Search

This article proposes a systematic synthesis method to identify the optimum converter topology for a specified voltage conversion ratio. This gain-oriented converter synthesis is formulated as an inverse problem around the inductor flux balance equations. The proposed synthesis method consists of two processes. A set of distinct converter topologies is first synthesized from the specified voltage conversion ratio by obtaining the solutions for a set of six inverse equations in twelve unknowns. The optimal topology for any intended application can be identified based on the desired performance metrics. The complete synthesis method is illustrated with quadratic buck–boost gain as an example. In total, 25 distinct topologies are synthesized using the first process, and their feasibility is validated by PLECS simulation. In total, three case studies are reported to explain the second process. Ground-referenced output and the minimum number of switches are used as the first two selection criteria in all the case studies. Minimum peak inductor current, minimum component stress factor, and minimum voltage and current stress are the third selection criterion in Case Studies-1, 2, and 3, respectively. The steady-state operations of two optimal converters selected in Case Study-1 were verified experimentally. [ABSTRACT FROM AUTHOR]

This article presents an analytical method to derive an optimum converter topology for a specified voltage conversion ratio (G). An optimum topology for any given G can be identified after obtaining the comprehensive pool of converter topologies. This gain-oriented converter synthesis is formulated as an inverse problem around the principle of inductor flux balance. A step-by-step method is proposed to solve the inverse problem and obtain a comprehensive set of non-redundant converter topologies for any given voltage conversion ratio. Consequently, the number of possible converter topologies for a specified voltage conversion ratio is also identified. The optimum converter topology is chosen from the comprehensive set based on three selection criteria, viz., ground-referenced output, a minimum number of switches, and minimum peak inductor current. The proposed solution methodology is illustrated with quadratic boost and quadratic buck gains as case studies. A comprehensive set of non-redundant topologies is identified in both cases. The steady-state operations of all the topologies are studied with PLECS simulation. Based on the selection criteria, an optimum topology is selected in each case, and their steady-state operation is verified experimentally using lab-developed prototypes. [ABSTRACT FROM AUTHOR]

Impedance source inverters (ISIs) are gaining attention due to features such as single-stage conversion, buck-boost capability, and inherent shoot-through protection. To maintain the required ac output voltage, typically ISIs are operated at a higher dc-link voltage due to constrained modulation index. This also increases voltage stress across capacitors and switches of the converter. This voltage stress is approximately double compared to that of voltage source inverter with preboost stage (Boost-VSI). To mitigate this problem, a new pulsewidth modulation (PWM) scheme for the active-front-end based ISIs (AFE-ISIs) is proposed. The proposed scheme enables the ISIs to produce high ac gain with lower voltage stress across the capacitor and switches. In other words, the proposed scheme blends the advantages of Boost-VSI into ISIs. With the new PWM scheme, there are also reductions in output voltage total harmonic distortion, switching frequency ripple in the inductor current, and power loss in the converter. A prototype of the current-fed switched inverter, an AFE-ISI, is designed, and the proposed PWM scheme is implemented. Experimental results obtained are in accordance with the proposed theory and show that the voltage stress has reduced from 325 V to 203 V for an ac output of 110 V. [ABSTRACT FROM AUTHOR]

Buck-converter-based topologies are used to generate high-frequency sinusoidal outputs. Buck-based inversion circuits such as voltage source inverters or class-D amplifiers have inherent control-to-output linearity in large-signal sense. However, in these topologies, the instantaneous output is always smaller than the dc-input during linear modulation. A differential boost inverter (DBI) is a boost-based topology that is used to generate a sinusoidal output. In DBI, the instantaneous output can be higher or lower than the dc-input voltage. DBI exhibits nonlinear control-to-output behavior in large-signal dynamic sense. Therefore, generating a high-frequency sinusoidal output using this topology is a challenge. The issues associated with a DBI for high-frequency sine wave generation are characterized in this paper. Conventional linear and nonlinear control techniques fail to produce a high-quality sine wave output at higher operating frequency. A nonlinear feedback linearization technique is proposed, which forces the output to be linear with respect to the reference even at higher operating frequency. This leads to a high-frequency high-quality sine wave generation using a DBI. The proposed modulator is verified using a laboratory prototype to generate a sine wave up to 2 kHz. A triangular wave of 100-Hz frequency is also generated by the proposed technique. Superior dynamic responses of a dynamic linearizing modulator controlled DBI for a step change in frequency, load current, input voltage, and reference are also experimentally verified. [ABSTRACT FROM AUTHOR]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

Electronic load (E-load) is commonly used to test power supplies. In order to test computer power supplies, the E-load must possess an ideal controlled current source property which draws a desired load current even in the case of a very low terminal voltage of the source under test (SUT). It also needs to have superior dynamic performance to simulate high-slew-rate load transients. This paper proposes the design of a switching-converter-based E-load with very large operational bandwidth. The overall architecture of the E-load consists of a low-bandwidth converter, which functions under steady state, and a high-bandwidth auxiliary circuit that is only active during transient state. The converter circuit is realized using a novel switched-boost topology, and the auxiliary circuit is realized using a MOSFET operating at the edge of saturation and linear region. The proposed topology is capable of sinking a specific amount of load current even with a very low SUT terminal voltage. Simulation and experimental validations are provided to verify the proposed concepts. A prototype has been built to test the proposed architecture. The operational input voltage (SUT voltage) ranges of the prototype are between 0.5 and 6 V. The load current range is between 0.75 and 7 A. The results validate the excellent dynamic characteristics of the proposed architecture. [ABSTRACT FROM PUBLISHER]

In this paper, the performance of voltage-source converter-based shunt and series compensators used for load voltage control in electrical power distribution systems has been analyzed and compared, when a nonlinear load is connected across the load bus. The comparison has been made based on the closed-loop frequency response characteristics of the compensated distribution system. A distribution static compensator (DSTATCOM) as a shunt device and a dynamic voltage restorer (DVR) as a series device are considered in the voltage-control mode for the comparison. The power-quality problems which these compensator address include voltage sags/swells, load voltage harmonic distortions, and unbalancing. The effect of various system parameters on the control performance of the compensator can be studied using the proposed analysis. In particular, the performance of the two compensators are compared with the strong ac supply (stiff source) and weak ac-supply (non-stiff source) distribution system. The experimental verification of the analytical results derived has been obtained using a laboratory model of the single-phase DSTATCOM and DVR. A generalized converter topology using a cascaded multilevel inverter has been proposed for the medium-voltage distribution system. Simulation studies have been performed in the PSCAD/EMTDC software to verify the results in the three-phase system. [ABSTRACT FROM AUTHOR]

This paper proposes a flying-capacitor-based chopper circuit for dc capacitor voltage equalization in diode-clamped multilevel inverters. Its important features are reduced voltage stress across the chopper switches, possible reduction in the chopper switching frequency, improved reliability, and ride-through capability enhancement. This topology is analyzed using three-and four-level flying-capacitor-based chopper circuit configurations. These configurations are different in capacitor and semiconductor device count and correspondingly reduce the device voltage stresses by half and one-third, respectively. The detailed working principles and control schemes for these circuits are presented. It is shown that, by preferentially selecting the available chopper switch states, the dc-link capacitor voltages can be efficiently equalized in addition to having tightly regulated flying-capacitor voltages around their references. The various operating modes of the chopper are described along with their preferential selection logic to achieve the desired performances. The performance of the proposed chopper and corresponding control schemes are confirmed through both simulation and experimental investigations. [ABSTRACT FROM AUTHOR]

The paper discusses the operating principles and control characteristics of a dynamic voltage restorer (DVR). It is assumed that the source voltages contain interharmonic components in addition to fundamental components. The main aim of the DVR is to produce a set of clean balanced sinusoidal voltages across the load terminals irrespective of unbalance, distortion and voltage sag/swell in the supply voltage. An algorithm has been discussed for extracting fundamental phasor sequence components from the samples of three-phase voltages or current waveforms having integer harmonics and interharmonics. The DVR operation based on extracted components is demonstrated. The switching signal is generated using a deadbeat controller. It has been shown that the DVR is able to compensate these interharmonic components such that the load voltages are perfectly regulated. The DVR operation under deep voltage sag is also discussed. The proposed DVR operation is verified through the computer simulation studies using the MATLAB software package. [ABSTRACT FROM AUTHOR]

This paper examines the application of a diodeclamped multilevel inverter (DCMLI).based distribution static compensator (DSTATCOM) connected to a three-phase, four-wire (3p4w) distribution system. The DCMLI has an inherent unbalancing problem among its dc capacitor voltages. Additionally, when the load contains a dc part, the neutral point of the compensator also becomes unbalanced. In this paper, the effects of different loading conditions on the dc capacitor voltages of the inverter are studied. Two new control circuits are proposed for equalizing the capacitor voltages. Different control techniques are presented for the equalizing circuits. Equations of the proposed equalizing controllers are developed corresponding to the control of the switching devices. Comparative studies of different control techniques and the performances of the two controllers are performed. Simulation studies are performed using PSCADIEMTDC to validate the efficacy of the proposed equalizing controller circuits. [ABSTRACT FROM AUTHOR]

In this paper, the method of triangular carrier switching control of two-level inverters is extended to cascaded multilevel inverters using phase-shifted multicarrier unipolar pulsewidth modulation (PWM). The condition for smooth modulation is obtained using the Bessel's function representation of the PWM output and the switching condition of the multilevel- inverter-controlled system. A method is proposed for the determination of the minimum amplitude of the triangular carrier for smooth modulation at fixed switching frequency. It is shown that the multilevel modulation based on the phase-shifted carriers significantly reduces the ripple magnitude in the switching function and allows the use of a smaller carrier amplitude under closed loop. This increases the forward gain and, hence, improves the tracking characteristics. The proposed cascaded multilevel inverter control is implemented for the operation of a distribution static compensator (DSTATCOM) in the voltage control mode. The experimental verification of the theoretical and simulation results is provided through a field-programmable gate array (FPGA) based control of a laboratory model of a single-phase DSTATCOM. [ABSTRACT FROM AUTHOR]

Flying capacitor multilevel inverter (FCMLI) is a multiple voltage level inverter topology intended for high voltage and power operations with low distortion. It uses capacitors, called flying capacitors for clamping the voltage across the power semiconductor devices. In this paper, the implementation of a distribution static compensator (DSTATCOM) using an FCMLI is presented. A hysteresis current control technique for controlling the injected current by the FCMLI-based DSTATCOM is discussed. A new method for controlling the flying capacitor voltages is proposed which ensures that their voltages remain constant and at the same time maintain the desired current profile under the hysteresis current control operation. Simulation studies are performed using PSCAD/EMTDC to validate the efficacy of the control scheme and the FCMLI-based DSTATCOM. [ABSTRACT FROM AUTHOR]

This paper proposes a new connection for a unified power quality conditioner (UPQC) to improve the power quality of two feeders in a distribution system. A UPQC consists of a series voltage-source converter (VSC) and a shunt VSC both joined together by a common dc bus. It is demonstrated how this device is connected between two independent feeders to regulate the bus voltage of one of the feeders while regulating the voltage across a sensitive load in the other feeder. Since the UPQC is connected between two different feeders (lines), this connection of the UPQC will be called an interline UPQC (IUPQC). The structure, control and capability of the IUPQC are discussed in this paper. The efficacy of the proposed configuration has been verified through simulation studies using PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]