Search

In this paper, a new modulation strategy based on the carrier-based switching strategy for the non-square direct matrix converters (MC) is proposed to control the active power of distributed generation (DG) units. In this strategy, the active power of DGs is controlled by the central input current control of the non-square direct MC independent from the voltage and frequency. Conventionally, each DG has a converter, and for supplying a load with N number of DGs, N number of converters are needed and each converter has its own modulation switching and control strategy to control the power output of each DG. Needless to say, in a microgrid with N number of DGs, the control strategy of each converter has more complex structure than that of a microgrid with one converter, and surely the former strategy entails more volume and price. Using the proposed converter in this paper, it is possible to supply a load with N number of DGs through one converter. Also, the power outputs of all DGs are controlled by a central control strategy. The proposed central control strategy is described and simulated for a typical microgrid. Experimental and simulation results validate the effectiveness of the proposed converter and the proposed strategy. The results demonstrate the applicability and efficiency of the system and verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

Service restoration is one of the critical functions to enable the future self-healing distribution system. To restore the distribution system in a timely and reliable manner, the realistic system operating conditions need to be accurately characterized. In this paper, two main factors that have great impacts on distribution system restoration (DSR) in practice are investigated. First, cold load pickup (CLPU), generally caused by thermostatically controlled loads (TCLs), is a common phenomenon after an outage and shaped by the outage duration. However, the time-dependent behaviors of CLPU are rarely considered in literature. In this paper, the operating state evolution of TCLs after an outage is analyzed to characterize time-dependent CLPU. And the time-dependent CLPU is analytically embedded in DSR to accurately represent the actual behaviors of the restored loads. Second, it is difficult to predict loads that fluctuate during DSR due to the lack of real-time measurement data. Accordingly, a robust DSR based on the information gap decision theory (IGDT) is proposed to address this challenge, fully considering the uncertainty of CLPU. The proposed models are tested in IEEE 13-node and 123-node test feeders. Simulation results demonstrate that the time-dependent CLPU model and the uncertainty modeling of CLPU can accurately capture the actual behaviors of loads with TCLs after an outage, which greatly improves DSR decisions in practice. [ABSTRACT FROM AUTHOR]

In the face of increasing natural disasters and an aging grid, utilities need to optimally choose investments to the existing infrastructure to promote resiliency. This paper presents a new investment decision optimization model to minimize unserved load over the recovery time and improve grid resilience to extreme weather event scenarios. Our optimization model includes a network power flow model which decides generator status and generator dispatch, optimal transmission switching (OTS) during the multi-time period recovery process, and an investment decision model subject to a given budget. Investment decisions include the hardening of transmission lines, generators, and substations. Our model uses a second order cone programming (SOCP) relaxation of the AC power flow model and is compared to the classic DC power flow approximation. A case study is provided on the 73-bus RTS-GMLC test system for various investment budgets and multiple hurricane scenarios to highlight the difference in optimal investment decisions between the SOCP model and the DC model, and demonstrate the advantages of OTS in resiliency settings. Results indicate that the network models yield different optimal investments, unit commitment, and OTS decisions, and an AC feasibility study indicates our SOCP resiliency model is more accurate than the DC model. [ABSTRACT FROM AUTHOR]

Topology control has garnered recent consideration for its value in leveraging the flexiblity of the power system. However, using even the latest technology, the AC optimal transmission switching (ACOTS) problem remains intractable. As such, most research addressing optimal topology control is based on the DCOPF, which has been shown to be particularly inaccurate for transmission switching decisions in the AC power system. This paper accelerates an existing mixed-integer linear power flow model which has been shown to be very accurate in approximating AC power flows. The aim of the new model is to identify transmission switching candidates to prevent load shed caused by contingency events. The methodology was tested on the IEEE 118-bus test case system and presents promising results. The model proposed herein was found to almost always identify AC optimal switching actions while significantly reducing the necessary solution time in comparison with the base model. [ABSTRACT FROM AUTHOR]

This paper summarizes simulation based technical feasibility and cost benefit analyses of a range of off-the-shelf electrical losses reduction intervention solutions in the Isle of Wight (IoW) 11 kV distribution network in the United Kingdom (UK), assessed over a period of 45 years. Based on presented results, the paper provides a brief commentary on the merits, drawbacks, risks and recommendations associated with each considered network intervention. Among considered network interventions, the transformer auto stop-start scheme, where one of the transformers among a pair at a primary substation would be switched depending on the substation's varying load, was found to be the optimal solution, i.e., in reducing technical losses significantly and may also have a reasonable Net Present Value (NPV) with a good rate of Return on Investment (RoI) when fully implemented. [ABSTRACT FROM PUBLISHER]

The ever-increasing utilization of sensitive loads in the industrial, commercial, and residential areas in distribution networks requires enhanced reliability and quality of supply. This can be achieved, thanks to self-healing features of smart grids that already include the control technologies necessary for the restoration strategy in case of a fault. In this paper, an analytical and global optimization model is proposed for the restoration problem. A novel mathematical formulation is presented for the reconfiguration problem reducing the number of required binary variables while covering more practical scenarios compared to the existing models. The considered self-healing actions besides the network reconfiguration are the nodal load-rejection, the tap setting modification of voltage regulation devices (incl. OLTCs, SVR, and CBs), and the active/reactive power dispatch of DGs. The voltage dependency of loads is also considered. Thus, the proposed optimization problem determines the most efficient restoration plan minimizing the number of de-energized nodes with the minimum number of self-healing actions. The problem is formulated as a Mixed-Integer Second Order Cone Programming (MISOCP) and solved using the Gurobi solver via the MATLAB interface YALMIP. A real 83–node distribution network is used to test and verify the presented methodology. [ABSTRACT FROM AUTHOR]

This paper proposes a new formulation for the optimum reconfiguration of islanded microgrid (IMG) systems. The reconfiguration problem is casted as a multi-objective optimization problem, in order to: 1) minimize the IMG fuel consumption in the operational planning horizon for which islanded operation is planned; 2) ensure the IMG capability to feed the maximum possible demand by enhancing its voltage instability proximity index taken over all the states at which the islanded system may reside; and 3) minimize the relevant switching operation costs. The proposed problem formulation takes into consideration the system's operational constraints in all operating conditions based on the consideration of the uncertainty associated with renewable resources output power and load variability. Moreover, the proposed formulation accounts for droop controlled IMG special operational characteristics as well as the availability/unavailability of a supervisory microgrid central controller (MGCC). The formulated problem is solved using non-dominated sorting genetic algorithm II (NSGA-II). MATLAB environment has been used to test and validate the proposed problem formulation. The results show that the implementation of appropriate IMG reconfiguration problem formulations will enhance the performance of IMG systems and facilitate a successful integration of the microgrid concept in distribution networks. [ABSTRACT FROM AUTHOR]