Search

This paper presents a new six-level flying capacitor based (FC-based) multilevel converter with one dc source and the capability of operating in all power factors and modulation indexes. Multilevel converters with one dc voltage source are attractive in many applications as they do not need rather expensive and bulky multiwinding input transformer connection at the dc side. On the other hand, not all classic multilevel converters with one dc source can produce any desirable number of output voltage levels at all power factors and/or modulation indexes. In this paper, a hybrid structure is proposed in which six voltage levels can be realized at the ac terminals. The modulation technique and the control strategy for the FC voltage balancing are presented. To show the advantages of the proposed converter, different performance criteria, such as switch count and rating, the size of capacitors, switching frequency, and power losses, are compared with other existing six-level topologies. The results indicate that the proposed structure is superior to other six-level converters from different standpoints. Simulation results are used to further evaluate the performance of the proposed converter. A laboratory-type experimental setup is used to validate the theoretical results. [ABSTRACT FROM AUTHOR]

Due to the development of integrated electronic appliances, independently controlled multiple-output dc–dc converter prototypes have started to emerge in various forms, offering advantages of more compact size and cheaper cost. However, the existing converter topologies are capable of regulating outputs only with the help of auxiliary converter circuits and additional switches. The converter also fails to control all of the outputs independently when the converter has a greater number of output stages than that of the peripheral switching/linear regulators. Therefore, in this paper, a novel dc–dc converter prototype is proposed that can be utilized to construct independently controlled multiple-output converter topology with a single PWM signal driving the primary inverter switches. Feasibility, design challenges, and practical considerations are discussed in this paper with a design example of an independently controlled four-output, 356-W resonant converter system. [ABSTRACT FROM AUTHOR]

This paper proposes a multilevel series compensator (MSC) to deal with voltage sags/swells, harmonic compensation, or reactive power compensation. Such a device can be considered as a dynamic voltage restorer or a series active power filter (Series-APF). The MSC can improve the power quality of loads located in stiff systems. The configuration is based on three-phase bridge (TPB) converters connected by means of cascaded single-phase transformers. This arrangement permits the use of a single dc-link. A generalization for $K$ -stages in which $K$ -transformers are coupled with $K$-TPB converters is presented. The topology permits generating a high number of levels in the voltage waveforms with a low number of power switches in comparison with a classic topology. The multilevel waveforms are generated by the converters through a suitable pulsewidth modulation (PWM) strategy that takes into consideration the transformer turns ratios. Modularity and simple maintenance make the proposed MSC an attractive solution compared with some conventional configurations. Model, PWM strategy, and overall control are discussed in this paper. Simulation and experimental results are presented as well. [ABSTRACT FROM PUBLISHER]

Pulse-width-modulated (PWM) converters have been widely applied for power processing, and they are typically the stems of other types of converters, such as quasi-resonant, Z-source, and switched-inductor hybrid converters. Development of PWM converters has been spanning over a century, starting from the buck converter. The well-known PWM converters include buck, boost, buck–boost, Ćuk, single ended primary inductive converter (SEPIC), zeta, Z-source, quasi-Z source, etc. Many attempts have been proposed to develop these converters based mostly on canonical cell concepts and by introducing extra LC filters to the cells. This paper presents an enhancement to the layer and graft schemes by introducing the ideas of dc voltage/current offsetting, capacitor/inductor component splitting, diode grafting, and inverse operation of PWM converters. The PWM converters, which can be operated in continuous conduction mode (CCM) or discontinuous conduction mode (DCM), therefore can be synthesized systematically according to decoded transfer gains. Decoding and synthesizing PWM converters uniquely bridge transfer gains to converter topologies and provide readers a comprehensive understanding of PWM-converter evolution from the original converter, the buck converter. Additionally, in this paper, the Ćuk, SEPIC, and zeta converters all with the same transfer gain of $D/(1 - D)$ are proved to be equivalent to the buck–boost converter with an extra LC filter. For further illustrating the proposed approaches, various types of Z-source converters, switched-capacitor/switched-inductor hybrid converters, and a single-stage interleaved converter are reviewed, and new PWM converters are developed. [ABSTRACT FROM AUTHOR]

In this paper, three generalized configurations of three-phase pulsewidth modulated (PWM) rectifiers are presented. They are composed of cascaded cells, each formed by a three-phase bridge of switching devices and a three-phase transformer to cascade the cells and isolate the load from the power source. One configuration is bidirectional, whereas the other two are unidirectional alternatives that replace power switches for diodes in some legs. The turns ratios of transformers from each cell are designed in order to provide the required gain and number of levels in the inverted multilevel voltage, enhancing power quality while attending requirements for proper operation in each case. Configurations with two and three cells are compared by means of simulations between themselves and with three conventional three-phase PWM rectifiers: the two-level insulated gate bipolar transistor bridge and the multilevel neutral point clamped (NPC) bridge and NPC H-bridge. Many degrees of asymmetry between the transformers in each cell, determined by the turns ratios, are considered to evaluate their impact on the topologies with relation to performance and cost. It is shown that proposed multilevel rectifiers present lower harmonic distortion, semiconductor losses, and switching stress, and some options with intermediate asymmetry are considered as good alternatives to the most asymmetrical cases. Experimental results are also provided for configurations with two cells, to demonstrate their lower harmonic distortion and power losses compared to the conventional isolated two-level PWM rectifier. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-phase multicell converter for ac–dc power conversion, which is formed by a series connection of several full-bridge converter stages through passive components. The proposed topology employs a simple control scheme based on the carrier-based sinusoidal pulsewidth modulation technique. Detailed design procedure of the passive filter components are analyzed and discussed. An efficient optimization method based on a differential evolution algorithm is utilized to optimize the filter parameters. Considering the filter structure, active damping is introduced in the control scheme to improve the stability of the overall system, which is later verified by experiments. The systematic design approach of the controller parameter is also highlighted, focusing a specific set of goals. Experimental results for a 1-kW prototype are presented to further validate the concept. [ABSTRACT FROM AUTHOR]

A cascaded H-bridge (CHB) converter-based medium or high-voltage motor drive system, that consists of three single-phase CHB chains, may suffer a severe second-harmonic ripple power issue. Oversizing dc capacitors and using active power decoupling control with additional active or passive components are the two possible ways to address this issue, but this is achieved at the expense of increased system cost and complexity. This paper proposes a power decoupling control to tackle this issue without using any extra components for regenerative CHB-based converters. By introducing a set of negative-sequence decoupling currents to the front-end pulsewidth-modulated rectifier of each submodule, the second-harmonic ripple power can be removed from the submodule dc capacitors, and all the ripple power in the transformer core legs can be counteracted without affecting the magnetic flux and the grid current. The decoupling current is derived from the input and output measurements of the CHB converter. It gives the minimal increase of the modulation index and has no impacts on the input and output power quality. The effectiveness of the proposed control is verified in simulations and a 72-kW experimental prototype. [ABSTRACT FROM AUTHOR]

Hybrid boost converter (HBC) has been proposed to replace a dc/dc boost converter and a dc/ac converter to reduce conversion stages and switching loss. In this paper, control of a three-phase HBC in a Photovoltaic (PV) charging station is designed and tested. This HBC interfaces a PV system, a dc system with a hybrid plug-in electrical vehicles, and a three-phase ac grid. The control of the HBC is designed to realize maximum power point tracking for PV, dc bus voltage regulation, and ac voltage or reactive power regulation. A testbed with power electronics switching details is built in MATLAB/SimPowersystems for validation. Simulation results demonstrate the feasibility of the designed control architecture. Finally, lab experimental testing is conducted to demonstrate HBC's control performance. [ABSTRACT FROM AUTHOR]

This paper investigates power shunt filter topologies composed of three standard three-leg converters applied in either three or four-wire system. Compared with the usual three-phase shunt filter, the proposed ones allow us to reduce dc-link voltages, harmonic distortion or/and the semiconductor losses, and fault tolerant operation. Suitable control strategies to adjust filter and circulating currents, as well as the three dc-link voltages are presented. Two pulse-width modulation techniques are developed for the proposed topologies in order to achieve the best voltage-pulse pattern. Comparisons between these techniques are carried out in this paper. Simulation and experimental results are presented to validate the theoretical approach. [ABSTRACT FROM PUBLISHER]

This paper proposes a modular isolated dc–dc converter, based on the input-series and output-series association of the full-bridge PWM dc–dc converter with capacitive filter. The main attribute of the proposed architecture is its ability to provide self-balance of the input and output voltages across the individual converters, without voltage loop control scheme, both in the steady-state and transient operations. Circuit operation, theoretical analysis, and modeling are included in this paper, along with experimental results taken from a laboratory prototype with four modules, 1600-Vdc total input voltage, 1600-Vdc total output voltage, 4-kW output power, and 40-kHz switching frequency. Possible applications include high-voltage power supplies, solid-state transformers, dc current distribution systems, and renewable electric energy systems. [ABSTRACT FROM PUBLISHER]

This paper proposes a solution for reducing the ground leakage current in transformerless single-phase grid-connected photovoltaic converters. This is obtained with the introduction of an active common-mode filter able to compensate for variations of the output common-mode voltage of the power converter. The active common-mode filter is applied to a widespread and efficient full-bridge driven by a three-level pulse width modulation, allowing the power converter to operate with low ground leakage current and with an arbitrary power factor. After showing the desired voltage waveform for common-mode voltage compensation, this paper presents the design guidelines for the needed additional magnetic component together with the power loss considerations for all the devices added for the proposed solution. Experimental results show the performance of the proposed solution in terms of ground leakage current reduction, effectiveness of dead-time compensation, total harmonic distortion of the injected grid current, and power losses. [ABSTRACT FROM PUBLISHER]

Microgrid-interactive converters are increasingly expected to provide auxiliary services, particularly during islanded microgrid operation. Unbalanced, non-sinusoidal pulse width modulation (PWM) references may be required when converters provide auxiliary services, such as negative-sequence compensation. Since PWM references cannot exceed dc-bus voltage defined limits without causing overmodulation, the maximum positive-sequence voltage producible by microgrid-interactive converters may be diminished unless reference waveforms are adjusted. In this paper, a technique for maximizing the linear modulation region by injecting a common mode component into PWM references is proposed for microgrid-interactive cascaded H-bridge (CHB) converters. The technique presented can be implemented in real-time without lookup tables, is controller independent, is compatible with any carrier-based PWM method, enabling its use for symmetric and asymmetric CHB, and enables continued operation after internal fault events when utilized with fault tolerant PWM schemes. Experimental data verify the common mode injection technique. [ABSTRACT FROM PUBLISHER]

The noninverting buck–boost converter has attracted significant attention in the photovoltaic (PV) module integrated application, as it offers high efficiency while maintaining a low cost and a simple topology. When this converter is employed, special care must be taken at the transition between buck and boost operating modes, as a dead-zone in the voltage transfer function can cause abrupt perturbations in the controlled voltage, decreasing the regulation quality and ultimately lowering the power conversion efficiency. In this paper, a new dead-zone compensation technique is proposed with the scope of smoothing the transition between operating modes, eliminating the voltage ripple and improving the regulation performance, while maintaining high efficiency. The converter under analysis is studied together with its gate driving circuit, which is based on a bootstrap capacitor power supply for the high-side switches. The proposed dead-zone compensation technique is deduced by using the principle of maintaining the ideal voltage gain function across the converter operating range. The technique is analyzed, implemented and tested on a purposely built PV module integrated noninverting buck–boost converter. The experiments reveal a sensible improvement of the voltage regulation during mode transition, confirming the effectiveness of the proposed technique and its fitness for the PV application. [ABSTRACT FROM AUTHOR]

Five-level hybrid-clamped (5L-HC) converter is a newly proposed topology which is suitable for high-performance medium-voltage high-power conversions without switches directly connected in series. The critical issue of this converter is that two flying capacitor voltages of each phase and two neutral-point potentials of the dc-link need to be balanced. This paper presents a decoupled voltage balancing method for this 5L-HC converter based on modified phase-shifted pulse width modulation (PS-PWM) and optimal zero-sequence voltage injection. The voltages across the central dc-link capacitor and two flying capacitors are balanced first by adjusting the width of four PWM signals. Second, the relationship between the neutral-point currents and the output phase voltage is studied and the upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection. Both steady-state and dynamic-state simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

Medium-voltage drives are regularly used in the petrochemical industry. These drives often vary in topology, semiconductor design, and principles of operation. They each have their own merits, not only in terms of structure, design, and reliability, but also with regard to suitability to specific applications. This paper presents a technology overview of commercially available medium-voltage drive topologies with a view on how they match to petrochemical applications. The operating and performance characteristics of each drive topology are reviewed while manufacturer-specific implementation details are excluded. Common industry and application requirements such as harmonics, motor compatibility, regeneration capability, dynamic performance, and robustness to system power disturbances are used as comparison criteria. Application aspects such as commissioning and operation challenges are highlighted from a practical point of view. [ABSTRACT FROM AUTHOR]

This paper addresses the inverter nonlinearity of a three-level T-type inverter. The main causes of the nonlinearity are pulse shaping, pulse skipping due to narrow pulses for the dead time, and voltage drop of the switching devices. Although the same causes have existed in two-level inverters, the pulse skipping phenomenon and results are quite different in the case of the three-level T-type inverter. The effects of pulse shaping and skipping have been investigated and discussed. In addition, the voltage drop of the switching devices has been considered in conjunction with the conduction path of the T-type inverter. Compensation methods based on the pulse width modulation (PWM) of T-type inverter to alleviate the inverter nonlinearity have been proposed from research results. The proposed methods could be easily implemented by adding appropriate offset voltages to the voltage references of the inverter in PWM. Furthermore, a neutral voltage balancing method of a three-level T-type inverter has been proposed in conjunction with the proposed PWM methods using offset voltage. Through extensive experimental tests, the fifth- and seventh-harmonic components of the current are conspicuously reduced along with the even harmonics. The neutral voltage of the inverter can be balanced effectively with the proposed offset voltage adjustments as well. [ABSTRACT FROM AUTHOR]

Multilevel cascaded H-bridge converters have become a mature technology for applications where high-power medium ac voltages are required. Normal operation of multilevel cascaded H-bridge converters assumes that all power cells have the same dc voltage, and each power cell generates the same voltage averaged over a sampling period using a conventional phase-shifted pulse width modulation (PWM) technique. However, this modulation method does not achieve good results under unbalanced operation per H-bridge in the power converter, which may happen in grid-connected applications such as photovoltaic or battery energy storage systems. In the paper, a simplified mathematical analysis of the phase-shifted PWM technique is presented. In addition, a modification of this conventional modulation method using variable shift angles between the power cells is introduced. This modification leads to the elimination of harmonic distortion of low-order harmonics due to the switching (triangular carrier frequency and its multiples) even under unbalanced operational conditions. The analysis is particularized for a three-cell cascaded H-bridge converter, and experimental results are presented to demonstrate the good performance of the proposed modulation method. [ABSTRACT FROM PUBLISHER]

In an asymmetrical pulse-width-modulated half-bridge (APWM HB) series resonant converter, an auxiliary LC network is provided for ensuring zero-voltage switching (ZVS) over a wide range of line and load variations. However, it comes at the cost of increased number of components and reduced efficiency and reliability. This paper presents a novel design methodology for the standard APWM HB resonant topology, which uses the magnetizing current and eliminates the need for extra components. The converter with the proposed design methodology operates at the resonant frequency of the tank and features load-independent ZVS for a wide range of input voltage variation with minimal magnetizing current. Empirical formulae are derived to design the resonant network and the magnetizing inductance of the high-frequency transformer systematically in a flowchart-based manner. The proposed design is validated by using simulations as well as experiments and is compared with a reference APWM HB series resonant converter design that uses an auxiliary LC circuit for ZVS. Two separate experimental prototypes of the two converters rated for 30 W, 48 V/5 V with a switching frequency of 500 kHz were built and tested in the laboratory. It was found that the converter with the proposed design methodology, apart from having lower component count, is about 3% more efficient than the reference topology at the rated power. [ABSTRACT FROM PUBLISHER]

A two-switch semiquadratic fifth-order buck converter belonging to a minimum-phase family is proposed in this paper. The proposed converter exhibits better dynamic performance, steady-state voltage gain in between conventional buck and quadratic buck converter. In view of this characteristic, it gives more bucking than the traditional buck converter. A time-domain analysis is formulated to predict the converter's steady-state performance. Also, the equations for designing the energy storage elements are established. Salient performance features, voltage bucking and source current ripples, of the proposed converter are compared to other competing/reported buck topologies. Transfer functions are obtained through state-space models, and then these are used in the controller design studies. The converter stabilization characteristics are studied through simulations. The analytical predictions and key features of the proposed converter are verified through experimental results. [ABSTRACT FROM AUTHOR]

Cascaded converters are adopted in many power systems to manage sources and loads at different voltage levels simultaneously. DC bus capacitor is one of the key components in these converters due to its energy storage and fast response capabilities. However, the ripple current through the capacitor will influence its lifetime and the overall efficiency of the converter. Previous studies showed that the capacitor current of ac systems is optimized when the duty cycles are synchronized under in phase or antiphase condition. In this paper, the bus capacitor ripple current of cascaded two-stage converters for dc systems with different combinations of duty cycles is analyzed. It is found that the optimum capacitor current ripple varies depending on the values of individual duty cycles and the phase-shift angle between them. By properly adjusting the phase shift, the capacitor RMS current value can be reduced without affecting the converter normal operation or the need for extra sensing circuits, hence improving the energy conversion efficiency and prolonging the capacitor lifetime with relatively simple implementation. To illustrate, a case study of a two-stage dc/dc converter is carried out. A laboratory prototype converter confirmed a maximum efficiency improvement of 2.8% if the phase shift is adjusted properly when compared to the same converter with the worst case phase-shift angle. [ABSTRACT FROM AUTHOR]

This paper assesses the feasibility of three-phase pulse-width modulated (PWM) three-level voltage-source converters (VSC), namely neutral-point-clamped (3L-NPC) and T-type (3L-T) as alternatives to two-level converter (2L-VSC) for low-voltage multimegawatt renewable energy grid-connected converter applications. For this purpose, a novel design algorithm that takes switching frequency, capacity factor, modulation index, PWM scheme(s), and converter topology(ies) as input is unveiled to provide the design steps and performance benchmark for the specified topologies and modulation methods. Design of the LCL filter is also addressed, and equivalent output ripple performance criteria is used to benchmark the converter performances for a set of selected filter parameters. Main contribution of this algorithm is that it covers cost and operating factors of the design during the hardware design phase by introducing/modifying the terms of total cost of ownership (TCO) and return on investment (ROI) time considering the major energy markets. The design is detailed for 1-MVA system, and the results are summarized for 0.5 and 2-MVA systems. The study shows that 3L topologies perform more efficiently than 2L-VSC (T-type being the most prominent—with the shortest ROI), whereas the difference becomes much more prominent at the multimegawatt range, provided that all three yield equivalent outputs fulfilling the stringent grid codes. [ABSTRACT FROM PUBLISHER]

The unipolar sinusoidal pulse width modulation full-bridge transformerless photovoltaic (PV) inverter can achieve high efficiency by using latest superjunction metal–oxide–semiconductor field-effect transistor (MOSFET) together with silicon carbide (SiC) diodes. However, the MOSFETs are limited to use in transformerless PV inverter due to the low reverse-recovery characteristics of the body diode. In this paper, a family of new transformerless PV inverter topology for a single-phase grid-tied operation is proposed using superjunction MOSFETs and SiC diodes as no reverse-recovery issues are required for the main power switches for unity power operation. The added clamping branch clamps the freewheeling voltage at the half of dc input voltage during the freewheeling period. As a result, the common-mode voltage kept constant during the whole grid period that reduces the leakage current significantly. In addition, dead time is not necessary for main power switches at both the high-frequency commutation and the grid zero crossing instant, results low-current distortion at output. Finally, a 1-kW prototype is built and tested to verify the theoretical analysis. The experimental results show 98.5% maximum efficiency and 98.32% European efficiency. Furthermore, to show the effectiveness, the proposed topology is compared with the other transformerless topologies. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped (4L-HC) inverter is a newly proposed topology which is suitable for high-performance medium-voltage drives. Each phase of this topology consists of eight switches and a flying capacitor and the dc-link is split into three parts by two neutral points. In order to ensure the topology operating properly, the voltages across the flying capacitors and three dc-link capacitors should be controlled and maintain balanced at their nominal values. This paper presents a decoupled voltage balancing method for this 4L-HC inverter, including the voltage balancing of dc-link capacitors and flying capacitors. A modified phase-shifted pulse-width modulation method is used to regulate the voltages of flying capacitors and the central dc-link capacitor. The relationship between the neutral-point currents and the output voltage is studied and the upper and lower dc-link capacitor voltages are balanced by injecting an optimum zero-sequence voltage. Simulation and experimental results are presented to verify the validity of this method. [ABSTRACT FROM AUTHOR]

This paper revisits the switched flow graph (SFG) technique. A general and unified equivalent SFG model of a three-terminal switcher encountered in regular and tapped inductor converters operating in the continuous conduction mode is proposed. The model can be applied to most PWM topologies and facilitates construction of a complete flow graph of a given converter. The approach can be helpful in theoretical analysis and derivation of analytical expressions of converter's small-signal transfer functions. The suggested methodology extends the previously proposed SFG analysis technique and alleviates the principal difficulties involved. Furthermore, the approach is straightforward and expeditious. Application guidelines and examples are presented and compared to simulation and earlier theoretical results. [ABSTRACT FROM PUBLISHER]

This paper presents a shunt power compensator based on the interconnection of three-phase two-level converters, and its comparison with two-level- and multilevel-based topologies. The shunt power compensator based on interconnected three-phase converter (ITC) is compared with compensators based on the two-level converter, three-level neutral-point clamped converter, and five-level modular multilevel converter. The comparisons were done in terms of components ratings, harmonic distortion, and semiconductor losses. Control strategies suitable to control the compensator and circulating currents, as well as the three-dc-link voltages are presented. The PWM strategy to generate the control reference voltages of the converter command is designed. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

In this paper, a new open-winding control strategy is proposed for a brushless doubly fed reluctance generator (BDFRG) used for stand-alone wind turbine or ship generators. The BDFRG is characterized with two windings on the stator: a power winding and a control winding. The control winding is fed with dual two-level three-phase converters, and a vector control scheme based on space vector pulsewidth modulation is designed. Compared with traditional three-level inverter systems, the dc-link voltage and the voltage rating of power devices in the proposed system are reduced by 50% while still greatly improving the reliability, redundancy, and fault tolerance of the proposed system by increasing the switching modes. Its performance is evaluated by simulation in MATLAB/Simulink and an experimental study on a 42-kW prototype machine. [ABSTRACT FROM PUBLISHER]

In this paper, a pulsewidth modulation (PWM) plus secondary-side phase-shift (SSPS) controlled full-bridge three-port converter (FB-TPC) is proposed for a renewable power system, which is derived by integrating two interleaved buck/boost circuits (IBBC) and a SSPS full-bridge converter (FBC), to interface the energy source, energy storage element, and output load simultaneously. The two switching legs are shared by the IBBC and FBC, which improves the active devices sharing ratio and power density. With PWM plus SSPS control scheme, decoupled power control can be realized and the converter can achieve wide input voltage range power conversion. In addition, zero-voltage switching (ZVS) of both the primary and secondary switches are achieved in a wide range. Furthermore, the circulating current can be greatly eliminated, which helps to reduce conduction losses. Moreover, the voltage stresses on the secondary rectifier are effectively suppressed since the power switches and diodes are clamped to output voltage. The operation principles, output characteristics, ZVS performances, and control strategy are analyzed in detail. Experimental results of a 600-W prototype are provided to verify the effectiveness and the advantages of the proposed converter. [ABSTRACT FROM PUBLISHER]

Photovoltaic systems technological development is driven by the request for higher efficiency and safety. These concerns influence also the choice of the power converter stage. Several topologies have been proposed and many of them are available commercially. Among them, the neutral point clamped (NPC) and derived topologies offers high efficiency, low leakage current, and low EMI. However, one main disadvantage of the NPC inverter is given by an unequal distribution of the losses in the semiconductor devices, which leads to an unequal distribution of temperature that can affect lifetime. By using the active NPC (ANPC) topology, where the clamping diodes are replaced by bidirectional switches, the power losses distribution problem is alleviated. The modulation strategy is a key issue for losses distribution in this topology. In this paper, two known strategies are discussed and a new PWM strategy, namely the adjustable losses distribution is proposed for better losses distribution in the ANPC topology. Simulations and experimental results help in evaluating the modulation strategies. [ABSTRACT FROM AUTHOR]

A hybrid switched-capacitor/interleaved boost converter able to provide a high voltage gain and to cancel the input current ripple at a preselected duty cycle was recently presented in the literature. This paper extends that work by proposing an optimized switching strategy for operating conditions at other values of duty cycle. The switching strategy effect on the converter's voltage gain and input current ripple is quantified and compared against the performance under the conventional switching strategy. The approach is validated in the laboratory through hardware prototyping. [ABSTRACT FROM PUBLISHER]

Bulky electrolytic capacitors, which are often needed in dc systems to filter out voltage ripples, considerably reduce power density and system reliability. In this paper, a ripple eliminator, which is a bidirectional buck–boost converter terminated with an auxiliary capacitor, is adopted to replace bulky capacitors in dc systems. The voltage ripples on the terminals (i.e., the dc bus) can be transferred to the auxiliary capacitor, and the ripples on the auxiliary capacitor can vary in a wide range. Moreover, the average voltage of the auxiliary capacitor can be controlled either lower or higher than the dc-bus voltage, which offers a wide operational range for the ripple eliminator and also the possibility of further reducing the auxiliary capacitance. Hence, the total capacitance required can be much smaller than the originally needed. After proposing a control strategy to transfer the voltage ripples to the auxiliary capacitor, three control strategies are proposed to regulate the auxiliary-capacitor voltage to maintain proper operation. Intensive experimental results are presented to demonstrate the performance. [ABSTRACT FROM PUBLISHER]

For the development of communication systems such as Internet of Things, integrating communication with power supplies is an attractive solution to reduce supply cost. This paper presents a novel method of power/signal dual modulation (PSDM), by which signal transmission is integrated with power conversion. This method takes advantage of the intrinsic ripple initiated in switch mode power supplies as signal carriers, by which cost-effective communications can be realized. The principles of PSDM are discussed, and two basic dual modulation methods (specifically PWM/FSK and PWM/PSK) are concluded. The key points of designing a PWM/FSK system, including topology selection, carrier shape, and carrier frequency, are discussed to provide theoretical guidelines. A practical signal modulation–demodulation method is given, and a prototype system provides experimental results to verify the effectiveness of the proposed solution. [ABSTRACT FROM PUBLISHER]

The five-leg back-to-back converter shares a leg between the grid and load sides. In the conventional five-leg converter, all legs are of same type, i.e., either two- or three-level legs. This paper presents topologies of five-leg converters based on the combination of two- and three-level legs. The proposed configurations permit one to obtain intermediary characteristics between the five-leg converter with all three-level legs and that with all two-level legs. The choice of the number of two- and three-level legs and how combine them are shown in order to obtain some characteristics of the grid- and load-side converter voltages. The modeling of the system and the pulsewidth-modulation strategy based on carrier-based and space-vector approaches is presented. Analysis of the total harmonic distortion and power switches losses are also addressed to characterize the configurations. Experimental and simulated results show the system feasibility. [ABSTRACT FROM AUTHOR]

In this paper, a comparative study of the effect of different converter topologies on the iron loss of nonoriented electrical steel is presented. Three converter topologies are considered in this investigation; namely: two-, three-, and five-level power converters. Moreover, the effect of the carrier frequency on both the iron loss and converter loss is introduced. The experimental results show a dramatic increase of the iron loss for the two-level converter, especially for low levels of the carrier frequency. Furthermore, the increase of the iron loss is negligible for the multilevel converter topologies. Specifically, the use of the five-level converter, even at a low value of the carrier frequency, results in lower iron losses than the three-level converter at a relatively higher carrier frequency. [ABSTRACT FROM AUTHOR]

This paper presents a single-phase transformerless grid-connected photovoltaic converter based on two cascaded full bridges with different dc-link voltages. The converter can synthesize up to nine voltage levels with a single dc bus, since one of the full bridges is supplied by a flying capacitor. The multilevel output reduces harmonic distortion and electromagnetic interference. A suitable switching strategy is employed to regulate the flying-capacitor voltage, improve the efficiency (most devices switch at the grid frequency), and minimize the common-mode leakage current with the help of a novel dedicated circuit (transient circuit). Simulations and experiments confirm the feasibility and good performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

A medium-voltage (MV) wind turbine generator (WTG)-battery energy storage (BESS) grid interface converter topology with medium-frequency (MF) transformer isolation is introduced in this paper. The system forms a three-port network in which several series stacked ac-ac converters transform the low-frequency (50/60 Hz) utility MV into MF (0.4 to 2 kHz) ac voltage by modulating it with MF square wave. This voltage is then fed to the MF transformer primary windings. The secondary and tertiary windings interface with the WTG side and the BESS side, respectively, after power conversion. The power generated by WTG is transferred to the MF transformer secondary windings through a three-phase pulse width modulation (PWM) rectifier and a three-phase PWM inverter, whereas the power transfer between the BESS and the tertiary winding occurs through a three-phase PWM inverter. It is shown that the utility grid sinusoidal currents, the battery current, and the WTG output currents can be controlled to be of good quality using PI and DQ control strategies. Thus, the proposed MF transformer-based three-port topology results in smaller converter weight/volume. Moreover, the control can handle voltage sags/swells and provide low voltage ride-through capability. Simulation waveforms along with experimental results are shown as proof of concept. [ABSTRACT FROM AUTHOR]