Search

The fabrication of new membrane that is able to produce stable high power density is essential for the development of pressure retarded osmosis (PRO) technology. In this work, thin film composite (TFC) polyetherimide membranes with three different substrate structures were fabricated and characterized. The PRO performance of the resultant membrane was evaluated through two pressure cycle experiments and stability tests. The primary objective of this work is to systematically study PRO membrane’s mechanical stability and mass transfer properties under high operating pressures, which determine the power density of the membrane in the PRO process. Experiments revealed that water permeability ( A p ) and salt permeability ( B p ) under different pressures varied. The A p and B p are better indicators for examining the variation of PRO membrane structure under pressure. Within the operating pressure range of 17.2 bar, the top polyamide layer of TFC PEI-2# membrane mainly experienced a reversible deformation. In the two pressure cycle tests, the water flux, specific salt flux and power density obtained in the upward and downward measurements in each cycle are close to each other. The first cycle and the second cycle also show excellent reproducibility. The membrane was able to maintain almost unchanged water flux and power density of 12.8 W/m 2 at 17.2 bar over the 10 h testing time, suggesting the membrane’s great potential to be used in practical application in the future. [ABSTRACT FROM AUTHOR]

Abstract: For the first time, a specially designed pressure retarded osmosis (PRO) hollow fiber membrane has been successfully developed and applied in the PRO process to demonstrate its potential for power generation. The membrane fabrication method is similar to that used for making thin-film composite (TFC) forward osmosis hollow fiber membranes, but further optimization and improvement have led to a new type of TFC hollow fiber membranes with much greater mechanical strength in addition to its excellent separation property and high water flux. The TFC PRO hollow fiber membranes have a water permeability (A) of 9.22×10−12 m/(sPa), salt permeability (B) of 3.86×10−8 m/s and structural parameter (S) of 4.6×10−4 m. It can withstand hydrostatic pressure as high as 9bar with its relatively large dimension of 0.98mm lumen diameter. This PRO hollow fiber membrane is superior to all other PRO membranes reported in the open literature in terms of power density. A power density as high as 10.6W/m2 can be achieved using seawater brine (1.0M NaCl) and wastewater brine (40mM NaCl), which suggests that the newly developed PRO hollow fiber membrane has great potential to be applied in PRO processes to harvest salinity gradient energy. A higher pressure is preferred as it allows generation of higher power density (pressures of 12bar may be optimal for seawater as the high salinity stream), and this can be realized by reduced fiber dimension. Further optimization of the membrane structure will be performed. [Copyright &y& Elsevier]

Abstract: Forward osmosis (FO) has received intensive studies recently for a range of potential applications such as wastewater treatment, water purification and seawater desalination. One of the major challenges to be overcome is the lack of an optimized FO membrane that can produce a high water flux comparable to commercial RO membranes. Two types of thin-film composite FO hollow fibers with an ultra-thin polyamide-based RO-like skin layer (300–600nm) on either the outer surface (#A-FO) or inner surface (#B-FO) of a porous hollow fiber substrate have been successfully fabricated. These novel composite FO hollow fibers have been characterized by a series of standard protocols and benchmarked against commercially available FO flat sheet membranes and reported NF hollow fibers used for the FO process. The characterization reveals that the FO hollow fiber membranes possess a large lumen. The substrates are highly porous with a narrow pore size distribution. The active layers present excellent intrinsic separation properties with a hydrophilic rejection layer and good mechanical strength. The #B-FO hollow fiber membrane can achieve a high FO water flux of 32.2L/m2 h using a 0.5M NaCl draw solution in the active rejection layer facing draw solution (AL-facing-DS) configuration at 23°C. The corresponding salt flux is only 3.7g/m2 h. To the best of our knowledge, the performance of the #B-FO hollow fiber is superior to all FO membranes reported in the open literature. The current study suggests that the optimal FO membrane structure would possess a very small portion of sponge-like layer in a thin and highly porous substrate, which suggests a way for further improvement. [Copyright &y& Elsevier]

Abstract: There has been a resurgence of interest in forward osmosis (FO) as a potential means of desalination, dewatering and in pressure retarded osmosis, which Sidney Loeb was advocating over 3decades ago. This paper describes the characteristics and potential applications of a newly developed FO hollow fiber membrane, which was fabricated by interfacial polymerization on the inner surface of a polyethersulfone (PES) hollow fiber. This FO membrane presents excellent intrinsic separation properties, with a water flux of 42.6L/m2 h using 0.5M NaCl as the draw solution and DI water as the feed with the active layer facing the draw solution orientation at 23°C. The corresponding ratio of salt flux to water flux was only 0.094g/L, which is superior to all other FO membranes reported in the open literature. To evaluate different application scenarios, various NaCl solutions (500ppm (8.6mM), 1wt.% (0.17M) and 3.5wt.% (0.59M)) were used as the feed water to test the performance of the FO membrane. The membrane can achieve a water flux of 12.4L/m2 h with 3.5wt.% NaCl solution as the feed and 2M NaCl as the draw solution, suggesting it has good potential for seawater desalination. [ABSTRACT FROM AUTHOR]

Abstract Forward osmosis (FO) membranes have received attention as an energy-efficient and low-cost technique in stream concentrating processes. In this work, a novel double-skinned hollow fiber thin film composite (TFC) FO membrane has been successfully fabricated, which consists of a one-step prepared dual layer substrate and a thin inner selective layer formed via interfacial polymerization. The substrate consists of a relatively dense ultrafiltration (UF) outer layer and a porous UF inner layer, both of which were constructed from polyethersulfone (PES) as the substrate material by using dual-layer co-extrusion technique. Compared to the commercial and reported double-skinned FO membranes, the FO membrane developed in this work exhibited a higher permeate flux with humic acid solution as feed. Furthermore, the double-skinned FO membrane was applied in concentrating activated sludge using 0.5 M NaCl as draw solution, and a permeate flux at 5.4 L/m2h was achieved after 5 h operation, which was higher than or comparable to those of the reported FO membranes. Membrane autopsies and foulant analysis suggested that the dense UF skin layer helped to reject greater-sized organic foulants (> 300 Da). This study shed light on the important fabrication features and promising application of the double-skinned hollow fiber TFC FO membrane in sludge concentration. Graphical abstract fx1 Highlights • A dual-layer UF substrate was prepared via a single-step fabrication process. • TFC FO membrane was fabricated via interfacial polymerization in the lumen of the substrate. • FO performance in sludge thickening process was investigated. • Tight UF layer helped rejecting greater-sized organics in sludge. • A permeate flux of 5.4 L/m2h was achieved after 5 h operation using 0.5 M NaCl as draw solution. [ABSTRACT FROM AUTHOR]

The salinity gradient is a renewable and sustainable energy source that can be utilized by a pressure-retarded osmosis (PRO) process. Development of the PRO technology was impeded by shortage of efficient membranes until recent surge on PRO research. In this work, flat-sheet thin film composite (TFC) PRO membranes with reinforced support layer were developed. The membrane properties were optimized by blending high molecular weight polyvinylpyrrolidone (PVP) into the polysulfone (PSf) casting solution. Influences of PVP addition on the kinetic and thermodynamic properties of the casting solution, resultant membrane properties as well as PRO performance were systematically investigated. It is showed that PVP can effectively improve the membrane morphology and pore structure. By adjusting the PSf/PVP composition in the substrate recipe, the reinforced TFC membrane is able to achieve a power density of 12.9 W/m 2 at 22 bar using 1 M NaCl draw solution and pure water feed. Long-term PRO test at the peak power density and multi-pressure cycle tests were performed on the membranes. Consistent power density and low salt flux/water flux ratio were observed in the whole tests. The results demonstrated that the reinforced TFC membrane in this study had excellent mechanical strength and stability. It would be promising for future engineering application. [ABSTRACT FROM AUTHOR]

The emerging thin film composite (TFC) forward osmosis (FO) and pressure retarded osmosis (PRO) membranes generally have better separation properties compared with their cellulose triacetate (CTA) counterparts. Nevertheless, their scaling performance has been rarely reported. In the current study, the phenomenon of membrane integrity loss as a result of scaling is reported for the first time for osmotically driven membrane processes (ODMPs). The results show that the TFC membrane suffered marked flux reduction during the scaling in the active-layer-facing-feed-solution (AL-FS) orientation, accompanied with the severe damage of the membrane active layer. The membrane integrity loss is attributed to the scale formation and growth in the confined space between the membrane and the feed spacer. Compared with the CTA membrane, the TFC was more prone to scaling and membrane damage due to its unfavorable physiochemical properties (presence of Ca 2 + binding sites and ridge-and-valley roughness). Although antiscalant addition was shown to be effective for scaling control in AL-FS, it was ineffective in the active-layer-facing-draw-solution orientation. The current study reveals the critical need for scaling control in ODMP processes with respect to the membrane integrity and flux stability. The results also have far-reaching implications for FO and PRO membrane design and process operation. [ABSTRACT FROM AUTHOR]

Abstract: Polyamide thin film composite (TFC) membranes with tailored porous substrate and rejection layer are promising for forward osmosis (FO) applications. The current study investigates the effect of rejection layer synthesis conditions on the performance of the resulting TFC polyamide FO membranes. The influence of monomer concentrations (i.e., m-phenylenediamine (MPD) and trimesoyl chloride (TMC) concentrations) on the membrane separation properties as well as FO performance was systematically studied. A strong trade-off between the water permeability and salt rejection was observed, where increasing the TMC concentration or reducing the MPD concentration resulted in higher membrane permeability but lower salt rejection. In FO tests, membranes with poor salt rejection had severe solute reverse diffusion, which enhanced the internal concentration polarization (ICP). It was found that the FO water flux was governed by both the membrane water permeability and its solute rejection. For a membrane with higher water permeability but lower solute rejection, the reduced membrane frictional resistance was compensated by the simultaneously more severe solute-reverse-diffusion-induced ICP. The net effect on the FO water flux depends on the competition of these two opposing mechanisms. Under conditions where solute reverse diffusion may cause severe ICP (e.g., high draw solution concentration and high water flux level), membranes need be optimized to achieve a high salt rejection even if this is at the expense of lower water permeability. [Copyright &y& Elsevier]

Abstract: Forward osmosis (FO) technology has become increasingly attractive in the past decades for water related applications and will likely continue to develop rapidly in the future. This calls for the development of high performance FO membranes. Thin film composite (TFC) polyamide FO membranes with tailored support structure were prepared in the current study. The porous polysulfone substrates with finger-like pore structures were prepared via phase inversion, and the polyamide rejection layers were synthesized by interfacial polymerization. The resulting TFC FO membranes had small structural parameters (s =0.67–0.71mm) due to the thin cross-section, low tortuosity, and high porosity of the membrane substrates. Meanwhile, their rejection layers exhibited superior separation properties (higher water permeability and better selectivity) over commercial FO membranes. When the rejection layer is oriented towards the draw solution, FO water flux as high as 54L/m2 h can be achieved with a 2M NaCl draw solution while maintaining relatively low solute reverse diffusion. Comparison of the synthesized TFC FO membranes with commercial FO and RO membranes reveals the critical importance of the substrate structure, with straight finger-like pore structure preferred over spongy pore structure to minimize internal concentration polarization. In addition, membranes with high water permeability and excellent selectivity are preferred to achieve both high FO water flux and low solute flux. [Copyright &y& Elsevier]