Search

This paper focuses on an industrial application where renewable power produced by photovoltaic panels is exploited to feed a pneumatic transport plant. The proposed system requires the careful management of the energy flows involved since it includes the interaction with the electric grid and with an electrochemical storage (battery) rather than the correct choice of the photovoltaic panel and battery itself. A dedicated control system needs to be developed in order to accord together these energetic flows, also providing a degree of flexibility to implement different control logics. The methodology employed in the research is simulation, which through the construction of a model in Matlab Simulink is able to reproduce the behavior of the system components and their energetic interactions for a long time period. The aim of the research is to provide a tool for assessing the energetic convenience of different battery–PV panel combinations. Moreover, an economical assessment of the proposed system is provided and compared to the traditional setup. Simulation results show that the proposed system provides energy savings with respect to a traditional grid-powered plant. The economic assessment shows that the system becomes convenient over the traditional setup within a time frame compatible with an average PV panel's useful life. [ABSTRACT FROM AUTHOR]

In recent years, a Multilevel Inverter (MLI) topology is highly preferred in the various renewable energy applications for converting power due to their merits. In this paper, a three-phase inverter has been designed for grid-connected applications using Proportional Integral (PI) current controller scheme. To generate a sequence, the Level shift (LS) and Phase Shift (PS) Pulse Width Modulation (PWM) methodologies are adapted. This topology has been designed with two stages: the DC-DC conversion stage and DC-AC conversion stage. The DC-DC conversion stage is used to enrich input DC voltage which is obtained from the solar PV array. The PI current controller has been designed to regulate the grid current with park transformation. The performances of the inverter have been examined in terms of Total Harmonic Distortion (THD) using different PWM techniques and also investigated with existing research works. The developed results are verified using MATLAB/ Simulink. [ABSTRACT FROM AUTHOR]

The ever growing penetration of distributed generation (DG) in a distribution network has a profound impact on network protection and stability. Traditional protection schemes and algorithms need to be extensively investigated as more and more DGs get introduced into the network. The current version of IEEE Standard 1547 does not present a comprehensive solution for fault current detection in the presence of various kinds of DGs. Power electronic inverter-based DGs (IBDGs) are of special concern in distribution network protection as they are often incapable of providing sufficient fault current and their controllers play a principal role in the DG behavior. In this paper, the effects of voltage and current controllers for IBDGs on industrial and commercial power system protection schemes are investigated. It is shown that the inverter control mode has a direct impact on its fault current levels and duration. A simplified distribution network model with IBDG operating under voltage and current control modes was tested to verify the effects of these controllers. This paper also proposes an adaptive relaying algorithm to detect the faults in the presence of IBDGs with various types of controllers. [ABSTRACT FROM AUTHOR]

This paper proposes a family of hybrid converter topologies which can supply simultaneous dc and ac loads from a single dc input. These topologies are realized by replacing the controlled switch of single-switch boost converters with a voltage-source-inverter bridge network. The resulting hybrid converters require lesser number of switches to provide dc and ac outputs with an increased reliability, resulting from its inherent shoot-through protection in the inverter stage. Such multioutput converters with better power processing density and reliability can be well suited for systems with simultaneous dc and ac loads, e.g., nanogrids in residential applications. The proposed converter, studied in this paper, is called boost-derived hybrid converter (BDHC) as it is obtained from the conventional boost topology. The steady-state behavior of the BDHC has been studied in this paper, and it is compared with conventional designs. A suitable pulse width modulation (PWM) control strategy, based upon unipolar sine-PWM, is described. A DSP-based feedback controller is designed to regulate the dc as well as ac outputs. A 600-W laboratory prototype is used to validate the operation of the converter. The proposed converter is able to supply dc and ac loads at 100 V and 110 V (rms), respectively, from a 48-V dc input. The performance of the converter is demonstrated with inductive and nonlinear loads. The converter exhibits superior cross-regulation properties to dynamic load-change events. The proposed concept has been extended to quadratic boost converters to achieve higher gains. [ABSTRACT FROM PUBLISHER]

The safety and reliability of inverters play a significant role in stable power electronic system operations. Considering a railway vehicle air-conditioning inverter as a case study, this paper presents a generic open-circuit fault diagnosis method that can be applied to various inverter and control schemes. First, a detailed model of three-phase output currents under both normal and fault status is derived, and then the concept of space trajectory is introduced based on the three-phase output currents. The open-circuit faults of the inverter lead to output phase current distortion. Therefore, different types of faults have different space trajectories, and the corresponding shape of the space trajectory is considered to be a fault feature. Then, the fault is located by the direction vector and center-of-mass coordinate. The effectiveness and reliability of the diagnosis method are verified and analyzed using a hardware-in-the-loop test platform. [ABSTRACT FROM AUTHOR]

Voltage imbalances are one of the most severe challenges in electrical networks, which negatively affect their loads and other connected equipment. This paper proposes a voltage support control strategy to mitigate the voltage imbalance in inverter-based low voltage distribution networks. The control scheme is derived taking in mind the following control objectives: a) to increase the positive sequence voltage as much as possible, b) to decrease the negative sequence voltage as much as possible, c) to inject the power generated by the primary source, and d) to minimize the output current of the inverter. The innovative contribution of the proposed solution is based on the design of a control algorithm that meets the aforementioned objectives without resorting to communications with other grid components. The theoretical results are experimentally validated by selected tests on a laboratory setup with X/R ratio close to one. [ABSTRACT FROM AUTHOR]

A novel single-phase transformerless dual-mode interleaved multilevel inverter (DMIMI) is proposed in this paper, which can inject a highly sinusoidal ac current to the grid even with the input dc voltage less than the peak grid voltage. Furthermore, dead-beat controllers are developed to directly calculate the optimal duty cycles in a digital control platform. As compared to the traditional dual-mode multilevel approaches, the DMIMI offers high efficiency, less number of components conducting simultaneously in each operation mode, and the capability of reactive power exchange. This paper presents the theoretical analysis and the experimental results obtained from a 1-kW prototype. The experimental results reveal that the proposed DMIMI can achieve high conversion efficiency and low leakage current as well as high quality grid current. [ABSTRACT FROM AUTHOR]

The paper deals with the construction design, thermal simulation analysis and cooler control proposal of double three-phase inverter suitable for electric vehicles. It gives a discussion on basic mechanical design and electric topology, both having strong influence on electrothermal operability. The paper also presents the thermal analyses of the converter operated at specified loading profile and gives control possibilities. Finally, the paper presents the cooler control design and demonstrates its functionality. The paper also discusses its impact on the converter lifetime and implementation. [ABSTRACT FROM AUTHOR]

This paper proposes a new control scheme to eliminate the 3rd harmonic in the output currents of grid-following inverters under unbalanced grid conditions. Unbalanced grids adversely affect the performance of grid-following inverters due to the oscillations appearing on the DC-link voltage with a frequency twice the line frequency. The paper is based on instantaneous active reactive control (IARC) technique due to its advantages over other existing methods. However, the presence of severe asymmetrical 3rd harmonic distortions in the inverter output currents is the main challenge with IARC method, which impairs the power quality requirements. This paper enhances the IARC scheme by proposing a 3rd harmonic elimination approach by adopting a current reference generation method using the symmetric sequence components concept. Furthermore, the proposed scheme complies with the grid code requirements by injecting the requested reactive current. Finally, the proposed approach is evaluated by theoretical and simulation analysis and validated experimentally using a hardware setup. [ABSTRACT FROM AUTHOR]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

The ability of an electrical drive to continue operation without tripping in spite of short-duration voltage sags or power supply interruptions is known as power failure ride-through capability. Critical production processes in industries require the drives to smoothly ride-through during momentary power interruptions. The reliability of the drive is dependent on the maximum duration for which a total power supply failure can be tolerated without process interruption. This paper presents a method to extend the duration of the ride-through in voltage-source-inverter-fed vector-controlled induction motor drives with a front-end diode bridge rectifier. The proposed method minimizes the losses in the system during the ride-through, thereby enabling a longer ride-through duration. The method only requires a modification of the control software and hence is easy to implement. This paper also briefly describes two conventional methods used for ride-through and compares the proposed method with the conventional methods to clearly bring out its advantage. Simulation study using MATLAB/PLECS verifies the effectiveness of the proposed method. Hardware implementation of the method on a 30-kW induction machine indicates an extension of up to 34% in the ride-through duration with the proposed method, as compared with the conventional method. [ABSTRACT FROM AUTHOR]

This paper presents real-time diagnosis for open-circuited (O-C) and unbalance faults in power electronic converters (PECs) connected to residential small wind systems grid-tied. The spectrum analysis along with the dc components of the voltage and current measurements available in the converter is utilized for the O-C fault detection, classification and localization of the power switching devices in the PEC, as well as the identification of the unbalance input voltage to the converter. The proposed methodologies in this paper require much fewer inputs compared to the previous researches; therefore, they avoid any additional sensors or hardware which include further costs and expenses on such systems. The experimental evaluations for the proposed algorithms are provided and demonstrate the effectiveness and the robustness of the proposed diagnostic algorithms in this paper. The PEC under study consists of three main subsystems: uncontrolled three-phase rectifier, boost chopper, and single-phase inverter. [ABSTRACT FROM PUBLISHER]

This paper develops a simplified phasor model for predicting harmonics present at the point of common coupling between a voltage-source power converter and the utility network. It employs the frequency coupling matrix (FCM) modeling technique. The FCM is experimentally determined without requiring access to converter internal details, such as control and output filter parameters, which are generally not available for converters used in distributed generation systems. Experimental measurements are conducted on a commercially available two-stage, three phase, grid-tied photovoltaic inverter to assess the accuracy of experimentally determined FCMs to predict the harmonic behavior of grid-connected converters. This paper considers two grid conditions for the experimental analysis: 1) when the grid is stiff and contains only background voltage harmonics and 2) when the grid contains harmonic grid impedances as well as background voltage harmonics. In all cases, a close match between the results predicted by the FCM approach and experimental measurements is achieved, thus demonstrating the practical viability of using experimentally determined FCM models for harmonic predictions. [ABSTRACT FROM PUBLISHER]

This paper presents an improved dc-link voltage balancing algorithm for a three-level neutral-point-clamped inverter by considering phase current direction. Detailed studies on the effects of change in load current direction on the dc-link capacitor voltages are presented. A maximum value of power factor is numerically derived, above which it affects the capacitor voltage balancing capability. Compared with the previously presented research work, the inputs to the space-vector pulsewidth-modulation block are the three phase currents and the difference between the two capacitor voltages. Depending on the states of the two dc-link capacitor voltages and phase current direction, redundant voltage vector sequences are selected. The selected vectors keep the capacitor voltage deviations within 5% of the total dc-link voltage. Two zero switching vectors (i.e., PPP and NNN) are also removed from all subsectors of the earlier proposed strategy, which one used to produce higher common-mode voltages. Detailed simulation and experimental results are presented in this paper for a 6.0-kW surface permanent-magnet synchronous machine. Both the simulation and experimental results show the required performance of the proposed system. [ABSTRACT FROM AUTHOR]

Capacitor-current-feedback active damping has been widely used in LCL-type grid-connected inverters. However, the damping performance is deteriorated due to the negative equivalent resistance resulted by the digital control delays, and thus the grid-connected inverter is apt to be unstable under the grid impedance variation. To address this issue, this paper proposes the capacitor-current proportional-integral (PI) positive feedback active damping method that can ensure a positive equivalent resistance almost within the Nyquist frequency, i.e., the full controllable frequency range. In theory, the proposed damping method can be implemented by feeding back the capacitor current through a PI function. However, the integral term will continuously accumulate the noise and dc bias arising from the feedback signal. To overcome this drawback, a more practical implementation solution is drawn in this paper. Furthermore, a straightforward design procedure is presented for the convenience of selecting the proper controller parameters. With the proposed damping method and its practical implementation, high inverter robustness against the grid impedance variation can be achieved. Experiments are performed on a 6-kW prototype and the experimental results are in well agreement with the theoretical expectations. [ABSTRACT FROM AUTHOR]

In this paper, we design a voltage-modulated direct power control (VM-DPC) for a three-phase voltage source inverter (VSI) connected to a weak grid, where the phase-locked loop (PLL) system may make the system unstable if the conventional vector current control (VCC) method is applied. Compared with the conventional VCC method, the main advantage of the proposed VM-DPC method is that the PLL system is eliminated. Moreover, in order to inject the rated real power to the weak grid, the VSI system should generate some certain amount of reactive power as well. An eigenvalues-based analysis shows that the system with the proposed method tracks its desired dynamics in the certain operating range. Both simulation and experimental results match the theoretical expectations closely. [ABSTRACT FROM AUTHOR]

This paper presents the bilateral operation of a transformer-less H-bridge inverter as a power flow controller and fault current limiter in low-voltage distribution network. A novel control strategy has been developed to initiate and activate the H-bridge inverter to control the power flow at point of common coupling (PCC). On the other hand, the H-bridge inverter operation like a short-circuit current limiter during grid disturbance event and its smooth reinsertion after fault clearance have also been clarified. Besides, an island mode control strategy incorporating synchronization controller, and proper coordination with flip flops have been implemented in order to synchronize the microgrid with the main grid before reclosing the circuit breaker. The results confirm: The effectiveness and feasibility of the novel control methodology in activating the real power flow; the inverter capability of minimizing the short-circuit current during fault and the successful resynchronization of the microgrid voltage source inverter (VSI) and the H-bridge inverter to the main grid. [ABSTRACT FROM AUTHOR]

In islanded microgrids, voltage source inverters working in parallel are expected to provide regulation of the local frequency while granting active power sharing. This paper presents a local control approach at each inverter based on an event-driven operation of a parameter-varying filter. It ensures perfect active power sharing and controllable accuracy for frequency restoration without requiring the exchange of control data between inverters over the communication network. This paper includes stability analysis and design guidelines for the control parameters using a modeling approach that considers the interaction between inverters. Selected experimental results on a three-inverter laboratory microgrid corroborate the effectiveness of the proposed control scheme, and outlines its advantages with respect to previous similar schemes and the performance cost that implies not using communications. [ABSTRACT FROM AUTHOR]

The supply-side current of an inverter-fed induction motor (IM) is easily accessible and less affected by noises than the motor stator current. This paper proposes a novel sensorless speed estimation method for an IM using the spectrum of the supply-side current. However, due to the influence of fundamental supply frequency, it is difficult to carry out the speed detection straight from the supply-side current signal. In this paper, an analytic model for characterizing the supply-side current of an inverter-fed IM using the modulation theory and the switching function concept is developed. Then, the Hilbert transform is applied to extract the speed harmonic component from the supply-side current. Finally, an interpolated Goertzel algorithm is put forward to enhance the estimation precision of IM speed. The performance of the proposed sensorless speed estimation method is proved by the speed estimation results obtained from hardware experiments of an IM fed by an inverter under different load conditions. [ABSTRACT FROM AUTHOR]

Dynamic voltage instability (DVI) issues are the primary concern in low-voltage distribution network (DN) due to growing integration of low-inertia compressor motor loads such as air-conditioner and refrigerator. The concern of DVI is likely to increase owing to high penetration of rooftop type single-phase photovoltaic (PV) units in DN. On the other hand, DNs are inherently unbalanced as a result of load and line characteristics along with unbalanced PV penetration. This paper examines the impact of imbalance on the dynamic voltage stability (DVS) in DN and provides solutions to mitigate any adverse effects. Dynamic models of the single-phase PV units are developed and utilised in the paper. The degree of unbalanced is defined first, and then its impact on the DVS is investigated. From the investigation, it is observed that degree of instability is increased with the increment of imbalance. The paper has also proposed a mitigation strategy i.e. reactive power injection by PV inverter. Case studies are conducted on modified IEEE 4 bus system which represents a low-voltage DN. Results reveal that reactive power injection by PV inverter can improve the DVS by mitigating the impact of unbalance. [ABSTRACT FROM AUTHOR]

This paper presents the design and control of an advanced unidirectional DC/DC modular multilevel converter (MMC) that facilitate the integration of off-shore windfarms with the high-voltage direct current (HVDC) transmission system. The proposed converter deploys a single-phase MMC inverter coupled with series-connected rectifier modules through multiple medium frequency transformers. Unlike the conventional dq control method, which involves multiple transformations, this paper also proposes a simple control strategy that directly acts on the AC output of the MMC, under the stationary reference frame. [ABSTRACT FROM AUTHOR]

The automated and unattended design of balanced microstrip wideband bandpass filters by means of aggressive space mapping (ASM) optimization is reported in this paper. The proposed filters are based on multisection mirrored stepped impedance resonators (SIRs) coupled through quarter-wavelength transmission lines, acting as admittance inverters. Such resonant elements provide transmission zeros useful for the suppression of the common mode in the region of interest (differential filter pass band) and for the improvement of the differential-mode stopband (rejection level and selectivity). Due to the limited functionality of the inverters, related to the wide fractional bandwidths, the automated filter design requires a two-step process. With the first ASM, the filter schematic satisfying the required specifications (optimum filter schematic) is determined. Then, the layout is synthesized by means of a second ASM algorithm. Both algorithms are explained in detail and are applied to the synthesis of two filters, as illustrative (and representative) examples. With this paper, it is demonstrated that the two-step ASM optimization scheme (first providing the optimum schematic and then the layout), previously applied by the authors to wideband single-ended filters, can be extended (conveniently modified) to common-mode suppressed differential-mode bandpass filters. Thus, the value of this two-step ASM approach is enhanced by demonstrating its potential for the unattended design of complex filters, as those considered in this paper. [ABSTRACT FROM PUBLISHER]

This paper proposes a variable off-time control method for a single-phase microinverter operating in the discontinuous conduction mode (DCM) for efficiency improvement. First, the fixed off-time control method is analyzed. The concept is to fix the off-time of the active switch throughout a line cycle for all output powers and scale the on-time of the active switch to shape a sinusoidal output current. Then, based on the fixed off-time control method, a variable off-time control method is proposed to modulate the preset fixed off-time in order to decrease the switching frequency during ac line zero-crossings and light load conditions. Compared with existed fixed-frequency DCM control or boundary conduction mode control, the variable off-time control is more flexible to optimize the efficiency under different load conditions as the switching frequency range can be automatically adjusted according to the output power. The switching frequency is high at heavy loads to limit the maximum peak current and is low at light loads to increase the light load efficiency. In addition, a predictive on-time method is adopted to simplify inverter control and reduce hardware costs. The parameter design principle is detailed in this paper. A 300 W prototype is built to verify the performance of the proposed method. [ABSTRACT FROM AUTHOR]

This paper provides an experimental and theoretical discussion on dynamic braking for a medium-voltage induction motor fed by a modular multilevel double-star chopper-cell (DSCC) inverter. It is intended to apply the motor drive to large-capacity fans and compressors with a large moment of inertia. Each chopper cell consists of a bidirectional chopper and a braking chopper connecting a single small-rated braking resistor in series with a single IGBT. This configuration results in a “distributed” dynamic brake that provides a distinctive welcomed side effect of protecting all the bidirectional-chopper cells against sudden overvoltage. An experimental system rated at 400 V and 15 kW is designed, constructed, and tested to verify operating performance of the distributed dynamic brake. Experimental waveforms, along with simulated waveforms, confirm firmly that the distributed dynamic brake is feasible and effective in an induction motor fed by a medium-voltage high-power DSCC inverter for fans and compressors. Finally, this paper gives a design example of a distributed dynamic-braking resistor for the 11-kV, 12-MW induction motor driving a large-capacity fan equipped with a large moment of inertia. [ABSTRACT FROM AUTHOR]

The paper presents an economic evaluation, including a cost-benefit analysis and a sensitivity analysis, of smart photovoltaic (PV) inverters with a novel Watt-Var control scheme for enhancing PV penetration in distribution systems in Taiwan. The novel Watt-Var control scheme with three operation phases is utilized to avoid the voltage violation problem during peak solar irradiation period and increase the PV real power injection, and thus can get higher PV penetration in distribution systems. To evaluate the benefit and cost of the PV investment project, the annual revenue of PV power sales, the initial capital investment cost for a PV project with or without a smart inverter, and the operating and maintenance (O&M) cost are taken into account. The paper demonstrates the analyses of net present value (NPV) and benefit-cost ratio (BCR) for the PV project. In addition, the paper also presents a sensitivity analysis to deal with the project uncertainty with respect to some affecting parameters. The analyzing results show that, under the feed-in tariffs (FITs) policy, with proper selection of PV and smart inverter capacities, the investment can be profitable, and the smart PV inverter can greatly enhance the PV penetration in distribution systems in Taiwan. These results can provide some useful information for making policy to encourage investment in solar PV industry. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Konbin is the property of Air Force Institute of Technology (Instytut Techniczny Wojsk Lotniczych) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper proposes a method to suppress the resonant current circulating between integrated half-bridge modules with phase-leg capacitors in two legs. This circuit configuration has the advantage of low stray inductance between power semiconductor devices and dc-link capacitors (phase-leg capacitors). This paper presents an analysis of the equivalent circuit for the circuit configuration that suggests that the dc-link capacitor current will increase depending on the relationship between resonant and switching frequencies. The capacitor current was experimentally evaluated under pulse-width modulation operation at switching frequencies up to 100 kHz using SiC-mosfet s. As a result, the resonant current may occur in the dc side when the resonant frequency between phase legs was close to either the fundamental or the third harmonic of the switching frequency. In order to suppress the circulating resonant current, a graphite bus bar is applied to the phase-connecting bus bar. Using the graphite bus bar, the capacitor current can be reduced by 35% without any influence from the ac-side output current. [ABSTRACT FROM AUTHOR]

The traditional evaluation method of vehicle noise can no longer meet the requirements of electric vehicle as the sound character of electric powertrain (E-PT) is totally different from that of internal combustion engine vehicles. This paper presents a complete investigation of the sound quality of an E-PT. An acoustic test is conducted to analyze the sound character of E-PT, based on which the acoustic origins of E-PT including electromagnetic noise, gear whine, and inverter switching noise are studied. After that the sound quality of E-PT is investigated by objective and subjective evaluations. Subsequently, a sound quality model of E-PT based on support vector machine is established. The relative error testifies the effectiveness of the prediction model. The influence of the main noise origins on the sound quality of E-PT is determined. Finally, the structure of gearbox housing is redesigned based on topology optimization to improve the sound quality. The main original contributions of this paper are not only the sound quality method developed for E-PT but also improvement feasibility of sound quality. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure of Marx generator (MG) based on buck--boost converter is proposed to generate high-voltage pulses. In this structure, a single-phase inverter is employed to supply parallel diode--capacitor units by positive and negative values of the input dc source (±Vin). The main contribution of this paper is proposing a new switching strategy, by which a group of capacitors are charged properly. Finally, the charged capacitors are connected in series such that the output voltage is equal to summation of the capacitors' voltages. Considering specified value of the output voltage, the number of circuit elements in the proposed structure is reduced in comparison with other topologies of unipolar MG. Furthermore, voltage rating of switches and diodes in the proposed topology is lower than that of other unipolar MG structures. Design of the structure ensures that there is no need to connect the switches in series, when the number of stages is increased. To verify the performance of the proposed MG structure, simulation has been carried out in MATLAB/Simulink. Furthermore, a prototype of the proposed structure has been implemented in the lab. The simulation and experimental results confirm the capability of the structure for generating high-voltage pulses. [ABSTRACT FROM AUTHOR]

This paper describes the modeling, analysis, and design of a complete (dc-to-dc) inductive wireless power transfer (WPT) system for industrial moving applications. The system operates at 6.78 MHz and delivers up to 150 W to a load moving along a linear path, providing a quasi-constant dc output voltage and maintaining a zero voltage switching operation, regardless of position and load, without any retuning or feedback. The inductive link consists of an array of stationary transmitting coils and a moving receiving coil whose length is optimized to achieve a constant coupling coefficient along the path. Each Tx coil is individually driven by a constant amplitude and phase sinusoidal current that is generated from a GaN-based coupled load-independent Class EF inverter. Two adjacent transmitters are activated at a given time depending on the receiver’s position; this effectively creates a virtual series connection between the two transmitting coils. The Rx coil is connected to a passive Class E rectifier that is designed to maintain a constant dc output voltage independent of its load and position. Extensive experimental results are presented to show the performance over different loading conditions and positions. A peak dc-to-dc efficiency of 80% is achieved at 100 W of dc output power and a dc output voltage variation of less than 5% is measured over a load range from 30 to $500~\Omega $ . The work in this paper is foreseen as a design solution for a high-efficient, maintenance-free, and reliable WPT system for powering sliders and mass movers in industrial automation plants. [ABSTRACT FROM PUBLISHER]

The multilevel voltage-source inverter (VSI) topology of the series multicell converter developed in recent years has led to improved converter performance in terms of power density and efficiency. This converter reduces the voltage constraints between all cells, which results in a lower transmission losses, high switching frequencies and the improvement of the output voltage waveforms. This paper proposes an improved topology of the series multicell inverter which minimizes harmonics, reduces torque ripples and losses in a variable-speed induction motor drive. The flying capacitor multilevel inverter topology based on the classical and modified phase shift pulse width modulation (PSPWM, MPSPWM) techniques are applied in this paper to minimize harmonic distortion at the inverter output. Simulation results are presented for a 2-kW induction motor drive and the results obtained demonstrate reduced harmonics, improved transient responses and reference tracking performance of the voltage in the induction motor and consequently reduced torque ripples. [ABSTRACT FROM AUTHOR]

This paper discusses and compares phase-shifted pulse-width modulation (PS-PWM) and level-shifted PWM (LS-PWM) in a modular multilevel single-delta bridge-cell (SDBC) inverter for utility-scale grid-tied photovoltaic applications. This three-phase SDBC inverter provides the capability of operating even under power-distribution imbalances not only among three clusters, but also among cascaded bridge cells in each cluster. The main focus of this research lies in analyzing the capability of operation under severe power-distribution imbalances and presenting power-balancing methods based on zero-sequence current injection, which result in an extended power-balancing capability. This paper highlights that LS-PWM is superior to PS-PWM in both power-balancing capability and harmonic performance at the ac side of the SDBC inverter when operating under power-distribution imbalances. Experimental results obtained from a three-phase 10-kW downscaled system show good agreement with those from the theoretical analysis. [ABSTRACT FROM AUTHOR]

The traditional method of operating photovoltaic (PV) systems on the right side of the maximum power point (MPP) may cause the voltage to be close to the open‐circuit voltage of the PV panel, resulting in a large oscillation of the PV power. In contrast, the change in dP/dU value of the curve on the left of the MPP is small, which is more conducive to adjusting the output power of the PV. A frequency regulation control strategy is proposed for a single‐stage PV power plant (PVPP), maintaining the PV string operating on the left side of the MPP. This paper proposes an optimal step‐size calculation method based on the flexible power tracking evaluation function. This calculation method is suitable for PV operating on the left side of the MPP and can improve the dynamic and steady‐state performance of the PV power tracking process. In addition, the system response is analyzed by establishing a small‐signal model with PV operating on the left side of the MPP. Finally, simulations and experiments verify the correctness and accuracy of the proposed primary frequency regulation strategy and step‐size calculation method. [ABSTRACT FROM AUTHOR]

Thermal stress is one of the most important factors leading to power module failure. Under the load condition of high current with low fundamental frequency or largely changed load current, it would cause high junction temperature swing amplitude (JTSA) of chips, which could accelerate the failure of power module. To address this issue, this paper proposes a dual fuzzy logic controller‐based active thermal control (ATC) strategy to reduce the JTSA of chips in cases of variable power profiles. Two fuzzy logic controllers are designed to reduce the JTSA of chips by adjusting the switching frequency and pulse width modulation (PWM) strategy, respectively. One fuzzy logic controller is designed to reduce the transient JTSA of chips, which is done by changing the switching frequency according to the fundamental frequency and transient JTSA. The other one is to reduce the mean JTSA of chips, which is implemented by regulating the switching frequency and PWM modes according to the mean junction temperature and its variation. The minimum one is selected as the switching frequency of power inverter. Finally, the effectiveness of the proposed ATC strategy is verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

A fault current compensation technique is proposed in this paper for resonant grounded power distribution systems in bushfire prone areas. Arc suppression devices with residual current compensation inverters are used to compensate fault currents due to single line‐to‐ground faults in order to mitigate powerline bushfires. The main contribution of this paper is the design of a compensation technique for the T‐type residual current compensation inverter using a non‐singular terminal sliding mode control scheme. The main objective of the proposed scheme is to reduce the fault current and bring its value to a level so that it cannot ignite fires. The proposed controller is designed based on the selection of a sliding surface in a way the singularity problem can be avoided and chattering effects in existing sliding mode controllers can be eliminated. The desired current injection through the residual current compensation inverter is ensured by enforcing the control law into the terminal sliding surface where the control law is determined by satisfying the Lyapunov stability criteria. The performance of the non‐singular terminal sliding mode controller is compared with an integral sliding mode controller by considering different values of fault currents where these values are varied by changing fault resistances. Results for simulation in the software and processor‐in‐loop simulations are verified against operational standards which are essential for mitigating powerline bushfires. This work focuses to design a non‐singular terminal sliding mode controller for the residual current compensation inverter which is used in an arc suppression device to compensate both active and reactive components of the fault current and keeps its value below 0.5 A within 2 s after activating the residual current compensation inverter which is a requirement as per the operational standard. This controller is designed based on the selection of a terminal sliding surface while satisfying the condition for avoiding the singularity problem. [ABSTRACT FROM AUTHOR]

Transformerless inverters have become an important integration of the modern photovoltaic (PV) grid-tied systems. Unfortunately, it has a general safety problem regarding the earth leakage current that must be less than the recommended standards. Lately, the H7 transformerless inverter, which is a three-phase inverter with an additional switch on the DC side, is introduced to mitigate the earth leakage current. Different modulation techniques and controllers are proposed to optimize its performance. This paper proposed the application of model predictive control (MPC) to grid-connected H7 transformerless inverter supplied by the PV power system. In modeling the system, the grid inductance has been taken into consideration. The inverter is linked with the PV through a boost converter. It is found that the boost converter inductance value has a great effect on the leakage current. Matlab's simulations for the proposed system are carried out. The performance of the proposed system controlled by MPC is compared to that controlled by the proportional-integral (PI) controller. The results show that the MPC gives the system greater benefits than the PI controller. The effects of the boost-converter inductance on the earth leakage current are studied. Also, the design of the boost-converter inductance is introduced. [ABSTRACT FROM AUTHOR]

This paper presents a different Finite Control Set – Model Predictive Control (FCS-MPC) for grid-connected three-phase bidirectional power inverters. These are typically used in dc or ac renewable-based microgrids (MGs), where bidirectional operation and fast dynamic response is required. The bidirectional grid-connected inverters are an essential part of MG, which inject energy into the ac grid or demand energy from it. The dynamic behavior of the system is a major concern since the current can suddenly change depending on the hierarchical controller. This paper proposes a different cost function using sliding mode theory, which offers a good dynamic response, reduced computational burden, and a parameter-free control model. The operation principle of the proposed controller is given and evaluated using a Hardware-In-the-Loop (HIL) system, but also experimentally with a 1kW laboratory prototype. The final results demonstrate the advantages of using this approach in grid-connected three-phase bidirectional power inverters in terms of dynamic response and reduced computational burden, making this solution technically attractive and viable. [ABSTRACT FROM AUTHOR]

Inverter transformers are one of the key components in a PV plant and their operating patterns are considerably different from that of transformers in a substation. Moreover, these transformers experience higher level of harmonics generated by the inverters. Therefore, investigating the ageing profile of the inverter transformer is a timely requirement. In this paper, the ageing of inverter transformers in a medium-scale solar PV plant is studied by utilizing various real-time measurements including load current, top-oil temperature (TOT), ambient temperature, moisture in top oil, solar irradiance and individual current harmonics. An updated moisture-dependent thermal model (MDTMH), with consideration of current harmonics is developed to estimate the hot-spot temperature (HST). The influence of weather conditions, which directly determine the load current of inverter transformers on the loss of life (LOL) of an inverter transformer is also investigated. Furthermore, the effect of current harmonics levels on the inverter transformer's HST and LOL is explored. Finally, comparisons of HST and LOL of inverter transformers connected to PV arrays with three different tracking technologies, i.e., fixed-tilt, single-axis and Dual-axis PV arrays are performed. [ABSTRACT FROM AUTHOR]

With the large-scale integration of renewable energy systems, the power inertia and voltage support of the grid are low. Using the inverter with temporary storage capabilities cope with shortages and power fluctuations. This paper presents a new sensorless control of a single-phase grid-connected PV system based on a multilevel flying capacitor inverter MFCI) able to smooth out the power produced. The designed controller involves two cascade loops, an outer loop control extracts the maximum power despite climate change, and an inner loop consists of a model predictive control based on the Lyapunov theory for power factor correction and flying capacitor voltage balancing. Furthermore, an interconnected Kalman-like high-gain observer is combined with the predictive control algorithm to estimate the flying capacitor voltages accurately based on the actual grid current. The stability study of the suggested observer in the closed loop has been described. An algorithm that generates reference signals to manage power flows is also developed. The performance of the proposed controller has been verified on the MATLAB/Simulink platform, and the simulation results confirm the effectiveness of the proposed controller over different grid operating modes. • the proposed PV system is based on MFC inverter able to smooth out the grid-injected power. • The designed controller combines a Lyapunov-based model predictive control with a Kalman-like high-gain observer. • The PV conversion system optimizes energy extraction, injecting it smoothly into the grid. • The inverter, with temporary storage, copes with power fluctuations without external energy storage during grid faults. • The closed-loop stability of the controller is rigorously proved during the normal mode and grid fault conditions. [ABSTRACT FROM AUTHOR]

Copyright of Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji is the property of Gazi University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this paper, a photovoltaic (PV) microinverter capable of operating in both island mode and grid-connected mode by means of a reconfigurable control scheme is proposed. The main advantage of control reconfiguration is that in grid-connected mode, the microinverter works as a current source in phase with the grid voltage, injecting power to the grid. This is the operation mode of most commercial grid-connected PV microinverters. The idea is to provide those microinverters with the additional functionality of working in island mode without changing their control algorithms for grid-connected mode, which were developed and refined over time. It is proposed that in island mode, the microinverter control is reconfigured to work as a voltage source using droop schemes. These schemes consist in implementing P/Q strategies in the inverters, in order to properly share the power delivered to the loads. The aim of the paper is to show that the proposed control reconfiguration is possible without dangerous transients for the microinverter or the loads. Simulation and experimental results on an 180-W PV microinverter are provided to show the feasibility of the proposed control strategy. [ABSTRACT FROM PUBLISHER]

A recent paper by M. Zaky & M. Metwaly (doi: 10.1109/TPEL.2016.2583660) proposed a fuzzy logic controller (FLC) to mitigate the negative effects of motor parameter variation influence on indirect rotor field oriented control (IRFOC) without proposing a tuning method. However, neither rotor nor magnetizing inductances were investigated. Instead, the variation in stator resistance and load inertia—which have less effect on the orientation algorithm—is demonstrated. This correspondence introduces a typical system model with similar simulation platform and parameters. With identical tests, two errors to the original paper have been found. First, the reported speed which is in rev/min should be in rad/s. Second, the motor speed response to increasing inertia is opposite. The obtained results from the evaluation model confirm the claimed issues which conflict with the interpretations of the commented paper results. [ABSTRACT FROM AUTHOR]

Enhanced class E inverters (EFn or E/Fn) reduce the high peak switch voltage that is prevalent in class E inverters. Additionally, their stability and load regulation capabilities are improved as compared to class E inverters. This paper proposes an enhanced class E inverter (E/F3) with a piezoelectric transformer (PT) replacing the auxiliary resonant networks. This class E/F3 inverter is designed by adding a tuned auxiliary LC network at the third harmonic of the switching frequency to the class E inverter. Both the primary and auxiliary resonant networks are realized using a piezoelectric transformer (PT). The converter is simulated in LTspice and an experimental prototype is built and tested. It is found that the experimental results concur with the simulation results, with a measured efficiency of 90%. Thus, the theoretical design is verified and the concept of energy extraction is achieved. [ABSTRACT FROM AUTHOR]

This paper compares two finite-control-set model predictive control (FCS-MPC) strategies in the context of a grid-connected single-phase quasi-Z source inverter (SP-qZSI). Both schemes use discrete-time models of the inductor current and capacitor voltage for the DC side, as well as the output current on the AC side. To enhance the converter's performance, given the non-minimum phase characteristics of the DC side, a long prediction horizon is implemented for the predictive control. However, a horizon of this nature can be highly demanding in terms of processing load, rendering it inapplicable for some microcontrollers. To address this issue and mitigate the processing load, an alternative control strategy is presented that divides the total number of candidate solutions to be evaluated into smaller segments. The performance of the two control strategies is compared using total harmonic distortion (THD) and simulation times as evaluation metrics. The results indicate that the proposed strategy achieves significantly shorter simulation times than the compared control strategy when increasing the prediction horizon. Additionally, a reduction in the THD was observed in the proposed strategy, reaching an average of 2.8%, which is lower than the compared strategy that exhibited THD close to 3.5%. [ABSTRACT FROM AUTHOR]

Recent advancements in power electronics technology evolves inverter fed electric motors. Speed signals and rotor position are essential for controlling an electric motor accurately. In this paper, the sensorless speed control of surfacemounted permanent magnet synchronous motor (SPMSM) has been attempted. SPMSM wants a digital inverter for its precise working. Hence, this study incorporates fifteen level inverter to the SPMSM. A sliding mode observer (SMO) based sensorless speed control scheme is projected to determine rotor spot and speed of the multilevel inverter (MLI) fed SPMSM. MLI has been operated using a multi carrier pulse width modulation (MCPWM) strategy for generation of fifteen level voltages. The simulation works are executed with MATLAB/SIMULINK software. The steadiness and the heftiness of the projected model have been investigated under no loaded and loaded situations of SPMSM. Furthermore, the projected method can be adapted for electric vehicles. [ABSTRACT FROM AUTHOR]

To realize the efficient transient simulation of a grid-connected power generation system based on multiple inverters, this paper proposes a hybrid simulation method integrating the models of electromagnetic transient and dynamic phasors. Based on a demonstration of the concepts and properties of dynamic phasors, the models of single-phase and three-phase inverters described by dynamic phasors are established first. Considering the numerical compatibility problem between dynamic phasors and instantaneous values, an interface scheme between dynamic phasors and instantaneous values is designed, and the efficiency and precision differences of various transformation methods are compared in detail. Finally, by utilizing MATLAB/Simulink, a hybrid simulation platform of a multi-inverter grid-connected system is built, and the efficiency and accuracy of the hybrid simulation are validated via comparison with the full electromagnetic transient simulation. [ABSTRACT FROM AUTHOR]

In a capacitive power transfer (CPT) system, the coupling capacitance formed between the coupling plates is very small only in the pF or nF range, which leads to high voltage stress among the coupling plates during energy transmission, which increases the risk of an electrical breakdown between the coupled plates. To solve this problem, a novel dual-frequency CPT system is proposed in this paper, which uses the "peak clipping" effect caused by the superposition of the fundamental wave and third harmonic wave to reduce the voltage stress of the coupled plates. Through the detailed analysis of the working principle of the CPT system, it is shown that the dual-frequency CPT system can indeed reduce the high voltage stress among the coupled plate to 84.3% of the equivalent single-frequency system and can also reduce the inverter conduction losses to 90%. A 200 W prototype is designed with the proposed scheme, and the experimental results confirm the correctness of the theoretical derivation. [ABSTRACT FROM AUTHOR]

The Norton equivalent model based on the transfer function and the frequency domain analysis method for inverter resonance analysis lacks a comprehensive analysis of the resonant characteristics, and more information about the resonant key components and the degree of participation cannot be obtained. In this paper, a decomposed conductance model is proposed to characterize the resonance characteristics of the multi-inverter grid-connected system and the effect of the equivalent control link of the inverter on the resonance in more detail by combining the modal analysis method and the sensitivity analysis method. Firstly, based on αβ coordinates, the conductance division is carried out for the dual-loop inverter control link with the voltage external loop and current internal loop using capacitor-current feedback damping, and the inverter model based on the decomposition conductance is derived. The mathematical model of the multi-inverter grid-connected system is then established. Secondly, the resonance characteristics of the system are analyzed by combining the modal and frequency domain analysis methods when the number of inverters, inverter parameters, and grid-side impedance are changed. Thirdly, the degree of involvement of the system components, especially the equivalent control link of the inverter in resonance conditions, is determined in combination with the proposed model and the sensitivity analysis method, which is the basis for proposing an effective suppression strategy. Finally, a simulation model is built to verify the proposed method and the analysis results. [ABSTRACT FROM AUTHOR]

Neuromorphic computing is promising to become a future standard in low-power AI applications. The integration between new neuromorphic hardware and traditional microcontrollers is an open challenge. In this paper, we present an interface board and a communication protocol that allows communication between different devices, using a microcontroller unit (Arduino Due) in the middle. Our compact printed circuit board (PCB) links different devices as a whole system and provides a power supply for the entire system using batteries as the power supply. Concretely, we have connected a Dynamic Vision Sensor (DVS128), SpiNNaker board and a servo motor, creating a platform for a neuromorphic robotic system controlled by a Spiking Neural Network, which is demonstrated on the task of intercepting incoming objects. The data rate of the implemented interface board is 24.64 k symbols/s and the latency for generating commands is about 11ms. The complete system is run only by batteries, making it very suitable for robotic applications. [ABSTRACT FROM AUTHOR]

This paper proposes thermometer‐code latches having five and six transistors for unidirectional and bidirectional thermometer‐code shift‐registers, respectively. The proposed latches omit the set and reset transistors by changing from two supply voltage nodes to the set and reset signals in the cross‐coupled inverter. They set or reset the data by changing the supply voltage to ground in either of two inverters. They reduce the number of transistors to five and six compared with the conventional thermometer‐code latches having six and eight transistors, respectively. The proposed thermometer‐code latches were simulated using a 65 nm complementary metal‐oxide‐semiconductor (CMOS) process. For comparison, the proposed and conventional latches are adapted to the 64 bit thermometer‐code shift‐registers. The proposed unidirectional and bidirectional shift‐registers occupy 140 μm2 and 197 μm2, respectively. Their consumption powers are 4.6 μW and 5.3 μW at a 100 MHz clock frequency with the supply voltage of 1.2 V. They decrease the areas by 16% and 13% compared with the conventional thermometer‐code shift‐register. [ABSTRACT FROM AUTHOR]