Search

Toilet paper has been reported as one of the major insoluble pollutant components in the influent of wastewater treatment plants. Toilet paper fibers contribute to a large production of sewage sludge, resulting in a high treatment cost and high energy consumption. To find energy-efficient, cost-effective, and environment-friendly technologies for fiber removal and resource recovery from wastewater, a life-cycle assessment (LCA) was performed to analyze the wastewater treatment processes, including a sieving process for removing and recovering suspended solids before the biodegradation units. Based on the LCA results, it was estimated that the sieve screening process saved 8.57% of energy consumption. The construction phase of sieving consumed 1.31% energy cost compared with the operation phase. Environmental impact analysis showed that sieving reduced the impacts of climate change, human toxicity, fossil depletion, and particulate matter formation, which reduced the total normalized environmental impacts by 9.46%. The life-cycle analysis of the removal of toilet paper fibers from wastewater revealed the need to use more efficient methods to enhance the recovery of cellulose fibers. [ABSTRACT FROM AUTHOR]

In traditional paper pulp deinking, sodium hydroxide (NaOH) is used as a hydrolysing agent for fibers in concentrations that set the pH of the medium to values greater than 10; however, substantial amounts of solid and liquid waste are created, and their management is problematic and dangerous. Recently, the implementation of biological treatments, for example, enzymatic deinking, is presented as an option to deink mixed office prints at neutral pH; that is, with the minimum use of chemical reagents and, therefore, better waste management and less environmental impact. The main objective of this research work is to study the mechanism of hydrolysis, detachment and ink capture in the bubble-enzyme-ink particle system, during the deinking of office paper type MOW (Mixed Office Waste), using a laboratory column flotation. The cellulase enzyme Trichoderma sp. was used. To compare the deinking efficiency of office paper using enzymes, deinking experiments were performed according to the traditional procedure using sodium hydroxide. The quality of the deinked fibers by measuring their optical properties (whiteness, reflectance, opacity, black spots and tonality) was performed in the Laboratory of the Paper Industry Bio Papel Scribe SA de CV, located in the city of Morelia, Michoacán, México. The operational variables of the flotation column were established through experiments in the water-air system and adding 100 ppm of pine oil as a surfactant (surface tension of the liquid in 56.6 dynes / cm). The superficial air flowrate was set at 1.27 cm / s (6 LPM), whereas the pulp feed flow rate was 0.88 cm / s. The experimental results show the feasibility of recycling MOW-type office paper by using the enzyme cellulase Endo-β-1,4-D-glucanase and the amino acids Aspartate, Glutamate and Asparagine; the latter, individually and mixed. The optical properties of the sheets of paper formed with the cellulose deinked by this procedure, were better than those evaluated to sheets of paper formed with fibers of recycled and deinked paper by the traditional procedure. In the case of the combined use of the three amino acids, the ISO whiteness is 90.8%, 303.4 ppm of black spots, reflectance of 47.1% and 89.5 of opacity. By the traditional procedure, the reported whiteness is 80.2%, the reflectance is 57.4%, and the opacity is 99.6%. [ABSTRACT FROM AUTHOR]

• The study aimed to quantify the cyclic dominance resembling rock-paper-scissors observed in the optional prisoner's dilemma, considering cooperators, defectors, and loners as the three competing strategies. • The research utilized theoretical and numerical analyses to explore the impact of environmental feedback on the replicator dynamics. • The rate of environmental replenishment and the payoff from draw games were identified as crucial factors influencing gameplay dynamics. • The study revealed that the loner's payoff and the strength of the dilemma played pivotal roles in determining the dominant strategies. This research investigation delves into the concept of cyclic dominance and its interplay with environmental feedback within the framework of the Optional Prisoner's Dilemma (OPD) game. A quantitative model has been meticulously constructed to encompass both the OPD and Rock-Paper-Scissors (RPS) games, wherein the outcomes are contingent upon environmental feedback. The intricate relationship between player populations and their surrounding environment is elucidated through the utilization of replicator dynamics. The empirical findings of this study shed light on the existence of distinct equilibria contingent upon the prevailing environmental circumstances. Under scenarios characterized by resource depletion, an equilibrium state emerges wherein only solitary individuals (referred to as "loners") persist. Conversely, under conditions of resource replenishment, an equilibrium is established where various strategic approaches coexist in equal proportions, akin to the dynamics of the Rock-Paper-Scissors game. Notably, cyclic dominance manifests itself during periods characterized by intermediate environmental conditions. Several pivotal factors have been identified as determinants of these dynamic phenomena, including the rate of environmental replenishment, the strength of the dilemma presented, the payoff for loners, and the reward for a draw. It has been empirically demonstrated that the presence of extreme values in the replenishment rate, irrespective of whether exceptionally high or exceptionally low, serves as an impediment to the emergence of cyclic dominance. This model underscores the substantial influence of environmental feedback on social dilemmas, particularly in the context of the OPD game, ultimately leading to the emergence of competitive cyclic dominance games reminiscent of the Rock-Paper-Scissors game. In doing so, it elucidates the intricate interplay between evolutionary game incentives and the dynamics of the surrounding environment. [ABSTRACT FROM AUTHOR]

The aim of this work is to compare the environmental impacts of two production processes of tissue paper using virgin pulp (virgin fiber) or waste paper pulp (recycled fiber). This comparison is based on the materials and energy used as well as emissions and waste resulting from the production of tissue paper. Life cycle assessment (LCA), ReCiPe method, was chosen as the analysis tool. The results of the research proved that electricity has the most considerable participation in the overall environmental impacts in both production processes, followed by either virgin pulp or heat. Consequently, these two production processes are the greatest contributors to the following midpoint environmental impact categories: human toxicity, climate change, human health and ecosystems, and fossil depletion. The analysis based on endpoint impact categories proved that the production process based on waste paper is more environmentally friendly than the one based on virgin pulp in all impact categories: human health, ecosystems, resources. This is largely because of its lower material and energy requirements in the entire life cycle. Due to the fact that the tissue paper is the final use of fiber, using recycled waste paper is strongly recommended. The obtained research results are a valuable source of management information for the decision makers at both company and national levels required to improve the environmental performance of tissue paper production. [ABSTRACT FROM AUTHOR]

This study compares the environmental performance of Mexican banknotes printed on high-durability cotton paper (HD paper) and thermoplastic polymer (polymer) through a life cycle assessment to appraise the environmental impacts from the extraction of raw materials to the final disposal of the banknotes. The functional unit was defined considering the next parameters: 1) lifespan of the banknotes, stablished in 31.5 and 54 months for HD paper and polymer, respectively; 2) denomination, selecting $200 pesos banknotes; 3) a 5 year time frame and 4) a defined amount of money, in this case stablished as the monthly cash supply of an average Mexican household, equaling $12,708 pesos. Accordingly, 121 pieces for the HD paper and 71 pieces for the polymer banknotes were analyzed. The results favor the banknotes printed on polymer substrate primarily because of the longer lifespan of this type of material; however, there is a considerable environmental impact in the stages of distribution, followed by the extraction of the raw materials (crude oil) during manufacturing. Regarding the HD cotton paper, the major impact corresponds to extraction of the raw materials, followed by the distribution of the banknotes. The inclusion of the automatic teller machines (ATMs) in the life cycle assessment of banknotes shows that the electricity required by these devices became the largest contributor to the environmental impacts. Additionally, the sensitivity analysis that the average lifetime of the banknotes is a determining factor for the environmental impacts associated with the whole life cycle of this product. The life cycle stages that refer to the extraction of the raw materials, combined with the average lifetime of the banknotes and the electricity required during the usage stage, are determining factors in the total environmental impact associated with Mexican banknotes. [ABSTRACT FROM AUTHOR]

Purpose - Demanding customers, legislation and raw materials shortages in the modern world have forced companies to minimize the system's environmental impact. The paper seeks to analyze the economic impact of blending in sustainable paper industries in countries such as India. Design/methodology/approach - A linear programming model for a paper supply chain is proposed to minimize paper manufacturing cost by optimally blending wood pulp and after-use paper under various conventional supply chain constraints. The issues of quality, environmental concern and reusability in the paper industry have also been taken into account. Findings - Improving quality of after-use paper by proper recovery network reduces the manufacturing cost. Increasing proportion of wood fiber in the finished paper decreases the cost, even at the cost of degradation in the environment. Thus, it is up to the manufacturer to reflect its degree of environmental concern to the government and society by assigning appropriate environmental and quality opportunity costs in the model. Research limitations/implications - Difficulty in obtaining the estimates of the environmental and quality cost is a major limitation of the study. Practical implications - This research provides manufacturers with a simple mathematical model to compare the economic feasibility of blending wood pulp and after-use paper depending on the market situation. Originality/value - The major contribution of the model is its capability to study the economic impact of blending by considering some of the important sustainable development issues like environment, quality, shortage, and reusability under one objective function. [ABSTRACT FROM AUTHOR]

Paper manufacturing industries depend mainly on forests for wood, which is the basic raw material. Forest plays an important role in balancing the ecosystem to protect forest deinking and bleaching (recycling) of waste paper had gained a lot of importance. Conventional chemical deinking processes require large amount of chemicals which are toxic and hazardous to the environment, hence other effective deinking methods are needed. Enzymatic deinking (cellulolytic, hemicellulolytic and ligninolytic) has attracted enormous attention because of high efficacy and minimum environmental impact. For bleaching, enzymatic action (individual as well as in combination), along with physical treatment, makes the pulp more accessible to the chemicals and also to the amount of chemicals required to obtain similar levels of brightness. Strength properties and brightness of the pulp are improved by these treatment methods. With minimum impact on the environment, this review gives comprehensive information about the various methods used for the recycling of waste paper. [ABSTRACT FROM PUBLISHER]

Purpose The aim of this work is to quantify the greenhouse gas (GHG) emissions savings potential in magazine paper production through the application of the innovative manufacturing strategies using advanced sheet structure design and fibre modifications. Methods The study applies Life Cycle Assessment (LCA) methodology to two different magazine paper products: supercalendered (SC) paper and light-weight coated (LWC) paper. A cradle-to-gate approach is used aiming to assess the environmental benefits gained through the implementation of new manufacturing strategies in both products. The functional unit of the system was defined as the production of one square meter of finished paper for printing magazines. Conventional and new production processes have been compared. Results and discussion The strategies applied to SC paper resulted in reduction of GHG emissions by 22.9%, with a total of 10.7 gCO 2 eq emissions saved per square meter of SC paper. In the case of LWC paper, GHG emissions are reduced by 20.3%, which are equal to a total of 19.7 gCO 2 eq saved per square meter of LWC paper. The influence of certain methodological approaches -functional unit, electricity mix and avoided impacts- in the final results is also discussed in the paper. Conclusions The manufacturing strategies implemented show a remarkable potential for reducing GHG emissions. Taking into account that the pulp and paper industry is a very energy-intensive sector and one of the main GHG emitters, the potential of the strategies for the improvement of the environmental performance of the papermaking processes is significant. [ABSTRACT FROM AUTHOR]

This review proposes, for the first time, a recent overview of ecological information involving electrochemical paper-based analytical devices (ePADs) dedicated to sensing environmental and clinical situations. The options of manufacturing methods are screen printing, stencil printing, pencil drawing, laser scribing, inject-printing, and additive printing. We have covered ecological aspects such as resource efficiency, safety, and toxicity regarding using paper-based (bio) electrodes. To see the ecological impact of testing methods by using ePADs, the Analytical GREEnness (AGREE) approach was utilized as a greenness metric calculator model since the tool makes use of 12 principles of Green Analytical Chemistry. Positive and negative concepts from the revised values of AGREE metric of clinical and environmental analysis were introduced and discussed. Also, we finalize the present review informing the life cycle of ePAD and some challenges that can impact the next generation of disposable electrodes. • The greenness metrics involving paper-based electrochemical (bio)sensors have been reviewed. • Ecological impact for environmental and clinical analysis was introduced using the AGREE approach. • Resource efficiency, safety, and toxicity regarding using paper-based (bio)electrodes are discussed. • The life cycle and challenges that can impact the next generation of disposable electrodes are covered. [ABSTRACT FROM AUTHOR]

Goal, Scope and Background. The environmental sustainability is one of the current priorities of the Portuguese pulp and paper industry. Life Cycle Assessment (LCA) was the methodology chosen to evaluate the sustainability of the printing and writing paper production activity. This paper grade represents about 60% of the total production of paper in Portugal and its production is expected to increase in the near future. The main goal of this study was to assess the potential environmental impacts associated with the entire life cycle of the printing and writing paper produced in Portugal from Eucalyptus globulus pulp and consumed in Germany, in order to identify the processes with the largest environmental impacts. Another goal of this study was to evaluate the effect on the potential environmental impacts of changing the market where the Portuguese printing and writing paper is consumed: German market vs. Portuguese market. Methods. The main stages considered in this study were: forestry, pulp production, paper production, paper distribution, and paper final disposal. Transports and production of chemicals, fuels and energy in the grid were also included in these stages. Whenever possible and feasible, average or typical data from industry were collected. The remaining data were obtained from the literature and specialised databases. A quantitative impact assessment was performed for five impact categories: global warming over 100 years, acidification, eutrophication, non-renewable resource depletion and photochemical oxidant formation. Results. In the German market scenario, the paper production stage was a remarkable hot spot for air emissions (non-renewable CO2, NOx and SO2) and for non-renewable energy consumption, and, consequently, for the impact categories that consider these parameters: global warming, acidification and non-renewable resource depletion. These important environmental impacts are due to the energy requirements in the printing and writing paper production process, which are fulfilled by on-site fuel oil burning and consumption of electricity from the national grid, which is mostly based on the use of fossil fuels. The pulp production stage was identified as the largest contributor to water emissions (COD and AOX) and to eutrophication. Considering that energy consumed by the pulp production processes comes from renewable fuels, this stage was also the most contributing to renewable energy consumption. Discussion. The paper distribution stage showed an important contribution to NOx emissions, which, however, did not result in a major contribution to acidification or eutrophication. The final disposal stage was the main contributor to the photochemical oxidant formation potential due to CH4 emissions from wastepaper landfilling. On the other hand, paper consumption in Portugal was environmentally more favourable than in Germany for the parameters/impact categories where the paper distribution stage has a significant contribution (non-renewable CO2, NOx, non-renewable energy consumption, acidification, eutrophication and non-renewable resource depletion) due to shorter distances needed to deliver paper to the consumers. For the remaining parameters/impact categories, the increase observed in the final disposal stage in the Portuguese market was preponderant, and resulted from the existence of significant differences in the final disposal alternatives in the analysed markets (recycling dominates in Germany, whereas landfilling dominates in Portugal). Conclusions. The pulp and paper production stages were found to be of significance for almost all of the inventory parameters as well as for the impact assessment categories. The paper distribution and the final disposal stages were only of importance for some of the inventory parameters and some of the impact categories.… [ABSTRACT FROM AUTHOR]

China has become the world largest paper and paperboard producer. However, pulp and paper industry has involved high resource consumption and severe pollution especially for water. This research has assessed the eco-efficiency of China's pulp and paper industry at the national level and provincial level. An overview regarding the cleaner production of China's pulp and paper industry was presented to reveal the measures for reducing environmental impact in the last two decades. Slacks-based measure was used to analyze the efficiency levels of 16 provinces' pulp and paper industries. To uncover the underlying causes of eco-efficiency performance, Malmquist–Luenberger index was calculated to discover the drivers of productivity growth of pulp and paper industries. Our results showed that the pollution treatment of China's pulp and paper industry has made progress in terms of water consumption and water pollution, although the absolute amount of pollution discharge is still large. Chemical oxygen demand emissions are still the first critical influencing factor of pulp and paper industry's inefficiency. Furthermore, efficiency progress was the dominating contribution of the industry's productivity growth between 2010 and 2013. The policies for adjusting the industrial structure of pulp and paper industry have resulted in the scale effects through eliminating backward production capacity and accelerating merger and acquisitions. Moreover, the productivity of pulp and paper industry was underestimated when the undesirable outputs were ignored. It indicates that the stricter environmental regulations have positive effects on paper companies to internalize environmental pressures in the production activities through environmental management. In the future, pulp and paper companies should further internalize the cost of pollution treatment through scale effects and technology improvement. [ABSTRACT FROM AUTHOR]

In accordance with environmental sustainability and in order to optimize the recycling process of prints from indirect electrophotography with liquid toner the results of investigating the effects of changes in printing conditions on the characteristics of recycled fibres is presented. Changing of printing machine conditions, respecting of voltage variations, comprises of the reverse rollers and intermediate cylinder. Based on the results it can be concluded that the change in the voltage of the reverse rollers more affect the recycling efficiency with respect to the voltage change of the intermediate cylinder. Brightness gain is higher when the print for recycling is made on uncoated paper compared to coated, and dependent on the voltage changes. Effective residual ink concentration decreases far more on handsheets obtained from recycled samples on uncoated paper in relation to both sides coated paper. Increasing the positive voltage of intermediate cylinder and increasing the negative charge of reverse rollers increases the 3 D gamut CIE L*a*b* color cubic units. Guidelines for the size of the voltage in order to obtain optimal print reproduction are provided. The further research will include the development in area of clean technologies, advanced materials, closed loop systems; therefore the significant terms in the area of environmental sustainability. [ABSTRACT FROM AUTHOR]

Abstract: The consumption of the written word is changing, as media transitions from paper products to digital alternatives. We reviewed the life cycle assessment (LCA) research literature that compared the environmental footprint of digital and paper media. To validate the role of context in influencing LCA results, we assessed LCAs that did not compare paper and print, but focused on a product or component that is part of the Information and Communication Technology (ICT) sector. Using a framework that identifies problems in LCA conduct, we assessed whether the comparative LCAs were accurate expressions of the environmental footprints of paper and print. We hypothesized that the differences between the product systems that produce paper and digital media weaken LCA's ability to compare environmental footprints. We also hypothesized that the characteristics of ICT as an industrial sector weaken LCA as an environmental assessment methodology. We found that existing comparative LCAs offered problematic comparisons of paper and digital media for two reasons — the stark material differences between ICT products and paper products, and the unique characteristics of the ICT sector. We suggested that the context of the ICT sector, best captured by the concept of “Moore's Law”, will continuously impede the ability of the LCA methodology to measure ICT products. [Copyright &y& Elsevier]

In this article, lasers in the ultraviolet, visible and infrared light spectra working with pulse widths in the nanosecond range are applied to a range of toner-paper combinations to determine their ability to remove toner. If the laser energy fluence can be chosen to stay below the ablation threshold of paper at the same time that it surpasses that of toner, paper could be cleaned and re-used instead of being recycled or disposed into a landfill. This could significantly reduce the environmental impact of paper production and use. Although there are a variety of paper conservation studies which have investigated the effects of laser radiation on blank and soiled paper, none has previously explored toner-print removal from paper by laser ablation. Colour analysis under the L a b colour space and SEM examination of the outcome indicate that it is possible to remove toner from paper without damaging and discolouring the substrate. Best results are obtained when employing visible radiation at a wavelength of 532 nm working with a pulse width of 4 ns and energy fluences under 1.6 J/cm. This means that it is technically feasible to remove toner-print for paper re-use. [ABSTRACT FROM AUTHOR]

Pulp-and-paper mills produce various types of contaminants and a significant amount of wastewater depending on the type of processes used in the plant. Since the generated wastewaters can be potentially polluting and very dangerous, they should be treated in wastewater treatment plants before being released to the environment. This paper reviews different wastewater treatment processes used in the pulp-and-paper industry and compares them with respect to their contaminant removal efficiencies and the extent of greenhouse gas (GHG) emission. It also evaluates the impact of operating parameters on the performance of different treatment processes. Two mathematical models were used to estimate GHG emission in common biological treatment processes used in the pulp-and-paper industry. Nutrient removal processes and sludge treatment are discussed and their associated GHG emissions are calculated. Although both aerobic and anaerobic biological processes are appropriate for wastewater treatment, their combination known as hybrid processes showed a better contaminant removal capacity at higher efficiencies under optimized operating conditions with reduced GHG emission and energy costs. [ABSTRACT FROM AUTHOR]

Biomaterials and new processes (3D printing and flexible hybrid electronics) offer opportunities to break free from a 2D paper world by allowing for the development of smart multi-dimensional structures. While there has been recent progress reported in each of these areas of technology, to date, the merger of these technologies has been very limited. We believe that their merger offers boundless opportunities and an opportunity for the paper industry to innovate a low cost, sustainable housing solution capable of promoting the well-being of its occupants while minimizing the environmental impact of its daily use. [ABSTRACT FROM AUTHOR]

A comparative life cycle assessment, under a cradle to gate scope, was carried out between two hand drying methods namely conventional hand dryer use and dispenser issued roll paper towel use. The inventory analysis for this study was aided by the deconstruction of a hand dryer and dispenser unit besides additional data provided by the Physical Resources department, from the product system manufacturers and information from literature. The LCA software SimaPro, supported by the ecoinvent and US-EI databases, was used towards establishing the environmental impacts associated with the lifecycle stages of both the compared product systems. The Impact 2002 + method was used for classification and characterization of these environmental impacts. An uncertainty analysis addressing key input data and assumptions made, a sensitivity analysis covering the use intensity of the product systems and a scenario analysis looking at a US based use phase for the hand dryer were also conducted. Per functional unit, which is to achieve a pair of dried hands, the dispenser product system has a greater life cycle impact than the dryer product system across three of four endpoint impact categories. The use group of lifecycle stages for the dispenser product system, which represents the cradle to gate lifecycle stages associated with the paper towels, constitutes the major portion of this impact. For the dryer product system, the use group of lifecycle stages, which essentially covers the electricity consumption during dryer operation, constitutes the major stake in the impact categories. It is evident from the results of this study that per dry, for a use phase supplied by Ontario's grid (2010 grid mix scenario) and a United States based manufacturing scenario, the use of a conventional hand dryer (rated at 1800 W and under a 30 s use intensity) has a lesser environmental impact than with using two paper towels (100% recycled content, unbleached and weighing 4 g) issued from a roll dispenser. [ABSTRACT FROM AUTHOR]

Abstract: Recent years have seen increasing demand for wider application of strategic environmental assessment (SEA), especially SEA of major policies, as a powerful instrument to safeguard the environment during the rapid industrialization and urbanization in China. Debates on SEA are concentrated on its feasibility and effective implementation in practice. This study applies Emergy analysis within the framework of social–economic–natural complex eco-system theory to overcome the limitations of methods used for assessing regional sustainability so far. This established model is tested in the case of Chinese paper industry to assess the sustainability of 5 policy scenarios. The results show that Emergy-based Indices (EbI) are more effective to measure the sustainability of industry complex ecosystem, thus EbI approach is very useful in SEAs on policy scenarios of a given complex ecosystem. [Copyright &y& Elsevier]

The article reports on the second part of the LCA studies which has been used in the pulp and paper industry. LCA is the holistic appraisal of the environmental impacts associated with a product chain. The purpose of this article is to characterize and understand the methodologies that have been used in reported LCA studies. It was found that many LCA studies fail to resolve certain elements as defined by the standard International Organization for Standardization (ISO) methodology, in the quality assessment component. According to the author, North American methodologies and databases are needed to be developed since most of the methodologies and databases used in the studies are appropriate for the European context.

The regulatory Environmental Effects Monitoring (EEM) program in Canada has found that pulp and paper mill effluents reduce the gonad size of wild fish. In such cases, there is a need for Investigation of Cause (IOC) and Investigation of Solution (IOS) studies to find the cause(s) for these responses as well as cost-effective mitigation strategies. IOC and IOS work requires the availability of practical (in terms of time and effluent volume needs) and biologically meaningful tests for assessing fish reproduction in the laboratory. One available fish reproduction test uses adult fathead minnow (Pimephales promelas) and involves a two- to three-week pre-exposure period and a three-week exposure to a test substance. Work was undertaken to determine if both the pre-exposure and effluent-exposure phases could be reduced, leading to a shorter test with a lower effluent volume requirement. For this purpose, effluent samples were taken from two thermomechanical (newsprint) pulp mills and used in tests with ..7 days of pre-exposure and 5 to 6 days of effluent exposure. Egg production was monitored in each test, and in tests with effluents from one mill, other endpoints such as gonad somatic indices and whole-body sex steroid levels, as well as vitellogenin activity in males - were measured. The shortened fish reproduction test in this study provided results similar to tests of longer duration, specifically in terms of egg production, and was able to distinguish between pulp and paper mill effluents of different potencies. The test was also found to be directly applicable for toxicity identification evaluation work as it was clearly able to distinguish between the solids and soluble fractions of a biotreated newsprint mill effluent. As such, the test is a promising tool for EEM-related IOC and IOS work. [ABSTRACT FROM AUTHOR]

Total order ranking methods are multicriteria decision making techniques used for the ranking of various alternatives on the basis of more than one criterion. The criteria, which are the standards by which the elements of the system are judged are not always in agreement, they can be conflicting, motivating the need to find an overall optimum that can deviate from the optima of one or more of the single criteria. Total order ranking methods are based on an aggregation of the criteria in a scalar function, i.e. an order or ranking index, which allow to sort elements according to its numerical value. Several evaluation methods which define a ranking parameter generating a total order ranking have been proposed in the literature. Four total order ranking methods are here described: Desirability functions, Utility functions, Dominance functions and Absolute Reference method. These methods have been compared to each other by applying them to a decision making problem in the paper industry. Various bleaching processes have been analysed and compared on the basis of multiple criteria, the aim being to find out best bleaching process among the ones proposed in the last years as alternative to chlorine bleaching process which is of high environmental impact due to the potential for chlorinated dioxin production. [ABSTRACT FROM AUTHOR]

Abstract: The significance of technical data, as well as the significance of system boundary choices, when modelling the environmental impact from recycling and incineration of waste paper has been studied by a life cycle assessment focusing on global warming potentials. The consequence of choosing a specific set of data for the reprocessing technology, the virgin paper manufacturing technology and the incineration technology, as well as the importance of the recycling rate was studied. Furthermore, the system was expanded to include forestry and to include fossil fuel energy substitution from saved biomass, in order to study the importance of the system boundary choices. For recycling, the choice of virgin paper manufacturing data is most important, but the results show that also the impacts from the reprocessing technologies fluctuate greatly. For the overall results the choice of the technology data is of importance when comparing recycling including virgin paper substitution with incineration including energy substitution. Combining an environmentally high or low performing recycling technology with an environmentally high or low performing incineration technology can give quite different results. The modelling showed that recycling of paper, from a life cycle point of view, is environmentally equal or better than incineration with energy recovery only when the recycling technology is at a high environmental performance level. However, the modelling also showed that expanding the system to include substitution of fossil fuel energy by production of energy from the saved biomass associated with recycling will give a completely different result. In this case recycling is always more beneficial than incineration, thus increased recycling is desirable. Expanding the system to include forestry was shown to have a minor effect on the results. As assessments are often performed with a set choice of data and a set recycling rate, it is questionable how useful the results from this kind of LCA are for a policy maker. The high significance of the system boundary choices stresses the importance of scientific discussion on how to best address system analysis of recycling, for paper and other recyclable materials. [Copyright &y& Elsevier]

Highlights: [•] We explore which factors affect recovery and utilization of recycled paper (RP). [•] We use panel data between 1992 and 2010 for a sample of 70 countries. [•] Both economic and demographic factors impact RP recovery and utilization. [•] Environmental awareness increases the recovery of RP in high-income countries only. [•] The motives for recycling depend on the income level of a country. [ABSTRACT FROM AUTHOR]

Abstract: Paper degradation has been studied extensively over the past few decades from both the conservation and the material science perspectives. This review focuses on the quantifiable impacts of the environment and material composition, from the viewpoint of long-term storage of historic paper-based collections. Therefore, temperature, relative humidity and their variation, and pollution are of major interest while photoinitiated processes are covered only briefly. New experiments comparing the effects of the most abundant indoor pollutants (NO2, acetic acid and formaldehyde) and the effects of fluctuating temperature and relative humidity are also presented as part of the discussion. This work highlights the need for revision of the existing dose–response (damage) functions for paper and their further development. [Copyright &y& Elsevier]

Purpose: This study aims to analyze and quantify the environmental impacts associated with the production of testliner paper using 100 % recovered paper as fiber raw material, by applying the life cycle assessment principles. A simulation of advanced sorting technology was done to prepare and use batches of raw materials with different levels of contaminants. Comparative studies of environmental impact assessment were focused on the quality of recovered paper, which is decisively influenced by the efficiency of the sorting process. The particularity of the study is that so far it is the only one that analyzes the environmental impact generated by recovered paper quality. Methods: To analyze the environmental impacts in the scenarios, life cycle assessment methodology was considered. Potential environmental impacts were assessed by using the CML , Dec.07 method developed by the Centre for Environmental Science from the University of Leiden. Results and discussion: In this study, acidification potential, abiotic resources depletion potential, eutrophication potential, global warming potential, photochemical ozone creation potential, and human toxicity potential were the impact categories analyzed. Considering that the system boundaries refer only to the paper mill that was obtained, all unitary processes involved in the manufacturing of product system influence in varying proportions the impact categories chosen for evaluation. A higher concentration of contaminants leads to a higher amount of energy and water used, and thus, a significant amount of waste and emissions generated. Simulations performed have highlighted the importance of sorting technology that influences the quality of raw material that will be used. Conclusions: Utilization of recovered paper batches with a low quality contributes to an increased environmental impact associated with the testliner paper manufacturing stage. A low quality of recovered paper will influence energy consumption in different modules of the system (recycled fiber pulp preparation, paper machine, and wastewater treatment), the volume of waste generated, and consequently the emissions released both in air and water. [ABSTRACT FROM AUTHOR]

Abstract: The efficiency of several lab scale treatments (aerobic, anaerobic and ozone or combination of these) was evaluated using two packaging board mill whitewaters. The effect of the different treatments on the elimination of the organic load, the chemical oxygen demand (COD) and the toxicity was tested as well as the relationship between these parameters. Biocides, phenolic compounds, surfactants, plasticiziers and wood extractives were identified in untreated and treated whitewaters by liquid chromatography coupled with mass spectrometry (LC–MS) or gas chromatography coupled with mass spectrometry (GC–MS). A strong dependency on the water type and treatment efficiency was observed, being the combination of anaerobic and aerobic treatments the best option to reduce the organic contaminants in these waters, although in some cases, the toxicity did not decrease. However, ozone as post-treatment permitted a further reduction of organic compounds, toxicity and COD. [Copyright &y& Elsevier]

Animals can influence their social environment by preferentially associating with certain conspecifics. Such preferential association has gained increasing theoretical attention, as it may influence social evolution and population dynamics. However, relatively little empirical work has examined the occurrence of preferential association and its effects on cooperative group formation. Here, we test the factors associated with cooperative group formation in Polistes dominulus nest-founding queen wasps. P. dominulus are a good system to study preferential association, as foundresses can nest alone or in groups and group membership is flexible. We found that both social and environmental factors were associated with partner choice. First, facial patterns were associated with cooperation. Wasps with more similar facial patterns were more likely to cooperate than wasps with less similar facial patterns. This preferential phenotypic association fits the theoretical criteria for the evolution of tag-based cooperation. Season was also associated with cooperation; wasps on early-season nests were more likely to cooperate than wasps on late-season nests. High levels of aggression by nest owners during initial interactions were also correlated with lower probabilities of subsequent cooperation, suggesting that nest owners have some control over group membership. Other factors including body weight, weight similarity and nest productivity were not linked with cooperation. Overall, multiple factors influence cooperation in paper wasps, including facial pattern similarity. The occurrence of preferential phenotypic association in paper wasps is quite interesting and may influence the evolution of cooperation and population divergence in this group. [ABSTRACT FROM AUTHOR]

Pyrolysis volatiles and the environmental impact of printing paper in an air atmosphere were investigated using pyrolysis-gas chromatography/mass spectrometry and scanning electron microscopy. CO and light-pollution products were found to be the major products from pyrolysis volatiles; furthermore, because oxygen participates in the chemical reaction, many of the pyrolysis volatiles emitted during the paper printing process were different from those formed under an N atmosphere. Although a small number of the volatiles were moderately toxic products, the concentrations of these volatiles were low. Heat-induced inkless eco-printing (HIEP) was found to take less time than the pyrolysis experiment in this paper and thus resulted in fewer pyrolysis volatiles. Thus, fewer pyrolysis volatiles will be emitted within the practical temperature range; in particular, no carcinogens were emitted in the pyrolysis temperature range of 250-700 °C. Therefore, HIEP was found to be an ecologically and environmentally preferable technology. [ABSTRACT FROM AUTHOR]

This study assesses the policy/legal status of both multistream residues and potential secondary products ('symbiosis products') and whether there could be environmental benefits associated with the utilization of residues from integrated pulp and paper and carbon steel mills as raw materials for such secondary products. Waste-related European Union (EU) and Finnish policy and legal instruments were reviewed to identify potential constraints for, and suggested next steps in, the development of potential process industry residue-based symbiosis products. The products were soil amendment pellets, low-grade concrete, and mine filler. A global warming potential (GWP) assessment and an exergy analysis were applied to these potential symbiosis products. Some indicative GWP calculations of greenhouse gas emissions associating similar and/or analogous products based on virgin primary raw materials, more energy-intensive processes, and the alternative treatment of these residues as wastes are also presented. This study addresses GWP, exergy, and legal aspects in a holistic manner to determine the potential environmental benefits of secondary products within the EU legal framework. The GWP assessment and exergy analysis indicate that the utilization of multistream residues causes very low environmental burdens in terms of GWP. The utilization option can have potential environmental benefits in terms of GWP through process replacement and avoided landfilling and waste treatment impacts, as well as potentially through emission reductions from product replacement if suitable and safe applications can be identified. Waste regulation does not define the legal requirements under which utilizing residues in such novel concepts as introduced in this study would be possible, nor how waste status could be removed and product-based legislation be applied to the potential products instead. [ABSTRACT FROM AUTHOR]

Abstract: This study uses Life Cycle Assessment (LCA) to assess the environmental profiles and greenhouse gas (GHG) emissions for bioethanol production from waste papers and to compare them with the alternative waste management options of recycling or incineration with energy recovery. Bioethanol production scenarios both with and without pre-treatments were conducted. It was found that an oxidative lime pre-treatment reduced GHG emissions and overall environmental burdens for a newspaper-to-bioethanol process whereas a dilute acid pre-treatment raised GHG emissions and overall environmental impacts for an office paper-to-bioethanol process. In the comparison of bioethanol production systems with alternative management of waste papers by different technologies, it was found that the environmental profiles of each system vary significantly and this variation affects the outcomes of the specific comparisons made. Overall, a number of configurations of bioethanol production from waste papers offer environmentally favourable or neutral profiles when compared with recycling or incineration. [Copyright &y& Elsevier]

The molded pulp, a product of three-dimensional papermaking technology, is environmentally friendly and has a low environmental impact due to its ability to decompose quickly in the natural environment after disposal. The application of molded pulp for food packaging can replace or reduce the use of plastic food packaging. Researchers extract fibers from plants for the production of safe and hygienic molded pulp for food packaging, and they also study and enhance the qualities of molded pulp to broaden its use in the food industry. This paper reviews the sources and varieties of plant fiber used in molded pulp for food packaging, as well as research on the improvement and optimization of the performance of molded pulp products. Additionally, issues with molded pulp's actual use for food packaging are reviewed, along with the potential for future research. This work can serve as a reference for molded pulp applications and research in the food industry in the future. [ABSTRACT FROM AUTHOR]

The impacts of environmental pollution are potentially irreversible and have become a major concern for society. Faced with this reality, the purpose of this study is to identify what type of flexible packaging material used in the food industry creates less pollution. The Leopold Matrix was employed to quantitatively assess the life cycle of plastic and paper packaging, using information from various scientific articles and peer-reviewed indexed journals. The interactions between physical, biological, and socioeconomic elements were established for each action in the life cycle of the packages. The results showed that flexible plastic packaging pollutes 16 percent more in the physical aspect concerning soil and water pollution than paper packaging, which has a more significant impact on air pollution. Regarding the biological aspect, plastic pollutes 63 percent more than paper in terms of damage to flora and fauna. Finally, on the socioeconomic level, paper poses a greater health risk for human beings owing to the emission of gases in its production, whereas plastic packages contribute more to the economy for being an extensive industry. [ABSTRACT FROM AUTHOR]

The action required to stem the environmental and social implications of climate change depends crucially on how humankind shapes technology, economy, lifestyle and policy. With transport CO2 emissions accounting for about a quarter of the total, we examine the contribution of CO2 output by scientific travel. Thankfully for the reputation of the scientific community, CO2 emissions associated with the trips required to present a paper at a scientific conference account for just 0.003% of the yearly total. However, with CO2 emissions for a single conference trip amounting to 7% of an average individual’s total CO2 emissions, scientists should lead by example by demonstrating leadership in addressing the issue. [ABSTRACT FROM AUTHOR]

We conduct a comparative life cycle assessment of two business card options: a smartphone software and the common paper- based alternative. Life cycle impacts of production, distribution and use of business cards were compared and contrasted for both systems. Given the prevalence and multifunctionality of digital devices and services, we analyze the environmental impacts of the two systems and evaluate their total energy consumption, Greenhouse Gas (GHG) emissions and toxic releases by conducting a two-stage life cycle assessment with alternating functional units. The results indicate that, for a small-scale functional unit, the paper-based business card system causes slightly less environmental impact and has lower energy demand than the software-based (digital) business card system. Whereas when considering the more likely, large scale (real world scenario) functional unit, the digital business card system is more environmentally friendly and economical in terms of energy consumption. By comparing these two systems, this paper serves businesses and consumers when considering environmental consequences and energy depletion of their business networking options. [ABSTRACT FROM AUTHOR]

The effectiveness of Asarum sieboldii extracts as an environmental-friendly fumigant to mitigate the aging of Korean paper cultural heritage made of traditional paper called Hanji was examined. As results, antimicrobial activity of A . sieboldii extracts against Aspergillus versicolor on Hanji is observed at the concentration exceeding 25 mg. As the short-term change of Hanji property right after treatment of A . sieboldii extracts exceeding 25 mg, it is observed that the physical and optical properties of initial Hanji decreased with the increases of the extracts concentration. In terms of the long-term change by artificial aging test, however, the aging rate of Hanji samples treated by A . sieboldii extracts is similar to that of non-treated Hanji samples. It means that A . sieboldii extracts do not degrade the stability of Hanji property. Overall, these results demonstrate that A . sieboldii extracts may have the potential as a fumigant to the Korean paper cultural heritage due to their antimicrobial effectiveness and long-term permanence. [ABSTRACT FROM AUTHOR]

LCA studies on waste management have been promoted as they can help policy makers choose the best environmental options. However, the increasing globalization of raw materials and waste makes the optimization of waste management strategies and policies quite challenging. Therefore, new approaches are needed in order to identify the consequences of markets on the waste management systems. This paper concentrates on the quantification of greenhouse gas (GHG) emissions of recycling processes. The aim is to generate a comprehensive assessment of GHG emissions as a consequence of increasing the amount of material collected for recycling. Consequential life cycle assessment (CLCA) is an effective methodological framework for addressing GHG quantifications within market, but to properly perform and assess all of the market links between raw materials and waste, it is necessary to determine the cause-effect chains made up of physical flows. Thus, we propose integrating the methodologies of material flow analysis (MFA) and CLCA. We applied these methodologies to the paper and cardboard recycling system in Spain. The GHG results varied between −36 kg CO 2 eq. and −317 kg CO 2 eq. per ton of waste paper collected, depending on the quantity of waste paper exported and the source of marginal pulp considered. The cumulative energy demand (CED) was also calculated as complementary indicator. Similar trends as for GHG emissions were obtained. The future GHG quantifications should be based on the flows described by MFA analysis and should be quantified using CLCA because methodologies that accurately account for GHG are necessary for decision-making. [ABSTRACT FROM AUTHOR]

Entered into force in 2011, the Protocol on Integrated Coastal Zone Management (ICZM) in the Mediterranean is a major innovation in that it is the first supra-State legal instrument aimed at coastal zone management. However, the nature and magnitude of change it is actually generating, or is likely to generate, in domestic coastal zones management systems, are highly uncertain. Investigating such prospects for change in contrasted contexts around the Mediterranean, and therefore providing a critical view of the Protocol as a game-changer, is the aim of this article. Results call for vigilance: the risk is real that the Protocol will not change much and that it will become a paper-protocol only. Ratifying it is – relatively – easy. Avoiding “ratifications of convenience” is more demanding. For various reasons the Protocol is likely to have mostly limited impacts on domestic coastal law development. It probably has more potential in terms of influencing changes in governance processes and increasing the social demand for ICZM. But this potential may only be translated into facts under stringent conditions on political will and good faith from Parties to adopt an ambitious understanding of the Protocol, and on appropriation by civil societies around the Mediterranean. [ABSTRACT FROM AUTHOR]

There are thousands of pulp and paper mills worldwide. The utilization of the waste they produce is a problem of particular importance. Many methods have already been put forward for the management of the mixture of lime mud and cellulose fibre residues. The chemical nature of its management presents a challenge because it requires costly catalysts and long retention times or raises criticisms about its environmental impacts. Several techno-economic analyses (including various modifications to anaerobic fermentation; combustion; pyrolysis and composting) have been carried out on an almost commercial scale to holistically assess the wide portfolio of management issues. The data obtained indicate that it cannot be clearly concluded that one particular method is the best for dealing with all management issues. However, the conclusions do provide an insight into how processing technologies can be adapted in specific cases. [ABSTRACT FROM AUTHOR]

Pyrolysis volatiles and the environmental impact of printing paper, newspaper, and silk were investigated to identify suitable materials for heat-induced eco-printing (HIEP) using pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). Furthermore, the printing effects of simulated HIEP and the material microstructures were studied using scanning electron microscopy (SEM). The results indicated that the toxicity of pyrolysis volatiles is highest for newspaper, followed by silk and then printing paper, whereas environmental friendliness follows the opposite trend. A high concentration of lignin, the basic structural element of which is phenyl propane, and the presence of halogens in the newspaper led to the generation of more toxic substances during the pyrolysis process. The benzene compounds and heterocyclic compounds in silk also produced high levels of toxic substances. Based on these findings and the higher color permeability of newspaper, printing paper was the most suitable material for HIEP and newspaper was the least suitable. Additionally, silk may still be used in HIEP in small amounts for the production of art, name cards, and clothing tags. [ABSTRACT FROM PUBLISHER]

This study investigated the compliance of paper-making plants in Phong Khe Commune of Bac Ninh Province with regulations on wastewater management. According to existing regulations for wastewater management, all paper plants in Bac Ninh province are required to submit an environmental impact assessment report, pay the wastewater charges, and establish a wastewater treatment system. Many paper-making plants in the commune did not, however, comply with these regulations. Although fines were imposed for non-compliance, only a few plants paid the fines due to weak enforcement. As a result, the current costs of compliance of paper-making plants were very small compared with the full costs of compliance. Type of plant, location of the plant, and number of schooling years of the plant owners were found to be significant factors affecting compliance. The main reasons why the plants did not comply with the regulations were the plant owners' inadequate understanding of environmental regulations, their lack of financial resources, limited space for treatment system installation, small fines, and the limited capacity of the local environment authorities in enforcing the regulations . The option of wastewater treatment for a group of paper-making plants located close to one another was widely accepted. The study proposes collective action for the adoption of this treatment option and policy recommendations. [ABSTRACT FROM AUTHOR]

The paper proposes a methodology for rapid assessment of energy efficiency and of its impact on energy costs and on environment. Indicators of energy efficient and of environmental impact assessment are proposed. As a numerical example, we present a case study for a pulp and paper mill. Such methodology is very useful for departments tracking energy consumption and for decision staff from paper mills. [ABSTRACT FROM AUTHOR]

The article presents a study on the viability of using aqueous solutions of sodium percarbonate as a new method for bleaching discolored paper. Appositely prepared oxidized papers and authentic discolored papers were analyzed to examine the advantages and drawbacks of sodium percarbonate treatments. Results suggest that sodium percarbonate solutions can be a valid substitute to hydrogen peroxide solutions in brightening discolored mechanical pulp papers because it is more stable when stored, safe to use and has low environmental impact.

Abstract: Various international treaty bodies and non-governmental organisations continuously urge States to establish a network of Marine Protected Areas (MPAs) in areas beyond the limits of national jurisdiction (ABNJ). Although this goal is far from being reached, the OSPAR Convention may serve as an example illustrating the efforts made on a regional level for the North-East Atlantic. However, these efforts to effectively protect the marine environment are subject to limitations under the Convention on the Law of the Sea (UNCLOS). Likewise, the OSPAR Convention itself restricts the scope of such protected areas. The OSPAR Convention does not adequately cover all human uses of the oceans that may interfere with a protected area, and it lacks opportunities for internationalised enforcement measures. Consequently, the responsibility for effective conservation measures under the OSPAR model ultimately remains with individual Contracting Parties, i.e. their commitment to set stricter standards and to agree on their enforcement. Nevertheless, ‘soft’ obligations such as reporting duties are suitable for collecting data on the need for protection and utilisation of the MPAs. Additionally, cooperation with regional fisheries management bodies allows for better protection of the living resources in these areas. Finally, OSPAR MPAs can draw attention to particularly vulnerable ecosystems and promote conservation standards and measures such as those developed under the auspices of the FAO. [Copyright &y& Elsevier]

This paper presents the study of the feasibility of incorporating lignocellulosic nanofibers (LCNF) to paper in order to maintain the relevant physical properties and increase the number of cycles that paper can be recycled in the technosphere in a more circular economy. For that purpose, the effect of mechanical refining in recycling processes was compared with that of the novel LCNF addition. In this sense, the behavior of a bleached kraft hardwood pulp when recycled was investigated, as well as the effects of each methodology. Since there are many issues to be considered when trying to replace a technology, the present paper analyses its feasibility from a technical and environmental point of view. Technically, LCNF present greater advantages against mechanical refining, such as higher mechanical properties and longer durability of the fibers. A preliminary life cycle assessment showed that the environmental impacts of both systems are very similar; however, changing the boundary conditions to some feasible future scenarios, led to demonstrate that the CNF technology may improve significantly those impacts. [ABSTRACT FROM AUTHOR]

Abstract: For most materials used to provide buildings, infrastructure, equipment and products, global stocks are still sufficient to meet anticipated demand, but the environmental impacts of materials production and processing, particularly those related to energy, are rapidly becoming critical. These impacts can be ameliorated to some extent by the ongoing pursuit of efficiencies within existing processes, but demand is anticipated to double in the next 40 years, and this will lead to an unacceptable increase in overall impacts unless the total requirement for material production and processing is reduced. This is the goal of material efficiency, and this paper aims to stimulate interest in the area. Four major strategies for reducing material demand through material efficiency are discussed: longer-lasting products; modularisation and remanufacturing; component re-use; designing products with less material. In industrialised nations, these strategies have had little attention, because of economic, regulatory and social barriers, which are each examined. However, evidence from waste management and the pursuit of energy efficiency suggests that these barriers might be overcome, and an outline of potential mechanisms for change is given. In bringing together insights into material efficiency from a wide range of disciplines, the paper presents a set of 20 open questions for future work. [Copyright &y& Elsevier]

Abstract: Viable alternatives to conventional newspapers, such as electronic papers, e-papers or e-readers, are intended to have many of the qualities of paper, such as reading using reflective light, high resolution, 180° viewing angle. It has been suggested that the environmental impact of e-paper can be lower than for printed and internet-based newspapers. However, in order to find the facts of the matter, a thorough life cycle perspective covering raw material acquisition, production, use and disposal should preferably be used to study the environmental performance of the different products. A screening life cycle assessment was performed to describe the potential environmental impacts of two product systems; printed on paper and tablet e-paper newspapers. Results show that the most significant phase of the life cycle for both product systems was the production of substrate or platform. Accordingly, key aspects that may affect the resulting environmental performance of newspaper product systems were for the printed newspaper number of readers per copy and number of pages per issue and for the tablet e-paper newspaper lifetime and multi-use of the device. The printed newspaper in general had a higher energy use, higher emissions of gases contributing to climate change and several other impact categories than the tablet e-paper newspaper. It was concluded that tablet e-paper has the potential to decrease the environmental impact of newspaper consumption. However, further studies regarding the environmental impact of production and waste management of electronic devices and internet use, as well as more comprehensive assessment of toxicological impacts are needed. As the data on the electronic devices becomes more comprehensive this may prove to be a major limitation of electronic newspaper systems. Developers are suggested to strive towards minimisation of toxic and rare substances in production. [Copyright &y& Elsevier]

Aim: The purpose of this work was to study the feasibility of producing economic flame retardant bacterial cellulose (BC) and evaluating its behaviour in paper production. Methods and Results: This type of BC was prepared by Gluconacetobacter subsp . xylinus and substituting the glucose in the cultivation medium by glucose phosphate as a carbon source; as well as using corn steep liquor as a nitrogen source. The investigated processing technique did not dispose any toxic chemicals that pollute the surroundings or cause unacceptable effluents, making the process environmentally safe. The fire retardant behaviour of the investigated BC has been studied by non-isothermal thermogravimetric analysis (TGA & DTGA). The activation energy of each degradation stage and the order of degradation were estimated using the Coats–Redfern equation and the least square method. Strength, optical properties, and thermogravimetric analysis of BC-phosphate added paper sheets were also tested. Conclusions: The study confirmed that the use of glucose phosphate along with glucose was significant in the high yield production of phosphate containing bacterial cellulose (PCBC1); more so than the use of glucose phosphate alone (PCBC2). Incorporating 5% of the PCBC with wood pulp during paper sheet formation was found to significantly improve kaolin retention, strength, and fire resistance properties as compared to paper sheets produced from incorporating bacterial cellulose (BC). Significance and Impact of the Study: This modified BC is a valuable product for the preparation of specialized paper, in addition to its function as a fillers aid. [ABSTRACT FROM AUTHOR]

Abstract: Two experiments using rainbow trout (Oncorhynchus mykiss) were conducted to examine the combined effects of energy intake as manipulated by ration and pulp and paper mill effluent exposure over either one, or two consecutive reproductive cycles. This study demonstrated that the level of energy intake affected the full range of measured parameters from energy allocation to somatic growth and the gonadal development, steroid production and hematology. Increasing ration level expectedly increased growth, condition, liver and gonad size. Female trout in the higher ration treatments produced more follicles and had larger eggs, investing the same relative proportion of total energy into ovarian development. Sex steroid levels and hematological parameters were also positively influenced by increasing ration level in males and females. By far, the most dramatic impact of reduced ration on reproduction was to substantially reduce the frequency of sexually maturing fish. The effects of effluent exposure were not as marked as those linked to ration level and typically did not manifest unless fish were exposed through two consecutive reproductive cycles. The physiological effects of pulp and paper effluent exposure observed in these experiments were not consistent between the two experiments conducted herein, nor were they consistent with previously observed impacts in similar experiments with this effluent. Effluent exposure over one reproductive cycle did not impact physiological parameters in trout. However, when effluent exposure was maintained over two reproductive cycles, a new pattern of effluent response emerged including increased condition factor in both sexes, a decrease in the potential ability of the blood of females to transport oxygen, and increased sex steroids and reproductive investment in males. Effluent was also observed to cause reduced growth in male trout over two years. The effects of ration on gonad and liver size were far more obvious and consistent when a longer exposure was employed, thus, it appears to take more than one full year for energy intake changes to be reflected in those particular physiological endpoints. [Copyright &y& Elsevier]

Background, aim, and scope North American pulp and paper mills are facing tremendous challenges, which may necessitate major mill modernizations. An example is process modification to reduce dependency on purchased power, which is an expensive resource. Such modifications may have environmental implications at the mills' sites, on their product life cycle, and on other interconnected systems, and therefore, systematic tools such as life cycle assessment (LCA) need to be applied. Different LCA system boundary approaches can be used for such process design applications, and these approaches need to be compared to determine their respective benefits and limitations in this context. This study compares setting the system boundary according to a cradle-to-gate approach [attributional LCA (ALCA)] and a system expansion [consequential LCA (CLCA)] approach using a case study, which deals with implementing cogeneration and increased de-inked pulp production at an integrated newsprint mill. Methodology A case study considering various process options to reduce purchased electricity at an integrated newsprint mill is defined. These options include implementing cogeneration and increasing de-inked pulp production. The environmental impacts related to these process options are analyzed using two LCA methodologies. The first one consists in setting the system boundary according to a cradle-to-gate ALCA approach, while the second one uses a differential CLCA approach (system expansion). Comparisons of the two methods are based on different parameters: inclusion/exclusion of the indirect environmental consequences, selected allocation procedures, and effect of using the average versus the marginal technology for power production. Results Both the ALCA approach and the CLCA approach indicate that the process options are beneficial. However, the results show that indirect environmental consequences, which are assessed only with the CLCA approach, can be opposite to direct effects (e.g., the results can indicate an improvement of the direct impacts and a deterioration of the indirect ones). In addition, environmental impacts obtained by modeling the average or the marginal technology may be very different. Using an ALCA approach often necessitates the use of an arbitrary allocation procedure, which can greatly affect the results. On the other hand, ALCA can be used to perform "hot spots" identification, which, at this time, is not possible with CLCA. Discussion The cradle-to-gate boundary approach, which is usually used in the literature for pulp and paper process design applications, may not always be the most appropriate to determine the environmental consequences of implementing different process options. However, at this time, there is no method based on CLCA allowing for "hot spots" identification, and thus, a combined approach may be required for process design. Conclusions It is shown that the choice of the system boundary can significantly affect the results. More specifically, the usage of different allocation procedures in ALCA leads to different interpretation of the results, which does not occur when using the CLCA approach. CLCA provides more complete information for decision making for the cases where most of the consequences occur outside the life cycle of the product investigated. Recommendations and perspectives Research opportunities include developing methodologies to integrate ALCA and CLCA for improved process design applications and mechanisms for reducing uncertainty in CLCA. [ABSTRACT FROM AUTHOR]