Search

Tandem structure provides a practical way to realize high efficiency organic photovoltaic cells, it can be used to extend the wavelength coverage for light harvesting. The interconnecting layer (ICL) between subcells plays a critical role in the reproducibility and performance of tandem solar cells, yet the processability of the ICL has been a challenge. In this work the fabrication of highly reproducible and efficient tandem solar cells by employing a commercially available material, PEDOT:PSS HTL Solar (HSolar), as the hole transporting material used for the ICL is reported. Comparing with the conventional PEDOT:PSS Al 4083 (c‐PEDOT), HSolar offers a better wettability on the underlying nonfullerene photoactive layers, resulting in better charge extraction properties of the ICL. When FTAZ:IT‐M and PTB7‐Th:IEICO‐4F are used as the subcells, a power conversion efficiency (PCE) of 14.7% is achieved in the tandem solar cell. To validate the processability of these tandem solar cells, three other research groups have successfully fabricated tandem devices using the same recipe and the highest PCE obtained is 16.1%. With further development of donor polymers and device optimization, the device simulation results show that a PCE > 22% can be realized in tandem cells in the near future. [ABSTRACT FROM AUTHOR]

Molecular doping is often used in organic semiconductors to tune their (opto)electronic properties. Despite its versatility, however, its application in organic photovoltaics (OPVs) remains limited and restricted to p‐type dopants. In an effort to control the charge transport within the bulk‐heterojunction (BHJ) of OPVs, the n‐type dopant benzyl viologen (BV) is incorporated in a BHJ composed of the donor polymer PM6 and the small‐molecule acceptor IT‐4F. The power conversion efficiency (PCE) of the cells is found to increase from 13.2% to 14.4% upon addition of 0.004 wt% BV. Analysis of the photoactive materials and devices reveals that BV acts simultaneously as n‐type dopant and microstructure modifier for the BHJ. Under optimal BV concentrations, these synergistic effects result in balanced hole and electron mobilities, higher absorption coefficients and increased charge‐carrier density within the BHJ, while significantly extending the cells' shelf‐lifetime. The n‐type doping strategy is applied to five additional BHJ systems, for which similarly remarkable performance improvements are obtained. OPVs of particular interest are based on the ternary PM6:Y6:PC71BM:BV(0.004 wt%) blend for which a maximum PCE of 17.1%, is obtained. The effectiveness of the n‐doping strategy highlights electron transport in NFA‐based OPVs as being a key issue. [ABSTRACT FROM AUTHOR]

Abstract: Achieving efficient bulk‐heterojunction (BHJ) solar cells from blends of solution‐processable small‐molecule (SM) donors and acceptors is proved particularly challenging due to the complexity in obtaining a favorable donor–acceptor morphology. In this report, the BHJ device performance pattern of a set of analogous, well‐defined SM donors—DR3TBDTT (DR3), SMPV1, and BTR—used in conjunction with the SM acceptor IDTTBM is examined. Examinations show that the nonfullerene “All‐SM” BHJ solar cells made with DR3 and IDTTBM can achieve power conversion efficiencies (PCEs) of up to ≈4.5% (avg. 4.0%) when the solution‐processing additive 1,8‐diiodooctane (DIO, 0.8% v/v) is used in the blend solutions. The figures of merit of optimized DR3:IDTTBM solar cells contrast with those of “as‐cast” BHJ devices from which only modest PCEs <1% can be achieved. Combining electron energy loss spectrum analyses in scanning transmission electron microscopy mode, carrier transport measurements via “metal‐insulator‐semiconductor carrier extraction” methods, and systematic recombination examinations by light‐dependence and transient photocurrent analyses, it is shown that DIO plays a determining role—establishing a favorable lengthscale for the phase‐separated SM donor–acceptor network and, in turn, improving the balance in hole/electron mobilities and the carrier collection efficiencies overall. [ABSTRACT FROM AUTHOR]

'Nonfullerene' acceptors are proving effective in bulk heterojunction (BHJ) solar cells when paired with selected polymer donors. However, the principles that guide the selection of adequate polymer donors for high-efficiency BHJ solar cells with nonfullerene acceptors remain a matter of some debate and, while polymer main-chain substitutions may have a direct influence on the donor-acceptor interplay, those effects should be examined and correlated with BHJ device performance patterns. This report examines a set of wide-bandgap polymer donor analogues composed of benzo[1,2- b:4,5- b′]dithiophene (BDT), and thienyl ([2H]T) or 3,4-difluorothiophene ([2F]T) motifs, and their BHJ device performance pattern with the nonfullerene acceptor 'ITIC'. Studies show that the fluorine- and ring-substituted derivative PBDT(T)[2F]T largely outperforms its other two polymer donor counterparts, reaching power conversion efficiencies as high as 9.8%. Combining several characterization techniques, the gradual device performance improvements observed on swapping PBDT[2H]T for PBDT[2F]T, and then for PBDT(T)[2F]T, are found to result from (i) notably improved charge generation and collection efficiencies (estimated as ≈60%, 80%, and 90%, respectively), and (ii) reduced geminate recombination (being suppressed from ≈30%, 25% to 10%) and bimolecular recombination (inferred from recombination rate constant comparisons). These examinations will have broader implications for further studies on the optimization of BHJ solar cell efficiencies with polymer donors and a wider range of nonfullerene acceptors. [ABSTRACT FROM AUTHOR]

Organic Solar Cells: High-Performance Tandem Organic Solar Cells Using HSolar as the Interconnecting Layer (Adv. Keywords: interconnecting layers; organic photovoltaics; tandem solar cells EN interconnecting layers organic photovoltaics tandem solar cells 1 1 1 07/09/20 20200707 NES 200707 In article number 2000823, Carr Hoi Yi Ho, Franky So and co-workers presented a simple yet highly compatible interconnecting layer for organic tandem solar cells. In addition, most of the tandem devices achieve more than 40% enhancement from the single-junction solar cell. [Extracted from the article]

A simple approach that enables a consistent enhancement of the electron extracting properties of the widely used small‐molecule Phen‐NaDPO and its application in organic solar cells (OSCs) is reported. It is shown that addition of minute amounts of the inorganic molecule Sn(SCN)2 into Phen‐NaDPO improves both the electron transport and its film‐forming properties. Use of Phen‐NaDPO:Sn(SCN)2 blend as the electron transport layer (ETL) in binary PM6:IT‐4F OSCs leads to a remarkable increase in the cells' power conversion efficiency (PCE) from 12.6% (Phen‐NaDPO) to 13.5% (Phen‐NaDPO:Sn(SCN)2). Combining the hybrid ETL with the best‐in‐class organic ternary PM6:Y6:PC70BM systems results to a similarly remarkable PCE increase from 14.2% (Phen‐NaDPO) to 15.6% (Phen‐NaDPO:Sn(SCN)2). The consistent PCE enhancement is attributed to reduced trap‐assisted carrier recombination at the bulk‐heterojunction/ETL interface due to the presence of new energy states formed upon chemical interaction of Phen‐NaDPO with Sn(SCN)2. The versatility of this hybrid ETL is further demonstrated with its application in perovskite solar cells for which an increase in the PCE from 16.6% to 18.2% is also demonstrated. [ABSTRACT FROM AUTHOR]

The reported power conversion efficiencies (PCEs) of nonfullerene acceptor (NFA) based organic photovoltaics (OPVs) now exceed 14% and 17% for single‐junction and two‐terminal tandem cells, respectively. However, increasing the PCE further requires an improved understanding of the factors limiting the device efficiency. Here, the efficiency limits of single‐junction and two‐terminal tandem NFA‐based OPV cells are examined with the aid of a numerical device simulator that takes into account the optical properties of the active material(s), charge recombination effects, and the hole and electron mobilities in the active layer of the device. The simulations reveal that single‐junction NFA OPVs can potentially reach PCE values in excess of 18% with mobility values readily achievable in existing material systems. Furthermore, it is found that balanced electron and hole mobilities of >10−3 cm2 V−1 s−1 in combination with low nongeminate recombination rate constants of 10−12 cm3 s−1 could lead to PCE values in excess of 20% and 25% for single‐junction and two‐terminal tandem OPV cells, respectively. This analysis provides the first tangible description of the practical performance targets and useful design rules for single‐junction and tandem OPVs based on NFA materials, emphasizing the need for developing new material systems that combine these desired characteristics. [ABSTRACT FROM AUTHOR]

Semi-transparent (ST) tandem organic solar cells (OSCs) are typically exhibiting a trade-off between efficiency and average visible transmittance (AVT), which can be minimized by the appropriate selection of transparent contacts and absorbing materials in the sub-cells. Herein, we demonstrate efficient and highly transparent hetero-tandem OSCs constructed by stacking PBDT[2F]T:PC 71 BM and PCE10:PC 61 BM active layers as front-cell and back-cell, respectively. Optical and electrical simulations show that the PBDT[2F]T and PCE10-based sub-cells possess potential as ST and reflective tandem OSCs. With the aid of the simulations, we could fabricate reflective tandem OSCs with an efficiency of up to 8.3%. Furthermore, a ST tandem OSC, employing conductive silver nanowire top contact, achieved an AVT of 49.2%, efficiency of 5.3%, and high light utilization efficiency (LUE) of 2.61% under 1 sun, AM1.5G spectral illumination. This study demonstrates the importance of the sub-cells choices for developing ST tandem solar cells with a good balance of AVT and PCE, paving the way for solar windows of high performance. [Display omitted] • Optical and electrical simulations performed to aid reflective and semi-transparent tandem OSCs fabrication. • Fabrication of tandem based on PBDT[2F]T:PC 71 BM and PCE10:PC 61 BM blends with PCE higher than their single-cells (8.2%). • Semi-transparent tandem device with a very high AVT of nearly 50%, in agreement with optical simulation. • The semi-transparent tandem based on PBDT[2F]T:PC 71 BM and PCE10:PC 61 BM blends achieved high PCE of 5.3% and LUE of 2.61%. [ABSTRACT FROM AUTHOR]