Search

With the rapid development of global energy transformation and new power system, ensuring the stability of distributed energy grid connections is the key to maintaining the reliable operation of the whole power system. This paper constructs detailed impedance models of grid-following (GFL) and grid-forming (GFM) inverters using a harmonic linearization method and thoroughly investigates the mechanisms of resonance when inverters are connected to the grid, as well as the impact of model parameters on the stability of the grid system. This paper also briefly analyzes the scenario where distributed energy and electric vehicles are integrated into the grid simultaneously, demonstrating that grid system stability can be ensured in complex grid situations through reasonable parameter design. Lastly, the accuracy of the proposed impedance models and analysis is verified through MATLAB/Simulink simulations. [ABSTRACT FROM AUTHOR]

The main contribution of this paper is to present a simple algorithm that theoretically and numerically assesses the switching angles of an inverter operated with the SPWM technique. This technique is the most widely used for eliminating harmonics in DC-AC converters for powering motors, renewable energy applications, household appliances, etc. Unlike conventional implementations of the SPWM technique based on the analog or digital comparison of a sinusoidal signal with a triangular signal, this paper mathematically performs this comparison. It proposes a simple solution to solve the transcendental equations arising from the mathematical analysis numerically. The technique is validated by calculating the total harmonic distortion (THD) of the generated signal theoretically and numerically, and the results indicate that the calculated angles produce the same distribution of harmonics calculated analytically and numerically. The algorithm is limited to single-phase inverters with unipolar SPWM. [ABSTRACT FROM AUTHOR]

The application of electrochemical cells as a source unit of electrical energy is rapidly growing—used in electric vehicles and other electric mobility devices, as well as in energy supply systems—as energy storage, often together with renewable energy sources. The key element of such systems is the power electronic converter used for DC energy storage and AC grid interfacing. It should be bidirectional to charge and discharge the battery when it is necessary. Two-stage battery interface converters are the most common; their DC-DC stage controls the battery current and adjusts voltage, but the DC-AC stage (inverter or frontend) controls the current in the grid. The use of unfolding inverters in two-stage battery interfaces can have some advantages. In this case, the DC-DC converter produces half-sinewave pulsating voltages and currents, but the unfolding circuit changes the polarity of the voltages and currents and produces no switching losses. Another trend of modern power electronics is the principle of partial power processing. In this case, power electronic converters deal only with a part of the total power; therefore, losses in such converters are reduced. This paper considers combining unfolding frontends with partial power DC-DC converters that enable the further reduction in losses. In this paper, it is shown that such implementation of the partial power conversion principle in semi-DC-AC systems is really possible based on the real-time matching of the voltage of the partial-power DC-DC converter, battery voltage (which depends on its state of charge) and the rectified instantaneous voltage of the AC grid. [ABSTRACT FROM AUTHOR]

This paper presents a single-phase Full-Bridge (FB) inverter with a hybrid commutation technique designed to reduce the harmonic distortion caused by the loss of the controller capability around the zero-crossing point in the unipolar commutation region. The hybrid modulation changes from unipolar to bipolar commutation under the loss of the reference control, improving the robustness and efficiency of the method. The commutation technique improves the switching performance and reduces the switching losses. Simulation models are developed in MATLAB/Simulink R2023b to evaluate their performance under different operating conditions. The results show that the proposed commutation technique can achieve high efficiency, low total harmonic distortion (THD), and fast dynamic response. The experimental implementation of sliding mode control (SMC) implemented in an STM32 microcontroller confirms that the hybrid commutation technique can reduce the THD by 0.96 percentage points for local (off-grid) loads and up to 2.45 in an industrial grid-tie network, compared with unipolar commutation. These findings highlight the potential of the proposed modulation technique for applications like solar panels and offer crucial insights for ongoing research and development in this field. [ABSTRACT FROM AUTHOR]

Copyright of Przeglad Elektrotechniczny is the property of Przeglad Elektrotechniczny and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

As the penetration of distributed generation (DG) systems in the grid is increasing, the challenge of combining large numbers of DGs in the power systems has to be carefully clarified and managed. The control strategy and management concept of the interconnected systems should be flexible and reliable to handle the various types of DGs. This can be suitably met by microgrids. This paper introduces the microgrid structure and elements and states the main objectives that should be achieved by the microgrid controllers and each DG controller in both operation modes (grid‐connected and island mode). It also presents the challenges of having multiple DG units in a microgrid in terms of accurate power control/sharing, voltage and frequency regulation, power management between DGs, different renewable energy sources integration and deployment, seamless mode transfer, and the modeling issues. The centralized and decentralized control techniques as potential solutions have been discussed and compared by highlighting the advantages and disadvantages of each. Furthermore, the recent control techniques for drooped alternating current microgrids and the main proposed solutions and contributions in the literature have been exposed to finally overcome the droop control limitations and obtain a flexible and smart distributed power system. [ABSTRACT FROM AUTHOR]

Summary Multilevel inverters are known as essential converters in renewable sources. First, in this paper, a new submodule is presented, and based on it, a new sub‐multilevel inverter is presented. The proposed sub‐multilevel inverter consists of several unidirectional and bidirectional switches and DC voltage sources. Then, the generalized topology, developed in two modular and cascaded modes, is presented to increase production levels. The proposed submodules are connected in series in the modular topology, increasing production levels. The proposed topology to produce the maximum output levels has the minimum number of IGBTs, drivers, DC voltage sources, etc. Mathematical analyses for conduction and switching losses are provided, and mathematical analyses for the number of devices and voltage across the switches are also presented. In addition to the mathematical analysis of losses, the simulation results are also presented. A general comparison of proposed topology components is presented to demonstrate their advantages. This comparison shows that the proposed topology has the minimum number of power electronic devices. In this paper, nearest level modulation is used to control the proposed topology. The simulation and experimental results of the proposed sub‐multilevel verify the performance of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper conducts a comprehensive analysis of offshore wind-photovoltaic hybrid systems, presenting autonomous components tailored for maritime applications. Focusing on the critical role of these systems in supplying electricity to regions with limited infrastructure, particularly maritime zones, the study explores economic advantages over traditional power line installations, emphasizing remote areas. Key components, including battery storage, autonomy, battery selection (with a spotlight on lead-acid batteries), charge controllers, inverters, and the integration of Automatic Identification System (A.I.S.) for maritime safety, are discussed. The article concludes by underscoring the significance of power supply buoys for ship safety and efficient refueling near hybrid systems. [ABSTRACT FROM AUTHOR]

Copyright of Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji is the property of Gazi University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper describes the effects of power device characteristics on the harmonics of the inverter output voltage and magnetic field leakage in a wireless power transfer system for electric vehicles with phase shift control and the suppression method of the haemonics. Even when the phase shift angle is theoretically set to minimize harmonics, the experimental results have confirmed the existence of the remaining harmonics, which have dead-time dependence. Harmonics with dead-time dependence include those caused by changes in the pulse width depending on the dead time, which have been conventionally compensated for by dead-time compensation. However, the targeted harmonics have a dead-time dependence even when the pulse widths are matched. Therefore, we focused on the difference between the dead-time period and other periods. Further, as the conduction resistance differs between these two periods, we performed a circuit analysis, also considering the conduction resistance. From the results, it was theoretically clarified that harmonics are generated because of the difference in resistance in the forward and reverse directions of power devices. Furthermore, the theoretically calculated dead time dependence of the device-induced harmonics was confirmed by experimental measurements of the harmonics of the inverter output voltage waveform and the magnetic field leakage. This confirms that one of the factors responsible for the harmonics is the difference in the device conduction resistance before and after the dead-time period. The main contributions of this paper are the revelation of unconventional dead-time-dependent harmonics and the proposal of a method for suppressing them.

A Rectangular core–shell (RCS), employed to three fins vertically stacked with gate oxide stack junctionless nanosheet, along with doping and gate/dielectric engineering, is explored. This paper proposes an N-type three fins vertically stacked with gate oxide stack junctionless nanosheet with opposite core doping in the channel referred to as RCS. The simulation results show that three fins vertically stacked with gate oxide stack with RCS junctionless nano-sheet exhibit reduced Ioff is 6.913E-21, increased Ion is 2.408E-07, Ion/Ioff ratio is 0.418×106, DIBL is 6.9mV and SS is 60.65 mV/dec, respectively. Furthermore, the P-type of three fins vertically stacked with gate oxide stack junctionless nanosheet and combined -type and P-type three fins vertically stacked with gate oxide stack junctionless nano-sheet were stimulated to construct the inverter circuit. The Voltage Transfer Characteristics (VTC) of three fins vertically stacked with gate oxide stack junctionless nano-sheet with RCS have HfO2 as the gate-oxide based inverter has been notably improved compared to SiO2, al2O3 as a gate oxide and conventional three fins vertically stacked with gate oxide stack junctionless nano-sheet inverter. [ABSTRACT FROM AUTHOR]

A quadratic converter is now a days being investigated for high boost topologies. This paper presents the quadratic converter-based single-phase grid-connected system. For this system, the DC side control loop is regulated using a symmetrical shoot-through (SST)-based PWM. AC side current controller is implemented by the variation of modulation index in a nearly decoupled manner. The advantage of the suggested system is in terms of several controls particularly for input variations and load changes which are most beneficial in the case of grid application. The experimental results are presented to support the simulation results. The simulation results are achieved using MATLAB/SIMULINK. [ABSTRACT FROM AUTHOR]

The main contribution of this paper is to present a simple algorithm that theoretically and numerically assesses the switching angles of an inverter operated with the SPWM technique. This technique is the most widely used for eliminating harmonics in DC-AC converters for powering motors, renewable energy applications, household appliances, etc. Unlike conventional implementations of the SPWM technique based on the analog or digital comparison of a sinusoidal signal with a triangular signal, this paper mathematically performs this comparison. It proposes a simple solution to solve the transcendental equations arising from the mathematical analysis numerically. The technique is validated by calculating the total harmonic distortion (THD) of the generated signal theoretically and numerically, and the results indicate that the calculated angles produce the same distribution of harmonics calculated analytically and numerically. The algorithm is limited to single-phase inverters with unipolar SPWM.

With the rapid development of global energy transformation and new power system, ensuring the stability of distributed energy grid connections is the key to maintaining the reliable operation of the whole power system. This paper constructs detailed impedance models of grid-following (GFL) and grid-forming (GFM) inverters using a harmonic linearization method and thoroughly investigates the mechanisms of resonance when inverters are connected to the grid, as well as the impact of model parameters on the stability of the grid system. This paper also briefly analyzes the scenario where distributed energy and electric vehicles are integrated into the grid simultaneously, demonstrating that grid system stability can be ensured in complex grid situations through reasonable parameter design. Lastly, the accuracy of the proposed impedance models and analysis is verified through MATLAB/Simulink simulations.

The application of electrochemical cells as a source unit of electrical energy is rapidly growing—used in electric vehicles and other electric mobility devices, as well as in energy supply systems—as energy storage, often together with renewable energy sources. The key element of such systems is the power electronic converter used for DC energy storage and AC grid interfacing. It should be bidirectional to charge and discharge the battery when it is necessary. Two-stage battery interface converters are the most common; their DC-DC stage controls the battery current and adjusts voltage, but the DC-AC stage (inverter or frontend) controls the current in the grid. The use of unfolding inverters in two-stage battery interfaces can have some advantages. In this case, the DC-DC converter produces half-sinewave pulsating voltages and currents, but the unfolding circuit changes the polarity of the voltages and currents and produces no switching losses. Another trend of modern power electronics is the principle of partial power processing. In this case, power electronic converters deal only with a part of the total power; therefore, losses in such converters are reduced. This paper considers combining unfolding frontends with partial power DC-DC converters that enable the further reduction in losses. In this paper, it is shown that such implementation of the partial power conversion principle in semi-DC-AC systems is really possible based on the real-time matching of the voltage of the partial-power DC-DC converter, battery voltage (which depends on its state of charge) and the rectified instantaneous voltage of the AC grid.

Purpose – Traditional level inverter technology has drawbacks in the aspect of Total harmonic distortion (THD) and switching losses for higher frequencies. Due to these drawbacks, two-level inverters have become unprofitable for high-power applications. Multilevel inverters (MLIs) are used to enhance the output waveform characteristics (i.e. low THD) and to offer various inverter topologies and switching methods. Design/methodology/approach – MLIs are upgraded versions of two-level inverters that offer more output levels in current and voltage waveforms while lowering the dv/dt and di/dt ratios. This paper aims to review and compare the different topologies of MLI used in high-power applications. Single and multisource MLI's working principal and switching states for each topology are demonstrated and compared. A Simulink model system integrated using detailed circuit simulations in developed in MATLAB®–Simulink program. In this system, a constant voltage source connected to MLI to feed asynchronous motor with squirrel cage rotor type is used to demonstrate the efficacy of the MLI under different varying speed and torque conditions. Findings – MLI has presented better control and good range of system parameters than two-level inverter. It is suggested that the MLIs like cascade-five-level and NPC-five-level have shown low current harmonics of around 0.43% and 1.87%, respectively, compared to two-level inverter showing 5.82%. Originality/value – This study is the first of its kind comparing the different topologies of single and multisource MLIs. This study suggests that the MLIs are more suitable for high-power applications.

Abstract As the penetration of distributed generation (DG) systems in the grid is increasing, the challenge of combining large numbers of DGs in the power systems has to be carefully clarified and managed. The control strategy and management concept of the interconnected systems should be flexible and reliable to handle the various types of DGs. This can be suitably met by microgrids. This paper introduces the microgrid structure and elements and states the main objectives that should be achieved by the microgrid controllers and each DG controller in both operation modes (grid‐connected and island mode). It also presents the challenges of having multiple DG units in a microgrid in terms of accurate power control/sharing, voltage and frequency regulation, power management between DGs, different renewable energy sources integration and deployment, seamless mode transfer, and the modeling issues. The centralized and decentralized control techniques as potential solutions have been discussed and compared by highlighting the advantages and disadvantages of each. Furthermore, the recent control techniques for drooped alternating current microgrids and the main proposed solutions and contributions in the literature have been exposed to finally overcome the droop control limitations and obtain a flexible and smart distributed power system.

An inexact 6-transistor full adder (FA) cell is presented. It is low-power and gives full-swing outputs because of the applied gate diffusion input (GDI) along with the dynamic threshold (DT) techniques. The FA which has three errors is used in a 10-transistor inexact 4:2 compressor based on the stacking circuit idea. The implementation by a 16-nm carbon nanotube field-effect transistor (CNTFET) technology shows a small area of 0.027 and $0.045~\mu \text{m}^{\mathrm{ 2}}$ for the FA and compressor, respectively. A new approximate sum of absolute differences (SADs) block is presented by the FA and compressor. The average power, power-delay-product (PDP), and peak signal-to-noise ratio (PSNR) of the SAD are 6.80 mW, 33.86 nJ, and 42.98 dB, respectively, which confirm its efficiency for bioimages difference detection. [ABSTRACT FROM AUTHOR]

This paper Techno-economic design of a standalone solar PV system with case study, TY Danjuma conference building, Rivers State University (RSU) Port-Harcourt provides alternative electric power services to the building. The area or building under consideration uses the off-grid power generation model having identified the inadequacy and irregular power supply which causes man-hour loss during the working period. There is enough solar energy to generate emission-free power. In literature, it has been seen that researchers are advocating for the utilization of these abundant natural resources to generate power. The long-run operational benefits cannot be neglected. To achieve the aim and objectives of this research, an analytical (components-wise) method was adopted. The various components required to provide green energy services were thoroughly and chronologically computed. The analysis provides specifications for the components as mentioned in the materials section and concerning the load demanded. Without a thorough load audit, the required solar PV and its delivery gadgetry would not be adequate. Hence, load survey, assumption and design calculations, etc., to achieve the 42kWp with 140 numbers of panels; 48 numbers of 200Ah, 12V deep cycle batteries, 25kVA inverter (or with two sets of inverters, 15kVA and 10kVA, 48Vdc/220Vac), 6 numbers of 150Amp, 48V solar charge controllers or a single 900Amp,48V solar charge controller was evaluated. The specification evaluated and presented was based on the load computed and the prevailing market for available components. From the techno-economic viewpoint of using solar-powered systems or diesel-powered generators, it was obvious that the solar-powered system has many more advantages in terms of daily, monthly or yearly running and maintenance costs as comparable to diesel-generator systems. Thus, it will be interesting to note that adequate utilization of renewable energy for electricity generation will be the best practice in the socioeconomic development of a state or a nation.

This paper presents a single-phase Full-Bridge (FB) inverter with a hybrid commutation technique designed to reduce the harmonic distortion caused by the loss of the controller capability around the zero-crossing point in the unipolar commutation region. The hybrid modulation changes from unipolar to bipolar commutation under the loss of the reference control, improving the robustness and efficiency of the method. The commutation technique improves the switching performance and reduces the switching losses. Simulation models are developed in MATLAB/Simulink R2023b to evaluate their performance under different operating conditions. The results show that the proposed commutation technique can achieve high efficiency, low total harmonic distortion (THD), and fast dynamic response. The experimental implementation of sliding mode control (SMC) implemented in an STM32 microcontroller confirms that the hybrid commutation technique can reduce the THD by 0.96 percentage points for local (off-grid) loads and up to 2.45 in an industrial grid-tie network, compared with unipolar commutation. These findings highlight the potential of the proposed modulation technique for applications like solar panels and offer crucial insights for ongoing research and development in this field.