Search

Summary: This paper suggests a nonisolated noncoupled inductor‐based topology for direct current (DC)–DC converters for DC microgrids. The proposed configuration profits from advantages like high step‐up capability, continuous input current, simple structure, reduced normalized standing voltage (NSV) on switches/diodes, large gain per devices, common ground point between source‐load, and maximum power point tracking (MPPT) capability. Both the switches (T1, T2) are turned on/off simultaneously, which minimizes the number of operational modes and simplifies the control strategy. These properties lead to a more compact, less expensive, and lighter topology. The operational modes and steady‐state analysis as well as design considerations have been presented in detail. According to comparative analysis, the voltage conversion ratio per number of devices in suggested topology is higher than that of other similar topologies addressed in literature. The simulation results extracted from PSCAD/EMTDC software and the experimental outcomes obtained from laboratory‐scale prototype confirm the effectiveness and correct performance of proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

Cascaded multilevel inverters (MLIs) have been proposed that utilise transformers in the basic unit. The proposed inverters primarily serve to step up the input voltages in addition to using lower number of components in comparison to traditional MLIs. In order to generate all voltage levels (even and odd) at the output, three different algorithms are proposed to determine the magnitude of DC voltage sources and transformer turn ratios. Also, the basic inverter unit was further developed and two new flexible MLI structures have been obtained. The developed structures increase the input voltage with no need for an additional boost converter. A reduction in the number of power switches, the peak inverse voltage, and the number of DC voltage sources are other advantages of the proposed topologies. Also, a simple cost model was developed and the dimensionless cost coefficient was determined. The overall cost of the proposed MLIs was compared to the similar MLIs from the literature. It was shown that the proposed MLI decrease the overall cost of the system if the cost coefficient is selected appropriately. To verify the performance of the proposed topologies simulated by the mathematical model; several lab-scale inverters were built and tested and good agreement was achieved. [ABSTRACT FROM AUTHOR]

A new three-phase hybrid multilevel inverter configuration is proposed. The proposed inverter is modular and consists of three single-phase H-bridge inverters, one three-phase H-bridge inverter and auxiliary modules for increasing the number of output voltage levels. The performance of the proposed inverter has been compared with some of the commonly used inverters within the literature in terms of the number of components, blocking voltage and overall losses. The proposed multilevel inverter has lower number of insulated-gate bipolar transistors and gate drivers and subsequently requires a relatively simple control strategy for generating the desired output voltage. Finally, the performance of the proposed inverter has been validated via a laboratory-scale prototype along with numerical simulation. [ABSTRACT FROM AUTHOR]

Multilevel inverters generate high-level voltage with high quality and low-harmonic distortion, and these unique properties have increased their applications in renewable energy sources. However, these inverters require several passive components and a complex pulse width modulation (PWM) control method. Besides, they suffer from voltage balancing problems. In this work, a new inverter has proposed that generates seven-level voltage from one DC source by reduced number of switches which does not exhibit any voltage balancing problem. The proposed inverter without any extra boost circuit is able to increase the input voltage. The voltage stress on all the switches in the proposed inverter is the same. In this study, variable amplitude phase disposition PWM control method that is compatible with the proposed inverter is developed. Moreover, extended structure of the proposed inverter and its new algorithm in generating all odd and even voltage levels are proposed. To validate the performance of the inverter, a prototype has been built and tested and also its performance has been modelled using PSCAD/EMTDC software package. Very good agreement has been achieved between experimental results and simulations. [ABSTRACT FROM AUTHOR]