Search

This paper describes a flow control of the dye in the paper mill with the quasi-Z-source indirect matrix converter (QZSIMC) fed induction motor drive. More than a decade the voltage-source inverter (VSI) and current-source inverter (CSI) have been used to control the speed of the induction motor, which in turns controls the flow of dye. Recently, the matrix converter (MC) has been an excellent competitor for the VSI or CSI for its compactness. The voltage transfer ratio of the VSI, CSI, and MC has been limited to 0.866. Thus, the efficiency of these converters is less. To improve the voltage transfer ratio the quasi-Z-source network (QZSN) is to be used between voltage source and indirect MC (IMC). The modification in the shoot-through duty ratio of the QZSN varies the voltage transfer ratio greater than 0.866. Different voltage transfer ratios are needed for different voltage sag conditions. For a variation of the duty ratio of the QZSN, the fuzzy logic controller has been presented. To control the IMC vector control with space vector modulation has been presented. This paper proposes the implementation of QZSIMC adjustable speed drive for the flow control of dye in paper mill during different voltage sag conditions. A 4-kW prototype has been built and the effectiveness of the proposed system is verified with simulation results and experimental setup. Simulation is done in MATLAB, Simulink platform. Experimental setup is done with the aid of a TMS320F2812 (Texas Instrument) processor. The experimental results validate the maintenance of the speed of an induction motor at the set condition, thus controlling the perfect flow of dye in paper manufacturing technology. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

Although smart home has received wide attention in recent years, numerous scholars focus more on energy optimization strategy than energy dispatch hardware device (named energy router). Meanwhile, this energy router should have several features, i.e., high renewable energy utilization, energy multi-port and low volume. Thus, this paper designs a nine-port energy router regarding smart home and proposes a multimode hierarchical management strategy for this energy router. First, for the multi-port demand of wind, solar, storage and utilization, this paper presents a nine-port energy router to improve the renewable energy consumption and power supply flexibility. In addition, to reduce the volume of the energy router, a non-isolated AC/DC hybrid topology is constructed through embedding the integrated power electronic converters, which achieves the miniaturization of the energy router. In order to improve the renewable energy utilization rate, the decentralized module control is proposed for the components of energy router to provide the voltage and frequency support for system, and realizes the power sharing of distributed generations (DGs). Furthermore, the power exchange control with three-mode switching is proposed to guarantee the global energy flow balance under complex conditions. Eventually, the feasibility of the energy router is verified by the simulation and experiments. [ABSTRACT FROM AUTHOR]

In order to achieve the purpose of extending the speed range and reducing power electronics devices for the permanent-magnet linear motor drive system, a half-centralized open-end winding (OEW) topology is studied for rail transit applications in this paper. In this topology, compared with the traditional OEW topology, the number of voltage-source-inverters (VSIs) can be reduced from four to three to drive two OEW movers and all these VSIs share a common dc bus voltage. In order to improve the steady-state performances, a four-vector phase model predictive voltage control (FV-PMPVC) is proposed in this paper. Due to the spatial distribution of phase voltage vector (PVV), an orthometric synthesis principle (OSP) is proposed to calculated the duration time for the vector synthesis, which reduces the computation burden and enhances the robustness. Comparing the existing control method, FV-PMPVC can get similar dynamic performances but better steady-state performances. Additionally, the half-centralized topology using FV-PMPVC can have same speed range while less VSIs are required. The effectiveness of FV-PMPVC is verified by experimental results. [ABSTRACT FROM AUTHOR]

Battery energy storage system (BESS) plays an important role in solving problems in which the intermittency has to be considered while operating distribution network (DN) penetrated with renewable energy. Aiming at this problem, this paper proposes a global centralized dispatch model that applies BESS technology to DN with renewable energy source (RES). The method proposed in this paper aims to minimize the power purchase cost considering network active loss cost as well as voltage deviation penalty cost. Later, second-order cone programming (SOCP) method as well as big M method are applied to make the problem tractable. Last, the method illustrated in this paper is applied and validated on a modified IEEE 33-bus benchmark system to verify the effectiveness of the proposed scheduling model. [ABSTRACT FROM AUTHOR]

The use of power converters as solid state transformers is an attractive solution to modernize the power network, but this solution has not been fully addressed for MV and HV substations. This paper presents a customized and simple control for the Modular Multilevel Matrix Converter (M3C), specially conceived for its operation on synchronous ports, which is the case of AC substations. The control allows bidirectional power transfer, generation/absorption of reactive power and provisions of ancillary services. The converter is compared to the back-to-back Modular Multilevel Converter (B2B-MMC) where the key performance indicators to carry out the comparison are power efficiency, number of semiconductor devices, passive components required, footprint, voltage cell balance, fault blocking capability and stress of components. The simulation results show the features, performance and attractiveness of the M3C topology in a 33/11 kV, 16 MW substation under different operating conditions, including grid faults and dynamic operation. The M3C presents similar efficiency and performance than the B2B-MMC, but it uses fewer semiconductor devices, passive components and total cell capacitor energy than the B2B-MMC, reducing cost and footprint. The experimental results show the performance of the M3C under less ideal conditions including a substation transformer saturation and power step response. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

The advancements in smart grid technologies had brought forth the prospect of self-healing distribution grid through intentional islanding, aided by the steadily rising penetration of inverter-based distributed generations (IBDGs). Adaptive protection is the key enabler for this resilient grid architecture. For cost-effectiveness, overcurrent relays (OCRs) with adaptive features had been proposed, often with the sensitivity problem due to low short-circuit current magnitude from the IBDG taken into consideration and largely addressed. However, apart from this widely discussed sensitivity problem, there is an underlying issue on selectivity of the OCR which is frequently disregarded when designing an adaptive overcurrent protection scheme for IBDG dominated microgrid. This selectivity problem is mainly caused by the current diversion to load during fault, which is often disregarded when performing OCR grading for a conventional grid. In this paper, this selectivity problem of the OCR is discussed in depth through a comparative study of conventional grid and a modern IBDG dominated grid. The coordination time interval margin violations problems are demonstrated through theoretical calculations and real-time hardware-in-the-loop experiments. This research aims to provide better insights into the selectivity problem as a step towards achieving a cost-effective yet reliable overcurrent-based adaptive protection for IBDG dominated microgrid. [ABSTRACT FROM AUTHOR]

The single-phase-to-ground (SPG) fault at the valve side of the converter transformer is one of the most critical faults threatening the operation of bipolar half-bridge modular-multilevel-converter-based multi-terminal direct-current (HB-MMC MTDC) systems. Following a valve-side SPG fault, the upper-arm submodule (SM) capacitors in the faulty converter may suffer a serious overvoltage, and the grid-side fault currents may experience no zero-crossings. The existing protection methods generally rely on tripping the grid-side alternate-current circuit-breaker (ACCB), which cannot fully isolate the fault. The healthy poles and stations may encounter severe disturbance and be all blocked, which will lead to a power outage of the entire MTDC system. This paper proposes an ACCB-independent scheme based on thyristor-pairs and damping SMs to address these problems. Antiparallel thyristor-pairs are connected in series within the upper and lower arms in each phase. Serial damping SMs are connected within the lower arms to help the lower-arm thyristor pairs cut off the fault currents. Although the proposed additional devices inevitably cause conduction losses, they can effectively protect the faulty converter and healthy circuit in the MTDC system. Simulations in PSCAD/EMTDC have been conducted to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

With the increasing number of controllable devices in the grid, devices owned by different entities are supposed to cooperatively support the grid operation. To balance the various interests of the customers and the utility, this paper proposes a two-level scheduling algorithm to address voltage regulation by coordinating the customer-owned battery energy storage system (BESS) and utility-owned load tap changers (LTCs) in power distribution systems. The objective is to find the optimal operation scheduling for both BESSs and LTCs that simultaneously maximize the economic payback and satisfy system operation rules. For BESSs, a local optimization problem is formulated in a chance-constrained manner in major consideration of the economic performance. For the utility interest, a Markov decision process (MDP) and a computationally efficient reinforcement learning (RL) algorithm are utilized to solve the optimal tap setting problem. To coordinate BESSs and LTCs, a global voltage adjustment is applied. The effectiveness of the proposed algorithm is validated via simulations on the IEEE 13-node and 34-node distribution test feeders. [ABSTRACT FROM AUTHOR]

This paper presents the variable speed applications of a recently developed generator named Brushless Induction Excited Synchronous Generator (BINSYG) for offshore wind power applications. The machine is basically a Synchronous generator (SG) with its excitation fed from a three-phase Induction Machine (IM). Both the machines are embedded in the same machine frame and share the same magnetic core. The SG feeds power to the dc grid via a five-level Unidirectional Dual Flying Capacitor Active Neutral Point Converter. The converter is controlled such that the Total Harmonic Distortion (THD) of the current flowing through the stator of SG is below 5% and at unity power factor at SG terminal. The excitation developed by IM-type exciter is adjusted using a new control strategy that is proposed for Voltage Source Inverter, such that BINSYG can operate at wide speed range necessary for Wind Energy Systems (WES). The complete system is controlled without using ac voltage sensors and speed encoders. The proposed WES with its control algorithm is first modelled in MATLAB/Simulink. Further, rapid control prototyping verification in the form of real-time results using OPAL-RT is presented for a small scale (5.5 kVA) BINSYG feeding power to a 750 V dc grid. [ABSTRACT FROM AUTHOR]

DC grid has become an important application in power transmission. However, the exist works only have the method to obtain the droop coefficient in a radial topology. Also, this droop coefficient is for V-I droop control. There is no such like method to obtain the droop coefficient for the P-V droop control. This paper proposed a new method for a complex dc grid to obtain the droop coefficients. Firstly, based on the converter control strategies, the types of converter were classified. It will help to find out which kinds of converter can be participated into the dc-side voltage control. Secondly, a virtual node was defined, and the matrix of the dc grid was reshaped to fit the new added virtual node by using the proposed simplification method. An example was shown how this method worked. After that a new method of calculating the P-V droop coefficient was proposed. Finally, a simulation model was investigated to verify if the proposed method can operate in a real system. The results showed that the simplification method can ensure the mathematical relationships of the dc system. And simulations show good performances of the droop coefficient calculation method. [ABSTRACT FROM AUTHOR]

To integrate large-scale islanded onshore wind power with different sizes, this paper proposes an integration system based on the cascaded hybrid HVDC transmission system, which consists of LCC and several MMCs in series connection at the DC side of the rectifier. A large-scale wind farm is connected with one LCC and one MMC while several small-scale wind farms are connected with MMCs directly. Owing to the hierarchical integration arrangement, the operating flexibility can be improved with reduced capacity and the number of step-up interfacing transformers. A resilient DC voltage control is proposed for the integration system to adaptively redistribute power among the converters during wind power fluctuations. Firstly, the topology and operating characteristics of the wind power integration system are introduced. Then, a resilient DC voltage control is proposed to ensure stable operation during wind power curtailments. Finally, a simulation model of the hybrid cascaded HVDC transmission system is built in PSCAD/EMTDC to verify the effectiveness. The research results show that the system provides a new option for long-distance transmission of large-scale islanded wind power. [ABSTRACT FROM AUTHOR]

The proliferation of distributed energy resources (DERs), located at the Distribution System Operator (DSO) level, bring new opportunities as well as new challenges to the operations within the grid, specifically, when it comes to the interaction with the Transmission System Operator (TSO). To enable interoperability, while ensuring higher flexibility and cost-efficiency, DSOs and the TSO need to be efficiently coordinated. Difficulties behind creating such TSO-DSO coordination include the combinatorial nature of the operational planning problem involved at the transmission level as well as the nonlinearity of AC power flow within both systems. These considerations significantly increase the complexity even under the deterministic setting. In this paper, a deterministic TSO-DSO operational planning coordination problem is considered and a novel decomposition and coordination approach is developed. Within the new method, the problem is decomposed into TSO and DSO subproblems, which are efficiently coordinated by updating Lagrangian multipliers. The nonlinearities at the TSO level caused by AC power flow constraints are resolved through a dynamic linearization while guaranteeing feasibility through “ $l_1-$ proximal” terms. Numerical results based on the coordination of the 118-bus TSO system with up to 32 DSO 34-bus systems indicate that the method efficiently overcomes the computational difficulties of the problem. [ABSTRACT FROM AUTHOR]

A novel high conversion ratio bidirectional C-dual transformers-LC (CDT-LC) resonant dc–dc converter is proposed in this paper. Based on the traditional LLC, an auxiliary transformer and an extra resonant capacitance are employed in the CDT-LC structure. It not only harvests high efficiency, but exhibits a good voltage gain feature. Especially for the case of light load, CDT-LC still harvests a high efficiency, compared with traditional converters. Also, it can achieve a fast gain reduction when the switching frequency is higher than resonant frequency. In this paper, the operating principles of the converter are analyzed in both bidirectional operation modes. In addition, its dual-transformers structure feature and voltage gain characteristics are discussed in details. Furthermore, the parameter design method is provided. Moreover, the loss breakdown for the converter is given in details. Finally, a 2.5-kW prototype is established to verify the performance of the CDT-LC converter, and its maximum efficiency reaches 97%. [ABSTRACT FROM AUTHOR]

The series bridge converter (SBC) is a modular multilevel converter (MMC) recently developed to enhance power density in high-voltage high-power applications. The MMC is a well-established solution, widely researched, and exploited in practical HVdc connections, thanks to its high power quality and high efficiency. However, the main limitation of the MMC is the relatively large energy storage, also due to the fact that power ripples in the submodule capacitors include a component at the fundamental ac frequency. As a result, volume becomes critical in applications such as offshore or city center in-feeds, where space is restricted and expensive. The SBC offers a more compact footprint by exploiting a series connection on the dc side and by operating the submodules with rectified waveforms, thus moving the minimum component of the instantaneous power to twice the ac fundamental and reducing capacitors size. The drawback of the converter is a more complex energy control compared to the MMC. This paper proposes the first experimental validation of the SBC, using a 2-kW laboratory-scale prototype. Since the basic converter design has been discussed in previous papers, the focus of this paper is on converter control design and experimental validation. [ABSTRACT FROM AUTHOR]

Compared with the conventional two-level dual-active-bridge (DAB) dc–dc converter, the three-level DAB converter could operate with lower voltage rated switching devices and provide more control degrees of freedom, which enhances the control flexibility. This paper proposes a modulation strategy with five control degrees of freedom. In the previous work with multiple control degrees, the optimization strategies for efficiency or inductor current minimization are investigated; however, these strategies all need detailed mode analysis and complex mathematical optimization tools to obtain the optimal duty cycles. In this paper, an optimization strategy for the root-mean-square value of the inductor current is proposed. This method extracts the fundamental and third-harmonic components from the high-frequency voltages on both sides and adjusts the amplitude of the bridge voltages by the vector diagram to obtain the optimal duty cycles. The inductor current can be reduced significantly at light loads with the proposed strategy, so the efficiency of the converter can be improved. Moreover, the optimization process does not need the detailed operation analysis of the converter, nor does it require the complex mathematical optimization tools. Finally, the performance of the three-level DAB and the optimization strategy are verified by the experimental results. [ABSTRACT FROM AUTHOR]

The main technical challenge of the medium-voltage motor drives with modular multilevel converter (MMC) is the serious low-frequency fluctuation on the capacitor voltages, and the existing suppression methods inevitably inject high-frequency circulating currents in MMC. However, the output currents are evidently distorted by the large injected components, while little research has been done to study and solve this problem. This paper analyzes and proves the essential interactions between the output current distortion and the injected components, and the specific dominant output harmonic groups are derived and summarized, revealing the nature of the problem, and it can be taken as a favorable reference for the controller designing. Based on the derivations, this paper proposes a novel suppression method for the greatly improved harmonic characteristics of the output currents during the low-frequency operation. The output harmonics can be accurately measured by the proposed control and effectively suppressed for much lower current total harmonic distortion, benefiting for the superior output control performances with improved efficiency. The simulation results on PSCAD/EMTDC and experimental verifications on a 2.2 kW MMC-based motor drive prototype prove the validity of the presented harmonic analysis and suppression method. [ABSTRACT FROM AUTHOR]

The emergence of applications which require high-voltage switches has created a tendency to use semiconductor device series stacks. These series stacks permit operation at blocking voltages above semiconductor elements’ nominal voltage. Insulated-gate bipolar transistors (IGBT) are currently utilized for controllability and switching speed, when these topologies are employed. The main challenge therewith is guaranteeing voltage balance between IGBTs, both when blocked and when switching transistors. Most of the methods which have been proposed to mitigate static and dynamic voltage unbalances increase transistor losses. The series stack loss-less high voltage switch (LHVS) which mitigates voltage unbalances, thus reducing switching losses, is presented in this paper. LHVS consists of a circuit, which ensures soft IGBT switching, an energy recovery circuit, and a gate delay compensation circuit. Additionally, the insulation voltage level is guaranteed to be equal between control circuit and high-voltage side of each IGBT. The operating principle of the LHVS is detailed in this paper, as is experimental validation which has been performed for three series stack modules. Static unbalances are reduced to 1%, while the differences between collector–emitter voltage curves in switching “on” do not surpass 8 ns, and switching losses are reduced by 41%, as compared to the hard-switching topology. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are playing a pivotal role in the power sector with potential applications, such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost, and higher efficiency compared with their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level voltage-source inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the dc-link capacitors and FCs. The generation of various output voltage levels and the limitation of the sinusoidal pulsewidth modulation control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared with the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique. [ABSTRACT FROM AUTHOR]

This paper introduces a novel leaky least logarithmic absolute difference (LLLAD)-based control algorithm and a learning-based incremental conductance (LIC) maximum power point tracking algorithm for a grid-integrated solar photovoltaic (PV) system. Here, a three-phase topology of the grid-integrated PV system is implemented, with the nonlinear/linear loads. The proposed LIC technique is an improved form of an incremental conductance (InC) algorithm, where inherent problems of the traditional InC technique, such as steady-state oscillations, slow dynamic responses, and fixed-step-size issues, are successfully mitigated. The prime objective of the proposed LLLAD control is to meet the active power requirement of the loads from the generated solar PV power, and after satisfying the load demand, the excess power is supplied to the grid. However, when the generated solar power is less than the load demand, then LLLAD meets the load by taking extra required power from the grid. During these power management processes, on the grid side, the power quality is maintained. During daytime, the proposed control technique provides load balancing, power factor correction, and harmonic filtering. Moreover, when solar irradiation is zero, then the dc-link capacitor and a voltage-source converter act as a distribution static compensator, which enhances the utilization factor of the system. The proposed techniques are modeled, and their performances are verified experimentally on a developed prototype in solar insolation variation conditions, unbalanced loading, and in different grid disturbances such as over- and undervoltage, phase imbalance, harmonics distortion in the grid voltage, etc. Test results have met the objectives of the proposed paper, and parameters are under the permissible limit, according to the IEEE-519 standard. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

With the increasing proliferation of variable speed drive, the demand for the more reliable drive is also on the rise. Despite the growing interest on more advanced motors like permanent magnet and flux switching motors, three-phase induction motors (3ph-IMs) are still the main workhorse in the industry and hence the fault-tolerant control of these motor drives remains an interesting and important topic. In this paper, a simple fault-tolerant field-oriented control technique for 3ph-IMs is presented. It is shown that by injecting zero-sequence compensation voltage in a feedforward manner, open-circuit faults can be effectively tolerated. Compared to the previous feedforward fault-tolerant control methods, the proposed approach does not require the knowledge of the magnetizing inductance, which is tricky to be obtained in induction motors. Furthermore, the unified feedforward approach allows the same control structure to be used for different fault-tolerant 3ph-IMs drive topologies, with minor modifications to the feedforward terms. In addition, the effect of inverter non-idealities on the performance of the proposed control method is also highlighted and addressed. The effectiveness of the proposed controller is verified using MATLAB simulation and further validated using experimental tests. This paper is accompanied by a video demonstrating the experimental results. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

This paper presents an isolated single-stage on-board electric vehicle charger without an intermediate DC-link. Based on an isolated current-source topology, the converter features soft-switching in semiconductors regardless of load variation for the full AC line voltage range. Moreover, it requires no external snubber or clamp circuits. The power factor correction and voltage regulation are provided by a relatively simple phase shift modulation, while the amount of circulating energy is kept at minimum. The charger is distinguished by its efficiency characteristic – the maximum is achieved in the constant power charging mode. The control method, component stresses, and design constraints of the topology are analyzed. The concept is verified using a 3 kW experimental SiC-based prototype, which reaches a peak efficiency of 96.4%. Moreover, the charger has demonstrated efficiencies above 95% with the THD of 4.1% when operating in constant power mode at the maximal power. [ABSTRACT FROM AUTHOR]

Energy management in modular type converters constitutes a key aspect of their operational stability. This paper introduces a full energy management structure for the Extended Overlap-Alternate Arm Converter (EO-AAC) ensuring both equal energy distribution across all six stacks and the maintaining of ripple-free DC current during steady state. The performance of the control structure against active power step events is validated by detailed simulations using EMTP-RV software. Moreover, the full energy management allows the EO-AAC to have an equivalent controllability to Modular Multilevel Converter (MMC) through only two conducting stacks in overlap mode ensuring the power balance. From this observation, it is demonstrated that the use of control strategy like the virtual capacitor to support HVDC system, originally designed for MMC, is possible. Gathering all these controllers leads to a general conclusion which is the dynamic equivalence between EO-AAC and MMC. [ABSTRACT FROM AUTHOR]

The regulation of active power flowing through one or multiple DC lines plays an important role to guarantee secure and economic operations of high voltage direct current (HVDC) grids. This paper proposes a new method to regulate DC line power flow based on the adaptive DC voltage droop control strategy in which the voltage references of the voltage droop controllers vary autonomously at post-contingencies. The main advantage of the proposed method is that it can avoid installation of extra equipment and thus the associated losses and costs in the power-converter-based power flow control methods. The proposed control approach does not require to solve online global AC-DC power flow equations, leading to autonomous control. Furthermore, the adaptive droop control does not influence the stability of the HVDC grid since only the droop voltage references vary, but not the droop coefficients. Static analysis and dynamic simulations of a five-terminal HVDC grid are implemented using MATLAB/Simulink Simscape Blockset and OPAL-RT RT-LAB libraries to validate the effectiveness of the proposed autonomous control method. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

In this paper, we propose a topology-cognizant optimal power flow (OPF) paradigm with additional safety constraints for multi-terminal direct current (MTDC) grids. The resulting formulation is concerned with the optimization of controller set-points, i.e., voltage and power levels at each bus, and the switching status of transmission lines that collectively referred to as grid topology. A pair of additional safety constraints are integrated into the problem formulation to prevent voltage violations caused by power fluctuations in between two controller set-point updates. Searching for a grid topology that offers more efficient operation leads to a mixed-integer nonlinear program (MINLP) which is computationally challenging due to: i) Non-convex power flow equations, (ii) Non-convex converter loss equations, and iii) Binary variables accounting for the operational status of transmission lines. Non-convexities of power flows and converter loss equations are tackled by means of a mixed-integer second-order cone programming (MISOCP) relaxation, while the optimal switching status of transmission lines are determined via a branch-and-bound search. Numerical results for the modified IEEE 14, 30, and 57-bus systems are used to verify the merits of the proposed method. Furthermore, this method is experimentally validated using the CIGRE B4 DC grid benchmark in a real-time hardware-in-the-loop platform. [ABSTRACT FROM AUTHOR]

Conventionally, the converter of switched reluctance motor (SRM) is fed by the uncontrollable diode bridge rectifier (DBR), which leads to a low grid-side power factor (PF) and high current total harmonic distortion (THD). In this paper, an alternative solution for the grid-connected high-speed SRM drive system with improved PF is proposed. In the proposed drive system, the three-level active front end (AFE) is connected in cascade with the midpoint converter for SRM operation. A centralized strategy, which controls the AFE and SRM together, is proposed to govern the motor speed and grid-side PF by regulating the real power and reactive power of the system, respectively. Specifically, the real power, reactive power, and the voltage balancing of split capacitors are controlled by the model predictive directed power control (MP-DPC) algorithm, which significantly reduces the control complexity and guarantees the fast dynamic response. Consequently, satisfying speed regulation, high PF, low current THD, and bi-directional power-transfer capability are achieved. An idea-proofed testbench is constructed in laboratory, and the applicability of the proposed drive system is verified by a series of experimental results. [ABSTRACT FROM AUTHOR]

The emulation of virtual resistance finds various applications in the power processing industry. This paper proposes a novel notion of adaptive sliding mode based loss free resistor (ASLFR). This is achieved by allowing the input power of the power-out power-in (POPI) system to vary, in order to accommodate the load demands. In this paper, the concept is illustrated for power-factor correction (PFC) applications. The ASLFR is used to achieve the dual purpose of harmonics-free rectification along with excellent system response under load and line transients. The scheme serves itself as an efficient single-stage PFC solution. A generic mathematical formulation of the scheme is presented, which can be used for different converters. Then on, a boost topology, operating in continuous conduction mode, is chosen to demonstrate theoretical developments and to showcase the effectiveness of the scheme. The robustness of the proposed controller to any line or load variation is established. A fast voltage recovery with almost no undershoot/overshoot is achieved at transients by using the proposed controller. Additionally, a qualitative analysis is provided to demonstrate the expediency of the proposed ASLFR. The theoretical claims are well supported by simulation as well as experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase ac–dc–ac converter composed of a transformer and two three-leg converters connected in series. The proposed converter allows to supply the load with a voltage with constant amplitude and frequency, and to operate with the grid current with low harmonic distortion and high power factor. In addition, the converter can be used to mitigate fundamental overvoltage and voltage harmonics at the grid. The system model, regions of operation, a power flow analysis, and a method to regulate the dc-link voltages using the voltage vector redundancies are given. In the first version of this paper, two pulsewidth modulation (PWM) techniques (including space vector PWM) and a control system were provided. The proposed topology is compared with two conventional systems in terms of operation range, harmonic distortions, and semiconductor losses. Simulation and experimental results are provided to validate the feasibility of the system. [ABSTRACT FROM AUTHOR]

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

The photovoltaic (PV) output voltage varies over a wide range depending on operating conditions. Thus, the PV-connected converters should be capable of handling a wide input voltage range while maintaining high efficiencies. This paper proposes a new series resonant dc–dc converter for PV microinverter applications. Compared with the conventional series resonant converter, a dual-mode rectifier is configured on the secondary side, which enables a twofold voltage gain range for the proposed converter with a fixed-frequency phase-shift modulation scheme. The zero-voltage switching turn-on and zero-current switching turn-off can be achieved for active switches and diodes, thereby, minimizing the switching losses. Moreover, a variable dc-link voltage control scheme is introduced to the proposed converter, leading to a further efficiency improvement and input-voltage-range extension. The operation principle and essential characteristics (e.g., voltage gain, soft-switching, and root-mean-square current) of the proposed converter are detailed in this paper, and the power loss modeling and design optimization of components are also presented. A 1-MHz 250-W converter prototype with an input voltage range of 17–43 V is built and tested to verify the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper presents research results of voltage gain number control methods of a power electronic resonant zero-current switching dc–dc switched-capacitor (SC) voltage multiplier (SCVM) in a topology with fault tolerance capability (FSCVM). The converters operated under the basic switching patterns are constant-voltage-gain dc–dc series-parallel resonant SC converters. However, this paper presents a method for the output voltage regulation by a special switching strategy. A variable voltage gain is made possible by selecting the number of active switching cells, using an appropriate control method. This creates a set of voltage ratio ranges. In addition, the proposed topology and method of control enable a fault-tolerant operation of the FSCVM under various failures of the device. The paper presents an analysis of the concept, simulation results and an experimental verification in a three-cell FSCVM dc–dc resonant boost converter operating at a 200-watt charge. Issues regarding the selection of components related to the problem of inrush currents that can occur during the voltage ratio increase are also analyzed in this paper, and the design for low inrush currents is demonstrated. [ABSTRACT FROM AUTHOR]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]

This paper presents two capacitor voltage balancing (CVB) strategies for modular multilevel converter (MMC) applications. Both balancing schemes are based on model predictive control and are designed to efficiently solve a constrained optimal control problem, where the predicted capacitor voltage errors are included in the cost function with the demanded output voltage of a cluster being forced through an equality constraint. The first method proposed in this paper computes specific modulation indexes for each module using the explicit solution of a relaxed version of the original optimization problem. The second approach proposed in this paper reduces the complexity of the original problem by linearizing the objective function and using an optimal sorting network based on a greedy algorithm to solve this approximation. Considering the structures of both solution approaches, they are integrated into modulation schemes based on phase-shifted and level-shifted pulsewidth modulation algorithms, respectively. Experimental results obtained from a nine-cell single-phase MMC prototype demonstrate the good performance achieved with the proposed methodologies, as well as the implementation simplicity offered by the proposed CVB algorithms. [ABSTRACT FROM AUTHOR]