Search

This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifier is driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD $_{i}$ < 8%) under variation of the utility-line input voltage from 180 to 250  ${{V}}_{{\rm{rms}}}$. These experimental results demonstrate the feasibility of the proposed LED scheme. [ABSTRACT FROM AUTHOR]

A design of a Class-E inverter with only one inductor and one capacitor is presented. It is operated at the optimal operation mode for domestic cooker. The design principle is based on the zero-voltage derivative switching (ZVDS) of the Class-E inverter with a parallel load network, which is a parallel resonant equivalent circuit. An induction load characterization is obtained from a large-signal excitation test bench, which is the key to an accurate design of the induction cooker system. Consequently, the proposed scheme provides a more systematic, simple, accurate, and feasible solution than the conventional quasi-resonant inverter analysis based on series load network methodology. The derivative of the switch voltage is zero at the turn-on transition, and its absolute value is relatively small at the turn-off transition. Switching losses and noise are reduced. The parameters of the ZVDS Class-E inverter for the domestic induction cooker must be selected properly, and details of the design of the components of this Class-E inverter need to be addressed. A 1,200 W prototype is designed and evaluated to verify the validation of the proposed topology. [ABSTRACT FROM AUTHOR]

This study presents an energy management approach for a hybrid energy system comprised of a photovoltaic (PV) array and a polymer electrolyte membrane fuel cell (PEMFC). Two storage devices [a Li-ion battery module and a supercapacitor (SC) bank] are used in the proposed structure as a high-energy high-power density storage device. Multisegment converters for the PV, fuel cell (FC), battery, and SC are proposed for grid-independent applications. Nonlinear differential flatness-based fuzzy logic control for dc-bus voltage stabilization for power plant is investigated. To validate the control approach, a hardware system is realized with analog circuits for the PV, FC, battery, and SC current control loops (inner controller loops), and with numerical calculation (dSPACE) for the external energy control loop. Experimental results with small-scale devices [a PV array (800 W, 31 A), a PEMFC (1200 W, 46 A), a Li-ion battery module (11.6 Ah, 24 V), and an SC bank (100 F, 32 V)] demonstrate the excellent energy-management scheme during load cycles. [ABSTRACT FROM PUBLISHER]

An analysis and design of a single-stage electronic ballast with a dc-side Class-DE low-dv/dt resonant rectifier is studied in this paper to improve a poor power-factor and low line harmonic. The power-factor correction is achieved by utilize an output characteristics of a Class-DE rectifier, which is inserted between the front-end bridge rectifier and the bulk-filter capacitor. The design procedure is based on the principle of the Class-DE rectifier, which also ensures more accurate results and the proposed scheme provided a more systematic and feasible analysis methodology. The active switches can be operated under the soft-switching condition. By employing an electromagnetic interference filter after bridge rectifier, the standard-recovery diode for bridge rectifier can be employed, the cost can be reduced, the conduction angle of the bridge-rectifier diode current was increased, and low line harmonic distortion and a power factor near unity were achieved. The dc-side Class-DE rectifier is driven by a high-frequency current source, which is obtained from the square-wave output voltage of the Class-D series-parallel resonant inverter through an LC-series circuit. A prototype of the ballast, operating at an 84-kHz fixed frequency and a 220-V rms, 50-Hz line voltage, was utilized to drive a T8-36 W fluorescent lamp. The validity of this approach was confirmed by simulation and experimental results. [ABSTRACT FROM AUTHOR]

An analysis and design of a zero-current-switching (ZCS) Class-D current-source driven rectifier for the lighting applications is presented, which is one of the resonant rectifiers as a power-factor corrector to improve a poor power-factor and high line current harmonic of a single-stage converter. A high power-factor is achieved by the utilization of output characteristics of a Class-D ZCS rectifier, which is inserted between the front-end bridge rectifier and the bulk-filter capacitor. The conduction angle of the bridge rectifier diode current was increased and a low-line current harmonic and a power-factor near unity can be obtained. The design procedure is based on the principle of the Class-D ZCS rectifier, which also ensures more accurate results and the proposed scheme provides a high efficiency and a more systematic and feasible analysis methodology. The active switches can be operated under the soft-switching condition. The validity of this approach was confirmed by simulation and experimental results. [ABSTRACT FROM AUTHOR]

An analysis of the junction capacitance in resonant rectifiers which has a significant impact on the operating point of resonance circuits is studied in this paper, where the junction capacitance of the rectifier diode is to decrease the resonant current and output voltage in the circuit when compared with that in an ideal rectifier diode. This can be represented by a simplified series resonant equivalent circuit and a voltage transfer function versus the normalized operating frequency at varied values of the resonant capacitor. A low voltage to high voltage push-pull DC/DC resonant converter was used as a design example. The design procedure is based on the principle of the half bridge class-DE resonant rectifier, which ensures more accurate results. The proposed scheme provides a more systematic and feasible solution than the conventional resonant push-pull DC/DC converter analysis methodology. To increase circuit efficiency, the main switches and the rectifier diodes can be operated under the zero-voltage and zero-current switching conditions, respectively. In order to achieve this objective, the parameters of the DC/DC converter need to be designed properly. The details of the analysis and design of this DC/DC converter's components are described. A prototype was constructed with a 62-88 kHz variable switching frequency, a 12 VDC input voltage, a 380 VDC output voltage, and a rated output power of 150 W. The validity of this approach was confirmed by simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents the use of a novel, single-stage high-power-factor electronic ballast with a symmetrical class-DE low-dv/dt resonant rectifier as a power-factor corrector for fluorescent lamps. The power-factor correction is achieved by using a bridge rectifier to utilize the function of a symmetrical class-DE resonant rectifier. By employing this topology, the peak and ripple values of the input current are reduced, allowing for a reduced filter inductor volume of the EMI filter. Since the conduction angle of the bridge rectifier diode current was increased, a low-line current harmonic and a power factor near unity can be obtained. A prototype ballast, operating at an 84-kHz fixed frequency and a 220-Vrms, 50-Hz line input voltage, was utilized to drive a T8-36W fluorescent lamp. Experimental results are presented which verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents an analysis on the effect of a parasitic capacitance full-bridge class-D current source rectifier (FB-CDCSR) on a high step-up push–pull multiresonant converter (HSPPMRC). The proposed converter can provide high voltage for a 12 VDC battery using an isolated transformer and an FB-CDCSR. The main switches of the push–pull and diode full-bridge rectifier can be operated under a zero-current switching condition (ZCS). The advantages of this technique are that it uses a leakage inductance to achieve the ZCS for the power switch, and the leakage inductance and parasitic junction capacitance are used to design the secondary side of the resonant circuit. A prototype HSPPMRC was built and operated at 200 kHz fixed switching frequency, 340 VDC output voltage, and 250 W output power. In addition, the efficiency is equal to 96% at maximum load. Analysis of the effect of the parasitic junction capacitance on the full-bridge rectifier indicates that it has a significant impact on the operating point of the resonant tank and voltage. The proposed circuit design was verified via experimental results, which were found to be in agreement with the theoretical analysis. [ABSTRACT FROM AUTHOR]