Search

A 3D network capture substrate based on poly(lactic-co-glycolic acid) (PLGA) nanofibers was studied and successfully used for high-efficiency cancer cell capture. The arc-shaped glass micropillars were prepared by chemical wet etching and soft lithography. PLGA nanofibers were coupled with micropillars by electrospinning. Given the size effect of the microcolumn and PLGA nanofibers, a three-dimensional of micro-nanometer spatial network was prepared to form a network cell trapping substrate. After the modification of a specific anti-EpCAM antibody, MCF-7 cancer cells were captured successfully with a capture efficiency of 91%. Compared with the substrate composed of 2D nanofibers or nanoparticles, the developed 3D structure based on microcolumns and nanofibers had a greater contact probability between cells and the capture substrate, leading to a high capture efficiency. Cell capture based on this method can provide technical support for rare cells in peripheral blood detection, such as circulating tumor cells and circulating fetal nucleated red cells.

Abstract Background Due to the high transfer ability of cancer cell, cancer has been regarded as a world-wide high mortality disease. Quantitative analysis of circulating tumor cells (CTCs) can provide some valuable clinical information that is particularly critical for cancer diagnosis and treatment. Along with the rapid development of micro-/nano-fabrication technique, the three-dimensional (3D) bionic interface-based analysis method has become a hot research topic in the area of nanotechnology and life science. Micro-/nano-structure-based devices have been identified as being one of the easiest and most effective techniques for CTCs capture applications. Methods We demonstrated an electrospun nanofibers-deposited nickel (Ni) micropillars-based cytosensor for electrochemical detection of CTCs. Breast cancer cell line with rich EpCAM expression (MCF7) were selected as model CTCs. The ultra-long poly (lactic-co-glycolic acid) (PLGA) nanofibers were firstly-crosswise stacked onto the surface of Ni micropillars by electrospinning to construct a 3D bionic interface for capturing EpCAM-expressing CTCs, following immuno-recognition with quantum dots functionalized anti-EpCAM antibody (QDs-Ab) and forming immunocomplexes on the micro-/nano-chip. Results The Ni micropillars in the longitudinal direction not only play a certain electrical conductivity in the electrochemical detection, but also its special structure improves the efficiency of cell capture. The cross-aligned nanofibers could simulate the extracellular matrix to provide a good microenvironment which is better for cell adhesion and physiological functions. Bioprobe containing quantum dots will release Cd2+ in the process of acid dissolution, resulting in a change in current. Beneath favourable conditions, the suggested 3D cytosensor demonstrated high sensitivity with a broad range of 101–105 cells mL−1 and a detection limit of 8 cells mL−1. Conclusions We constructed a novel 3D electrochemical cytosensor based on Ni micropillars, PLGA electrospun nanofibers and quantum dots bioprobe, which could be used to highly sensitive and selective analysis of CTCs. More significantly, the 3D cytosensor can efficiently identify CTCs from whole blood, which suggested the potential applications of our technique for the clinical diagnosis and therapeutic monitoring of cancers.

This paper presents a total phosphorus online real-time monitoring system integrated with on-chip digestion based on the merits of optofluidic technology. The integrated optofluidic device contains a hollow optical fiber employed for pretreatment and digestion of phosphorus solution samples, a polydimethylsiloxane (PDMS)-based micromixer with convergent–divergent walls designed to enable sufficient mixing and chromogenic reaction, and a couple of optical fiber collimators attached with a Z-shaped flow cell for optical detection. Details of system design and fabrication are introduced in this paper. In the experiment, on-chip digestion of four typical phosphates in aqueous solution including organophosphorus and inorganic phosphorus is investigated under different reaction conditions, such as digestion temperature, concentration of oxidant and pH value, and the optimal reaction parameters are explored under different conditions. Meanwhile, we demonstrate the online real-time monitoring function of the optofluidic device, and the digestion mechanisms of four different phosphates are analyzed and discussed. Compared with the national standard method, we find that the measurement accuracy and sensitivity are acceptable when the concentration of total phosphorus is between 0.005–0.9 mg/L (by weight of P) in aqueous solution, which covers the range defined in the national standard. The traditional digestion time of several hours is greatly reduced to less than 10 s, and the content of total phosphorus can be obtained in a few minutes. The integrated optofluidic device can significantly shorten the test time and reduce the sample amount, and also provides a versatile platform for the real-time detection and analysis of many biochemical samples.

Contact electrification between water and a solid surface is crucial for physicochemical processes at water-solid interfaces. However, the nature of the involved processes remains poorly understood, especially in the initial stage of the interface formation. Here we report that H2O2 is spontaneously produced from the hydroxyl groups on the solid surface when contact occurred. The density of hydroxyl groups affects the H2O2 yield. The participation of hydroxyl groups in H2O2 generation is confirmed by mass spectrometric detection of 18O in the product of the reaction between 4-carboxyphenylboronic acid and 18O-labeled H2O2 resulting from 18O2 plasma treatment of the surface. We propose a model for H2O2 generation based on recombination of the hydroxyl radicals produced from the surface hydroxyl groups in the water-solid contact process. Our observations show that the spontaneous generation of H2O2 is universal on the surfaces of soil and atmospheric fine particles in a humid environment. [ABSTRACT FROM AUTHOR]

Here is reported a fluorescent biosensor for glucose detection based on water-soluble and pH-responsive silicon nanodots. The silicon nanodots were prepared using a facile hydrothermal method. The advantages of using the silicon nanodots as glucose sensor are twofold. Firstly, the fluorescence of silicon nanodots was quenched by hydrogen peroxide that was produced from glucose oxidation. Secondly, the fluorescence of silicon nanodots was highly sensitive to gluconic acid that was also produced by glucose oxidation. Our results show that this method detected glucose as low as 0.54 μM with a good selectivity and allowed the determination of glucose in serum samples. This method is also simple, rapid, low-toxic and low-cost, thereby hold high application potential for biological assays. [ABSTRACT FROM AUTHOR]

Using PEGylated nanoparticles and light-sensitive azobenzenes, a multicolor fluorescence layer-by-layer film loading drug has been constructed basedon hydrogen bonding. The multilayer film exhibited multi-responsive drug release properties. [ABSTRACT FROM AUTHOR]

Nanomotors represent a significant step forward in nanotechnology, and prove that nanotubes and other nanostructures several hundred times smaller than the diameter of a human hair can be manipulated and assembled into true devices. In this letter, nanotubes based nanomotors are reported. The nanomotors were observed to move at a velocity of ∼0.5 m/s, which is several orders of magnitude faster than current nanomotors. Concentration difference energy was thought to provide the main motive forces to drive these nanomotors. This phenomenon which is seldom observed at macroscopic scale, is common in microscale, and can be employed to explain some motions of nano- and microscale objects. [ABSTRACT FROM AUTHOR]