Search

In this study, porous activated carbon was produced from coffee waste and used as an effective adsorbent for the removal of humic acid (HA) from seawater and methyl orange (MO) dye from aqueous solutions. Phosphoric acid H3PO4 was used as an activating agent for the chemical activation of these agricultural wastes. The characterization of the activated carbon obtained using a scanning electron microscope (SEM), Fourier-transform infrared (FTIR) spectroscopy analysis, X-ray diffraction (XRD) and the Brunauer–Emmett–Teller (BET) method revealed that the activated carbon products exhibited high porosity and the formation of various functional groups. The effects of different parameters were examined using batch adsorption experiments, such as the adsorbent masses, pH, initial pollutant concentration and contact time. The results show that the performance increased with an increased adsorbent mass (up to 0.25 g/L) and decreased initial concentration of the adsorbent tested. On the other hand, this study clearly showed that the adsorption efficiency of the MO on the raw spent coffee grounds (SCGs) waste was around 43%, while no removal was observed for the humic acid. The experiments demonstrated that the activated carbon synthesized from the used coffee grounds (the efficiency was compared with commercial activated carbon (CAC) with a difference of 13%) was a promising alternative to commercially available adsorbents for the removal of humic acid from seawater. To understand and elucidate the adsorption mechanism, various isothermal and kinetic models were studied. The adsorption capacity was analyzed by fitting experimental data to these models. The experimental data for methyl orange dyes were analyzed using Langmuir and Freundlich isothermal models. The Freundlich isotherm model provided a superior fit to the equilibrium data, as indicated by a higher correlation coefficient (R2) than that of the Langmuir model. The maximum adsorption was observed at pH 3. The Freundlich adsorption capacity was found to be 333 mg/g adsorbent. The PAC showed a high adsorption capacity for the MO and HA. The PAC showed the highest adsorption capacities for the HA and MO compared with the other adsorbents used (SCGs and CAC) and would be a good material to increase the adsorption efficiency for humic acid removal in the seawater pretreatment process. In addition, the prepared AC BET surface area was 520.40 m2/g, suggesting a high adsorption capacity. This makes the material potentially suitable for various applications that require a high surface area. These results indicate that high-quality sustainable activated carbon can be efficiently produced from coffee waste, making it suitable for a wide range of adsorbent applications targeting various pollutants. [ABSTRACT FROM AUTHOR]

In recent years, reverse osmosis water desalination has developed rapidly and has become the most competitive and widely used technology in the world. The number of desalination plants is increasing rapidly as freshwater needs increase. Various membrane technologies have been developed and improved, including nanofiltration (NF) and reverse osmosis (RO), whose desalination costs have been relatively reduced. Therefore, this work proposes an experimental study for a small desalination unit based on RO generated by renewable energy, which is mainly suitable for arid regions or desert areas that do not have electricity and water and can be applied for emergency treatment to meet strong freshwater resource needs. In this study, to meet the drinking water demand, a reverse osmosis desalination system is designed and evaluated in order to improve and optimize its operation. This system has a daily capacity of 2 m3. We used brackish groundwater, which has been characterized as reference water, to produce synthetic water for different salinities until seawater. The analysis is based on data obtained from experiments carried out in the standalone RO pilot designed for the production of fresh water. For this purpose, we conducted relevant experiments to examine the influence of applied pressure, salt concentration and temperature on the RO membrane performance. The effects of different factors that affect the energy consumption in the RO desalination process were analyzed, and those with significant influence were explored. The effectiveness of RO desalination coupled with a photovoltaic (PV) energy system is shown. We found the recovery rate for system operation to be 32%. An optimization study is presented for the operation of an autonomous RO desalination system powered by photovoltaic panels. The energy produced by the PV system was used to feed two pumps forthe production of drinking waterwithanRO membrane, under the conditions of the town of Bou-Ismail. As results, a 3 kWp PV system was installed based on the energy demand. The design data have shown that a 3 kWp PV system can power a 1.8 W RO load given the Bou-Ismail climate. Energy consumption in the case study under Bou-Ismail weather conditions were analyzed. The desalination of brackish water at a TDS value of 5 g/L requires an energy of about 1.5 kWh/m3. Using seawater at a TDS value of 35 g/L, this value increases to 5.6 kWh/m3. The results showed that the optimal recovery rate for system operation was determined to be 32% for a feedwater salinity of 35 g/L, and 80% for a feedwater salinity of 1 g/L. [ABSTRACT FROM AUTHOR]

The main purpose of this study was to improve sand filtration process by using local media and optimizing to obtain the best operating parameters. Sand from the Algerian desert was utilized. The treatment effectiveness on domestic effluent was assessed by monitoring pollution parameters such as turbidity, chemical oxygen demand (COD) and biological oxygen demand (BOD). The results of showed that the sand had a homogenous structure with a large presence of angular and blunted grains and a low percentage in round grains. This characteristic improves the filtration efficiency. The results showed also that the abatement rates of pollution indicators such as turbidity, COD and BOD were high for all experiments, between 60% and 90%. The sand filter designed in this study demonstrated a great performance for the treatment of domestic wastewater. [ABSTRACT FROM AUTHOR]

The main objective of this study was to demonstrate the efficiency and to optimize the operating conditions of photodegradation of paracetamol in the presence of suspended titanium dioxide catalyst in a photoreactor. An experimental design study was carried out using central composite design modelling. Optimization was applied to the tubular reactor under fixed photonic flux with radiation from two 24-watt UV-A lamps. The optimal values of the operating parameters were found to be pH of 7.288, TiO2 concentration of 0.9932 g·L-1 and paracetamol initial concentration of 15 mg·L-1. The paracetamol degradation rate approached 98.46% under optimal conditions. Modelling of the system led to a second-degree polynomial. Regression analysis gave an R² value of 0.977 which meant good agreement between the experimental results and the predicted values. An interaction was demonstrated between the catalyst and the operating parameters (pH, CPara and CTiO2) as well as between the model pollutant concentration and the pH had an insignificant effect on the yield compared to that of the quantity of the catalyst and the initial pollutant concentration. [ABSTRACT FROM AUTHOR]

The purpose of this study is to optimize the operating conditions in batch mode using Box‐Behnken Design (BBD), for the coagulation‐flocculation line sizing prior the sand filter in the pilot scale. Three coagulants were employed to achieve a high turbidity removal with a low concentration of residual metals. The results showed that the best turbidity removal was obtained with FeCl3. Using BBD (15 experiments), the optimal parameters were: coagulant dose = 5.5 mg FeCl3/L, slow stirring time = 33 min and slow stirring velocity = 45 rpm, in these conditions, the turbidity removal reached 94.89% and the residual iron concentration was 0.449 mg/L. Regarding the model fit, the obtained R2 values were 99.67% for turbidity removal and 99.47% for residual iron concentration. The optimum conditions obtained from this study could be scaled up and applied to desalination plants. BBD approach is of great interest because it allows the prediction of the response value without performing experiments. [ABSTRACT FROM AUTHOR]

The fixed bed reactor was combined with a solar photoreactor and UV lamp reactor. This hybrid photoreactor used a heterogeneous photocatalysis process (TiO 2 /UV) as a tertiary treatment for the degradation of tartrazine dye in water. The solar reactor removed almost all organic compounds from the wastewater. Photocatalysis was optimized using a parametric study to improve the influence of different parameters on the degradation efficiency. Color removals when using solar, UV lamp and hybrid reactors present 99%, 30%, and 99%, respectively. Tartrazine removal kinetics followed a pseudo-first order model. The hybrid solar and UV lamp system combination was a feasibility choice for removing both dyes from wastewater. [ABSTRACT FROM AUTHOR]

In sustainable development context, solar energy may be adapted to improve the development of green technologies in wastewater treatment. In this paper, the photocatalytic elimination of Methylene Blue (MB) as a reference dye is performed in a fixed bed photoreactor. A commercial TiO2 catalyst is immobilized on a cement support irradiated by solar light. The effects of some parameters such as the light source, pH of the solution as well as the pollutant initial concentration were investigated. The results show that the quantity of catalyst affects positively the MB degradation rate unlike the pollutant initial concentration which decreases the degradation efficiency. The degradation efficiency was found higher at around basic pH values (93%-97%). In addition, the degradation rate of pollutant was higher with solar light irradiation (97%) rather than with artificial irradiation (16%). This solar photocatalytic device is a potential application for organic dyes elimination. [ABSTRACT FROM AUTHOR]

The methodology of experimental research was carried out using the MODDE 6.0 software to study the acetamiprid photodegradation depending on the operating parameters, such as the initial concentration of acetamiprid, concentration and type of the used catalyst and the initial pH of the medium. The results showed the importance of the pollutant concentration effect on the acetamiprid degradation rate. On the other hand, the amount and type of the used catalyst have a considerable influence on the elimination kinetics of this pollutant. The degradation of acetamiprid as an environmental pesticide pollutant via UV irradiation in the presence of titanium dioxide was assessed and optimized using response surface methodology with a D-optimal design. The acetamiprid degradation ratio was found to be sensitive to the different studied factors. The maximum value of discoloration under the optimum operating conditions was determined to be 99% after 300 min of UV irradiation. [ABSTRACT FROM AUTHOR]

The feasibility of the application of the Photo-Fenton process in the treatment of aqueous solution contaminated by Tylosin antibiotic was evaluated. The Response Surface Methodology (RSM) based on Central Composite Design (CCD) was used to evaluate and optimize the effect of hydrogen peroxide, ferrous ion concentration and initial pH as independent variables on the total organic carbon (TOC) removal as the response function. The interaction effects and optimal parameters were obtained by using MODDE software. The significance of the independent variables and their interactions was tested by means of analysis of variance (ANOVA) with a 95% confidence level. Results show that the concentration of the ferrous ion and pH were the main parameters affecting TOC removal, while peroxide concentration had a slight effect on the reaction. The optimum operating conditions to achieve maximum TOC removal were determined. The model prediction for maximum TOC removal was compared to the experimental result at optimal operating conditions. A good agreement between the model prediction and experimental results confirms the soundness of the developed model. [ABSTRACT FROM AUTHOR]

The non-biodegradability of textile wastewater is mainly due to the presence of synthetic dyes. Resistance to bacterial degradation led to the development of new techniques where solar photocatalysis appears to be the best method for this type of application. methylene blue (MB) degradation was studied in TiO2and ZnO aqueous suspension using solar energy in a tubular reactor. This study was conducted to evaluate the performance of the prototype and explore the feasibility of this concept for solar photocatalytic oxidation. The main objective of this work was to compare the efficiency of two types of catalysts, which are titanium dioxide (TiO2) and zinc oxide (ZnO). The use of TiO2as a catalyst enables a good degradation of MB which can achieve a disposal rate of 98% after 270 min with a TiO2concentration of 0.75 g/L. The same removal rate can be achieved by ZnO but for a much smaller concentration which was 0.025 g/L after 140 min. [ABSTRACT FROM AUTHOR]