Search

The paper confirms that removing antiparallel silicon carbide (SiC) Schottky barrier diodes (SBDs) from SiC-based inverters offers positive effects without critical impact on inverter loss and electromagnetic interference (EMI) issues, moreover, the removal of SBDs reduces the inverter losses in many cases and noise emissions. This conclusion leads to the possibility to improve the power densities by removing SBDs. However, the removal of SBDs may cause some disadvantages such as an increase of the reverse conduction loss and influence of the body diode recovery phenomenon. Therefore, a comprehensive investigation of these advantages and disadvantages is necessary. In this paper, design criteria are proposed to clarify the conditions in which SiC-based inverters without SBDs have advantages over those with SBDs from the viewpoint of losses. On the other hand, to achieve the removal of SBDs, it is also necessary to confirm that removing SBDs does not cause severe EMI issues. The paper confirms that switching noises are reduced by the removal of SBDs; this is due to the larger damping effect of the SiC mosfets without SBDs than that of SiC mosfets with SBDs. The validity of the theoretical analyses and design criteria is confirmed with comprehensive experimental results. [ABSTRACT FROM AUTHOR]

The demand for multitasking GPUs increases whenever the GPU may be shared by multiple applications, either spatially or temporally. This requires that GPUs can be preempted and switch context to a new application while already executing one. Unlike CPUs, context switching in GPUs is prohibitively expensive due to the large context states to swap out. There have been a number of efforts on reducing the overhead of preemption, through reducing the context sizes or overlapping context switching with execution. All those techniques are reactive approaches, meaning that context switching occurs when the preemption request arrives. In this paper, we propose a dynamic and proactive mechanism to reduce the latency of preemption. We observe that kernel execution is almost always preceded by known commands in both CUDA and OpenCL implementations. Hence, a preemption can be anticipated before the actual request arrives. We study such lead time and develop a prediction scheme to perform an early state saving. When the actual preemption is invoked, an incremental update relative to the previous saved state is performed, much like the conventional checkpointing mechanism. Our design can also choose to drain or checkpointing dynamically and accurately according to the feature of kernels in the runtime. This design effectively reduces the stall time of the preempting kernel due to context switching by 58.6%. Moreover, through careful handling of the saved state, we can also reduce the overall size of saved state by an average of 23.3%, compared with a full context switching. [ABSTRACT FROM AUTHOR]

The main drawbacks of conventional direct torque control (DTC) drives are erratic switching frequency and high torque ripples. The multilevel inverter fed DTC drives are proved to be an alternative for eliminating these drawbacks. Apart from the commonly used three-level inverter fed drives, this paper presents an even-level inverter fed DTC drive. In this paper, a space vector modulated DTC algorithm for a four-level DTC drive is proposed and is implemented by feeding both ends of an open-end-winding induction motor with two-level inverters. The space vector modulation (SVM) algorithm uses a fractal based design for switching voltage vector generation and allied computations are performed in 60 degree co-ordinate system. Representation of vectors as integer values in 60 degree co-ordinate planes avoids fractional arithmetic, which simplifies the algorithmic computations. Detailed analyses of the drive performance under dissimilar operating modes are presented. The loading performance of the drive is experimentally verified on a 5-HP induction motor with a strain gauge type mechanical loading system. No-load experimental results were obtained from a laboratory model 2-HP induction motor drive operated in closed loop mode. [ABSTRACT FROM AUTHOR]

Partial shading condition drastically reduces the maximum power output of photovoltaic array. Partial shading occurs due to several factors, such as flying birds, trees, and passing clouds. Many ways can be mitigated partial shading problems in photovoltaic (PV) array. One among the way is reconfiguration techniques, namely reconfigure the location of PV modules in PV array based on irradiance levels in order to distribute shading effects and increasing maximum power. This paper proposed an optimal SuDoKu reconfiguration pattern for $9\times 9$ total-cross-tied (TCT) PV array to improve maximum power under partial shading conditions. In this approach, the physical location of PV modules in TCT array are rearranged based on optimal SuDoKu style without altering the electrical connections, so that the shading effects can distribute over the array. Further, the performance of proposed pattern investigated with existing SuDoKu pattern under different shading conditions by comparing the global maximum power point, mismatch losses, fill-factor, and efficiency using MATLAB-Simulink. Based on the results of this paper, it concluded that the proposed optimal SuDoKu reconfiguration arrangement is reducing the wiring arrangement and increasing the shading distribution over the array as compared to SuDoKu arrangement. [ABSTRACT FROM AUTHOR]

This paper presents an FPGA-based Digital Real-Time Simulation (DRTS) environment for the analysis of Electromagnetic Transients (EMTs) of power systems that include multiple Power Electronic Converters (PECs). The main features of the proposed DRTS platform are that it i) employs two-value resistor switch model for PECs and thus avoids inaccuracies of Associate Discrete Circuit (ADC) model and ii) does not require separation of PECs by transmission lines (stub lines) and thus accurately represents PECs in close electrical proximity of each other. These features respectively result in a time-variant and large system admittance matrix which significantly increases the computation burden in each simulation time-step and can render it infeasible for real-time applications. To overcome this problem this paper introduces i) Switching-Network Partitioning (SNP) method which is tailored for PECs representation in FPGA and ii) Reformulated Modified Nodal Analysis (RMNA) method to enable computational parallelism between the solution of network and component models in FPGA. SNP enables solution-level partitioning of the PECs and the rest of the system. The developed DRTS platform enables sub-microsecond simulation time-step and provides a fixed hardware irrespective of the system configuration. Performance of the platform is evaluated for a study system and verified versus off-line simulation studies. [ABSTRACT FROM AUTHOR]

In this paper, an overload and short-circuit protection method is proposed for voltage source inverter-based uninterruptible power supply (UPS) system. In order to achieve high reliability and availability of the UPS, short circuit and overload protection scheme are necessary. When overload or short circuit happens, using the proposed control method, the amplitude of the output current can be limited to a constant value, which can be set by the customer to avoid the destruction of the power converter, and to obtain a faster recovery performance as well. The detailed principle of the proposed protection method is discussed in this paper. It mainly contains three parts in the control diagram for current limit, first is the anti-windup in the voltage and current controllers, then the feedforward of the capacitor voltage to the current control loop, the last is the fast reset of the resonant part of the current controller when overcurrent happens. The procedure of developing the control method is also presented in the paper. Experimental results on a commercial UPS system are presented to verify the effectiveness of the control method. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are playing a pivotal role in the power sector with potential applications, such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost, and higher efficiency compared with their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level voltage-source inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the dc-link capacitors and FCs. The generation of various output voltage levels and the limitation of the sinusoidal pulsewidth modulation control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared with the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique. [ABSTRACT FROM AUTHOR]

This paper presents a novel control strategy to significantly reduce the high-frequency transformer loss in a modular solid-state transformer (SST) based converter system. The modular SST design is based on an ac–dc power-electronic building block comprised of an H-bridge at the ac input and a bidirectional soft-switching isolated dc–dc converter with a medium-voltage insulated high-frequency transformer. The ac terminals of input H-bridges are connected in series and directly coupled to the medium-voltage ac line, while the output dc terminals are all connected in parallel at a low voltage. The key innovation described in this paper, without sacrificing the output performance, is the control scheme that reduces core and winding losses associated with the dc–dc resonant stage by turning off the selected dc–dc converters in synchronism with the line voltage. The prototype for the test described in this paper is based on a modular SST where each module is rated at 50 kVA, with a 200 kHz transformer using 1.7 kV silicon carbide discrete mosfets, but the described control concepts are more broadly applicable to similar topologies. [ABSTRACT FROM AUTHOR]

This paper deals with a multilevel ac–ac double conversion system that uses the intercell transformer (ICT) for applications which include generating systems and the interfacing of renewable energy sources with the utility grids. Each phase of the proposed configuration is formed through the ICT interleaving operation of two multilevel 5-level E-type legs to achieve the 3-phase 5-level back-to-back E-type converter (3Φ5L BTB E-type converter). The analytical procedure to select the inductance and capacitance values of both the input and output filters is described in the paper. Furthermore, the design and implementation of the input/output ICTs and inductors is discussed. The simulation and the experimental results on the 20-kVA interleaved 3Φ5L BTB E-type converter prototype are presented to validate the proposed analysis. [ABSTRACT FROM AUTHOR]

With the rapid development of photovoltaic and fuel cell stacks, high voltage gain converters are urgently demanded. Conventional boost is limited by the exaggerated duty cycle, it is impossible to obtain a high voltage gain while ensuring efficiency. Therefore, a zero-voltage switching (ZVS)-modified SEPIC converter that combines a voltage multiplier cell with traditional SEPIC is proposed in this paper. With detailed parameters design process, this presented converter works at zero voltage switching (ZVS), while obtaining high voltage gain without extremely high duty cycle. Besides, voltage stress is also reduced and low-voltage component with lower parasitic parameters can be used, thus efficiency is maintained. In order to further improve the power density, an integrated inductor scheme is adopted in this paper without changing intrinsic working states of the two inductors. A 36-W prototype is built, and experiments are conducted to verify the advantages of the proposed converter. The efficiency is up to 91.5% at full load. [ABSTRACT FROM AUTHOR]

The flexibility in transmission networks is not fully utilized in existing energy management systems (EMSs). Corrective transmission switching (CTS) is proposed in this two-part paper to enable EMS to take advantage of the flexibility in transmission systems in a practical way. This paper proposes the following two EMS procedures: first, Procedure-A connects real-time security-constrained economic dispatch (RT SCED) with real-time contingency analysis (RTCA), which is consistent with industrial practice; and second, Procedure-B, an enhanced version of Procedure-A, includes CTS in EMS with the proposed concept of branch pseudo limit used in RT SCED. Part-I of this paper presents the methodology, whereas Part-II includes detailed results analysis. It is demonstrated that Procedure-A can effectively eliminate the base case overloads and the potential post-contingency overloads identified by RTCA, and Procedure-B can achieve significant congestion cost reduction with consideration of CTS in RT SCED. Numerical simulations also illustrate that integrating CTS into RT SCED would improve social welfare. [ABSTRACT FROM AUTHOR]

Contribution: This paper introduces the real-world limitations and non-technical aspects of power electronics (PEs) projects to students through innovative tutorial activities. Background: Many electrical engineering curricula offer a PE courses (PECs) for third- or fourth-year undergraduate students. Prior research on PEs education mainly focused on improving students’ experimental skills through developing practical experiments, laboratory activities, and problem/project-based learning. An instructional approach that instead employs real-world knowledge and skills is worth evaluating. Intended Outcomes: Students should be able to consider real-world technical and non-technical limitations when applying theory to design PE circuits and converters, and be able to select and carry out appropriate tests to troubleshoot circuits. Application Design: Prior research on engineering education emphasized the importance of introducing real-world limitations to the students as part of their curriculum. This paper suggests that the tutorial activities presented in a PEC can help students acquire skills in designing and troubleshooting a circuit or system according to desired technical aspects, real-world limitations, and available data. Findings: Evidence of the validity of this approach in a PEC at two Australian universities, over four academic years, is provided. Students receiving the new tutorial activities had percentage scores some 10–15 points higher than those who had traditional tutorials. Another evaluation reveals the students’ vibrant participation in the activities during the new tutorial sessions. [ABSTRACT FROM AUTHOR]

This paper presents a self-learning strategy to control the deactivation of cylinders in large displacement automotive engines. Cylinder deactivation is a useful strategy to reduce emissions and improve fuel consumption without limiting the maximum engine power. A cylinder deactivation algorithm has to balance the target of reducing emissions with drivability concerns. Changing the cylinder configuration at the wrong time or too often negatively affects drivability and fuel efficiency. The paper proposes a self-learning algorithm inspired by the Markov Chain formalism. The proposed algorithm predicts the future fuel consumption and determines the best cylinder configuration based on that prediction. The prediction algorithm is learnt online using past inputs and thus adapts to the specific driver and conditions. Two versions of the algorithm are proposed that use two different inputs. The approaches are validated in simulation on an engine test-bed, showing that the self-learning algorithm yields fuel savings up to 10% without affecting drivability in the New European Driving Cycle. [ABSTRACT FROM AUTHOR]

Resource allocation in mmWave small cell is a key issue of the fifth generation (5G) systems. To solve this problem, we first present a hybrid beamforming structure for base station of small cell, which consists of orthogonal frequency division multiplexing (OFDM), identity matrix and switched-beam. Next, we formulate the joint allocation of the beam and transmitted power on the sub-carriers into a mixed integer non-linear programming problem (MINLP). Due to the non-convexity of this problem, we decompose it into two subproblems which are the beam selection and the power allocation. For the beam selection, we propose an algorithm based on cooperative games. For the power allocation, we present an optimal and sub-optimal solution based on Lagrange duality and non-cooperative games respectively. Simulation results show that the beam allocation algorithm proposed in this paper can effectively improve the sum rate of the system, and the optimal power allocation solution is far superior to the sub-optimal one in sum rate. [ABSTRACT FROM AUTHOR]

Graphene has attracted great interest for its distinctive band structure and physical properties. Results from previous studies show that a graphene cathode can provide stable field emission and intense emission in a vacuum. In this paper, a graphene cathode was fabricated using chemical vapor deposition (CVD) on copper electrodes, and the breakdown of the cathode in a high-pressure gas was studied. A low-jitter, self-breakdown gas spark switch based on a graphene cathode is proposed in this paper. The impulse-breakdown characteristics of this switch in a quasi-uniform electric field were studied. When the gap length is 5 mm, and the gas pressure is 0.6 MPa, the average breakdown voltage ($U_{\mathrm {BD}}$) is nearly 85.9 kV, and the voltage jitter is only 3.2%; these values are much lower than those for pure copper cathodes and graphite cathodes. The graphene cathode is found to be a suitable choice for use as a high-power gas switch in applications requiring an intense emission source. [ABSTRACT FROM AUTHOR]

This paper presents a balancing algorithm for the so-called Director Switch, a controlled, reverse conducting, self-powered, high-voltage switch, using series-connected insulated gate bipolar transistors (IGBTs). This is a key component on two new voltage-source, high-voltage direct current (HVDC) converter topologies. These, which promise efficiency, cost, and size reductions, are an alternate arm converter and a series bridge converter. One of the main design challenges of the director switch is how to supply the IGBT gate drivers, and other auxiliary electronics while overcoming the high-voltage insulation barrier to ground level. In this paper, this is achieved by using the energy stored in a capacitive clamp snubber circuit, which also helps with the overvoltage mitigation during rare hard-switching events. However, the clamp capacitor and by proxy the IGBT voltages become highly unbalanced during operation, compromising the integrity of the switch. This paper presents a balancing strategy that consists in applying a controlled delay in the switching of the IGBT levels, in a way that forces a voltage balance on all the switch levels. The paper explains the unbalance. Then, the balancing strategy is explained and validated on simulation and on a high-voltage experimental rig, on switches comprising two and three series-connected IGBTs, respectively. [ABSTRACT FROM AUTHOR]

This paper presents a neutral-point deviation and ripple compensating control method applied to a three-level neutral-point-clamped (NPC) converter. The neutral-point deviation and its harmonic components are analyzed with a focus on the average current flowing through the neutral-point of the dc link. This paper also proposes a control scheme compensating for the neutral-point deviation and dominant harmonic components under generalized unbalanced grid operating conditions. The positive and negative sequence components of the switching functions and ac input currents are employed to accurately explain the behavior of three-level NPC converter. Simulation and experimental results are presented to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

A high-frequency high voltage gain discontinuous conduction mode coupled-inductor boost LED driver based on planar component is presented in this paper. GaN switch is adopted with lower conducting resistance and higher switching speed. Zero voltage switching (ZVS) is achieved at the same time to reduce high switching loss caused by high switching frequency. Compared with the previous work, the voltage gain is higher and efficiency is higher because of ZVS. This paper focuses on high efficiency; therefore, resonant gate driver is adopted and efficiency is increased by 0.6%. In terms of the coupled-inductor, planar component is used and parameter optimization is also proposed to realize lower loss, including wingding loss and fringing loss caused by the air gap. A 500 kHz 36 W prototype has been designed to demonstrate theoretical analysis. In addition, comparison of drive loss between the resonant gate driver used in this paper and conventional driver implemented by Si8271 is made, revealing advantages of the resonant driver. Obtained efficiency was up to 92.1% at full load. [ABSTRACT FROM AUTHOR]

The use of electronic equipment and other dc-compatible appliances in homes and offices is increasing at a very fast rate, as well as the distributed generation of energy. These two statements will most likely trigger, in a near future, the adoption of district-scale dc grids, connecting dc microgeneration plants and consumers, in an effort to cut the number of conversion steps required to deliver power to dc appliances. DC–DC converters will be fundamental in these systems, allowing the establishment of several voltage levels. The reliability of these converters plays a critical role, ensuring service continuity of the loads connected to them. With the increment of reliability in mind, this paper proposes a simple yet effective open-circuit fault diagnostic method suitable for interleaved dc–dc boost converters, but equally functional for other dc–dc converter topologies. The improvements introduced in this paper greatly simplify the diagnostic action, while making the correct diagnostic of faults independent of the switching duty cycle. Moreover, an alternative reconfiguration scheme is proposed to mitigate the adverse impacts of such faults. To prove the effectiveness of these strategies, a three-phase interleaved boost converter prototype was used in the experiments. [ABSTRACT FROM AUTHOR]

In this paper, two novel $4 \times 6$ filtering Butler matrices with uniform and nonuniform power distribution are proposed. The matrices, consisting of a network of coupled resonators and two phase shifters, provide power division and phase shift together with a bandpass transfer function. The analytical synthesis procedures for the $4 \times 6$ filtering Butler matrices are presented. To verify the concept experimentally, two $4 \times 6$ filtering Butler matrices, operating at 2.4 GHz, with uniform and nonuniform power distribution are designed, fabricated, and measured. Simulated and measured results are found to be in good agreement with each other. Multibeam antenna arrays are realized by using the Butler matrix, and the theoretical analysis has been confirmed by measurements of multibeam antenna arrays, which show reduced sidelobe level (SLL). [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

The application of Hall-based BLDC motors ranges from automotive accessory components such as oil and water pumps to high speed compressors. This paper proposes a new twelve-step unsymmetrical 160° commutation strategy using a single Hall-effect sensor method for brushless DC (BLDC) motor drives. The signal from the Hall-effect sensor is used to generate a number of pseudo Hall signals via a proposed speed-position estimator. The pseudo signals are then employed to control switching logic of a voltage source inverter (VSI). The effectiveness of the single Hall sensor method is examined on the unconventional 160° strategy, and on conventional 120°, 150° and 180° strategies with promising results. The paper presents a detailed comparison of the twelve-step unsymmetrical 160° commutation strategy with six-step voltage space vector that is used in conventional 120° and 180° strategies, and twelve-step symmetrical voltage space vector that is used in 150° strategy. Simulation results are validated via experimental measurements on a laboratory set-up using a real time dSPACE control environment, a representative BLDC motor prototype, a VSI and associated control components. [ABSTRACT FROM AUTHOR]

This paper presents a simple pulse width modulation algorithm for control of an ultracapacitor based energy storage system used for source and load support applications. As opposed to dual loop control philosophy that is widely used for backup applications, this paper presents a simple single loop current control that is only useful for controlling the ultracapacitor based DC/DC converters used in source and load support applications. The proposed PWM blocking method necessitates the DC/DC converter to operate in five states and takes into consideration the essential operational limits associated with the ultracapacitors. The performance of the proposed algorithm is verified experimentally using a 24 V laboratory prototype setup. Further, the shortcomings of dual loop control when applied to source and load support applications are demonstrated. [ABSTRACT FROM AUTHOR]

This paper presents a simplified implementation technique for direct torque control (DTC) of asymmetric six-phase induction motor drive. Current harmonics of fifth and seventh order are observed in the phase currents if conventional DTC scheme is extended for the asymmetric six-phase machine. These harmonic components are not responsible for torque production, thus causing losses in the motor winding. Synthetic vectors are generally used for reduction of current harmonics. Average voltage in $xy$ subspace is maintained to zero by synthetic vectors leading to reduction of currents in $xy$ subspace. A simplified method of implementation of synthetic vectors is proposed in this paper, which eliminates the need for designing of switching sequence and requirement of field-programmable gate array. Also, the number of synthetic vectors that can be possibly produced is increased compared with the ones developed by techniques available in the literature. The experimentation is carried out on a laboratory-developed prototype and the experimental results are presented in this paper to verify the proposed scheme. [ABSTRACT FROM PUBLISHER]

Magnetic tunnel junction (MTJ)-based devices have been studied extensively as a promising candidate to implement hybrid energy-efficient computing circuits due to their nonvolatility, high integration density, and CMOS compatibility. In this paper, MTJs are leveraged to develop a novel full adder (FA) based on 3- and 5-input majority gates. Spin Hall effect (SHE) is utilized for changing the MTJ states resulting in low-energy switching behavior. SHE-MTJ devices are modeled in Verilog-A using precise physical equations. SPICE circuit simulator is used to validate the functionality of 1-bit SHE-based FA. The simulation results show 76% and 32% improvement over previous voltage-mode MTJ-based FA in terms of energy consumption and device count, respectively. The concatanatability of our proposed 1-bit SHE-FA is investigated through developing a 4-bit SHE-FA. Finally, delay and power consumption of an n -bit SHE-based adder has been formulated to provide a basis for developing an energy efficient SHE-based n -bit arithmetic logic unit. [ABSTRACT FROM PUBLISHER]

Scan-based tests that maintain close-to-functional operation conditions are important for avoiding overtesting of delay faults while achieving the fault coverage required for avoiding test escapes. For a measurable proximity to functional operation conditions, partially functional broadside tests have a known Hamming distance between their scan-in states and reachable states. Another parameter that is important for the discussion of overtesting is the switching activity. This paper suggests a combined metric, where a reduced switching activity is taken as a safety margin that allows a higher Hamming distance between the scan-in state and a reachable state. The metric is defined such that a value of 100% or lower is preferred. To demonstrate that the metric is flexible enough to allow tests to be generated, the paper describes a test generation procedure that uses the metric. [ABSTRACT FROM PUBLISHER]

This paper focuses on the design, performance modeling, and evaluation of probabilistic logic using superparamagnetic nanomagnets for which there exists a strong interplay between deterministic dynamics and intrinsic thermal noise. The switching element in the spin domain is chosen as the giant spin-Hall effect (GSHE) device that operates based on the dipolar coupling phenomenon in a two-magnet system to achieve low-energy ( $\approx ~1.3$ fJ/b) and low-power ( $\approx ~0.5~\mu $ W) switching characteristics. The use of spin currents on the order of a few tens of mA/ $\mu $ m2 in the subcritical regime to operate the GSHE device yields nondeterministic switching behavior with probability of correctness less than 100%. Therefore, the proposed technique allows us to trade off circuit accuracy for tremendous reduction in energy and power dissipation. In this paper, we identify the required dimensions and material parameters of the read–write units to ensure robust magnetic dipolar coupling for reliable operation of the GSHE switch. Then, through Monte Carlo simulations, we evaluate the probabilistic switching behavior of the GSHE switch as a function of the input spin current amplitude and pulsewidth for various orientations of the magnetization vectors. The delay of the GSHE switch is quantified using a probability distribution function owing to the randomness imparted to the dynamics by intrinsic thermal noise of the nanomagnets. The relationship between the probability of correctness and the energy dissipation of the GSHE switch is quantified. The results are extended to evaluate the performance and circuit error rate of complex logic gates, such as NAND and NOR, constructed using the GSHE switch. It is shown that unlike the probabilistic CMOS (PCMOS) logic, the circuit error rate in the GSHE logic becomes a function of the input vector combination and the prior state of the switch. These nuances are captured in the compact model of the circuit error rate of multiple-input GSHE logic developed in this paper. The performance of the probabilistic GSHE logic is compared with that of PCMOS logic at the 14 nm technology node. Since the noise generation process in PCMOS logic has a limited bandwidth of tens of megahertz and consumes tens of microwatt power, the peripheral circuitry becomes prohibitive. By utilizing the inherent thermal stochasticity, nanomagnets provide a clear advantage to implement probabilistic computing platform targeted toward error-tolerant applications such as those from the image processing and machine learning domains. [ABSTRACT FROM AUTHOR]

This paper presents the effect of stray capacitances in bipolar (negative and/or positive) pulses generated by the two different topologies of the solid-state Marx modulators. According to the analysis, the stray capacitances influence the energy transfer from the Marx modulator capacitors to the load affecting the bipolar (negative and/or positive) pulse rise time. This paper deals with the structure design to reduce the influence of the stray capacitance and to improve the pulse rise time of these bipolar solid-state Marx modulators. A four-stage laboratory prototype of the two topologies has been assembled using 1200-V insulated gate bipolar transistors and diodes, operating with 1000-V dc input voltage and 1-kHz frequency, producing 4-kV bipolar pulses, with 5- \mu \texts pulse duration and 120-ns rise time, into a resistive load. [ABSTRACT FROM PUBLISHER]

This paper presents an advanced technique for calculating activation energy of oil-impregnated pressboard through dielectric response current measurement under switching impulse voltage at different temperatures. The proposed technique analyzes the measured impulse voltage and current signals to formulate its equivalent circuit at different temperatures. The equivalent circuit parameters are utilized to determine the shifting of ac conductivity curve along frequency axis with variations in temperatures. Based on the shifted ac conductivity curves at different temperatures, the corresponding activation energy of the insulation is estimated. The effectiveness of the proposed technique is investigated through a few laboratory prepared test samples. [ABSTRACT FROM AUTHOR]

Service restoration is one of the critical functions to enable the future self-healing distribution system. To restore the distribution system in a timely and reliable manner, the realistic system operating conditions need to be accurately characterized. In this paper, two main factors that have great impacts on distribution system restoration (DSR) in practice are investigated. First, cold load pickup (CLPU), generally caused by thermostatically controlled loads (TCLs), is a common phenomenon after an outage and shaped by the outage duration. However, the time-dependent behaviors of CLPU are rarely considered in literature. In this paper, the operating state evolution of TCLs after an outage is analyzed to characterize time-dependent CLPU. And the time-dependent CLPU is analytically embedded in DSR to accurately represent the actual behaviors of the restored loads. Second, it is difficult to predict loads that fluctuate during DSR due to the lack of real-time measurement data. Accordingly, a robust DSR based on the information gap decision theory (IGDT) is proposed to address this challenge, fully considering the uncertainty of CLPU. The proposed models are tested in IEEE 13-node and 123-node test feeders. Simulation results demonstrate that the time-dependent CLPU model and the uncertainty modeling of CLPU can accurately capture the actual behaviors of loads with TCLs after an outage, which greatly improves DSR decisions in practice. [ABSTRACT FROM AUTHOR]

Since the inherent nature of many applied high-technological systems and networks possesses switching behaviors, modeling, controlling, and stabilizing problems of the switching plants are becoming as the important research scenarios in the current literature. Moreover, consideration of the effects of mismatching uncertainties along with matching uncertain parts as well as unknown dynamics is a significant topic in the control engineering community. As a result, this paper is dedicated to the controlling problem of partially unknown nonlinear switched systems whose dynamics are perturbed by both matched and mismatched uncertainties. In addition, since the existence of gain deviations in real-world implementations of physical actuators can lessen the control act of the switching system, this paper handles the corresponding gain variations in the control inputs via some adaptation variables. In the design procedure, no limiting supposition is made for the switch signal of the switched plant. The proposed control algorithm is based on the variable structure control theory in which the selected sliding surface is able to deal with mismatching uncertainties and the deriving control law is robust against the lumped uncertain components. As a contribution, the Lyapunov functions are built such that not only to provide an asymptotic stable system but also to assure the global (practical) finite-time stability of the equilibrium state of the final closed-loop cascade switched plant. The robust performance of the developed control strategy is confirmed via two illustrative examples. [ABSTRACT FROM AUTHOR]

This paper presents a new soft switching high voltage gain interleaved dc-dc converter with a three-windings coupled inductor for a fuel cell vehicle. Two interleaved and intercoupled boost cells are connected by the input parallel and output series (IPOS) configuration, realizing low input current ripple and high voltage gain simultaneously. All power switches can operate under soft switching conditions by only adding a simple auxiliary circuit composed of one auxiliary inductor and one power switch. Besides, the auxiliary inductor is coupled with the main inductors, which results in a rapid zero convergence of the auxiliary current and a small conduction loss of the auxiliary circuit. The operating principle, steady state characteristic, comparison with other converters, and parameter design are analyzed in this paper. Finally, the main characteristics of the proposed converter are verified by a 1-kW laboratory prototype. [ABSTRACT FROM AUTHOR]

This paper summarizes the work performed by the Task Force —within Performance Characteristic Subcommittee of IEEE PES Transformers Committee— to investigate potential revisions to IEEE Std C57.142-2010. Although the scope of this document does not implicitly exclude HV and EHV systems, the existing document primarily includes examples and information on distribution voltage systems. A Task Force was formed to investigate the need to include information about power system transient events on HV systems more explicitly in this existing document. The Task Force was charged with the following tasks:-Establish system voltages encompassed by C57-142-2010 Guide. -Gather field data, reports, and literature on HV and EHV failures related to substation transients and transformer interaction. -Solicit input from the other technical committees on this subject. -Review IEC and CIGRE work in this area. -Recommend course of action on revision of the present Guide. -Recommend high level changes to the Guide. -Prepare final paper for the Subcommittee. In the course of this work several failure scenarios were identified. These are categorized and the failures are described in this paper. The final recommendations to the Subcommittee are summarized and recommendations are presented for the course of action on the revision/addition of HV and EHV material to the current C57.142 Guide. [ABSTRACT FROM AUTHOR]

The hybrid modular multilevel converter (HMMC), consisting of half-bridge and full-bridge submodules (SMs), has become a competitive topology due to the DC fault ride-through capability (FRTC). Redundancy schemes need to be employed to improve the reliability, including fixed-level and voltage-sharing active schemes, as well as passive scheme. However, different schemes affect reliability differently, which entails specific models. The contributions of this paper involve that analytical reliability models of HMMCs are proposed with considerations of voltage stress in active scheme, as well as imperfect bypass switch in passive scheme, and the comparison of different schemes is conducted to help the redundancy design. The reliability of HMMCs is divided into basic and extra components by the requirement of FRTC, which are modeled through the Markov chain and iteration method. A case study is conducted to validate the feasibility and accuracy of the proposed models, and the reliability analysis is presented, together with comparisons of different redundancy schemes. The results illustrate that reliability improvements of both fixed-level mode and passive scheme are prone to suffer saturation effect with the increase of redundant half-bridge SMs, which may even cause reliability decline in voltage-sharing mode. [ABSTRACT FROM AUTHOR]

Severe geomagnetic disturbances (GMDs) increase the magnitude of the electric field on the Earth’s surface (E-field) and drive geomagnetically-induced currents (GICs) along the transmission lines in electric grids. These additional currents can pose severe risks, such as current distortions, transformer saturation and increased reactive power losses, each of which can lead to system unreliability. Several mitigation actions (e.g., changing grid topology) exist that can reduce the harmful GIC effects on the grids. Making such decisions can be challenging, however, because the magnitude and direction of the E-field are uncertain and non-stationary. In this paper, we model uncertain E-fields using the distributionally robust optimization (DRO) approach that determines optimal transmission grid operations such that the worst-case expectation of the system cost is minimized. We also capture the effect of GICs on the nonlinear AC power flow equations. For solution approaches, we develop an accelerated column-and-constraint generation (CCG) algorithm by exploiting a special structure of the support set of uncertain parameters representing the E-field. Extensive numerical experiments based on “epri-21” and “uiuc-150” systems, designed for GMD studies, demonstrate (i) the computational performance of the accelerated CCG algorithm, (ii) the superior performance of distributionally robust grid operations that satisfy nonlinear, nonconvex AC power flow equations and GIC constraints, in comparison with standard stochastic programming-based methods during the out-of-sample testing. [ABSTRACT FROM AUTHOR]

The overhead of memory virtualization remains nontrivial. The traditional shadow paging (TSP) resorts to a shadow page table (SPT) to achieve the native page walk speed, but page table updates require hypervisor interventions. Alternatively, nested paging enables low-overhead page table updates, but utilizes the hardware MMU to perform a long-latency two-dimensional page walk. This paper proposes new memory virtualization solutions based on hardware (machine) mode—the highest CPU privilege level in some architectures like Sunway and RISC-V. A programming interface, running in hardware mode, enables software-implementation of hardware support functions. We first propose Software-based Nested Paging (SNP), which extends the software MMU to perform a two-dimensional page walk in hardware mode. Second, we present Swift Shadow Paging (SSP), which accomplishes page table synchronization by intercepting TLB flushing in hardware mode. Finally we propose Accelerated Shadow Paging (ASP) combining SSP and SNP. ASP handles the last-level SPT page faults by walking two-dimensional page tables in hardware mode, which eliminates most hypervisor interventions. This paper systematically compares multiple memory virtualization models by analyzing their designs and evaluating their performance both on a real system and a simulator. The experiments show that the virtualization overhead of ASP is less than 4.5% for all workloads. [ABSTRACT FROM AUTHOR]

This paper presents frequency domain (FD) Norton-type equivalents of single- and three-phase photovoltaic (PV) generators, aimed at transient calculations. The proposed equivalents can be interfaced with a general frequency-dependent network and/or nonlinear loads and include voltage/current sources representing initial conditions aimed at partitioned-time transient simulation. The transient solution is performed via the numerical Laplace transform (NLT) in a sequential scheme by using time sub-windows with corresponding initial conditions and using reduced number of samples. The proposed approach overcomes the issue of computationally heavy simulations as in classical implementations of NLT. Two case studies involving PV generator and nonlinear load are presented to illustrate the performance of the proposed FD PV models. [ABSTRACT FROM AUTHOR]

To calibrate non-contact sensors with fast response and high scale factor, it is critical to develop step pulse generators capable of generating standard high voltage step pulses and accurately measuring the generated waveform. In this paper, two types of step pulse generators are designed with output voltages of 2 kV and 100 kV. The 2 kV step pulse generator can generate a step pulse with a rise time of ∼300 ps and an adjustable pulse width. A step pulse with a rise time less than 5 ns and a pulse width over 1 μs can be generated with the 100 kV step pulse generator. The uncertainty of 2 kV step pulse generator is then analyzed by simulations and experiments. Finally, a performance comparison with step pulse generators in previous studies is carried out. Bandwidth, linearity and repeatability of the sensors can be verified with the designed two step pulse generators. [ABSTRACT FROM AUTHOR]

The safety of converters is key to the stable operation of AC/DC hybrid power grids after AC faults. Thyristor valve current is a direct manifestation of the converter observability, but there are no measuring elements inside the converter, so the thyristor valve current can be reflected only indirectly through external electrical quantities. This paper proposes a virtual measurement scheme based on the temporal features of the converter terminal current. First, under the action of the trigger pulse, the polarity characteristics of the AC current and temporal features between the valves are utilized to predictive estimate the valve state. Then, when commutation failures occur and the bypass paths form, the conduction state of valve is constructed based on the relationship between AC and DC current. Last, when the valve is to be shut-off in the bypass path, the blocking state of the valve is corrected based on the unidirectional conductance characteristics of the valve. According to the above analysis, combined with the topological current equation of the converter, the valve current can be calculated in the whole process. Through the simulation of the different valve states and bypass paths and analysis of the field record data, the results show that the valve current can still be accurately calculated based on the virtual measurement scheme. [ABSTRACT FROM AUTHOR]

Multiphase drives with fault-tolerant capability are favored in high-reliability applications. In most fault-tolerant multiphase drives, the fault types and locations must be known prior to the fault-tolerant control. Therefore, fault diagnosis is an indispensable procedure. This paper proposes a generalized method to detect and identify the open-circuit faults (including open-switch and open-phase faults) in star-connected symmetrical multiphase drives with different phase numbers. The selected fault diagnosis signals are calculated solely from simple arithmetical operations of measured phase currents, resulting in easy real-time implementation. As fault detection signals are derived from the physical constraint imposed by the neutral point, the proposed method is naturally robust and not sensitive to operating points, machine transients and harmonics in stator currents. Therefore, a relatively small fault detection threshold can be used and fast detection can also be achieved. After the fault has been detected, the fault type is further identified according to the polarity of the integration of phase currents. Experimental results on nine-phase and five-phase induction machine drives verify the generality, fast diagnosis speed and robustness of the proposed method. [ABSTRACT FROM AUTHOR]

The paper develops two computationally efficient models, namely a detailed equivalent model and an average-value model, with provisions for representation of the critical state of converter blocking, for modular multilevel converters with embedded storage. These models are indispensable in the simulation of dc faults. The developed detailed equivalent model provides accuracy that matches electromagnetic transient (EMT) simulations, with much reduced computational burden; the developed average-value model represents the averaged behavior of the converter by neglecting switching transients. Both models are extensively evaluated in the context of an HVDC system against benchmark results form a detailed switching model developed in PSCAD/EMTDC. The results confirm the validity and accuracy of the models for steady state, transient, and faulted operating conditions including when the converter is blocked in response to a dc fault. [ABSTRACT FROM AUTHOR]

This paper focuses on the issue of network connectedness (NC) in security-constrained optimal transmission switching problems, which is complicated by branch contingencies and corrective line switching. Two criteria are firstly proposed with the principle of preserving NC as much as possible within reasonable limits. By extending the electrical flow based NC constraints, a proposition is derived to associate different cases of NC with the optimum of a linear program, yielding the mathematical formulation of the NC criteria. By Karush-Kuhn-Tucker conditions, this formulation is further transformed into a tractable version which can be incorporated with existing SCOTS models without affecting the applicability of original solution approaches. Finally, case studies on various networks and SCOTS models demonstrate the efficacy of the proposed approach. [ABSTRACT FROM AUTHOR]

Magnetic random-access memory (MRAM) is a promising memory technology due to its high density, non-volatility, and high endurance. However, achieving high memory fidelity incurs high write-energy costs, which should be reduced for large-scale deployment of MRAMs. In this paper, we formulate a biconvex optimization problem to optimize write fidelity given energy and latency constraints. The basic idea is to allocate non-uniform write pulses depending on the importance of each bit position. The fidelity measure we consider is mean squared error (MSE), for which we optimize write pulses via alternating convex search (ACS). We derive analytic solutions and propose an alternating water-filling algorithm by casting the MRAM’s write operation as communication over parallel channels. Hence, the proposed alternating water-filling algorithm is computationally more efficient than the original ACS while their solutions are identical. Since the formulated biconvex problem is non-convex, both the original ACS and the proposed algorithm do not guarantee global optimality. However, the MSEs obtained by the proposed algorithm are comparable to the MSEs by complicated global nonlinear programming solvers. Furthermore, we prove that our algorithm can reduce the MSE exponentially with the number of bits per word. For an 8-bit accessed word, the proposed algorithm reduces the MSE by a factor of 21. We also evaluate MNIST dataset classification supposing that the model parameters of deep neural networks are stored in MRAMs. The numerical results show that the optimized write pulses can achieve 40% write-energy reduction for the same classification accuracy. [ABSTRACT FROM AUTHOR]

The physical unclonable function (PUF) is a promising innovative hardware security primitive that leverages the inherent randomness in the physical systems to produce unique responses upon the inquiry of challenges, thus the PUF could serve as a fingerprint for device authentication. In this paper, we propose a novel PUF implementation exploiting the sneak paths in the resistive cross-point (X-point) array, as a hardware security primitive. The entanglement of the sneak paths in the X-point array greatly enhances the entropy of the physical system, thereby increasing the space of challenge-response pairs to make a strong PUF. The X-point PUF characteristics, such as uniqueness and reliability, are experimentally evaluated on the fabricated $12 \times 12$ cross-point arrays based on the Pt/HfOx/TiN structure. The measurement results show that the average inter-Hamming distance of the response bits is around 46.2% across 28 different arrays, showing sufficient uniqueness. The measurement results also demonstrate that 0% intra-Hamming distance (or 100% reliability) of the response bits can be maintained more than 7.2 h at 100 °C (or equivalently ten years at 40 °C). This paper demonstrates the feasibility of using X-point PUF as a lightweight and reliable PUF for device authentication. [ABSTRACT FROM PUBLISHER]

This paper is concerned with the use of a three-level inverter for a synchronous reluctance machine (SynRM). The SynRM suffers from a poor power factor due to poor machine saliency. This makes it harder to operate the three-level neutral-point-clamped inverter due to a strict requirement to have the two dc-link capacitor voltages balanced. This paper proposes a new nearest three vector modulation algorithm which can balance the two dc-link capacitors even at poor machine saliency ratio (poor power factor). In this paper, a method of sizing the two dc-link capacitors based on the machine power is also proposed. A comparison between two- and three-level inverters was conducted. The SynRM registered lower $d$-axis current ripple with a three-level inverter, indicating lower core losses in the machine. [ABSTRACT FROM PUBLISHER]

This paper is concerned with the problem of finite-time H∞ synchronization for a class of discrete-time switched neural networks with quantized feedback controllers. First, we take advantage of mode-dependent average dwell time approach and semi-time-dependent (STD) Lyapunov function method to establish new criteria for the finite-time synchronization. Based on the newly developed criteria, a finite-time bounded real lemma is presented and further, the quantized state feedback controller is designed to ensure the finite-time H∞ synchronization of the underlying neural networks. The conservatism is further reduced by the proposed mode-dependent and STD controller. Finally, we use two illustrative examples to show the effectiveness and superiority of the results obtained in this paper. [ABSTRACT FROM AUTHOR]

The demand for DC gas-insulated switchgear/gas-insulated transmission line (GIS/GIL) becomes more and more urgent in recent years owing to the rapid development of high voltage direct current (HVDC) transmission systems. Insulators in DC GIS/GIL could easily accumulate a large number of charges on its surface during long-term operation, which might lead to overstressing of polymeric insulation or surface flashover. Therefore, it is of great significance to propose an effective method for dissipating extra surface charges. However, achieving charge dissipation without opening the tank is still a great challenge to SFC6-insulated equipment for a long time. In this paper, a novel method, which is named X-ray based non-contact charge dissipation method (XNCDM) for insulators in SF6-insulated equipment, is proposed. The effects of X-ray irradiation on the charges dissipation and the influences of irradiation dose were experimentally investigated in SF6. The mechanisms underlying are discussed in detail. Results show that surface charges on the insulator can be almost completely dissipated after short-time X-ray irradiation with enough dose, owing to the significant enhancement of electric conduction along the insulator surface and charge neutralization by gas ions near the gas-solid interface. This paper provides a novel technique for realizing rapid surface charge dissipation on the insulator, which is of great significance for a variety of engineering applications of DC GIS/GIL. [ABSTRACT FROM AUTHOR]

This paper investigates the Multilevel Current Source Converter (MCSC) STATCOM. It proposes a new method of modulation. The new modulation method produces less THD and di/dt at the terminals of the MCSC STATCOM when compared to the widely used Phase-Shifted Carrier SPWM (PSC-SPWM). To ensure the inductors' currents remain balanced, a Current Balancing Algorithm (CBA) is presented. The CBA does not require any controls. It relies on assigning optimum switching states to each CSC module in real-time. In addition, two control strategies are presented in this paper. The first one assumes the STATCOM to be a SISO. Therefore, it only requires one PI controller. However, the gains for the controller must be changed if the STATCOM was to transition from capacitive mode to inductive mode, or vice versa. The second control strategy overcomes this problem by implementing a TITO integral state feedback controller. The contributions of this paper are validated via simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes an adaptive model of modular multilevel converter (MMC) for electromagnetic transient (EMT) simulations. The model is applicable to MMCs with arbitrary numbers of half-bridge and full-bridge submodules. The proposed design includes average value model, arm equivalent model, and detailed equivalent model. It allows smoothly transitioning from one model to another during time-domain simulations depending on the desired accuracy and execution time constraints. Modifications required in conventional MMC models to achieve smooth transitions are presented in the paper. Time-domain initialization methods are developed for each constituting model, including initialization of the appropriate control system blocks. Validity and effectiveness of the proposed adaptive model is demonstrated using EMT simulations of 401-level MMC-HVDC system. [ABSTRACT FROM AUTHOR]

This paper includes some results of switched Boolean control networks. The switched signals considered in this paper is time variant and it follows a certain probabilistic distribution vector. Given a concept of stabilization with stochastic switched signals, we obtained a necessary and sufficient condition for stabilization. Then a state feedback control depending on switched signals is designed to stabilize the system considered. Later we investigate a case when the switched signal $\theta (t)$ is unknown at time $t$ , and what we have is the prediction switched signal $\hat {\theta }(t)$. For a given prediction matrix, a necessary and sufficient condition is given to preserve the stabilization. Except state feedback control, asynchronous pinning control for switched Boolean networks (BNs) is also considered. A necessary and sufficient condition is extended for the stability of BNs with stochastic switched signals. Moreover, algorithms are presented to find the minimal number of pinned nodes based on controlling minimal number of subsystems. Examples are shown to illustrate the effectiveness of the obtained results. [ABSTRACT FROM AUTHOR]