Search

The DC distribution network is a low-inertia system, which is very sensitive to load disturbance, system failure, and other factors. By adding virtual capacitance to the converter connected to the power supply, the virtual inertia of the DC power grid can be improved. Firstly, this paper proposes a strategy for adjusting virtual capacitance based on the voltage change rate to achieve adaptive control of virtual inertia, which enables the converter to quickly absorb or release energy during power fluctuations. Secondly, the adaptivity of the strategy is improved and the main control parameters in the proposed control method are qualitatively analyzed. Finally, the four-terminal photovoltaic storage DC distribution network system is constructed. Through Simulink, the adaptive virtual inertia control is incorporated on the battery side to simulate and validate the effectiveness of the strategy and the rationality of parameter analysis. The results show that this method can provide flexible and adjustable inertia support for DC grids and improve the voltage stability of DC grids. [ABSTRACT FROM AUTHOR]

This study thoroughly compares multiple single bidirectional and multiport converters (MPCs), highlighting the significant role of MPCs in multi-input and multi-output (MIMO) systems. MPCs offer a more efficient and cost-effective solution than multiple single converters, especially in applications involving photovoltaic (PV), electric vehicles (EVs) with storage systems, and power grids. This research emphasizes the importance of multi-input converters (MICs) in integrating diverse voltage sources. It notes the rising popularity of multi-output DC-DC converters in portable electronics, owing to their reduced component count, lower costs, and compact design. This paper emphasizes comparisons based on diverse aspects and applications, shedding light on recent developments in basic bidirectional converters. Additionally, it delves into the advancements in MPC topologies, focusing on efficiency, reliability, and modularity improvements. These advancements are crucial for harnessing cost reduction, simplicity, and compactness. Furthermore, this paper introduces an innovative multiport DC-DC converter tailored for integrating and managing renewable sources. This new converter design enhances PV system and battery storage performance by reducing power conversion steps, using fewer components, and improving voltage-boosting capabilities. Its unique bidirectional buck-boost structure allows for versatile connections between sources and loads with varying voltage and power requirements. The performance of this novel converter is evaluated through MATLAB/Simulink simulations under different scenarios. Experimental studies further validate its effectiveness, marking a significant contribution to power conversion and management in integrating renewable sources such as DC microgrids. [ABSTRACT FROM AUTHOR]

In this paper, a hybrid control method with adaptive phase-shifting modulation (PSM) and pulse-frequency modulation (PFM) is proposed to optimize the steady-state performance of an LLC resonant converter in wide voltage-gain range application. For the primary-side switches under the hybrid control method, zero-voltage switching (ZVS) performance is maintained over wide voltage-gain range and the turn-off loss is reduced; therefore, the converter reconciles wide voltage-gain range and high efficiency. Mode characteristics under different phase-shifting-angle-θ and switching-frequency-fs combinations is analyzed, and then the soft-switching characteristic is revealed. By introducing time domain analysis, the turn-on current of the primary-side switches is calculated, and thus the ZVS boundary of different θ and fs combinations is inferred. In addition, to acquire the optimum steady-state operation of the converter, the turn-off current is calculated; by making the converter work near to the minimum turn-off current operating point, the turn-off loss can be reduced greatly. With the principles of achieving ZVS performance and minimizing turn-off current, the phase-shifting angle θ of PSM is designed to be adaptive to the reference output voltage, no additional circuits are needed, and the two control degrees (θ and fs) are simplified to one (fs). The simulation and experiment are developed to verify the feasibility and effectiveness of the hybrid control method; the results show that ZVS performance is maintained at wide voltage-gain range and the turn-off current of the hybrid control method is reduced to that of the single PFM, and thus the turn-off loss is reduced. The efficiency comparison validates the fact that the hybrid control method has less power loss than single PSM and single PFM. [ABSTRACT FROM AUTHOR]

Using modularized power converters with scalable energy storage in particle accelerators can be further enhanced with controls that can be adapted to optimise different design targets, such as to minimise the front‐end stage peak current, the depth of discharge of electrolytic capacitors or the thermal cycling of semiconductors. This paper proposes a control system that is able to individually adjust the power flow of the converter modules under pre‐defined load profiles, and hence separates the use of energy storage and grid connection even under rapid cycling. The paper briefly summarises the characteristics of the modular converter and proposes four energy control strategies that have been validated by simulation as well as experimentally on a 800 kW full scale prototype. It is shown that by applying each strategy, the corresponding design objectives can be achieved, for example, optimal utilisation of the energy storage systems or minimised current stress in the semiconductors. [ABSTRACT FROM AUTHOR]

Power converters can convert the electrical energy output by power source into specific forms required by target device. They are widely used in various fields such as electrification, transportation, and power systems, and are the core components of the systems. Power converters are composed of power semiconductor devices (such as IGBTs), which are prone to failure due to abnormal conditions and aging degradation, leading to power converter faults. Therefore, over the past twenty years, extensive fault diagnosis methods for power converters have been studied and proposed. Among them, symmetry-based methods have the characteristics of rapid diagnosis speed and strong robustness, but so far there's no systemic summary of such methods. Therefore, this paper reviews the relevant research on fault diagnosis of power converters based on symmetry in recent years, analyzes the mathematical principles of these methods, and compares their diagnostic performance. In addition, two factors that may have an influence on the symmetry are pointed out. This paper provides references and suggestions for the future development and research of power converter fault diagnosis. [ABSTRACT FROM AUTHOR]

Most coupled inductor‐based step‐up DC–DC converters encounter a significant voltage overshoot on their power switch due to the leakage inductance of the coupled inductor. So, they need additional bulky snubber circuits or a sophisticated procedure for coupled inductor design to reduce that effect. This paper proposes an improved coupled inductor‐based DC–DC converter, which provides a high quadratic voltage conversion ratio without excessive voltage stresses on the power switch. An active clamp circuit that operates with the zero‐voltage switching (ZVS) feature has been utilized for this aim. This feature allows the main power switch to be selected from low voltage ratings and low on‐resistance MOSFETs, which reduces conduction loss. The topology also benefits from continuous input current, high gain, high efficiency, and an appropriate number of components compared with the produced gain. In this article, the theory and operation of this converter are described by proposing the dc and small‐signal models, loss model, and continuous and discontinuous current modes (CCM and DCM) relations. Experimental results are represented to evaluate the performance of the proposed topology. For this purpose, a 240 V/240 W prototype has been designed and fabricated. Results confirm the above claims. [ABSTRACT FROM AUTHOR]

Power grids are progressing, and the possibility of incorporating DC grids toward hybrid AC/DC grids is gaining increasing relevance, as several technologies available nowadays are operating natively in DC. This paper proposes a topology of a full-controlled bidirectional dual-stage interleaved converter for interfacing hybrid AC/DC grids. The topology is based on a dual-stage architecture, constituted by an AC/DC converter and by a DC/DC converter, both based on interleaved power converters. On the AC side, which is connected to the main AC power grid, the proposed dual-stage architecture operates with sinusoidal current in phase or phase opposition with the voltage, meaning a bidirectional operation. In addition, it has the possibility of interfacing with other AC loads, such as domestic electrical appliances, or with an AC microgrid. The DC link, formed by the AC/DC power stage, is interfaced with a DC power grid, which provides numerous advantages, e.g., for interfacing battery electric vehicles directly charged in DC, as well as other DC loads, such as renewable energy sources. The DC/DC power stage is considered for interfacing with an energy storage system, which is capable of bidirectional power exchange with the DC grid or with the AC grid through the AC/DC power stage. A complete laboratory prototype was designed and developed, with the unified control algorithms implemented on a digital signal processor. The experimental results validated the operation of the full-controlled bidirectional dual-stage interleaved converter based on the specifications for the hybrid AC/DC grid, such as bidirectional operation, synchronization with the AC power grid, predictive current control, interleaved operation on both AC/DC and DC/DC power stages, DC-link voltage control for the DC grid, as well as the operation with different power levels. [ABSTRACT FROM AUTHOR]

In this paper, an interleaved DC–DC step-up converter with improved characteristics based on a voltage multiplier rectifier is presented. The proposed converter is presented and analyzed for two different operating duty regions including operating region 1 (0 < D ≤ 0.5), and operating region 2 (0.5 ≤ D < 1). This converter can be used in various applications such as energy storage, electric vehicles, and renewable energy systems. This converter is composed of two stages: an interleaved boost stage and a voltage multiplier rectifier stage, which collectively forms its general structure. The interleaved boost stage is a type of two-phase boost converter that transforms the input DC voltage into a high-frequency AC square waveform. This waveform can be readily filtered using smaller capacitors. The square-shaped voltage waveform from the interleaved boost stage is rectified and converted to a high DC voltage by the Voltage Multiplier Rectifier (VMR) stage. The operating regions, the evaluation of the steady-state condition, the voltage gain of the proposed converter's parasitic and ideal models as well as its losses and efficiency analysis have been evaluated. The proposed converter has an efficiency of 97% at the output power of 150 W. The proposed converter is simulated to convert a voltage of 25–159.5 V and to validate the mathematical relationships and simulation results, a laboratory prototype has been developed. The simulation and experimental results show the precision of the performance of the proposed interleaved boost converter. [ABSTRACT FROM AUTHOR]

This paper recommends new design for non-isolated semi-quadratic buck/boost converter with two similar structure that includes the following features: (a) the continuous input current has made it reasonable for PV solar applications and reduced the value of the capacitors in the input filter reducing the input ripple as well as EMI problems; (b) the topology is simple, and consists of a few numbers of components; (c) the semiconductor-based components have lower current/voltage stresses in comparison with the recently recommended designs; (d) semi-quadratic voltage gain is D (2 − D) / (1 − D)2; (e) 94.6 percent from the theoretical relations and 91.8 percent from the experimental for the output power of 72W, the duty of 54.2 percent, and output voltage of 72 V are the efficiency values in boost mode; (f) 89.3 percent from the theoretical relations and 87.2 percent from the experimental for the output power of 15W, the duty of 25.8 percent, and output voltage of 15 V are the efficiency values in buck mode. One structure is the continuous output current and negative output polarity, and other structure is positive output polarity. The recommended topologies have been studied in both ideal and non-ideal modes. The continuous current mode (CCM) is the suggested mode for the proposed converters. Moreover, the requirements of CCM have been discussed. The various kinds of comparisons have been held for voltage gain, efficiency, and structural details, and the advantages of the suggested design have been presented. A small-signal analysis has been completed, and the suitable compensator has been planned. Finally, PLECS simulation results have been associated with the design considerations. [ABSTRACT FROM AUTHOR]

As research into data centers progresses, the importance of resonant switched-capacitor converters in power supply design becomes more evident. Practical applications reveal that the values of resonant capacitors and inductors may deviate from their nominal values due to various factors, leading to resonant frequency instability. This instability poses a challenge to power electronics technology, affecting system reliability and performance. This paper analyzes the effect of frequency deviation on system functionality, identifies the relationship between output voltage and switching frequency, and proposes a self-tracking frequency strategy to address this issue. Through experimental validation, this approach shows that it maintains synchronization between switching and resonant frequencies, reducing losses associated with frequency misalignment. Simulation and experimental results validate the converter's stable operation and its ability to achieve zero-voltage and zero-current switching. [ABSTRACT FROM AUTHOR]

The LLC resonant converter, which is extensively utilized across various industrial fields, significantly depends on its parameters for performance optimization. This paper establishes a time-domain analytical model for the LLC resonant converter under Pulse Frequency Modulation (PFM) and proposes a multi-objective parameter optimization design method with stepwise constraints. The proposed method limits the resonant capacitor voltage while ensuring that the converter meets the voltage gain requirement and realizes Zero-Voltage Switching (ZVS). The converter's performance is then optimized with the objective of minimizing the switching frequency range, the resonant inductor current, and the RMS value of the switching current on the secondary side. Compared with the existing methods, the proposed method has the advantages of comprehensive consideration and wide application scenarios. Finally, a 1200 W experimental prototype was fabricated, with experimental results verifying the feasibility of the proposed optimization design method and demonstrating that the prototype's maximum efficiency reaches 96.54%. [ABSTRACT FROM AUTHOR]

The utilization of switched inductors, involving parallel charging and series discharging of inductors, is extensively embraced in diverse DC–DC converters for attaining high voltage gain; nevertheless, the stress on switch voltage and diode current escalates considerably with an increased count of inductors integrated into the switched inductors network. In the classical multistage switched inductor converter, the switch voltage aligns with the output voltage, and the diode experiences a high current as the number of stages increases. This research recommends a DC–DC multistage converter for energy conversion and high voltage gain with low stress. In this paper, a novel multistage switched inductor converter is introduced and designed to attain higher voltage gain while mitigating the stresses on switch voltage and diode current. The proposed circuit is created by replacing the standard multistage switched inductor converter's possible diodes with power switches. All of the switching devices are connected in such a way that the output voltage and input current are shared by all of the switches and diodes, respectively. As a consequence, the voltage stress on switches and the current stress on diodes are comparatively low, resulting in a high efficiency compared to a typical multistage switched inductor converter. It's interesting to note that the proposed converter and a typical multistage switched inductor converter both require the same amount of components. Different operation modes, analysis, a non‐ideal model, and a comparison of the suggested and recently constructed converters are discussed. The effectiveness and performance of the circuit are validated experimentally. [ABSTRACT FROM AUTHOR]

This paper deals with the control and performance improvement of parallel-operated voltage-source inverters (VSIs) controlled as virtual synchronous generators (VSGs). In publications regarding the parallel-operated VSGs, transmission lines are considered to be mainly inductive. However, less analytical works have been done regarding the control of paralleled VSGs in low-voltage grids with dominant resistive impedances. Once VSIs are controlled as VSGs in a microgrid with more resistive transmission lines, swing equation and system representation for the power-angle synchronization will change leading to a new control structure. Therefore, this paper deals with the control of parallel-operated converter-based VSGs in low-voltage grids with dominant resistive line impedances. In this way, the VSG representation, comprising the swing equation and V-P droop characteristic, for applications in highly resistive microgrids is presented, in which the swing equation and VSG frequency are related to reactive power. Then, the V-P droop characteristic is modified and an enhanced P-V droop characteristic for proper sharing of active power between the VSGs in highly resistive microgrids is proposed. Next, the VSG control is modified so that the R/X ratio at the VSG output increases and thus the decoupled control of active/reactive powers in relatively inductive cases is realized as well. [ABSTRACT FROM AUTHOR]

The voltage source converter-based multi-terminal DC transmission (VSC-MTDC) system can use additional frequency control to respond to the frequency change of faulty AC system. However, the control coefficient of traditional additional frequency control is mostly fixed, and the control flexibility is insufficient, so it cannot be adjusted adaptively according to the frequency change of the system. Therefore, a frequency control strategy of the VSC-MTDC system based on fuzzy logic control is proposed. Based on the DC voltage slope controller, this strategy introduces an additional frequency controller based on fuzzy logic control, takes the frequency deviation and frequency change rate as the additional controller input, and dynamically adjusts the control quantity through the fuzzy logic control link to realize the adaptive adjustment of the VSC-MTDC system to the AC system's frequency. Finally, a three-terminal flexible HVDC system is built on the PSCAD/EMTDC simulation platform for simulation verification. The results show that the proposed control strategy can effectively use the flexible DC system to support the frequency of the AC system and significantly improve the frequency stability of the faulty AC system. [ABSTRACT FROM AUTHOR]

This paper proposes an interleaved coupled‐inductor high step‐up direct current (DC)–DC converter. This converter uses a coupled inductor (CI), a voltage multiplier (VM) integrated with a regenerative passive lossless clamp circuit to enhance the voltage conversion ratio. The interleaved structure is used as the front stage of the proposed converter to reduce the input current ripple. The proposed converter has benefits such as low voltage stress across semiconductor elements, high voltage gains, and continuous input current, which makes it suitable for applications such as renewable energy sources. In addition, to reduce the negative effects of leakage inductance and recover the energy stored in it, a diode‐capacitor clamp circuit is used. Moreover, a comprehensive analysis has been done on the details of the performance of the proposed converter in different operation modes. Also, its design, the voltage and current equations of all the elements, and efficiency analysis are obtained. In addition, a comprehensive comparison has been made with some similar converters. The experimental results of a prototype with 260 W 96.9% is presented to validate the performance of the proposed converter. [ABSTRACT FROM AUTHOR]

In some applications of microgrids and distributed generation, it is necessary to feed islanded or stand-alone loads with high-quality voltage to provide low total harmonic distortion (THD). To fulfil these demands, an L C filter is usuallyconnected to the output terminals of power electronics converters. A cascaded voltage and current control loop with pulse-width modulation schemes are used to regulate the voltages and currents in these systems. However, these strategies have some drawbacks, particularly when multiple-input–multiple-output plants (MIMO) are controlled using single-input–single-output (SISO) design methods. This methodology usually produces a sluggish transient response and cross–coupling between different control loops and state variables. In this paper, a model predictive control (MPC) strategy based on the concept of optimal switching sequences (OSS) is designed to control voltage and current in an L C filter connected to a three-level neutral-point clamped converter. The strategy solves an optimisation problem to achieve control of the L C filter variables, i.e., currents and output voltages. Hardware-in-the-loop (HIL) results are obtained to validate the feasibility of the proposed strategy, using a PLECS–RT HIL platform and a dSPACE Microlab Box controller. In addition to the good dynamic performance of the proposed OSS–MPC, it is demonstrated using HIL results that the control algorithm is capable of obtaining low total harmonic distortion (THD) in the output voltage for different operating conditions. [ABSTRACT FROM AUTHOR]

The DC/DC converters are commonly used in DC microgrids to achieve the desired performance of a system under different operating conditions. The dynamics of an isolated DC microgrid with solar photovoltaic panels, battery, and constant power load is a fractional nonlinear model; thus, the complex nonlinear method should be applied for controller design and stabilizing the system. In multi-input multi-output systems with non-linear elements, non-linear control methods should be used, but this paper presents a straightforward technique for designing decentralized controllers for the buck, boost, and buck-boost converters in an isolated DC microgrid to stabilize the system and implement Maximum Power Point Tracking (MPPT) control of the solar photovoltaic panels. The presented methods consider the nonlinear decentralized feedback linearizing control for the nonlinear system. Depending on the performance of the converters in the system, proper dynamic models are introduced for the converters, and decentralized controllers are determined. Various scenarios are simulated and compared to conventional methods. The results indicate that the settling time of the output variables and the overvoltage of the DC-link voltage are reduced by less than 30% compared to other techniques. [ABSTRACT FROM AUTHOR]

This paper presents the design and application of a boost converter operated in continuous conduction mode for 15 W, with a 25 kHz switching frequency using an inductor-capacitor-inductor (LCL), pi, inductor capacitor (LC) with damping, and LC electromagnetic interference filters. Also, modeling and analysis of the boost converter in terms of state space and small signal are given. Furthermore, the effect of each filter on differential mode (DM) noise and control characteristics is presented using root locus and bode diagrams, which are not detailed in the literature for the boost converter. All results obtained from applications and simulations are compared. Moreover, frequency spectrums are given to compare DM noises. As a result, from a control point of view, the LCL filter provides better results, and for reducing DM noise, the LC and pi filters are superior to others. Besides, the LCL filter reduces the inductor value by 30% compared to other filters. [ABSTRACT FROM AUTHOR]

This paper describes a groundbreaking design of a three-phase interleaved boost converter for PV systems, leveraging parallel-connected conventional boost converters to reduce input current and output voltage ripple while improving the dynamic performance. A distinctive feature of this study is the direct connection of a Li-Ion battery to the DC link, which eliminates the need for an additional charging circuit, which is a departure from conventional approaches. Furthermore, the combination of an MPPT controller and a closed-loop fuzzy controller with a current control mode ensures accurate switching signal generation for all three phases. The meticulously tuned system exhibits a remarkably low ripple content in the output voltage, surpassing calculated values, and demonstrates a superior dynamic performance. The investigation extends to a comprehensive analysis of losses, encompassing inductor copper loss and semiconductor conduction loss. In all scenarios, the converter exhibits an efficiency exceeding 93%, highlighting its robust performance as an effective solution for PV systems. [ABSTRACT FROM AUTHOR]

Power electronics converters have been widely deployed in modern power systems in different voltage levels. The complex operation characteristics of power converters, which combine different control modes and various current saturation states, are also significantly changing the power systems' behavior in fault conditions. The objective of this paper is to develop a steady-state short-circuit calculation solver for power systems with power electronics without the need of detailed dynamic models. In particular, the steady-state operation equations related to the converter control are included in the system formulation. An extended Newton–Raphson (NR) solver is proposed to compute the short-circuit equilibrium point that considers converters' operation limits. Also, an iterative algorithm is presented in order to efficiently identify the current saturation states of power converters under a specific short-circuit fault scenario. Case studies have been presented with several power systems with voltage source converters (VSCs). Dynamic simulations are included to validate the accuracy of the proposed methodology. • This paper presents an extended Newton–Raphson solver to cope with the new formulation considering power converters' operation. • An iterative algorithm that identifies the current saturation state of a converter in a specific fault scenario. • The proposed methodology has been implemented in several benchmark systems with VSCs. simulation results. [ABSTRACT FROM AUTHOR]

In this paper, the hybrid synchronization based grid forming (HS-GFM) control and coordination strategy are proposed for the inverter and boost converter to provide frequency support. As the main contribution, the inertia power and damping power are designed with HS-GFM based coordination strategy between inverter and boost converter. The inertia power can be obtained from DC capacitor and photovoltaic system in deloading mode independently. Besides, the damping power can be realized from the PV inverter in deloading mode. After that, the small signal models of inverter and boost converter considering grid frequency coupling are constructed with simplified single input single output (SISO) model to guide the parameter selection. Further, the grid synchronization stability, synchronization bandwidth and grid strength influence on the frequency response of the PV inverter can be analyzed with SISO model. Compared with conventional DC voltage based GFM, HS-GFM can improve stability especially in strong grid with slight reduction of synchronization bandwidth while it has the risk of instability in weak grid if parameters are not proper. Compared with phase locked loop (PLL) based control, the proposed HS-GFM control achieves a fast response under frequency excursion with better stability in weak grid. Finally, realtime and offline simulations are carried out to verify the proposed strategy and analysis. • Inertia and damping power are designed with hybrid synchronization based GFM control. • The DC side thevenin equivalence of boost converter is obtained for SISO analysis. • SISO model of PV inverter is built for stability analysis and parameter selection. • Comparisons with conventional GFM and phase locked loop based control are presented. [ABSTRACT FROM AUTHOR]

Power conversion systems for wireless power transfer (WPT) applications have demanding requirements for continuity of service, besides being operated with stressing environmental conditions. Diagnostic and prognostic programs are thus quite useful and this work shows a novel approach based on the analysis of spectra of an autoregressive (AR) model to recognize a wide range of faulty devices, including incipient faults, when deviations from nominal parameters begin to manifest. AR modeling provides cleaner and easier to interpret spectra, where only the salient features remain, and they are more sensitive to variations in the corresponding time domain waveforms. A log spectral distance is calculated that successfully separates healthy and faulty states of the feeding single-phase inverter, even in challenging scenarios of poor signal-to-noise ratio. [ABSTRACT FROM AUTHOR]

A general overview of Noise-Shaping Successive Approximation Register (SAR) analog-to-digital converters is provided, encompassing the fundamentals, operational principles, and key architectures of Noise-Shaping SAR (NS SAR). Key challenges, including inherent errors in processing circuits, are examined, along with current advancements in architecture design. Various issues, such as loop filter optimization, implementation methods, and DAC network element mismatches, are explored, along with considerations for voltage converter performance. The design of dynamic comparators is examined, highlighting their critical role in the SAR ADC architecture. Various architectures of dynamic comparators are extensively explored, including optimization techniques, performance considerations, and emerging trends. Finally, emerging trends and future challenges in the field are discussed. [ABSTRACT FROM AUTHOR]

• ZnS shells remarkably increase the stability and efficiency of Yb3+-doped PeQDs. • ZnS enables perovskite host to Yb3+ energy transfer efficiencies as high as 81.3 %. • ZnS-coated PeQDs still light up when immersed in water for 70 h. • PeQDs@ZnS led to a 13.5 % relative increase in the photovoltaic efficiency of SSCs. • The T 80 of capped PeQDs@ZnS-SSCs under 25 °C and 50 % RH was 11,224 h. Yb3+ doped lead halide perovskite quantum dots (PeQDs) with efficient quantum cutting emission are thought to be the most promising photon energy converter for improving the performance of silicon-based electronics. Nevertheless, the low external quantum efficiency (EQE) and instability make it unfeasible for industrial use. Here, we present a unique PeQDs@ ZnS core–shell device that achieves outstanding stability and up to 39 % EQE by effectively controlling energy transfer from the PeQDs to the Yb3+ through ZnS coating. These advances are attributed to the large UV absorption and the strong localized effect of the ZnS shells on the conduction band electrons of the PeQDs. Density functional theory (DFT) first-principles simulations indicate that ZnS coating can facilitate the energy transfer of PeQDs to Yb3+. Power conversion efficiency (PCE) of silicon solar cells was significantly enhanced by ZnS-coated Yb3+ doped PeQDs, yielding a noteworthy 13.5 % relative PCE improvement over 30 measurement sets. Significantly, the stability of SSCs with ZnS-coated PeQDs films is considerably improved, resulting in a capped device T 80 lifespan of up to 11,224 h. Moreover, ZnS-coated PeQDs films can significantly boost the EQE of silicon photodiodes (Si-PDs) and extend their response to deep ultraviolet light. This paper presents an efficient and consistently stable photon energy converter with great commercialization potential. [ABSTRACT FROM AUTHOR]