand to water consumption. The proposed model acts within the broader Integrated Urban Metabolism Analysis Tool (IUMAT), a system-based analytical framework for evaluating the environmental performance of the built environment. The method described in this paper offers an alternative approach to residential water consumption modeling by implementing volume of hot water consumption as a proxy for indoor water use. It provides utilities with the potential to parse and prioritize energy and water conservation measures. [ABSTRACT FROM AUTHOR]

In this paper, a 1 kW-class Solar-Ocean Thermal Energy Conversion integrated Air-Conditioning (S-OTEC/AC) experimental system, which can provide both electrical energy and cooling energy without any pollution, is constructed for the first time. Based on the experimental data, the system's overall performance was comprehensively evaluated in terms of energy, exergy, economy, and environment (4 E). Furthermore, the performance difference between the system using solar energy (i.e., S-OTEC/AC) and the system without solar energy (i.e., OTEC/AC) was compared. The experimental results revealed that the maximum thermal efficiency of the S-OTEC/AC system could reach 2.10%, which was 1.91 times higher than the OTEC/AC system. For the OTEC/AC and S-OTEC/AC systems, the maximum cold energy utilization efficiency was 4.12% and 10.09%, and the maximum isentropic efficiency was 18.81% and 76.84%, respectively. The minimum payback period for the S-OTEC/AC system was 13.90 years, which was much lower than the 18.40 years of the OTEC/AC system. Additionally, the maximum primary energy saving achieved by the OTEC/AC system was 0.53 kW, while the S-OTEC/AC system reached a higher value of 1.56 kW. From the results, the superiority of the S-OTEC/AC system over the OTEC/AC system was confirmed. This work not only provides data references for the actual operating characteristics of the S-OTEC integrated system, but also provides a new technical way for comprehensive utilization of ocean temperature difference energy. • 1 kW class S-OTEC/AC experimental system was built for the first time. • The first 4 E analysis was used to characterize S-OTEC/AC with experimental data. • The S-OTEC/AC system has a thermal efficiency of up to 2.10%. • The S-OTEC/AC system achieves a cooling energy utilization of 10.09%. • The S-OTEC/AC system is superior to the OTEC/AC system in all aspects. [ABSTRACT FROM AUTHOR]

As we all know, how to achieve better energy savings has been mentioned on various countries’ energy schedules. Public buildings as a large energy consumption. It’s air conditioning system has a lot of energy-saving space, and air-conditioning chilled water system to optimize energy-saving control is an important measure to achieve energy-saving air-conditioning system initiatives. This paper mainly focuses on the control system of variable frequency pump in chilled water system. For the water pump control strategy, the secondary pump frequency control strategy is discussed, in order to obtain a better control strategy, in detail the current commonly used differential pressure control strategy. In this paper, five kinds of differential pressure control strategies are analyzed, and then the simulation model is simulated by the established mathematical model. The input energy consumption model of the inverter - motor - water pump micro - system is obtained and the simulation results are analyzed. [ABSTRACT FROM AUTHOR]

This paper presents new metrics to measure the effect of thermal mass on the energy required to heat and cool buildings. Previous studies have been flawed as they have not considered the interaction between intermittent occupancy and thermal mass, which has a significant impact on overall energy use. However, existing parameters do not adequately capture these effects, so the new metrics developed in this paper are used to analyse the impact of thermal mass in hot climates with active cooling, and cold climates with active heating. The results agree with existing literature that high thermal mass structures are likely to be effective in hot climates; however, in cold climates the drawbacks of high thermal mass likely outweigh the advantages, and high thermal mass can cause an increase in energy use. This finding has implications for the design of buildings in cold climates, and contradicts the commonly-held assumption that high thermal mass is correlated with low energy use. The new metrics (transient energy ratio and effective U -value) provide a generalisable method to quantify these effects. They are further used here to analyse the dynamic performance of heavily insulated buildings and show that high thermal mass often leads to higher energy use in cold climates. [ABSTRACT FROM AUTHOR]

There has been an increasing concern on thermal comfort in sleeping environments and its associated energy use in the past few years. To improve the thermal environment and to reduce energy use of air conditioning in bedrooms, applications of task/ambient air conditioning (TAC) systems were proposed and studied previously. It’s indicated that the TAC system can be well integrated with a bed. Due to the variation of the envelope heat gain in a bedroom during night, it is necessary to study the thermal environment inside a bedroom and the energy use of a TAC system for the bedroom at varying envelope thermal loads. Therefore, this paper reports on a numerical study on a TAC system applied to a bedroom with different envelope heat gains. The influences of envelope heat gain on energy consumption of the TAC system and the indoor thermal comfort were studied in this paper. The research results show that at supply air flow rate ( Q s ) of 50 l/s, energy consumption was increased from 47.78 W to 213.11 W, and the PMV value was increased from −1.69 to −1.29 with the increase in envelope heat gain from 3.11 W to 155.6 W. To make PMV equal to zero under different envelope heat gains, linear regression models between supply air parameters and PMV were built and solved. The obtained values form curves where PMV = 0 and give a guide for operation of the TAC system. It was found that the calculation of energy consumption on these curves depends only on envelope heat gain. [ABSTRACT FROM AUTHOR]

This paper presents an energy-saving controller for automotive air-conditioning/refrigeration (A/C-R) systems. With their extensive application in homes, industry, and vehicles, A/C-R systems are consuming considerable amounts of energy. The proposed controller consists of two different time-scale layers. The outer or the slow time-scale layer called a set-point optimizer is used to find the set points related to energy efficiency by using the steady state model; whereas, the inner or the fast time-scale layer is used to track the obtained set points. In the inner loop, thanks to its robustness, a sliding mode controller (SMC) is utilized to track the set point of the cargo temperature. The currently used on/off controller is presented and employed as a basis for comparison to the proposed controller. More importantly, the real experimental results under several disturbed scenarios are analysed to demonstrate how the proposed controller can improve performance while reducing the energy consumption by 9% comparing with the on/off controller. The controller is suitable for any type of A/C-R system even though it is applied to an automotive A/C-R system in this paper. [ABSTRACT FROM AUTHOR]

Traditional air conditioning may be inappropriate for electric vehicles due to its moving parts noise besides using chlorofluorocarbons that harm the environment. In addition, it consumes a significant portion of the stored energy in batteries, reducing the vehicle's driving range. So, in this paper, a novel design of thermo-electric cooling (TEC) system coupled with a photovoltaic (PV) panel replacing the vehicle roof is studied. This system consists of a sandwich of PV panel outside the vehicle and TEC inside with a heat sink system integrated between them. The air temperature variation in the cabin during the daytime is predicted by solving a complete mathematical transient thermal model of the whole system before and after mounting the cooling system. The air streams through the vehicle moving are exploited to improve the TEC and PV system performance. The system performance is investigated for different cases during the day with and without including the PV output power and for the vehicle parks inside or outside. The results indicate that, for each scenario, the number of used TEC modules influences the system performance where the best number varies between 128 and 98. Coupling the PV panel with the TEC system reduces the daily required energy from batteries by about 19%. Running the TEC system during parking from 8 to 10 am decreases the cabin air temperature from 47.5 to 34°C while the input power declines by about 45%, which reduces the interior temperature to 25°C in 10 min (transition time). The contribution of the PV panel based on the studied conditions can increase the range of the vehicle by 10.4 km/day and about 160kWh/year energy saving. The reduction in the input power during transition time reaches 27.8% when the vehicle speed increases from 30 to 60 km/h, while this ratio declines to 10.8% as the vehicle speed rises from 60 to 90 km/h. During vehicle moving, powering the TEC system by the PV panel only can prevent the cabin temperature from rising over 40°C, whereas during parking, there is an optimum fan air velocity that gives the maximum reduction of the cabin temperature. • A novel design of a thermo-electric air conditioning system for electric vehicles is studied. • Contribution of the PV panel reaches 19% of the daily energy consumption in some scenarios. • PV panel increases the range of the vehicle by 10.4 km and can save 160kWh/year. • The best number of TEC modules is about 128 for scenarios 1 and 2 and 98 for the others • Power the TEC by PV power in parking reduces the vehicle temperature less than ambient. [ABSTRACT FROM AUTHOR]

[Display omitted] • A novel approach to control CO 2 and H 2 O composition in an enclosed environment. • A cyclic CO 2 adsorption process and dehumidication units are considered. • The mathematical model shows superior performance of the proposed system. • Carbon footprint of the system is discussed with scale-up study. • Influence of parametric uncertainties in the model is discussed. Rapid growth in global energy consumption has raised concern on the environmental impacts such as ozone layer depletion and climate change. Enclosed space, such as commercial buildings, accounts for about 40% of global energy consumption and the demand is constantly increasing due to increasing population, urbanization, and economic development. The energy demands in the building sector calls for strategic measures to develop energy efficient technologies. This paper presents a strategy to decrease energy demands inside buildings by proposing a ventilation system which regulates the enclosed air quality resulting in reduced air conditioning. The system consists of multiple adsorption beds with zeolite 13X monoliths for CO 2 removal, and silica gel for humidity control, inside the enclosed space. The air conditioning system results in decrease in energy requirement and improvement in economics by 55% as compared with conventional ventilation system. The model is scaled up to the size comparable with total office inventory of New York City, and the reduction in carbon emissions by introducing the air composition control system for New York City is equivalent to replacing 57 million incandescent light bulbs by LEDs. This paper concludes that the air conditioning system proposed in this study results in the improvement in performance as compared to a conventional ventilation system and could reduce energy consumption inside commercial buildings. [ABSTRACT FROM AUTHOR]

Saudi Arabia is characterized with high temperature, humidity, and dust storms. The air conditioning systems are an essential component in daily life. 60% of the energy consumed in the residential area is used by air conditioning systems. The aim of this paper is to build a residential thermal HVAC model, which could predict the amount of energy consumption required to get the comfort level using Matlab/Simulink. In this model the different physical properties of the building, weather, and heating gains are taken to account. The results of energy consumption obtained from Matlab/Simulink model are based on using the actual hourly outdoor temperature for a selected day of 2012 compared to the average outdoor temperature of the same selected day. The results of energy consumption for the actual and average temperatures are almost identical. For this reason, the results of total energy consumption are presented in this paper for every day of the annual year of 2012 based on the average hot and warm outdoor temperatures (7 1/2 months), and cool and cold temperatures (4 1/2 moths). [ABSTRACT FROM AUTHOR]

This paper summarises the results of a study to identify and quantify the potential impact of measures and policies to reduce the energy consumption of air conditioning in European countries over a 10-year period. The market penetration of air conditioning in Europe has increased steadily over several decades. On a “business as usual” basis, its energy consumption would increase by over 50% by 2020. Measures to restrict this increase are therefore important, but the savings potential straddles several overlapping areas which are subject to different constraints including those imposed by the replacement rates of systems and products, and the refurbishment rates of existing buildings. This work reported in this paper is based on the use of information from a variety of sources in a highly disaggregated model to assess the “realisable” savings over a 10-year period, taking into account relevant constraints. The paper summarises results at a European level, focussing on those cases that generate the greatest realisable savings. Savings are possible in three areas: improved equipment and system efficiency, reduced cooling loads, and more effective operation. The cases that offer the largest savings provide the basis for recommendations for policy measures, often using existing policy instruments. In addition, areas where further work is needed are identified. More detailed results and information about the study and additional recommendations can be found at http://www.bre.co.uk/searchresults.jsp?category=5&q=energy+management [1] . [ABSTRACT FROM AUTHOR]

• Propose a novel machine learning-based model predictive control (MLB-MPC) framework with predictive inputs of cooling load and outdoor wet-bulb temperature. • Obtain the optimal match of prediction models and optimization algorithms for improving the performance of the MLB-MPC. • Investigate the impact of disturbances on the performance of global optimization. • Achieve an energy-saving ratio of 7.1% for the air-conditioning system when compared with the measured operation data. The dynamic optimization of key setpoints (e.g., supply water temperatures of chillers and cooling towers, or indoor temperature and humidity) can track the efficient performance point of the air-conditioning system (ACS), thus obtaining a great energy-saving effect. The model predictive control is an effective way to precisely adjust these setpoints. However, most of the existing studies focused on simple linear strategies, e.g., experience-based, rule-based, or component-based, which results in unsatisfactory energy efficiency. Aiming at this, the paper proposed a novel machine learning-based model predictive control (MLB-MPC) framework with predictive inputs of disturbances. The framework first employed the grid search and cross-validation to optimize the total energy consumption prediction models (TECPMs), which were built by data-driven models (e.g., multiple linear regression, artificial neural network, support vector regression (SVR), and random forest). And then the optimization performances of each TECPM to the controlled variables were obtained by using different optimization algorithms (e.g., genetic algorithm, particle swarm optimization (PSO), and simulated annealing). Finally, the optimal match of TECPMs and optimization algorithms was achieved by trade-off among prediction accuracies, optimization accuracies, and optimization time. The case studies demonstrated that the optimal match for the MLB-MPC is SVR and PSO as they had the highest prediction accuracy (mean absolute percentage error of 2.5%) and shortest optimization time (41 ms/per) and optimization accuracies with little difference. After adopting the optimal match, the MLB-MPC with predictive disturbing inputs achieved a great energy-saving ratio of 7.1% for the ACS, which was only less than the MLB-MPC with ideal disturbing inputs by 0.4%. This indicated that exact predictions of disturbances (e.g., cooling load and outdoor wet-bulb temperature) are important for the MLB-MPC. The proposed MLB-MPC framework would provide a method for improving the energy efficiency of ACSs. [ABSTRACT FROM AUTHOR]

• An improved system is proposed based on multi-fans with frequency conversion. • The improved system meets pressure control requirement in non-working modes. • The energy saving and cleanliness can be achieved by switching operation modes. Pressure control for cleanrooms in the pharmaceutical industry is a necessary means to avoid the cross-contamination. The pressure control of traditional air conditioning can only handle the working stage. In the non-working stage, the system cannot reduce the air change rate per hour (ACH) in order to alleviate the problem of high energy consumption. This paper proposes an improved air conditioning system, which focuses on the ability to control pressure gradient of the system in working and non-working mode. By theoretical derivation of the combined fan frequency conversion, when the impedance and volume of the infiltration air satisfy S i G Z , i = S j G Z , j = S k G Z , k = c o n s t a n t , the pressure gradient in multi-zone cleanrooms can remain stable. A mathematical model of the system has been established, which includes five modules: air pipe network, fan characteristic curve, fan operating point solution, variable volume damper characteristic curve and multi-zone network pressure gradient solution. The correctness of the model is verified by field measurements. Taking a clean workshop as case study, the room pressure can be stabilized in the range of ± 3 Pa by switching the working and non-working mode, which can save 39.8% of the energy consumption in non-working mode, while ensuring cleanliness. This paper demonstrates the process of the air pipe network's influence on cleanrooms pressure and proves the effectiveness of improved purification air conditioning system in pressure gradient control and energy saving potential. [ABSTRACT FROM AUTHOR]

Abstract: Air conditioning is essential for maintaining thermal comfort in indoor environments, particularly for hot and humid climates. Today, air conditioning, comprising cooling and dehumidification, has become a necessity in commercial and residential buildings and industrial processes. It accounts for a major share of the energy consumption of a building or facility. In tropical climates, the energy consumed by heating, ventilation and air-conditioning (HVAC) can exceed 50% of the total energy consumption of a building. This significant figure is primarily due to the heavy duty placed on cooling technologies to remove both sensible and latent heat loads. Therefore, there is tremendous potential to improve the overall efficiency of the air-conditioning systems in buildings. Based on today’s practical technology for cooling, the major components of a chiller plant are (1) compressors, (2) cooling towers, (3) pumps (chilled and cooling water) and (4) fans in air handling units. They all consume mainly electricity to operate. When specifying the kW/Rton of a plant, there are two levels of monitoring cooling efficiency: (1) at the efficiency of the chiller machines or the compressors which consume a major amount of electricity; and (2) at the overall efficiency of cooling plants which include the cooling towers, pumps for moving coolant (chilled and cooling water) to all air-handling units. Pragmatically, a holistic approach is necessary towards achieving a low energy input per cooling achieved such as 0.6kW/Rton cooling or lower by considering all aspects of the cooling plant. In this paper, we present a review of recent innovative cooling technology and strategies that could potentially lower the kW/Rton of cooling systems – from the existing mean of 0.9kW/Rton towards 0.6kW/Rton or lower. The paper, broadly divided into three key sections (see Fig. 2), begins with a review of the recent novel devices that enhances the energy efficiency of cooling systems at the component level. This is followed by a review of innovative cooling systems designs that reduces energy use for air conditioning. Lastly, the paper presents recent developments in intelligent air-control strategies and smart chiller sequencing methodologies that reduce the primary energy utilization for cooling. The energy efficient cooling technology, innovative systems designs, and intelligent control strategies described in the paper have been recently researched or are on-going studies. Several have been implemented on a larger scale and, therefore, are examples of practical solutions that can be readily applied to suit specific needs. [Copyright &y& Elsevier]

Abstract: Reducing the energy consumption of air-conditioning systems is becoming increasingly important. This paper focuses on the air-conditioning system in Terminal 3 in Xi’an Xianyang International Airport, the first airport terminal to adopt radiant cooling in China. In the large spaces of this airport terminal, a temperature and humidity independent control (THIC) system has been adopted instead of a conventional nozzle air supply method, which significantly reduces the energy consumption of the air supply. The radiant floor is the main mechanism for indoor temperature control, while a liquid desiccant outdoor air processor combined with displacement ventilation is responsible for humidity control. Ice storage is adopted to reduce operating costs, and the supplied chilled water temperature can be as low as 3°C. This paper examines the performance of the THIC system in detail. The indoor environment is determined through measurements to be comfortable, and the on-site performances of key components in both the airport terminal and the cooling plant are investigated. The outdoor air processor supplies air of appropriate temperature and humidity ratio; two kinds of radiant floors are used for temperature control, both with measured cooling capacities of about 30–40W/m2; and the energy efficiency ratio (EER) of the cooling plant is 2.62. [Copyright &y& Elsevier]

Abstract: This paper models the past and future sales, replacement rates and installed stock levels of air conditioning products in Europe. Established market diffusion models have been reformulated to allow their calibration against product sales data, and then used to estimate future and past sales levels, time-dependent product replacement rates and installed stock levels in each EU-27 country for each of the major energy-using air conditioning products. The results show that, for most air conditioning products, continuing growth of sales and stock is to be expected, albeit at lower rates than in previous years. Expressed in terms of kW cooling power, split-system room air conditioners and chillers continue to account for the majority of sales and stock, with variable refrigerant flow (VRF) systems taking an increasing share of first-time installations. The results provide fundamental information on which to base policy assessments (which are not part of this paper). [Copyright &y& Elsevier]

Abstract: This paper sets the viewpoint of air-conditioning system from heat sources and humidity sources, especially focusing on the temperature distribution of heat sources and how it influences the efficiency of air-conditioning system. For humidity sources, they are different from heat sources for their physical essence, which provides the possibility of separate treatment of heat and humidity. This paper establishes the ideal air-conditioning system of cooling and dehumidifying, based on the ideal treatment of heat sources, and humidity sources. Then the difference between ideal system and actual system are explored by a case study showing the decrease of efficiency step by step. The gap between ideal system and actual system can be concluded into three main imperfections: the method of treatment of heat sources, transmission temperature difference and heat exchange temperature difference, and the energy consumption of transportation. In the last, according to the actual influencing factors, some improving directions are proposed to improve the current system correspondingly. [Copyright &y& Elsevier]

The American Society for Heating, Refrigeration, and Air Conditioning Engineers (ASHARE) prescribes fixed ventilation rates for the operation of heating, ventilation, and air conditioning (HVAC) systems, which is sub-optimal in terms of controlling indoor air pollutants and energy consumption. This paper relies on a physics-based model of a residential house to predict the concentrations of indoor pollutants such as ozone, formaldehyde (HCHO), and particulate matter (PM) as function of time, outdoor conditions, and indoor emissions. The model captures real-world scenarios such as pollutants entering the house from ambient air through an air handling unit (AHU) and pollutants emitted in the house. A dynamic optimization problem is then formulated and solved to calculate the optimal ventilation rate at each time instant, that minimizes the total energy consumption, while maintaining the indoor pollutant concentrations below or as close as possible to their respective acceptable thresholds. For the considered example day, operation under optimized conditions reduces the peak pollutant concentration by 31%, time of exposure to undesirable concentrations by 48%, and energy consumption of the AHU by 17.7%. [ABSTRACT FROM AUTHOR]

Abstract: Pump is main equipment in air conditioning systems and used widely, but its energy consumption is great. In order to improve energy efficiency, using pump controlled by frequency-conversion technology is an effective method. In this paper, the working principle and control method of variable frequency pump is described in detail, and gives a comparison between variable frequency control and traditional control about energy saving effect. Because traditional PID controller can be hard to get good control performance in pump control, this paper presents a control method using fuzzy logic controller to achieve frequency conversion and constant pressure water supply. The controlled variable is obtained by fuzzy control table. The system has energy-saving, security, and stable water pressure, etc. Simulation results show that the proposed controller not only have good robustness, but also have good dynamic and static performance. [Copyright &y& Elsevier]

Abstract: Evaluating a building’s performance usually requires a high number of sensors especially if individual rooms are analyzed. This paper introduces a simple and scalable model-based virtual sensor that allows analysis of a buildings’ heat consumption down to room level using mainly simple temperature sensors. The approach is demonstrated with different sensor models for a case study of a building that contains a hybrid HVAC system and uses fossil and renewable energy-sources. The results show that, even with simple sensor models, reasonable estimations of rooms’ heat consumption are possible and that rooms with high heat consumption are identified. Further, the paper illustrates how virtual sensors for thermal comfort can support the decision making to identify the best ways to optimize building system efficiency while reducing the building monitoring cost. [Copyright &y& Elsevier]

Abstract: The use of hygroscopic materials for moisture buffering is a passive way to moderate the variation of indoor humidity. Through absorption and desorption, surface materials in the indoor environment, such as curtains, carpets and wall paper, are able to dampen the moisture variations. The moisture buffering capacity of these materials may be used to improve the relative humidity of the indoor environment at reduced energy costs. The objectives of this paper are threefold. The first objective is to derive a theoretical model for the transient moisture transfer between a curtain system and the indoor air for the case where the curtain is placed in front of a wall. The second objective is to conduct experiments inside environmental chambers to validate the theoretical model and to test the ability of curtains to moderate indoor humidity. It is shown that the experimental results for the curtain moisture uptake and the relative humidity inside the chamber compared well with the model simulation results. The third and final objective is to test and evaluate the model under “real environment conditions” for a case study of a hygroscopic cotton curtain, placed in a “typical” office space in the city of Beirut with an area of 25m2 that uses direct expansion (DX) air conditioning system. It is found that hygroscopic curtains maintain humidity of less than 65% during part load operation compared to the upper limit of 70% relative humidity when no curtain is used. On the other hand, it is found that the energy use, as determined by the daily electrical power consumption of the DX system, is almost the same for the two cases, (with and without a curtain), where approximately 20kWh of energy input is required 13kWh of sensible energy and 7kWh of latent energy. [Copyright &y& Elsevier]

Abstract: Heat is transferred through building envelopes by conduction, radiation, and convection. Of these, convective heat transfer is often the weakest ‘link’ in the overall heat transfer model. While conduction and radiation heat transfer are supported by well-established analytical and numerical models, the treatment of convection is much less rigorous. Convection modeling involves solution of fluid dynamics problems in which the complexity of an enclosed space''s geometry and the diversity of indoor airflow patterns require many fit-for-purpose convection correlations. These must take into account specifics of the space and of the heating ventilation and air-conditioning (HVAC) system. This paper provides an overview of the current knowledge on the modeling of convective heat transfer in load calculation and building energy simulation programs. The paper also discusses various issues related to the robustness of convection coefficient correlations, and reports on new experiments conducted to test the sensitivity of existing convection correlations. The discussed issues relate to: (1) the non-uniformity of the indoor temperature field; (2) the selection of a proper characteristic dimension; (3) the effect of adiabatic and non-adiabatic obstructions in the zone; and (4) the impact of airflow disturbance. [Copyright &y& Elsevier]

Abstract: The performance of different HVAC systems varies when coupled with different buildings. This paper examines the relationship between building heating and cooling load and subsequent energy consumption with different HVAC systems. Two common HVAC systems in use throughout the UK office building stock, variable air volume (VAV) system and fan coil (FC) with dedicated outside air system, have been coupled with a typical narrow plan office building with and without daylight control and for both cellular and open plan. The results presented in this paper clearly indicate that it is not possible to form a reliable judgment about building energy performance based only on building heating and cooling loads. For the two investigated systems, variable air volume system and fan coil with dedicated outside air system, the difference between system demand and building demand varied from over −40% to almost +30% for cooling and between −20% and +15% for heating. If a heat recovery unit is used, the difference in heating performance is even greater, rising to −70%. [Copyright &y& Elsevier]

Abstract: In arid climates, evaporative cooling technologies are generally valued for their reduced energy consumption in comparison to compressor-based air conditioning systems. However, two concerns that are often raised with respect to evaporative cooling equipment are their on-site water use and the impact of poor water quality on their performance. While compressor-based systems do not use water on-site, they do consume water through their use of electricity, which consumes water through evaporation at hydroelectric power plants and cooling at thermal power plants. This paper defines a water-use efficiency metric and a methodology for assessing the water use of various cooling technologies. The water-use efficiencies of several example cooling technologies are compared, including direct evaporative, indirect evaporative in two different configurations, compressor-based systems, compressor-based systems with evaporative pre-cooling of condenser inlet air, and hybrid systems that consist of an indirect evaporative module combined with a compressor-based module. Designing cooling systems for arid climates is entwined in the close relationship between water and energy and the scarcity of both resources. The analyses presented in this paper suggest that evaporative systems that significantly reduce peak electricity demand and annual energy consumption need not consume any more water than conventional systems. [ABSTRACT FROM AUTHOR]

Abstract: Incorporating energy efficiency and sustainable green design features into new/existing buildings has become a top priority in recent years for building owners, designers, contractors, and facility managers. This paper intends to address why delivery of an energy efficient building is not just the result of applying one or more isolated technologies. Rather, it can best be obtained using an integrated whole building process throughout the entire project development process, which leads building designers to generate a large amount of data during energy simulations. The authors observed that even a simple energy modeling run generated pages of data with many different variables. The volumes of energy modeling data clearly overwhelm traditional data analysis methods such as spreadsheets and ad-hoc queries with so many factors to be considered. An integrated or whole building design process involves studies of the energy-related impacts and interactions of all building components, including the building location, envelope (walls, windows, doors, and roof), heating, ventilation and air conditioning (HVAC) system, lighting, controls, and equipment, which shows why it is so difficult to find the correlation between different systems. The objective of this research is to develop an energy efficient building design process using data mining technology which can help project teams discover important patterns to improve the building design. This paper utilizes the data mining technology to extract interrelationships and patterns of interest from a large dataset. Case study revealed that data mining based energy modeling help project teams discover useful patterns to improve the energy efficiency of building design during the design phase. The method developed during this research could be used to guide designers and engineers through the process of completing an early design energy analysis based on energy simulation models. [ABSTRACT FROM AUTHOR]

Abstract: As dehumidification is one of the most important tasks of environment control of the building, it is necessary to know the energy efficiency of dehumidification processes. The energy efficiency can give the energy cost of drawing moisture from indoor air to the outside environment. This paper presents analysis of the ideal cost of dehumidification process by a liquid desiccant cycle. Formulas to calculate ideal efficiency of dehumidification process are obtained, which is determined by indoor temperature, outdoor temperature, and the temperature of the intersection point of the iso-relative humidity line of indoor air and the iso-humidity ratio line of outdoor air. The ideal efficiency of the condensing dehumidification method is lower than the ideal dehumidification process, due to the fact that condensing dehumidification method must dehumidify the air at the temperature of dew point. Results from this paper can be used as theoretical foundation for the further analysis of various dehumidification methods and the development of new dehumidification processes. [ABSTRACT FROM AUTHOR]

Abstract: This paper aims to study the various parameters that affect the energy performance of commercial buildings in Singapore. The parameters are diverse, ranging from characteristics of construction of the walls and windows, to the various system settings and types within the building. Building energy performance is measured via two key indexes, namely, the Envelope Thermal Transfer Value (ETTV) and the annual cooling energy requirement (E c). Parameters related to these two indexes are identified. An additional parameter, the solar absorptance of the wall, is further incorporated to calibrate the ETTV equation. A relative ranking on the functional parameters of ETTV has been performed to evaluate their effectiveness in lowering the ETTV of buildings. In addition, the impact of using cladding on ETTV is also studied. A correlation for E c, expressed in the form of a simple linear equation, has been developed. This correlation accounts for the internal building loads, envelope loads, operating schedules and efficiency of the cooling equipment. Finally, ETTV and E c have been employed to study the effects of chiller over-sizing and ventilation rates on building cooling energy. In the pursuit for better energy-efficient buildings, the approach presented in this paper contributes to the construct of sustainable energy-efficient built-environment. [Copyright &y& Elsevier]

Abstract: Thermally activated building systems (TABS) integrate the building structure as energy storage, and have proofed to be energy efficient and economic viable for the heating and cooling of buildings. Although TABS are increasingly used, in many cases control has remained an issue to be improved. In this paper, a method is outlined allowing for automated control of TABS in intermittent operation with pulse width modulation (PWM). This method represents one part of a TABS control solution with automatic switching between cooling and heating modes for variable comfort criteria which was published before. A first pulse width modulation control solution is derived based on a simple 1st order model of TABS. Then a second, even simpler solution is given that significantly reduces the tuning effort. Finally, the paper outlines a pulse width modulation control procedure and gives two application examples of the PWM control carried out in a laboratory test room. [Copyright &y& Elsevier]

This paper presents an autonomous hierarchical control method for a direct expansion air conditioning system. The control objective is to maintain both thermal comfort and indoor air quality at required levels while reducing energy consumption and cost. This control method consists of two layers. The upper layer is an open loop controller that allows obtaining tradeoff steady states by optimizing the energy cost of the direct expansion air conditioning system and the value of predicted mean vote under the time-of-use price structure of electricity. On the other hand, the lower layer designs a model predictive controller, which is in charge of tracking the tradeoff steady states calculated by the upper layer. Control performance of the proposed control method is compared to a conventional control strategy. The results show that the proposed control strategy reduces the energy consumption and energy cost of the direct expansion air conditioning system by 31.38% and 33.85%, respectively, while maintaining both the thermal comfort and indoor air quality within acceptable ranges, which validate the proposed methodology in terms of both comfort and energy efficiency. [ABSTRACT FROM AUTHOR]

Configuring the number and size of chillers in a multiple-chiller plant properly is an efficient way to improve the plant energy efficiency. At the design stage, the optimal configuration can be achieved through matching the capacity to load as closely as possible across the full-load profile. However, in spite of the fact that current literature offers practical recommendations, a systematic method to optimize the configuration of multiple-chiller plants is lacking. Due to the lack of accurate information at the design stage and only limited knowledge of the eventual realization it is hard to predict the building’s cooling load. Moreover, there is no operational data to predict the system performance. Both explain the existence of uncertainty in the HVAC plant design process. This paper, therefore, proposes a strategy to optimize the configuration of multiple-chiller plants, which takes account of the load side uncertainty as well as the COP uncertainty and selects the optimal configuration through a life-cycle analysis. Both the load side uncertainty and the COP uncertainty are quantified using statistical distributions. To facilitate applications, the distributions of the cooling load profile of different types of buildings under different weather conditions are investigated and are classified into four categories, and the optimal configuration schemes under each type of cooling load distribution are analyzed and summarized in a tabulated form. [ABSTRACT FROM AUTHOR]

The increased demand of energy in domestic applications necessitates the development of innovative engineering solutions in building heating, ventilating, and air conditioning (HVAC) systems. As the largest energy intensive sector is domestic buildings, more focus is currently directed to reduce air conditioning energy consumption. Double-pipe heat exchangers are considered one of the practical solutions in today’s HVAC industry. Nevertheless, a few studies focus on using double-pipe heat exchangers in air conditioning applications. This paper experimentally investigates the usage of double-pipe condenser and evaporator in an air conditioning system serving a 45 m 3 balanced calorimeter of 2.24 kW heat load. Deionized water (DIW) was used as the secondary heat transfer working fluid for both the evaporator and condenser units, and R-22 was used as the AC system refrigerant. Experimental results of the double-pipe heat evaporator/condenser setup showed a promising reduction in the compressor work and an increase in the system coefficient of performance (COP). The collected data showed that the system efficiency depends more on the evaporator DIW flowrate than on the condenser DIW flowrate. By increasing the DIW flowrate in the evaporator, the compressor work was shown to decrease, while the COP was shown to increase. In comparison with a standard rated air conditioning unit, using a double-pipe evaporator and condenser units with the maximum DIW flowrates resulted in a decrease of about 53% in the compressor work and a similar percentage of increase in the system COP. [ABSTRACT FROM AUTHOR]

The purpose of air-conditioning systems is to provide a suitable indoor environment with respect to temperature, humidity and fresh air. Liquid desiccant dehumidification constitutes an effective method for extracting moisture from humid air with less energy consumption. Current studies mainly focus on dehumidification system under certain heat and mass transfer ability (number of mass transfer units NTU m ). This paper will investigate NTU m of counter-flow packing tower and its influence on system performance. An experiment including a counter-flow packing tower was conducted. When the height of tower was 0.7 m, the volumetric mass transfer coefficient was between 1–4 kg/(m 3 ·s) and NTU m presented a range between 0.9–1.4, when air flow rate changes from 1 kg/(m 2 s) to 2.5 kg/(m 2 s). When the height changed to 2.1 m, the NTU m of the tower presented a variation from 3.3 to 4.3. Furthermore, a simulation model is developed, which is validated by experimental data and past research results. The influence of NTU m on total circulation flow path is mainly caused by heat and cold offset and an NTU m value approximately of 4 constitutes a suitable value of increasing heat and mass transfer ability. Comparing three typical flow paths, when NTU m is lower than 3.5, inter-stage circulation presents improved performance in system COP. When NTU m is large, total circulation is efficient. The system COP cross points of flow paths are caused by heat and cold offset and concentration difference of the solution circulation between the dehumidifier and the regenerator, which can be quantified by loss coefficient ε and χ respectively. The heat and mass transfer ability of the system should be considered in the designing process of flow path configuration to obtain an efficient performance for different range of NTU m . [ABSTRACT FROM AUTHOR]

With the increased complexity of air conditioning systems, the computational load and complexity of real-time optimization appear to be challenging for applications. To overcome the challenge, multiplexed optimization has been proposed in which multiple set-points are sequentially optimized and updated one by one. In such a way, it can achieve equivalently-good energy performance but with exponentially reduced computational load if compared with those traditional methods that optimize all set-points simultaneously. In fact, the time instant for each set-point optimization and the set-point optimization sequence have impacts on the overall performance of the multiplexed optimization. Considering such impacts, this paper proposes a new multiplexed optimization method for enhanced performance. In the proposed method, optimization is activated as the system energy efficiency is low. The set-point optimization sequence is selected according to their impacts on the system energy performance. The one with the most energy saving potential will be firstly optimized. The case study results demonstrate the improved performance of the proposed method in terms of energy, computation load and system stability when compared with the conventional multiplexed optimization. The proposed method can be applied in complex air conditioning systems for energy saving, computation load reduction and system stability improvement. [ABSTRACT FROM AUTHOR]

The main purpose of this research is to suggest a virtual water flowmeter applicable in hydraulic systems with low-cost sensors. Practical procedures for realizing virtual water flowmeters for constant flow pumps (i.e., Cases 1 and 2) and variable flow pumps (i.e., Cases 3 and 4) are proposed in this paper. In Case 1, for measuring the water flow rate through a constant flow pump, the pump head was measured and the water flow rate was estimated using the pump characteristic curve obtained from the manufacturer or by deriving an empirical model based on the field measurement data. In Case 2, the water flow rate through a valve with a constant flow pump was estimated by measuring the pressure head between the valve and the valve opening position. The valve characteristic curve can be obtained by deriving an empirical model based on the initial field test results. The water flow rate through the variable flow pump was calculated, using the pump affinity laws and an empirical model, by measuring the frequency (i.e., Case 3) or input power (i.e., Case 4). The initial setup and test procedures for virtual flowmeters are also proposed in this research for practical use in the field. To verify the proposed procedures, experiments were conducted using constant and variable flow pumps in a pilot system. It was found that the virtual water flowmeters showed 2.9% to 6.7% of root mean square error from Case 1 to Case 4, compared with an ultrasonic water flowmeter, through long-term experimental verification. [ABSTRACT FROM AUTHOR]

With the rapid development of Internet communication business, the issues related to the space, efficiency and energy consumption of data center are increasingly attracting more attentions. Because the modular air conditioning system has the advantages of quick construction, easy replication, rapid deployment, flexible scalability, high cooling efficiently, it has become a way to solve the bottleneck problem of traditional data center. In this paper, a data center being equipped with modular air conditioning system in Tianjin is taken as an example to analyze the energy and electricity saving and the characteristics of deployment by steps. The practice of this example shows the feasibility and prospects of applying modular air conditioning system in data center. [ABSTRACT FROM AUTHOR]

The data centre air conditioning system has a huge energy consumption and has the characteristic of requiring year-round cooling. Cooling tower cooling technology can realize free cooling and reduce the operating time and energy consumption of the refrigeration host. In this paper, through the engineering examples, it discusses the cooling tower with free cooling of the air conditioning system combined with conventional refrigeration way design points. It analyses the way to realize the operation and transformation of conventional refrigeration mode, free cooling mode, partial free cooling mode and other operation modes through automatic control system. [ABSTRACT FROM AUTHOR]

With the global energy crisis, energy-saving issues have been great attention to HVAC industry. As for the building atrium with large space, the indoor air diffusion has been hot-pot. Air conditioning system which can meet the requirement of indoor human thermal comfort and reduce the energy consumption of buildings has become the focus of scholars. The GAMBIT software is used to build the corresponding geometric model and divide it into meshes in this paper. The FLUENT software is used to simulate the airflow organization of the atrium winter air-conditioning system. In the simulation calculation, the physical model uses the turbulence model, the two-equation k-ε model and standard SIMPLE algorithm are used to simulate the equation, the boundary condition is set to the second boundary condition. The influence of factors that different air supply angles, velocity, temperature, the outlet height on temperature field and velocity field in atrium were simulated by FLUENT, and the thermal comfort of work area was analyzed. According to the three factors of heat comfort, ventilation efficiency and energy utilization coefficient, the weight coefficient method was used to evaluate the airflow organization in different conditions, and the optimal air supply parameters were determined. [ABSTRACT FROM AUTHOR]

Airflow pattern in a data center impacts the cooling effectiveness of the air-conditioning systems significantly, and hence impacts the energy efficiency of the whole data center. This paper presented investigation of 3 airflow patterns for a typical data center by CFD simulation. An under-floor air supplying system, row-level cooling system and rack level cooling system was used in the targeted data center. Cooling performance was simulated by CFD software. The cooling performance was compared by indices like Index of Mixing (IOM), Return Temperature Index (RTI), Temperature Inequality Index K T , Mean Temperature Difference Index of Rack Intake and Exhaust Air, Energy Utilization Coefficient. The results indicated that rack level airflow pattern shows the best performance in data center cooling. Compared with under-floor air supplying system, the IOM index is only 0.0011, and the K T index is 0.0082. In the end an optimization method was proposed for the deficiencies in rack level cooling system. [ABSTRACT FROM AUTHOR]

The outdoor low temperature fresh air can be used as a free cold source to eliminate waste heat for the building interior zones during the transition season and winter. This paper takes a project in Hunan as an example, and the project building interior zones is 25m×7m×3.9m(L×W×H). Using Fluent software to simulate the temperature field and velocity field both the interior and exterior zones of the engineering offices. The simulation results show that using the displacement ventilation system to take the outdoor air into inner rooms not only cooling but also improving the air quality and adding comfort. According to the simulation results and outdoor air dry bulb temperature and enthalpy values, the h - d diagram is divided into three air conditioning conditions (summer, winter, transition season), and three different operation adjustment methods have been proposed corresponding to each air conditioning condition, which will reduce the energy consumption of air conditioning system. [ABSTRACT FROM AUTHOR]

Air-conditioning (AC) is discontinuously used in Shanghai residential buildings during the winter time. The AC usage pattern, therefore, has great influence on its energy consumption. In order to figure out the space heating energy consumption for Shanghai residents, it’s necessary to have an accurate description of AC usage model. In this study, questionnaire surveys and continuous measurements of 10 residents were done in Shanghai. Based on the Marcov Chain and AC usage conditional probability model, the descriptive parameters under three different energy levels were calculated according to test data. Then, the AC energy consumption is calculated by DeST-h software for validation. The results of this paper can serve as a reference for AC heating energy consumption studies. [ABSTRACT FROM AUTHOR]

A key aspect of Ground source heat pump (GSHP) is sizing of capacity, which has a signifi-cant influence on energy efficiency, energy consumption and initial investment of system. The capacity of heat pump for residential district should be consistent with cooling and heating load of residential district. However, field measurements and spot interviews indicate that the oversizing issue of GSHP is common for residential district in Hot Summer and Cold Winter zone. The current method of designing the capacity does not take the influence of occupant behavior into consideration. This paper establishes the model by DeST (Designer’s Simulation Toolkits) software considering the different occupant behavior with different Air-conditioning unit (AC) units and it recommends designing the different capacity of the GSHP systems with different types of AC units. [ABSTRACT FROM AUTHOR]

Sizing of air-conditioning water pump systems in buildings is a critical issue in design practice concerning the pump energy consumption in operation and risk of being undersized. As a result, significant energy is often wasted in operation due to oversizing to avoid the risk of being undersized. In current practice, throttling of commissioning valves are commonly adopted to push water flowrate (and pressure head) back to the design point no matter how much oversizing exists in a system. That partly mitigates the oversizing problem. This paper presents a novel approach consisting of probabilistic optimal design concerning uncertainties and on-site adaptive commissioning to further maximize energy savings of constant water flow pump systems. Minimized throttling is achieved by on-site adaptive commissioning, which reduces unnecessary pressure head and significant energy consumption. Pumps selected by the probabilistic optimal design can operate under both conventional design conditions and the projected possible off-design (oversized) conditions. The projection is based on the probability distribution of actual pressure head, which is estimated using Monte Carlo simulation by quantifying uncertainties in pressure loss calculation and system construction. Three case studies are conducted to test and validate this new design and commissioning approach. Results show that about 20% energy saving could be achieved, when the system is oversized by 20%, compared to conventional design and commissioning methods. The proposed approach also offers better energy performance in general compared to the designs all using variable speed pumps. [ABSTRACT FROM AUTHOR]

Accurate modelling and prediction of energy consumption of the air conditioning system is crucial for improving decision making. A method for predicting the energy consumption of air-conditioning systems is proposed in this paper. Based on the same weather type (sunny, cloudy, overcast, or rainy) and day type (workdays or holidays), the similarity errors using the combined weight method and the baseline errors of similar working conditions are calculated with this method. These conditions include outdoor temperature and lighting and plug power, then, similar days are determined within a certain similar error range. In addition, the air-conditioning energy consumption in these similar days is regarded as that in the predicted days. The similarity errors in selecting similar days are acquired by efficiently combining subjective weights, objective entropy weights, and correlation coefficients. To verify the accuracies of the predicted energy consumption using similar days method based on combined weights, a simulation was performed by eQUEST. According to the simulation example of measured data in an office building, it is proved that the proposed prediction method with high forecast accuracy can select similar days with a high degree of similarity under non-catastrophic weather conditions, and offer promise for wider engineering application. [ABSTRACT FROM AUTHOR]

Industry is stuck in reactive mode regarding the maintenance of their heating, ventilation and air conditioning (HVAC) systems, which leads to inefficient operation. To avoid wasteful use of natural resources a proactive approach is needed. To enable this transition combined knowledge-based and data-driven approaches such as the Industrial Data Analysis Improvement Cycle (IDAIC) framework have been proposed, but there is a lack of practical implementation in the literature. In this paper, we implement the IDAIC framework on an Air Handling Unit (AHU) in a real industrial facility to address the lack of practical and reproducible real world analysis. The lack of domain knowledge-driven data mining solutions is addressed primarily in two parts. Firstly, data and control issues are addressed to enable the application of knowledge-based techniques to detect faults that are easily identifiable. Secondly, data-mining based techniques are applied which focus on the detection of more subtle faults which are indicative of component degradation. This approach enabled the development of data-driven analysis that visualises the effect of the different modes of operation on the energy consumption of the AHU, which allow the onsite facilities team to make more informed decisions regarding the maintenance of this AHU. [ABSTRACT FROM AUTHOR]

Generally, conventional controllers for comfort are designed by using on/off control or proportional-integral (PI) control, with little consideration of energy consumption of the system. This paper presents a multi-input-multi-output (MIMO) model predictive control (MPC) for a direct expansion (DX) air conditioning (A/C) system to improve both indoor thermal comfort and air quality, whereas the energy consumption is minimised. The DX A/C system is modelled into a nonlinear system, with a varying speed of compressor and varying speed of supply fan and volume flow rate of supply air being regarded as inputs. We first propose an open loop controller based on an optimisation of energy consumption with the advantage of a unique set of steady states. The MPC controller is proposed to optimise the transient processes reaching the steady state. To facilitate the MPC design, the nonlinear model is linearised around its steady state. MPC is designed for the linearised model. The advantages of the proposed energy-optimised open loop controller and the closed-loop regulation of the MIMO MPC scheme are verified by simulation results. [ABSTRACT FROM AUTHOR]

This paper proposes a gravity heat pipe exchanger used for cooling the communication base station to replace the traditional air conditioning system during winter and transition seasons. Tests were conducted on a commercial available gravity heat pipe exchanger. The experiment was performed to study the effects of the air flow rate and temperature on the cooling capacity, the heat transfer unit number (NTU) and cooling efficiency of the heat pipe exchanger. The results showed that the larger the air flow rate, the smaller the NTU and the larger the cooling capacity. Based on the analysis of the experimental data, it proved that the gravity heat pipe exchanger could reduce running time and operating cost of air conditioning system. According to the practical applications, the yearly cooling loads of a typical communication base station were further calculated for five typical cities which represent the five climatic zones of China. The results validated that the energy saving by using the gravity heat pipe exchanger is significant. The highest annual electricity-saving rate is achieved by Kunming, about 48.6%, while the lowest annual electricity-saving rate is obtained in Guangzhou, about 18.7% among the five climatic zones. The fitted correlation of cooling capacity in term of outdoor temperature is generic to evaluate approximately the performance of applying the gravity heat pipe exchanger in the actual applications subject to various outdoor temperatures. [ABSTRACT FROM AUTHOR]

In a central heating, ventilation, and air conditioning (HVAC) system, the set-points for several local control loops have a significant influence on the overall energy performance of the system. Real-time optimization (RtOpt) of those set-points has therefore been widely studied. However, due to the nonlinear dynamics of the HVAC system as well as the constraints associated with the system operation, real-time optimization always suffers from a heavy on-line computational load when those set-points are optimized simultaneously. To overcome this problem, multiplexed real-time optimization (MRtOpt) has been developed, which optimizes only one set-point at a time but with a faster optimization frequency. Because frequently resetting the set-points introduces artificial disturbances into the local control loops and may deteriorate the system stability, this paper presents a study to enhance the system stability of the multiplexed real-time optimization by integrating a degree of freedom (DOF) based set-point reset to renew the set-points instead of the conventional step-change set-point reset. The control performance of the integrated strategy was investigated using case studies. The results showed that around 10% of the energy saving was achieved by the proposed method compared with a method without real-time optimization. When compared with the conventional real-time optimization method, the proposed method resulted in around 70% computational load reduction, and over 26% reduction in the tracking errors of the local control loops. [ABSTRACT FROM AUTHOR]