Search

The aim of this work was to investigate the possibility of doping copper sulfide Cu2S with selected fifth-group elements, potentially having a positive effect on the thermoelectric properties of the resulting materials. For the selected model structures, theoretical calculations and an analysis of the electronic structure and changes in the enthalpy of formation due to doping were performed using the WIEN2k package employing the Full-Potential Linearized Augmented Plane Wave (FP-LAPW) method within density functional theory (DFT) formalism. Polycrystalline materials with the nominal composition of Cu32S15X1 (X = P, As, Sb, Bi) were synthesized in quartz ampoules, then sintered using the spark plasma sintering (SPS) technique and "SPS melting" method. The chemical and phase compositions of the obtained sinters were studied by X-Ray diffraction (XRD) and scanning electron microscopy (SEM). Additionally, investigations of thermoelectric properties, i.e., electrical conductivity, Seebeck coefficient and thermal conductivity in the temperature range 300–920 K, were performed. The results of this study indicate that only phosphorus is successfully incorporated into the Cu₂S structure. [ABSTRACT FROM AUTHOR]

In this work, the electrocaloric effect (ECE) and electrocaloric strength (ΔT/E) were measured and thermal and dielectric studies were performed on Pb-modified BaTiO3 (BPT). The saturated hysteresis loops and normal ferroelectric behavior of the ferroelectric ceramics allow the utilization of the indirect method to estimate the electrocaloric properties. The electrocaloric measurements were performed under high (18 kV/cm) versus low (8 kV/cm) electric field conditions. These conditions were chosen to notice and then eliminate an artificial negative electrocaloric effect in the tested ceramics. At the same time, relatively high values of positive electrocaloric temperature change ΔT ( ~   2.19   K ) and electrocaloric strength ΔT/E ( ~ 0.27–0.11 K · cm/kV) were obtained. [ABSTRACT FROM AUTHOR]

In this paper, physicochemical properties of pure Y2O3 and samarium (Sm)-doped Y2O3 transparent ceramics obtained via arc plasma melting are presented. Yttria powder with a selected molar fraction of Sm was first synthesized by a solid-state reaction method. High transparent yttria ceramics were obtained by arc plasma melting from both the pure and Sm oxide-doped powders. The morphological, chemical and physical properties were investigated by X-ray diffraction and scanning electron microscopy. The optical band gap was calculated from the absorption spectra so as to understand the electronic band structure of the studied materials. Samples indicate a series of luminescence bands in the visible region after excitation by laser light in the range from 210 to 250 nm. Magneto-optical measurements were carried out in the 300–800 nm range at room temperature. It can be seen that a maximum Verdet constant ca. 24.81 deg/T cm was observed for 405 nm and this value decreases with increasing wavelength. The potential usefulness of the polycrystalline material dedicated to optics devices is presented.

In this work, a mid infrared thermography was used to study thermal behavior of solid oxide fuel cell (SOFC) with a circular shape and a diameter of 90 mm. The emissivity of the anodic surface of the fuel cell was determined to be from 0.95 to 0.46 in the temperature range 550-1200 K and the profile and temperature distribution of the anodic surface of the unloaded cell was given. The surface temperature of the cell was determined during operation and the polarity changes from open circuit voltage (OCV) to 0.0 V. It was found that the cell self-heating effect decreases with increasing temperature of the cell.

The aim of this work was to investigate the possibility of obtaining an amorphous/crystalline composite starting from Ni-Si- B-based powder grade 1559-40 and silver powder. The alloy was produced using arc melting of 95% wt. Ni-Si-B-based powder (1559-40) and 5% wt. Ag powder. Ingot was re-melted on a copper plate and observed while cooling using a mid-wave infra-red camera. The alloy was then melt-spun in a helium atmosphere. The microstructure of the ingot as well as the melt-spun ribbon was studied using light microscopy and scanning electron microscopy with energy dispersive spectrometry. Phase identification was performed by means of X-ray diffraction. The observations confirmed an amorphous/crystalline microstructure of the ribbon where the predominant constituent of the microstructure was an amorphous phase enriched with Ni, Si, and B, while the minor constituent was an Ag-rich crystalline phase distributed in a film along the melt-spinning direction.

K0.5Na0.5NbO3:xEu sol–gel powders and bulk samples were synthesized by means of a modified sol–gel method. Two types of samples were obtained via sintering at two temperatures. X-ray diffraction revealed the presence of the perovskite phase in materials obtained at both temperatures. Eu3+ emission and excitation studies were conducted to determine its luminescence response. For K0.5Na0.5NbO3:xEu sinters, the excitation spectra included narrow peaks in the VIS range due to the 5D0–7F1 and 5D0–7F2 relaxation processes. These transitions were indicative of the presence of Eu3+ at sites of low symmetry. Dielectric studies indicated that Eu2O3 affected the observed phase transitions. The influence of sintering temperature on structure and physicochemical properties was discussed. [ABSTRACT FROM AUTHOR]

This research explores the welding process of a high-entropy CrMnFeCoNi alloy with iron, unraveling the intricate chemical compositions that materialize in distinct regions of the weld joint. A mid-wave infrared thermal camera was deployed to monitor the cooling sequences during welding. A thorough analysis of the metallographic sample from the weld joint, along with measurements taken using a nano-hardness indenter, provided insights into the hardness and Young's modulus. The element distribution across the weld joint was assessed using a scanning electron microscope equipped with an EDS spectrometer. Advanced techniques such as X-ray diffraction and Mössbauer spectroscopy underscored the prevalence of the martensitic phase within the weld joint, accompanied by the presence of bcc (iron) and fcc phases. In contrast, Young's modulus in the base metal areas displayed typical values for a high-entropy alloy (202 GPa) and iron (204 GPa). The weld joint material displayed substantial chemical heterogeneity, leading to noticeable concentration gradients of individual elements. The higher hardness noted in the weld (up to 420 HV), when compared to the base metal regions (up to 290 HV for CrMnFeCoNi alloy and approximately 150 HV for iron), can be ascribed to the dominance of the martensitic phase. These findings provide valuable insights for scenarios involving diverse welded joints containing high-entropy alloys, contributing to our understanding of materials engineering. [ABSTRACT FROM AUTHOR]

The aim of this work was to investigate the microstructure and mechanical properties of the two-component melt-spun (TCMS) alloy produced from Ni40Fe40B20 and Ni70Cu10P20 melts. The Ni40Fe40B20, Ni70Cu10P20, Ni55Fe20Cu5P10B10 alloys were arc-melted. Then the alloys were melt-spun in the two different ways i.e.: by casting from a single-chamber crucible and from the two-chamber crucible. All of the above mentioned alloys were processed in the first way and the Ni40Fe40B20 and Ni70Cu10P20 were simultaneously cast on the copper roller from the two-chamber crucible. The microstructure of the alloy was studied using transmission electron microscopy (TEM), scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS) and light microscopy. The mechanical properties were investigated using tensile testing and nanoindentation. The two-component melt-spun (TCMS) amorphous Ni55Fe20Cu5P10B10 alloy present hardness, tensile strength and Young modulus on the significantly higher level than for a single phase amorphous Ni55Fe20Cu5P10B10 alloy and slightly below the corresponding values for the Ni40Fe40B20.

This work presents the microstructure and properties of two‐phase amorphous melt‐spun alloys ejected from the crucible with partition between liquids. The microstructure was studied by scanning electron microscopy and transmission electron microscopy and the phase composition was studied by X‐ray diffraction. The thermal stability of the alloys was determined using differential scanning calorimetry. The microstructure study proves that the composite alloys are heterogeneous because of the existence of the two amorphous phases obtained due to the use of a partition between the liquids. This microstructure correlates with complex thermal characteristics not found in homogeneous alloys of the same nominal composition. The layered structure of these composites influences the formation of fractures during tensile tests. LAY DESCRIPTION: The aim of this investigation is to present the special features and properties of the glassy two‐component melt‐spun alloys in comparison to the melt‐spun alloys ejected from single‐chamber crucible. The studies of the composite microstructure were performed using transmission electron microscopy and scanning electron microscopy. The alloys also were heated to elevated temperatures and their characteristics were studied by means of differential scanning calorimetry. The phase composition of the alloys was investigated using X‐ray diffraction. The results of the microstructure examination show that these alloys are heterogeneous due to the production method. The special feature of the alloys is that they essentially inherit the transformations possible to occur in the precursor alloys after amorphisation of the these precursors. Results of thermal analysis also confirm the occurrence of transformations of the regions from the transition zones of the intermediate compositions between the two main constituents A and B. These transformations are found to be similar to the transformations identified in the amorphous alloys of the averaged compositions, that is, the homogeneous chemical compositions that are possible for obtaining, when alloys A and B are molten together to form a single liquid phase before ejection into a spinning cylinder. Unique feature of these composite alloys is lamellar morphology. This microstructure consists mainly of the stripes/layers of precursor alloys A and B that are inserted into each chamber of the two‐chamber crucibles. After ejection of the alloys into the surface of the spinning cooper wheel, they form the microstructure of the layered morphology. This band‐like morphology affects formation of the ductile fracture. Actually, this relationship is confirmed by observation of the fracture surfaces of the composite samples. The scanning electron microscopy observations with mappings of the chemical composition performed for all of the composite ribbons show that their microstructure consists of the layers of differentiated chemical compositions parallel to the surface of the ribbon. The arrangement of vein‐like pattern of the fractures coincides with the boundaries between the regions of the differentiated chemical compositions. [ABSTRACT FROM AUTHOR]

The paper presents results of the mechanical testing and the microstructure analysis of dissimilar welded joint of the R350HT steel and the high-manganese (Hadfield) cast steel using Cr-Ni cast steel spacer. The simulation tests of the welded joint surface deformation were carried out. The macroscopic and microscopic investigation were made using light microscopy (LM) and scanning electron microscopy (SEM). Content of the magnetic phase was measured using magnetoscope. The quantitative metallographic investigation was used for assessment of ferrite and martensite contents and X-ray diffraction phase analysis was carried out. The results showed that during cooling of the spacer after welding, the transformation of metastable austenite into martensite proceeded. In addition to work hardening, the phase transformation of austenite into martensite occurs during the process of the superficial deformation of the spacer while simulated exploitation. This leads to a substantial increase of hardness, and at the same time, causes the increase of wear resistance of the welded joints of crossovers.

The article presents the results of Transvarestraint test of a modern precipitation hardened steel X10CrNiCuNb18-9-3 with copper. For comparison, the results of tests of conventional steel without the addition of copper X5CrNi18-10 are presented. The total length of all cracks and the maximum length of cracks were measured. The study of microstructure (LM, SEM) showed that the austenitic stainless steel X10CrNiCuNb18-9-3 is very prone to hot cracking. After performing the Transvarestraint tests three types of cracks were observed: solidification cracks occurring during crystallization, liquation cracks due to segregation in the heat affected zone (HAZ) and surface cracks. Niobium carbonitrides dispersed in the bands of segregation are the reason of high susceptibility to liquation cracking. Segregation of copper occurring during solidification causes of surface cracking. A combined effect of copper and stresses contributes to formation of hot microcracks. These microcracks propagate to a depth of 20-30 μm.

The paper presents rezults of microstructure (LM, TEM) investigation and hardness measurments of welded joints in martensitic precipitation hardened stainless steel containing copper, subjected to heat treatment. For the aging temperature up to 540 °C even for the very long times, the microstructure of the welded joints is similar to this one at lower temerature aging. After aging at 620 °C a distinct change of the microstructure was observed. Non-equilibrium solidification conditions of the weld metal, segregation and the diffusion of copper and the elements stablilizing the austenite cause the occurrence of the reverse transformation of the martensite into austenite as fast as just 1 hour at 620 °C. TEM investigations revealed the differences in dispersion of hardening copper precipitates after aging at temperature 620 °C for 1 and 4 hours.

The article discusses new and republished translations of Susan Sontag’s work, recently launched by the Karakter publishing house: Regarding the Pan of Others, On Photography, and Against Interpretation and Other Essays. The article focuses on the elements of Sontag’s thought that make her a forgotten mother of feminist and gender theoreticians, as well as such influential critics as Michel Foucault and Roland Barthes. The article points out to continuations of Sontag’s thought in contemporary theoretical and social projects, and to the pertinence of her critical observations on theories based on metaphysics of presence: psychoanalysis, Marxism, or hermeneutics. The article also touches upon history of war photography and related war journalism, and upon the ambivalent quality of imaging of the misery of war. It also present historical and cultural circumstances of the development of Sontag’s thought in the intellectual milieu of New York in the 1960s. The discussion recapitulates the main statements of Sontag’s essays, relating them to a wider theoretical context, which is aimed at a reappraisal of the forgotten intelectual in the history of literature.

In this paper, physicochemical properties of pure Y2O3 and samarium (Sm)-doped Y2O3 transparent ceramics obtained via arc plasma melting are presented. Yttria powder with a selected molar fraction of Sm was first synthesized by a solid-state reaction method. High transparent yttria ceramics were obtained by arc plasma melting from both the pure and Sm oxide-doped powders. The morphological, chemical and physical properties were investigated by X-ray diffraction and scanning electron microscopy. The optical band gap was calculated from the absorption spectra so as to understand the electronic band structure of the studied materials. Samples indicate a series of luminescence bands in the visible region after excitation by laser light in the range from 210 to 250 nm. Magneto-optical measurements were carried out in the 300–800 nm range at room temperature. It can be seen that a maximum Verdet constant ca. 24.81 deg/T cm was observed for 405 nm and this value decreases with increasing wavelength. The potential usefulness of the polycrystalline material dedicated to optics devices is presented. [ABSTRACT FROM AUTHOR]

This paper presents the diversity of social penetration rates of information and communication technologies (ICT) among selected European countries according to European statistics on diverse ICT indicators. The data considered cover the 2006–2010 time range and was obtained from the Eurostat portal. The scope of the study selected EU countries – Belgium, Germany, France, Finland, Sweden, Bulgaria, Czech Republic, Poland, Slovenia, Spain. The following ICT indicators were analyzed: percentage of households or corporations with broadband access to the Internet (HHBAI), percentage of individuals who are regularly using the Internet (IRUI), percentage of individuals who ordered goods or services over the Internet (IOGSI). These indicators of ICT penetration rate in the countries examined were analyzed in terms of the following aspects: forecasting (estimates until the year 2035) , maximum speed of change of these indicators (the pace of social penetration of information technology), delays or advances (in years) as compared to the averages in EU. The results are presented in tables and graphs. General conclusions and directions of future research are indicated at the end of the paper.

The aim of the article is to present the role of a father in a child upbringing in the early school age. The paper consists of theoretical and research parts. The first part describes father’s role as an educator in child’s life, the influence of the father’s values on child’s upbringing, the father’s authority and reasons for father’s absence in child’s life. The second part presents analysis of the research results. Seven children of early school aged have participated in the study. The methods used in the study were observation, interviews with supervising teacher and document analysis. The subject of the study was the relationship of the father with the early school-age child. The influence of the father’s participation in the child’s upbringing on the child’s self-esteem and perception of reality was being examined. The effect of father’s absence on the child’s behavior and self-esteem was being analyzed. The study showed a relationship between father’s participation in child upbringing and high or inflated self-esteem and the child’s positive attitude towards reality. The relationship between father’s absence and lowered self-esteem of the subjects was presented. [ABSTRACT FROM AUTHOR]

There is a problem in obtaining a suitable impact strength of the padding weld after cladding with a martensitic filler metal. Too low annealing temperature below 580°C and the excessive annealing temperature above 650°C do not provide adequate impact strength of the padding weld. A heat treatment technology for mixed joints has been developed based on the results of the microscopic observations, X-ray diffraction measurements and transmission electron microscope examination. The problem was identified and a special technology of heat treatment for the dissimilar joint was elaborated. This technology provides a high impact resistance of the padding weld and an appropriate properties of the base material. [ABSTRACT FROM AUTHOR]

The paper presents the results of the investigation of microstructure of the welded X5CrNiCuNb16-4 (17-4PH) steel after solution treatment and aging at 620°C for different periods. The microstructure and the phase composition of the steel was investigated using light microscopy (LM), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), transmission electron microscopy (TEM) and the X-ray diffraction (XRD). Hardness was measured for samples aged at different times. Density distributions of Cu precipitates were established. The investigation has shown that the microstructure of the X5CrNiCuNb16-4 steel welds after aging at 620 ° C consists of tempered martensite, fine Cu precipitates and austenite. It was observed that the size of the Cu precipitates increases with increasing the aging time, what affects the decrease of hardness. Simultaneously, the quantity of reversed austenite increases with increase of aging time. It was revealed that enrichment of the austenite in Ni, Cu and C affects the increase of Ms, but this factor does not determine the stability of austenite. [ABSTRACT FROM AUTHOR]

Crystalline-amorphous matrix composites preserve the amorphous material high strength and additionally gains on plasticity. Substituting hard crystalline precipitates with soft ones should even more improve the latter. Therefore, this work was aimed at verifying, whether Ag and Ni-Si-B alloy shows liquid immiscibility and consequently, if they might form crystalline Ag/Ni-Si-B amorphous/crystalline composite. Firstly, a mixture of 95 wt% of Ni-Si-B (1559-40) and 5 wt% of Ag powders was arc-melted in argon and cooled at copper plate. The solidification process was documented by IR mid-wave camera and Time/Temperature graph. The microstructure of the ingot was studied using a scanning electron microscope (SEM) and light microscope (LM). Secondly, the powders mixture was plasma sprayed on a cooled copper plate. The cross-section microstructure and the phase composition of the plasma spray deposit were analyzed with a transmission electron microscope (TEM), scanning electron microscope (SEM) and X-ray diffractometer (XRD). The thermal characteristics of the plasma sprayed deposit and the Ni-Si-B powder were analyzed using differential thermal analysis (DTA) and compared. The results show that the melted Ag and Ni-Si-B powders form immiscible liquids at high temperatures used both during arc-melting and plasma-spraying. The proved that that the plasma spraying enables production of a Ni-Si-B/Ag composite with high strength Ni-based matrix with dispersed in it fine soft Ag-FCC flake-like particles. [ABSTRACT FROM AUTHOR]

In this work, a mid infrared thermography was used to study thermal behavior of solid oxide fuel cell (SOFC) with a circular shape and a diameter of 90 mm. The emissivity of the anodic surface of the fuel cell was determined to be from 0.95 to 0.46 in the temperature range 550-1200 K and the profile and temperature distribution of the anodic surface of the unloaded cell was given. The surface temperature of the cell was determined during operation and the polarity changes from open circuit voltage (OCV) to 0.0 V. It was found that the cell self-heating effect decreases with increasing temperature of the cell. [ABSTRACT FROM AUTHOR]

The aim of this work was to investigate the possibility of obtaining an amorphous/crystalline composite starting from Ni-Si- B-based powder grade 1559-40 and silver powder. The alloy was produced using arc melting of 95% wt. Ni-Si-B-based powder (1559-40) and 5% wt. Ag powder. Ingot was re-melted on a copper plate and observed while cooling using a mid-wave infra-red camera. The alloy was then melt-spun in a helium atmosphere. The microstructure of the ingot as well as the melt-spun ribbon was studied using light microscopy and scanning electron microscopy with energy dispersive spectrometry. Phase identification was performed by means of X-ray diffraction. The observations confirmed an amorphous/crystalline microstructure of the ribbon where the predominant constituent of the microstructure was an amorphous phase enriched with Ni, Si, and B, while the minor constituent was an Ag-rich crystalline phase distributed in a film along the melt-spinning direction. [ABSTRACT FROM AUTHOR]

Abstract: A six-component Fe50Ni10Cu20P10Si5B5 immiscible alloy was arc-melt in argon and it was melt-spun from various temperatures. The morphology and chemical composition of the cross-section of the ingot and melt-spun ribbons were analysed with a scanning electron microscope SEM/EDS. The melt-spun ribbon was investigated by a transmission electron microscope (TEM). The melting range of the alloy was investigated by means of differential thermal analysis (DTA) and for reference, the temperature change during free cooling of the alloy was controlled by pyrometer in the melt spinning device. The slow cooling rate resulted in the fractal surface structures formed by the Fe-rich regions and Cu-rich regions typical for the alloying system with a miscibility gap. The structures of the melt-spun ribbons were dependent on ejection temperatures before the melt spinning. The lower ejection temperatures resulted in the formation of the structures separated into Fe-rich and Cu-rich regions. This was due to rapid cooling within the miscibility gap. Ejection at higher temperatures led to the formation of a uniform amorphous/crystalline composite. [ABSTRACT FROM AUTHOR]

A nickel–copper–iron–phosphorus Ni63Cu9Fe8P20 alloy was prepared. The precursors were induction melted in tubes under vacuum (10−2bar). The microstructure of the alloy was investigated by use of light microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS). Analysis of the morphology was carried out and the volume fraction of microstructural constituents in as-cast state was assessed. The melt spinning was used to produce ribbons from the alloy. The ribbons were then investigated by means of differential thermal analysis (DTA). High temperature X-ray studies of melt-spun ribbons as a function of temperature were carried out in order to characterize thermal stability of the alloy. The results were discussed and compared with other experimental data. [Copyright &y& Elsevier]

The aim of this study was to reveal the influence of the heat treatment after welding of 17-7PH (X7CrNiAl17-7) steel on the microstructure evolution and the texture of the welds. Microstructure investigation carried out by light microscopy and transmission electron microscopy showed that the austenite and δferrite coexist in as-welded condition. Annealing at the temperature range between 400 °C and 620 °C after welding causes small changes in the microstructure and the hardness of the welds increases. Heat treatment at 760 °C for 1 h resulted in the partial destabilization of the austenite. Aging after destabilization leads to tempering of the martensite: first the hardness increases and then decreases. The maximum hardness is observed when the ageing temperature reaches 510 °C. XRD studies confirmed the presence of the two phases: δ ferrite and austenite. Annealing at 400 °C/1 h and 550 °C/1 h results in changes of the intensities for individual peaks derived from austenite and ferrite. The calculated ratios of peak intensity were compared with the intensities of the reference sample. The differences in intensities suggested strong texture of the material. [ABSTRACT FROM AUTHOR]

This work presents a study of the microstructure formed in a liquid immiscible Fe 60 Cu 20 P 10 Si 5 B 5 alloy during moderate cooling on a copper plate and melt-spinning. The alloy ingot was re-melted on a copper plate and observed while cooling using a mid-wave infra-red (MWIR) camera. The heating and cooling characteristics of the melt-spun ribbon were studied using differential scanning calorimetry (DSC). The morphology and chemical composition of the ingot as well as the melt-spun ribbon were analyzed using scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). The compositions of the ingot and the ribbon were investigated using X-ray diffraction (XRD). Mössbauer spectroscopic measurements showing the influence of adding Cu to the Fe–Si–P–B alloy were also analyzed. The IR images from the MWIR camera enabled direct observation and identification of the liquid state transformations of the alloy. The DSC trace of the melt-spun ribbon showed crystallization of the amorphous matrix and confirmed that high temperature transformations occurred when the alloy was in the liquid state. Observations of the microstructure of the ingot revealed crystalline surface fractal structures formed by the Fe-rich eutectic constituent and Cu-rich fcc spherical precipitates. The morphology of the precipitates indicated that the precipitates formed in the miscibility gap. The microstructure of the melt-spun ribbon is composed of an amorphous Fe-rich matrix and elongated Cu-rich fcc precipitates. The observations based on the study of the microstructure are supported by Mössbauer spectroscopy. [ABSTRACT FROM AUTHOR]

The purpose of the work was investigation of the final microstructure and properties of the melt-spun Ni–Fe–Cu–P–B, Ni–Fe–B, and Ni–Cu–P alloys ejected as uniform liquid from the standard single-chamber crucible and from the double-chamber crucible as flux composed of the two Ni–Fe–B and Ni–Cu–P liquids cooled on a copper roller before formation of a uniform mixture. The methods applied in this study for microstructural investigations include scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Mössbauer spectroscopy. Thermal stability of the melt-spun alloys was tested using differential scanning calorimetry (DSC) and tensile test were performed. The results of the investigations are described and discussed in terms of the unique features of the two component melt spinning (TCMS) amorphous microstructure. [ABSTRACT FROM AUTHOR]

The aim of this work was to investigate the features of microstructure, phase composition, mechanical properties, and thermal stability of the two-component melt-spun Ni55Fe20Cu5P10B10 alloy. The development of the microstructure after heating to elevated temperatures was studied using scanning electron microscope and in situ high temperature X-ray diffraction. The high-temperature behavior of the two-component melt-spun Ni55Fe20Cu5P10B10 alloy and Ni40Fe40B20, Ni70Cu10P20, and Ni55Fe20Cu5P10B10 alloys melt-spun from single-chamber crucible was investigated using differential scanning calorymetry at different heating rates and by dynamic mechanical thermal analysis. The results show that band-like microstructure of the composite alloy is stable even at 800 K, although coarsening of bands forming the microstructure of the ribbons is observed above 550 K. Plastic deformation is observed in the composite previously heated to temperatures of 600–650 K. The properties of the composite alloy are generally different than the properties obtained for the melt-spun alloy of the same average nominal composition produced traditionally. Additionally, the mechanical and the thermal properties in this composite are inherited from the amorphous state of alloys that are precursors for two-component melt spinning (TCMS) processing. [ABSTRACT FROM AUTHOR]