Search

Impurities are inevitable in crude glycerol, a by-product of biodiesel, which has a great influence on aqueous phase reforming (APR). This work investigates three impurities (CH 3 OH, CH 3 COOH, and KOH) in the aqueous phase reforming of glycerol (GAPR) using a mesoporous Ni–Cu/CeO 2 catalyst at three temperatures. The experiment results indicate that the increase of temperature is beneficial to the conversion of glycerol into gas products, but not favor to the proportion of H 2 in the gas phase. The presence of CH 3 OH almost has not affected the total gas volume, while CH 3 COOH and KOH decreased and increased the gas volume, respectively. The deactivation of the catalyst occurs under acidic conditions because the active phase Ni on the catalyst surface is lost in the hydrogen evolution reaction. KOH has the greatest influence on the gas phase composition, which greatly increases the H 2 production and the proportion of H 2. The results of liquid-phase solution analysis show that the addition of CH 3 COOH promoted the dehydration of glycerol, which is contrary to the results obtained by adding KOH. CH 3 OH, as the final product of glycerol dehydrogenation and decarbonization, is added to the initial solution, which will be conducive to the dehydration reaction. The addition of CaO can increase the H 2 production in the APR of glycerol solution containing impurities. • Mesoporous Ni–Cu/CeO 2 was successfully synthesized to APR of glycerol. • Effects of impurities of CH 3 OH, CH 3 COOH, and KOH on APR of glycerol were determined. • CH 3 COOH and KOH decreased and increased gas production from APR, respectively. • Deactivation of Mesoporous Ni–Cu/CeO 2 in APR occurred under acidic conditions. • Enhanced WGS and reduced methanation were achieved by in-situ CO 2 removal. [ABSTRACT FROM AUTHOR]

Hydrogen production from sorption enhanced aqueous phase reforming (APR) of biodiesel byproduct glycerol was studied by Ni-based monometallic and bimetallic catalysts supported on gelatinous MgO supports. Compared with Ni-based monometallic catalyst, the H 2 selectivity and glycerol conversion of the Cu–Ni bimetallic catalyst were found to be increased more than 3% and 30%, respectively. Meanwhile, higher reaction temperature was found to have higher H 2 yield with lower H 2 selectivity. The H 2 yield using the catalyst with gelatinous MgO support was 1.25 times higher than that of calcined support. Through in-situ CO 2 capture, the addition of CaO to the Cu–Ni bimetallic catalyst increased more than 58.3% and 14.4% of the H 2 yield and selectivity, respectively. An analysis about liquid product component indicate that the presence of CaO promote the further cleavage of the C–C bond, which further increased the conversion of glycerol. Furthermore, it was found that the presence of CaO could also improve the stability of the catalyst through the control experiments. [Display omitted] • Sorption enhanced APR to H 2 with in-situ CO 2 capture was studied. • Monometallic and bimetallic supported on MgO were developed. • Cu–Ni supported on gelatinous MgO exhibited good APR performance. • H2 yield by gelatinous MgO support was 1.25 times higher than that of calcined MgO. • Presence of CaO in APR improved conversion, selectivity, and stability. [ABSTRACT FROM AUTHOR]

This paper describes the synthesis of a series of Ni based Al-MCM-41 oxygen carriers with and without Ce promoter and their application in chemical looping steam reforming of glycerol. The Al-MCM-41 is derived from montmorillonite. The oxygen carriers were prepared by direct-synthesis and post-synthesis method. A variety of technologies including N 2 adsorption-desorption, X-ray diffraction (XRD), inductively coupled plasma optical emission spectroscopy (ICP-OES), H 2 temperature-programmed reduction (H 2 -TPR), and transmission electron microscopy (TEM) were conducted to characterize the fresh and used oxygen carriers. The results show the direct-synthesis oxygen carrier possesses excellent textual properties, such as high Ni loading, small particle size, large pore volume, and uniform pore size. The incorporation of Ce could effectively control particle size via strong metal support interaction, promote the homogeneous distribution of Ni, and enhance oxygen mobility capability and water gas shift reaction. And thus shorten ‘dead time’ during the fuel feed step. The CeNi/Al-MCM-41 displayed the superior activity and excellent long-term stability, which could be due to the strengthened anti-sintering and coke capability. [ABSTRACT FROM AUTHOR]

For the fixed-bed reactor configuration in the sorption-enhanced steam reforming process (SERP), solid mixture of catalyst and sorbent is stationary and alternatively exposed to reaction and regeneration conditions for multi-cycles by periodically switching the feed gases for enhanced hydrogen production with in-situ CO 2 removal. A NiO/NiAl 2 O 4 catalyst was synthesized by the co-precipitation method with rising pH technique and the crystalline spinel phase of NiAl 2 O 4 was formed under the calcination temperature of 900 °C. The catalyst was characterized by X-ray powder diffraction (XRD), scanning electron microscope (SEM), thermo-gravimetric analysis (TGA), and N 2 adsorption–desorption. The non-stoichiometric thermodynamic calculation was carried out to determine the effects of temperature and in-situ CO 2 removal on the enhancement of hydrogen production by SERP from glycerol at 425–700 °C. The multi-cycles on reaction and regeneration for hydrogen production by SERP from glycerol were performed by NiO/NiAl 2 O 4 catalyst and CaO based sorbent in a fixed-bed reactor. The results showed that hydrogen production by SERP can be clearly divided into three periods, and the experimental gaseous products were compared with non-stoichiometric thermodynamic calculations. It is obvious that H 2 purity was greatly increased, and CO 2 , CO and CH 4 concentrations were reduced by in-situ CO 2 removal during the pre-breakthrough period. It is found that enhanced hydrogen production was mainly depended on in-situ CO 2 removal. The operation durations for producing high-purity hydrogen of more than 90% were decreased with the increase of the cycles. It may due to the decrease in the reactivity of CaO based sorbent after multi-cycles reaction and regeneration. [ABSTRACT FROM AUTHOR]

Hydrogen production from chemical looping steam reforming (CLSR) of glycerol was studied by Ni-based oxygen carrier in a fixed-bed reactor. For the fixed-bed reactor configuration, solid Ni-based oxygen carrier is stationary and alternatively exposed to reducing and oxidizing conditions by periodically switching the feed gases. The Ni-based oxygen carrier was prepared by a liquid-state co-precipitation method with rising pH technique and the characterization was performed by X-ray powder diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and N 2 adsorption–desorption. Gaseous products and temperature variety during CLSR process by Ni-based oxygen carrier in a fixed-bed reactor were measured, and the thermodynamic equilibrium calculation was also carried out. The results showed that the Ni-based oxygen carrier synthesized has a dual function and can efficiently convert glycerol and steam to H 2 by redox reactions. The coexisting reactions of glycerol oxidization (or NiO reduction) and steam reforming occurred before the steady stage of hydrogen production in the fuel feed step, and the conversion of NiO to Ni was obtained. Alternating reduction and oxidation reactions enabled Ni-based oxygen carrier to produce H 2 with a concentration of 85% of the equilibrium value at 600 °C, and glycerol conversion was up to 99%. The increase of temperature related to the exothermic reactions by Ni-based oxygen carrier in CLSR process was observed in redox cycles. [ABSTRACT FROM AUTHOR]

The Ni-based multifunctional catalysts for the sorption-enhanced steam reforming process (SERP) with simultaneous in-situ CO 2 removal were synthesized by the co-precipitation method with rising pH technique, and the crystalline spinel phases of NiAl 2 O 4 and MgAl 2 O 4 in the catalysts were formed under the calcination temperature of 900 °C. The catalysts were characterized by X-ray powder diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), thermo-gravimetric analysis (TGA), and N 2 adsorption-desorption. Nonisothermal and isothermal CO 2 sorption experiments were carried out to evaluate the activity of catalysts for CO 2 removal. Desorption and optimum sorption temperatures for CO 2 removal were determined. Hydrogen production from SERP of glycerol over the multifunctional catalysts has been experimentally evaluated under 550 °C and steam to carbon (S/C) ratio of 3. The multifunctional catalyst with the composition of 41.21 wt% NiO, 28.02 wt% Al 2 O 3 and 30.77 wt% CaO presented satisfactory hydrogen purity in the multi-cycles of reforming and regeneration processes. Enhanced hydrogen production was mainly depended on in-situ CO 2 removal, and the operation durations for producing high purity hydrogen in the initial 30 min were relatively stable. The multifunctional catalyst possesses uniform distribution of Ni, Ca and Al, contributing significantly to the excellent CO 2 sorbent capacity and reforming activity. This multifunctional catalyst synthesized offers a new scheme other than the conventional mixture of sorbent and catalyst for SERP. [ABSTRACT FROM AUTHOR]

In this study, renewable hydrogen production was achieved by coupling of water splitting and glycerol oxidation reforming by chemical looping technology (CLWS-GOR) using the novel Ce–Ni modified Fe-based oxygen carriers (OCs). The OCs were developed by combining metal chelating sol-gel and isometric impregnation method, which exhibited anti-sintering characteristic and lattice oxygen migration ability in CLWS-GOR. The amount of hydrogen between 12.49 and 12.96 mmol in the steam stage was produced from all the OCs with different ratios of Fe, Ce and Ni. However, with the increase of Ce and Ni doping, the production of H 2 and CO in the fuel stage increased, as well as the probability of carbon deposits released in the subsequent steam stage. The H 2 /CO ratio in syngas were easily adjusted by steam to carbon molar ratio (S/C) in chemical looping steam reforming (CLSR), but the effects of steam introducing led to gradual deterioration of OCs. The results proved the OCs prepared by the combination method has high activity and stability for renewable hydrogen production from coupling of CLWS-GOR. [Display omitted] • Coupling of water splitting and glycerol oxidation reforming by chemical looping. • Ce–Ni modified Fe-based OCs were synthesized by combined method. • Pure H 2 was achieved from CLWS-GOR by reduced OCs. • WGS enhancement and the H 2 /CO ratio adjustment were achieved. [ABSTRACT FROM AUTHOR]

Highlights: [•] Ni–Cu–Al catalyst for hydrogen production was synthesized by rising pH technique. [•] Experimental data were analyzed with non-stoichiometric thermodynamic calculation. [•] Catalyst deactivation due to carbon deposits in glycerol steam reforming was found. [•] Carbon removal was analyzed by TGA experiment during medium temperature oxidation. [•] Reforming was tested by separability kinetics of rate law and catalyst deactivation. [Copyright &y& Elsevier]

Abstract: The objective of this review is to analyze potential technologies and their baseline performance of producing hydrogen from catalytic steam reforming of biodiesel byproduct glycerol. High oxygen content and high impurity level of biodiesel byproduct glycerol, as well as the complex intermediates and high coking potential in its thermal degradation, make the modeling, design, and operation of glycerol steam reforming a challenge. Thermal decomposition characterization of biodiesel byproduct glycerol was covered, and the recent developments and methods for high-purity hydrogen production from glycerol steam reforming were illustrated. The thermodynamics constraint of water gas shift reaction can be overcome by the sorption-enhanced steam reforming process, which integrated catalytic steam reforming, water gas shift reaction and in-situ CO2 removal at high temperatures in a single stage reactor. The effectiveness of both the enhanced H2 production and the use of CO2 sorbents have been demonstrated and discussed. The technical challenges to achieve a stable high-purity hydrogen production by the sorption-enhanced steam reforming process included extending operation time, selecting suitable sorbents, finding a way for continuous reaction-regeneration of catalyst and sorbent mixture and improving process efficiencies. The continuous sorption-enhanced steam reforming of glycerol was designed by a simultaneous flow concept of catalyst and sorbent for continuous reaction-regeneration using two slow moving-bed reactors for high-purity hydrogen production and CO2 capture, and in this process, catalyst and sorbent were run in nearly fresh state for H2 production. The sorption-enhanced chemical-looping reforming was also demonstrated. The paper discusses some issues and challenges, along with the possible solutions in order to help in efficient production of hydrogen from catalytic steam reforming of biodiesel byproduct glycerol. [Copyright &y& Elsevier]

In this study, the continuous sorption-enhanced steam reforming of glycerol to high-purity hydrogen production by a simultaneous flow concept of catalyst and sorbent for reaction and regeneration using two moving-bed reactors has been evaluated experimentally. A Ni-based catalyst (NiO/NiAl2O4) and a lime sorbent (CaO) were used for glycerol steam reforming with and without in-situ CO2 removal at 500 °C and 600 °C. The simultaneous regeneration of catalyst and sorbent was carried out with the mixture gas of N2 and steam at 900 °C. The product gases were measured by a GC gas analyzer. It is obvious that the amounts of CO2, CO and CH4 were reduced in the sorption-enhanced steam reforming of glycerol, and the H2 concentration is greatly increased in the pre-CO2 breakthrough periods within 10 min both 500 °C and 600 °C. The extended time of operation for high-purity hydrogen production and CO2 capture was obtained by the continuous sorption-enhanced steam reforming of glycerol. High-purity H2 products of 93.9% and 96.1% were produced at 500 °C and 600 °C and very small amounts of CO2, CH4 and CO were formed. The decay in activity during the continuous reaction-regeneration of catalyst and sorbent was not observed. [ABSTRACT FROM AUTHOR]

[Display omitted] • Mesoporous Ni-Cu/CeO 2 was successfully synthesized to APR of biodiesel byproduct glycerol. • 1Ni2Cu/CeO 2 presented superior activity and multi-cycle stability in APR. • Cu element in catalysts effectively improved WGS and inhibited CH 4 formation. • Enhanced WGS and reduced methanation were achieved by in-situ CO 2 removal. Aqueous phase reforming (APR), regarded as one method for inexpensive H 2 production, was widely studied due to lower temperature and unnecessary to vaporize water and fuels. In this study, the mesoporous CeO 2 , regarded as a metal oxide carrier, was first prepared by colloidal solution combustion, and then the Ni-Cu bimetallic supported on mesoporous CeO 2 was successfully synthesized to investigate the catalytic performance in APR of biodiesel byproduct glycerol. The results show that the Cu element in the catalysts can effectively improve water–gas shift (WGS) reaction and inhibit the formation of methane, which increases the H 2 production rate from 125.08 to 195.57 µmol⋅min−1⋅g cat−1. The higher reaction temperature is beneficial to the H 2 production rate, but not to H 2 selectivity. Kinetics analysis indicates that catalyst of 1Ni2Cu/CeO 2 + 0.2gCaO has the lowest apparent activation energy (29.86 kJ⋅mol−1). CaO is introduced as an absorbent to improve WGS reaction and reduce methanation reactions through in-situ CO 2 removal and capture. The reaction path and mechanism of APR of glycerol are also discussed in this paper. [ABSTRACT FROM AUTHOR]

Abstract: H2 production from glycerol steam reforming by the Ni–Cu–Al, Ni–Cu–Mg, Ni–Mg catalysts was evaluated experimentally in a continuous flow fixed-bed reactor under atmospheric pressure within a temperature range from 450 to 650 °C. The catalysts were synthesized by the co-precipitation methods, and characterized by the elemental analysis, BET, XRD and SEM. The GC and FTIR were applied to analyze the products from steam reforming of glycerol. The coke deposited on the catalysts was measured by TGA experiments during medium temperature oxidation. The results showed that glycerol conversion and H2 production were increased with increasing temperatures, and glycerol decomposition was favored over its steam reforming at low temperatures. The Ni–Cu–Al catalyst containing NiO of 29.2 wt%, CuO of 31.1 wt%, Al2O3 of 39.7 wt% performed high catalytic activity, and the H2 selectivity was found to be 92.9% and conversion of glycerol was up to 90.9% at 650 °C. The deactivation of catalysts due to the formation and deposition of coke was observed. An improved iterative Coats–Redfern method was used to evaluate the non-isothermal kinetic parameters of coke removal from catalysts, and the results showed the reaction order of n = 1 and 2 in the Fn nth order reaction model predicted accurately the main phase in the coke removal for the regeneration of Ni–Mg and Ni–Cu–Al catalysts, respectively. [Copyright &y& Elsevier]

Abstract: About 10wt.% of glycerol can be produced during the conversion of vegetable oils or animal fats into biodiesel fuel by the transesterification process. To make use of glycerol and increase its values, H2 production from catalytic steam reforming of glycerol by Ni–Mg–Al based catalysts was evaluated experimentally in a fixed-bed reactor under atmospheric pressure within a temperature range of 450–650°C. The thermodynamic analysis was conducted by using a non-stoichiometric methodology based on the minimization of Gibbs free energy. The Ni–Mg–Al based catalysts were synthesized by the co-precipitation method with rising pH technique. The synthesized catalysts were characterized by the elemental analysis, BET, XRD and SEM methods. All the metals in the catalyst remained in oxide forms and the catalysts had the specific surface areas from 98.542 to 126.777m2/g for different compositions. The results showed that glycerol conversion and H2 selectivity were increased with increasing temperatures from 450 to 650°C. The formations of CH4 and CO in the glycerol steam reforming were almost negligible. Carbon formation in glycerol steam reforming was serious in low temperatures. The catalyst containing NiO of 24.1wt.%, MgO of 26.1wt.% and Al2O3 of 49.8wt.% performed appreciable catalytic activity, and the H2 selectivity was found to be 78.5% and conversion of glycerol was up to 88.0% at 650°C. The effects of the operating conditions including temperature, the ratio of steam to carbon (S/C), glycerol inlet concentration and flow rate of carrier gas on glycerol steam reforming by the optimized catalyst were tested. Based on a kinetic model assuming the power law with a first reaction order, the activation energy and the frequency factor for glycerol steam reforming by the Ni–Mg–Al based catalysts were calculated. [Copyright &y& Elsevier]

Abstract: Hydrogen production from steam reforming of glycerol in a fluidized bed reactor has been simulated using a CFD method by an additional transport equation with a kinetic term. The Eulerian–Eulerian two-fluid approach was adopted to simulate hydrodynamics of fluidization, and chemical reactions were modelled by laminar finite-rate model. The bed expansion and pressure drop were predicted for different inlet gas velocities. The results showed that the flow system exhibited a more heterogeneous structure, and the core-annulus structure of gas–solid flow led to back-mixing and internal circulation behaviour, and thus gave a poor velocity distribution. This suggests the bed should be agitated to maintain satisfactory fluidizing conditions. Glycerol conversion and H2 production were decreased with increasing inlet gas velocity. The increase in the value of steam to carbon molar ratio increases the conversion of glycerol and H2 selectivity. H2 concentrations in the bed were uneven and increased downstream and high concentrations of H2 production were also found on walls. The model demonstrated a relationship between hydrodynamics and hydrogen production, implying that the residence time and steam to carbon molar ratio are important parameters. The CFD simulation will provide helpful data to design and operate a bench scale catalytic fluidized bed reactor. [ABSTRACT FROM AUTHOR]

Catalytic steam reforming of glycerol for H2 production has been evaluated experimentally in a continuous flow fixed-bed reactor. The experiments were carried out under atmospheric pressure within a temperature range of 400–700°C. A commercial Ni-based catalyst and a dolomite sorbent were used for the steam reforming reactions and in situ CO2 removal. The product gases were measured by on-line gas analysers. The results show that H2 productivity is greatly increased with increasing temperature and the formation of methane by-product becomes negligible above 500°C. The results suggest an optimal temperature of ∼500°C for the glycerol steam reforming with in situ CO2 removal using calcined dolomite as the sorbent, at which the CO2 breakthrough time is longest and the H2 purity is highest. The shrinking core model and the 1D-diffusion model describe well the CO2 removal under the conditions of this work. [Copyright &y& Elsevier]

[Display omitted] • Hydrogen was efficiently produced from CLSR of biodiesel byproduct glycerol. • Well-order mesoporous CeNiO/MCM-41 and CeNiO/SBA-15 were synthesized for CLSR. • High feeding conversion and H 2 selectivity was achieved by mesoporous OCs. • High loading NiO and CeO 2 on mesoporous OCs achieved excellent CLSR redox cycles. The selection of metal oxides and supports to improve catalytic activity and stability of oxygen carriers (OCs) is crucial for chemical looping steam reforming (CLSR) to hydrogen production. In this study, the Ni-based MCM-41 and SBA-15 OCs with and without CeO 2 promoter were prepared by direct synthesis and impregnation methods. The BET, XRD, TEM, ICP-AES, H 2 -TPR and DSC-TGA were used to analyze the synthesized OCs. Hydrogen production by CLSR using biodiesel byproduct glycerol was studied in a fixed-bed reactor with fuel and air stages. The DSC-TGA experiments were carried out to determine the thermal decomposition of biodiesel byproduct glycerol and the results indicated the exothermic and/or endothermic reactions as a result of secondary reactions and, the main degradation with the mass loss of 85.5 wt% occurred in the stages of 150–500 °C. The mesoporous OCs presented high specific surface area, large pore volume, and uniform pore size. It was found that the NiO and CeO 2 in the mesoporous OCs were first reduced by fuels and the reduced OCs was responsible of steam reforming and water gas shift (WGS) to hydrogen production, and hydrogen selectivity was up to 90% using CeNiO/SBA-15. The mesoporous OCs with Ce promoter greatly shortened 'dead time' (the reduce time of OCs), and effectively suppressed carbon deposited on OCs. High loading of NiO and CeO 2 on SBA-15 improved oxygen transfer and achieved excellent cyclic stability. These findings provide the fundamental understanding and principle of design on the conventional Ni-based OCs with room for further developments in chemical looping process. [ABSTRACT FROM AUTHOR]

The research describes the synthesis of nanocomposite Ni@ZrO 2 oxygen carriers (OCs) and lanthanide doping effect on maintaining the platelet-structure of the nanocomposite OCs. The prepared OCs were tested in chemical looping reforming of glycerol (CLR) process and sorption enhanced chemical looping reforming of glycerol (SE-CLR) process. A series of characterization techniques including N 2 adsorption-desorption, X-ray diffraction (XRD), inductively coupled plasma optical emission spectrometry (ICP-OES), high resolution transmission electron microscopy (HRTEM), H 2 temperature-programmed reduction (H 2 -TPR), H 2 pulse chemisorption and O 2 temperature-programmed desorption (O 2 -TPD) were used to investigate the physical properties of the fresh and used OCs. The results show that the platelet-stack structure of nanocomposite OCs could significantly improve the metal support interaction (MSI), thus enhancing the sintering resistance. The effect of lanthanide promotion on maintaining this platelet-stack structure increased with the lanthanide radius, namely, La 3+ > Ce 3+ > Pr 3+ > Yb 3+ . Additionally, the oxygen mobility was also enhanced because of the coordination of oxygen transfer channel size by doping small radius lanthanide ions. The CeNi@ZrO 2 showed a moderate ‘dead time’ of 220 s, a high H 2 selectivity of 94% and a nearly complete glycerol conversion throughout a 50-cycle CLR test. In a 50-cycle SE-CLR stability test, the CeNi@ZrO 2 CaO showed high H 2 purity of 96.3%, and an average CaCO 3 decomposition percentage of 53% without external heating was achieved. [ABSTRACT FROM AUTHOR]

Abstract: A detailed comparative study on thermodynamic and experimental analyses of glycerol reforming for hydrogen production has been conducted in terms of the effects of temperature, pressure, water to glycerol feed ratio, feeding reactants to inert gas ratio and feeding gas flow rate (residence time). The thermodynamic analysis was conducted by using a non-stoichiometric methodology based on the minimisation of Gibbs free energy. And the experiments were carried out with a pilot scale set-up. The results show that the thermodynamic and experimental data agree fairly well with each other. The measured hydrogen production is slightly lower than that predicted by the thermodynamic analysis, which is mainly because the conversion of steam is incomplete. High temperature, low pressure, low feeding reactants to inert gas ratio and low gas flow rate are favourable for steam reforming of glycerol for hydrogen production. There is an optimal water to glycerol feed ratio for steam reforming of glycerol for hydrogen production which is about 9.0. The glycerol conversion is a strong function of water to glycerol ratio, whereas a weak function of other parameters over the conditions of this work. A novel adsorption enhanced reaction process incorporating water and heat recovery is proposed for further optimisation of hydrogen production from steam reforming of glycerol. [ABSTRACT FROM AUTHOR]