Search

Abstract: For the first time, a specially designed pressure retarded osmosis (PRO) hollow fiber membrane has been successfully developed and applied in the PRO process to demonstrate its potential for power generation. The membrane fabrication method is similar to that used for making thin-film composite (TFC) forward osmosis hollow fiber membranes, but further optimization and improvement have led to a new type of TFC hollow fiber membranes with much greater mechanical strength in addition to its excellent separation property and high water flux. The TFC PRO hollow fiber membranes have a water permeability (A) of 9.22×10−12 m/(sPa), salt permeability (B) of 3.86×10−8 m/s and structural parameter (S) of 4.6×10−4 m. It can withstand hydrostatic pressure as high as 9bar with its relatively large dimension of 0.98mm lumen diameter. This PRO hollow fiber membrane is superior to all other PRO membranes reported in the open literature in terms of power density. A power density as high as 10.6W/m2 can be achieved using seawater brine (1.0M NaCl) and wastewater brine (40mM NaCl), which suggests that the newly developed PRO hollow fiber membrane has great potential to be applied in PRO processes to harvest salinity gradient energy. A higher pressure is preferred as it allows generation of higher power density (pressures of 12bar may be optimal for seawater as the high salinity stream), and this can be realized by reduced fiber dimension. Further optimization of the membrane structure will be performed. [Copyright &y& Elsevier]

Abstract: Forward osmosis (FO) has received intensive studies recently for a range of potential applications such as wastewater treatment, water purification and seawater desalination. One of the major challenges to be overcome is the lack of an optimized FO membrane that can produce a high water flux comparable to commercial RO membranes. Two types of thin-film composite FO hollow fibers with an ultra-thin polyamide-based RO-like skin layer (300–600nm) on either the outer surface (#A-FO) or inner surface (#B-FO) of a porous hollow fiber substrate have been successfully fabricated. These novel composite FO hollow fibers have been characterized by a series of standard protocols and benchmarked against commercially available FO flat sheet membranes and reported NF hollow fibers used for the FO process. The characterization reveals that the FO hollow fiber membranes possess a large lumen. The substrates are highly porous with a narrow pore size distribution. The active layers present excellent intrinsic separation properties with a hydrophilic rejection layer and good mechanical strength. The #B-FO hollow fiber membrane can achieve a high FO water flux of 32.2L/m2 h using a 0.5M NaCl draw solution in the active rejection layer facing draw solution (AL-facing-DS) configuration at 23°C. The corresponding salt flux is only 3.7g/m2 h. To the best of our knowledge, the performance of the #B-FO hollow fiber is superior to all FO membranes reported in the open literature. The current study suggests that the optimal FO membrane structure would possess a very small portion of sponge-like layer in a thin and highly porous substrate, which suggests a way for further improvement. [Copyright &y& Elsevier]

Pressure retarded osmosis (PRO) has been identified as a promising technology to harvest the salinity gradient energy. For practical applications of PRO process, membrane fouling is a challenging issue as it leads to severe decline of PRO performance in terms of water flux and power density. It is imperative to develop anti-fouling membranes for PRO process. The current study demonstrated the unique roles and the great potential of aminosilane in developing anti-fouling thin film composite (TFC) PRO membranes. Experimental results revealed that aminosilane as a grafting agent can modify both the support layer (interior) and the selective layer of PRO membranes with remarkably enhanced hydrophilicity via a very simple grafting procedure. In the grafting, aminosilane was able to minimize the pore-blocking issue with almost no increase in the membrane structural parameter ( S ). Meanwhile, the membrane mechanical strength was well maintained with the grafting due to the capability of aminosilane as a cross-linker. With enhanced hydrophilicity, it was interestingly found that the water permeability ( A ) was doubled, while the salt rejection was maintained nearly unchanged. The combination of these effects brought in remarkably enhanced water flux, power density and anti-fouling property to the resultant membrane. [ABSTRACT FROM AUTHOR]

Abstract Forward osmosis (FO) membranes have received attention as an energy-efficient and low-cost technique in stream concentrating processes. In this work, a novel double-skinned hollow fiber thin film composite (TFC) FO membrane has been successfully fabricated, which consists of a one-step prepared dual layer substrate and a thin inner selective layer formed via interfacial polymerization. The substrate consists of a relatively dense ultrafiltration (UF) outer layer and a porous UF inner layer, both of which were constructed from polyethersulfone (PES) as the substrate material by using dual-layer co-extrusion technique. Compared to the commercial and reported double-skinned FO membranes, the FO membrane developed in this work exhibited a higher permeate flux with humic acid solution as feed. Furthermore, the double-skinned FO membrane was applied in concentrating activated sludge using 0.5 M NaCl as draw solution, and a permeate flux at 5.4 L/m2h was achieved after 5 h operation, which was higher than or comparable to those of the reported FO membranes. Membrane autopsies and foulant analysis suggested that the dense UF skin layer helped to reject greater-sized organic foulants (> 300 Da). This study shed light on the important fabrication features and promising application of the double-skinned hollow fiber TFC FO membrane in sludge concentration. Graphical abstract fx1 Highlights • A dual-layer UF substrate was prepared via a single-step fabrication process. • TFC FO membrane was fabricated via interfacial polymerization in the lumen of the substrate. • FO performance in sludge thickening process was investigated. • Tight UF layer helped rejecting greater-sized organics in sludge. • A permeate flux of 5.4 L/m2h was achieved after 5 h operation using 0.5 M NaCl as draw solution. [ABSTRACT FROM AUTHOR]

The emerging thin film composite (TFC) forward osmosis (FO) and pressure retarded osmosis (PRO) membranes generally have better separation properties compared with their cellulose triacetate (CTA) counterparts. Nevertheless, their scaling performance has been rarely reported. In the current study, the phenomenon of membrane integrity loss as a result of scaling is reported for the first time for osmotically driven membrane processes (ODMPs). The results show that the TFC membrane suffered marked flux reduction during the scaling in the active-layer-facing-feed-solution (AL-FS) orientation, accompanied with the severe damage of the membrane active layer. The membrane integrity loss is attributed to the scale formation and growth in the confined space between the membrane and the feed spacer. Compared with the CTA membrane, the TFC was more prone to scaling and membrane damage due to its unfavorable physiochemical properties (presence of Ca 2 + binding sites and ridge-and-valley roughness). Although antiscalant addition was shown to be effective for scaling control in AL-FS, it was ineffective in the active-layer-facing-draw-solution orientation. The current study reveals the critical need for scaling control in ODMP processes with respect to the membrane integrity and flux stability. The results also have far-reaching implications for FO and PRO membrane design and process operation. [ABSTRACT FROM AUTHOR]

Abstract: Polyamide thin film composite (TFC) membranes with tailored porous substrate and rejection layer are promising for forward osmosis (FO) applications. The current study investigates the effect of rejection layer synthesis conditions on the performance of the resulting TFC polyamide FO membranes. The influence of monomer concentrations (i.e., m-phenylenediamine (MPD) and trimesoyl chloride (TMC) concentrations) on the membrane separation properties as well as FO performance was systematically studied. A strong trade-off between the water permeability and salt rejection was observed, where increasing the TMC concentration or reducing the MPD concentration resulted in higher membrane permeability but lower salt rejection. In FO tests, membranes with poor salt rejection had severe solute reverse diffusion, which enhanced the internal concentration polarization (ICP). It was found that the FO water flux was governed by both the membrane water permeability and its solute rejection. For a membrane with higher water permeability but lower solute rejection, the reduced membrane frictional resistance was compensated by the simultaneously more severe solute-reverse-diffusion-induced ICP. The net effect on the FO water flux depends on the competition of these two opposing mechanisms. Under conditions where solute reverse diffusion may cause severe ICP (e.g., high draw solution concentration and high water flux level), membranes need be optimized to achieve a high salt rejection even if this is at the expense of lower water permeability. [Copyright &y& Elsevier]