Search

DC smart grids represent an alternative to traditional ac power distribution systems. The power conversion stage, interfacing the ac and the dc distribution systems, is the enabling technology to manage multiple dc loads and sources. The three-stage smart transformer (ST) is a promising solution, because it includes a dc–dc power conversion stage providing a dc multibus in output. The modular ST architecture supplies several dc outputs, which allow interfacing a dc smart grid with the ac power system. In this paper, the three-stage ST is based on a cascaded H-bridge (CHB) converter for the ac–dc power conversion, whereas dual active bridge (DAB) converters are adopted for the dc–dc power conversion stage. The peculiarity is that the dc voltage balancing is performed by the dc–dc power conversion stage instead of the CHB converter. It is advantageous for dc smart grids applications where the power sharing among the dc sources and loads is often not balanced. The design of the entire control system is based on the detailed small signal model of the ac–dc and dc–dc power conversion stages of the ST. High dynamic performance of the voltage balancing is fulfilled due to the commonly high switching frequency of the DAB converters. [ABSTRACT FROM AUTHOR]

A novel hybrid mode control technique for a phase-shift full-bridge (PSFB) converter is proposed in this paper. The proposed method can improve power efficiency under both the light-load and heavy-load conditions. The basic concept of the proposed control technique is to decrease the turns ratio to reduce the circulating current, hence resulting in lower circulating losses. However, the output voltage under heavy load may not be stabilized using phase-shift control if smaller turns ratio is utilized. Therefore, the proposed technique employs asymmetrical pulsewidth modulation to achieve higher output voltage. To further improve the efficiency, an adaptive dead-time control method, which determines the dead-time value according to the load level, is also proposed. To validate the correctness and effectiveness of the proposed method, a 480-W PSFB converter is constructed and experiments are carried out accordingly. Comparing with a conventional PSFB converter, the efficiency of the proposed method can be improved up to 3.2%, 1.3%, and 0.6% under light-load, 30% load, and full-load conditions, respectively. [ABSTRACT FROM AUTHOR]

The half-bridge modular multilevel converter (MMC) is a voltage source converter (VSC) with high efficiency, controllability, and modularity. The topology is weak to dc side faults unless bipolar submodules are used, but this results in decreased efficiency. Power groups (PGs), a thyristor augmented multilevel structure, have been proposed as a way to reduce the power-loss increase arising from achieving dc-fault-tolerance. This paper investigates whether the PG concept can also achieve significant efficiency improvements in VSCs that are not required to be dc fault tolerant. A single submodule voltage (SSMV) method of controlling the turn-on/turn-off of the thyristor assembly within each PG structure is presented, and the differences with the previously detailed dual submodule voltage (DSMV) technique are described. Two thyristor-based PG structures for use in non-dc-fault-tolerant MMCs are proposed, one using SSMV and the other using DSMV. A comparison is made considering the required semiconductor device count, the impact on thyristor snubber design, and the overall power-losses achieved. A further, simplified, variant using a diode bypassed PG structure is presented, which results in power-loss reductions during rectifier mode only. Results show that power-loss reductions of $\sim$ 20%–25% can be achieved by using the proposed PG structures to augment a half-bridge MMC. [ABSTRACT FROM AUTHOR]

In meshed High Voltage Direct Current (HVDC) grids, Current Flow Controllers (CFC) may be required to avoid bottlenecks or line overloads. The present paper proposes the concept of installing Distributed Current Flow Controllers (DCFCs) in different nodes of a meshed HVDC grid that are operated selectively. This concept allows to use simplified DCFC devices to prevent the overloads, with a reduction of the required CFC voltage compared with a single CFC in the grid. First, a methodology to investigate the effect of installing DCFCs in a generic meshed HVDC grid is presented. Several case studies with a 3-terminal and a 7-terminal meshed HVDC grids are conducted and the most suitable topology for the DCFCs is derived based on the previous analysis. Then, this work analyses the increase in the operational area brought by installing DCFCs in a 3-terminal HVDC grid and it is compared with the increase achieved by a Dual H-bridge CFC in one node. The CFC losses and voltage requirement depending on the location of the DCFCs are investigated. Finally, the operation and control of the DCFCs are designed and tested in a 3-terminal meshed HVDC grid using dynamic simulations. [ABSTRACT FROM AUTHOR]

In this paper, a design and control scheme of the inductive power transfer (IPT) system for electric vehicles are proposed, considering a wide variation in output voltage and coupling coefficient. The characteristics of the proposed IPT system and a design method for the resonant network are suggested. By utilizing the battery management converter at the secondary side, the design and control can be simplified while managing the output voltage and power of the battery. In order to achieve high efficiency by reducing the voltage–ampere rating, zero phase angle tracking control is proposed. In addition, a phase-shift control is applied to the primary side to ensure the stable system operation by limiting output voltage. A 3.3-kW laboratory prototype with magnetic power pads is manufactured, and the validity of the proposed design and control is verified through experimental results using the laboratory prototype. [ABSTRACT FROM AUTHOR]

Transformerless photovoltaic (PV) grid-connected inverters have become more and more popular in distributed PV power generation systems due to the advantages on high efficiency, low cost, and small size. However, common-mode (CM) current in the transformerless PV inverters can result in serious electromagnetic interference and insecurity, which will further reduce the reliability of the PV inverter systems. In this paper, an improved H5 topology, namely H5-D topology, is proposed, in which a clamping diode is added on the basis of H5 topology to eliminate the CM voltage fluctuation in H5 topology. Further, the PSIM simulation results of the H5-D topology and H5 topology are given and compared, especially, the performance of H5-D topology for CM current suppression is presented and analyzed concretely. Finally, the experimental prototypes of the H5-D topology and H5 topology are built and tested, and the experimental results validate the advantages of the H5-D topology. The proposed H5-D topology provides a new practical topology for distributed PV grid-connected power generation systems. [ABSTRACT FROM AUTHOR]

This paper presents a deadbeat-based method for the single-inductor multiple-input multiple-output (SI-MIMO) dc–dc converter. By solving the cross regulation problem of the SI-MIMO dc–dc converter, the proposed method is capable of achieving the input current regulation (ICR) and the output voltage regulation (OVR) simultaneously. Moreover, the output current observers are adopted to replace the output current sensors, which are required by the conventional model based methods for dc–dc converters. The proposed control approaches including ICR and OVR are discussed in detail. To verify the effectiveness of the proposed deadbeat-based method, simulation runs and experiments are conducted on the single-inductor dual-input dual-output buck converter simulation platform and hardware prototype, respectively. The simulation and experimental results are analyzed in detail, and the comparison with the previous works is conducted. [ABSTRACT FROM AUTHOR]

This paper explores the large-signal and small-signal dynamics of a series-capacitor (SC) buck-type converter and introduces an optimal closed-loop control scheme to accommodate both the steady-state and transient modes. As opposed to a conventional buck converter, where time-optimal control is realized by a single on–off cycle, in the SC-buck topology, there is a need to distribute the switching phases to satisfy the charge balance of the SC. The new control method merges a voltage-mode controller for the steady-state operation and a nonlinear, state-plane based transient-mode controller for load transients. A detailed principle of the operation of the SC-buck converter is provided and explained through an average-behavioral model and state-plane analysis. The operation of the controller is experimentally verified on a 20 W 12 V-to-1 V converter, demonstrating voltage-mode control operation as well as minimum-deviation and time-optimal responses for load transients. [ABSTRACT FROM AUTHOR]

Voltages of series-connected batteries gradually become imbalanced due to nonuniformity in terms of not only battery characteristics but also self-discharge rate that is significantly dependent on temperature. In large-scale energy storage systems, a large temperature gradient is very likely because of its huge geometry, and therefore, equalizers capable of relatively large equalization currents would be necessary to eliminate voltage imbalance originating from uneven temperature distribution. A two-switch string-to-battery voltage equalizer using a half-bridge converter with multistacked current doublers (MSCDs) is proposed for series-connected batteries in this paper. The proposed equalizer is capable of providing relatively large equalization currents without increasing ripple currents thanks to the interleaved operation of the MSCDs. Fundamental operational analysis for a discontinuous conduction mode, in which currents in the equalizer can be limited to desired levels without feedback control, is performed. The experimental results of equalization tests performed for four supercapacitor modules and lithium-ion batteries connected in series demonstrated the equalization performance of the proposed equalizer. [ABSTRACT FROM AUTHOR]

This paper introduces a new approach for output voltage regulation in impedance control network (ICN) resonant dc–dc converters, in which the rectifier of the ICN converter alternates between full-bridge and half-bridge topologies. This approach, termed topology morphing control, allows the ICN converter to maintain soft switching across power levels while substantially reducing the output capacitance requirement and improving partial-power efficiencies compared to the conventional burst mode (on/off) control. A closed-loop control architecture for the ICN converter is also introduced, which regulates the converter's output voltage under input voltage and load variations while ensuring smooth transitions between the multiple operating modes of the proposed topology morphing control. A prototype 1-MHz, 120-W step-down ICN resonant converter designed for an input voltage range of 18–36 V, an output voltage of 12 V, and a 10:1 output power range has been built and tested with both burst mode control and the proposed topology morphing control. The topology morphing control reduces the output capacitance requirement in the prototype ICN converter by 57% and reduces converter losses at partial power levels by up to 46.5%. The prototype ICN converter is also tested under closed-loop control and is shown to successfully regulate its output voltage in the face of input voltage and load variations. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive review of multiport converters for integrating solar energy with energy storage systems. With recent development of a battery as a viable energy storage device, the solar energy is transforming into a more reliable and steady source of power. Research and development of multiport converters is instrumental in enabling this transformation in an efficient manner. The high efficiency of conversion in comparatively smaller footprint makes a multiport converter very attractive in this application. Most of the recently reported multiport converter topologies are discussed here. A breakdown of isolated and nonisolated topologies is presented along with the comparison of converter architectures and features such as operating conditions, device count, efficiency, etc. Each group of multiport converters is subdivided into different smaller groups based on their architecture. Detailed specifications are presented for important topologies. Finally, a performance comparison is carried out featuring the advantages and disadvantages of the various topologies leading to suggestions for the direction of future research. [ABSTRACT FROM AUTHOR]

This paper presents an interface ac–dc converter to connect the 380 V bipolar dc microgrid with the 240 V split-phase single-phase ac utility. The design targets are high efficiency, leakage current attenuation, and symmetric bipolar dc bus generation. A transformerless two-stage topology is proposed to decouple the common-mode (CM) voltage between the connected ac and dc systems. The two-stage structure also reduces the required capacitance in single-phase power conversion by allowing a large voltage ripple on the intermediate dc link. Adaptive dc-link voltage control and interleaving of state-of-the-art silicon carbide (SiC) mosfets are adopted to achieve high efficiency. Interleaving angles are optimized to minimize the total volume of both differential-mode and CM magnetics. An active CM control method is incorporated to regulate the dc and low-frequency CM voltages on the dc buses with respect to the ground. The resultant dc bus voltages are rendered symmetric to the ground, and the leakage current is suppressed. The generated ±190 V dc bus is suitable for bipolar 380 V dc power distribution systems. Pluggable phase-leg modules with embedded driving and protection circuit are designed and tested, based on which a 10 kW all-SiC converter prototype is built achieving an efficiency >97%. [ABSTRACT FROM AUTHOR]

In this study, a novel modulation of an isolated three-phase bidirectional dc–dc converter is proposed for the high-voltage input power supply to low-voltage output energy storage systems. The wye-delta connection of the transformers is employed to reduce the voltage stress at the high side and the current stress at the low side of the transformers. Frequency control allows the output voltage regulation, and a phase-shift algorithm with a resonant tank is proposed following with the switching frequency to reduce the frequency range with the specific power. Furthermore, the zero-voltage-switching condition for all mosfets in the entire power range, which is the major restriction of a single-phase converter, is also discussed in this paper. The three-phase wye-delta converter significantly reduces the ripple of inductor current compared with that of a single-phase converter. A 2 kW prototype converter was built and successfully tested to verify the capability of such control modulation. [ABSTRACT FROM AUTHOR]

In this paper, a novel integrated interleaved dual-mode time-sharing inverter (IIDMI) is proposed for grid-tied transformerless photovoltaic (PV) applications. While the dual-mode time-sharing conversion technique ensures minimum losses, the IIDMI also retains the advantages of interleaved topologies, such as low total harmonic distortion of the ac current with reduced filtering requirements, increased power density, and reduced current and thermal stresses of power devices. The leakage current problem, which is a main concern with the transformerless PV inverters, is solved by increasing the frequency of the main side band of the common-mode voltage above the resonance frequency of the common-mode impedance, while avoiding high switching losses. The current control, especially at transitions between the buck and the boost modes of operation, is highly improved by utilizing a fast-response deadbeat control scheme. The working principles of the IIDMI are explained in detail, and a 2.2-kW experimental prototype is implemented to confirm the theoretical achievements. [ABSTRACT FROM AUTHOR]

This paper proposes a novel 11-level improved active-neutral-point-clamped (11L-IANPC) converter for ground power unit (GPU) application. This hybrid topology consists of the 5L-ANPC and the proposed low-voltage submodule. The proposed 11L-IANPC converter possesses only one flying capacitor (FC) and reduced number of high-frequency switches. Hence, voltage diversity and ratings, stored energy, and the number of costly and bulky FCs are significantly decreased. Moreover, operating the augmented submodule at the low voltage and power leads to doubling the number of output voltage levels, whereas the low extra cost and size are imposed on the proposed converter. In addition, suggested sensorless switching method leads to self-balancing of FC and significantly amends the output voltage frequency spectrum. These improvements cause significant reduction in control complexity of the proposed 11L-IANPC converter, remarkable decrease in size of the bulky and costly output LC filter, and improving the dynamic and steady-state performance of the proposed static GPU. The simulation and experimental results validate the feasibility of the proposed converter as well as its suggested modulation and control method. [ABSTRACT FROM AUTHOR]

This paper investigates dc-link capacitor optimization for three-phase photovoltaic-based microinverters. This concept minimizes the storage capacitance by allowing greater voltage ripple on the dc link. Therefore, the microinverter reliability can be significantly increased by replacing electrolytic capacitors with film capacitors. However, this intentionally increased voltage ripple can introduce harmonic distortion on the output current of the inverter stage if it is not mitigated by the dc-link voltage controller. For this purpose, a robust and accurate dc-link voltage control is proposed to filter this ripple while regulating the dc-link voltage without using any additional circuit components. The experimental results on a 400-W three-phase half-bridge microinverter prototype validate the theoretical analysis of the dc-link capacitor optimization and show that a significant reduction of the dc-link capacitor requirement can be achieved. The proposed high-accuracy dc-link voltage controller is also implemented on this prototype to demonstrate very low harmonic distortion of the inverter output current while tightly regulating the dc-link voltage even during transients. [ABSTRACT FROM AUTHOR]

The conventional design of voltage-source power converters is based on a two-level half-bridge configuration and the selection of power devices designed to meet the full application specifications (voltage, current, etc.). This leads to the need to design and optimize a large number of different devices and their ancillary circuitry and prevents taking advantage from scale economies. This paper proposes a paradigm shift in the design of power converters through the use of a novel configurable device consisting on a matrix arrangement of highly optimized switching cells at a single voltage class. Each switching cell consists of a controlled switch with antiparallel diode together with a self-powered gate driver. By properly interconnecting the switching cells, the switching-cell array (SCA) can be configured as a multilevel active-clamped leg with a different number of levels. Thus, the SCA presents adjustable voltage and current ratings, according to the selected configuration. For maximum compactness, the SCA can be conceived to be only configurable by the device manufacturer upon the customer needs. For minimum cost, it can also be conceived to be configurable by the customer, leading to field-configurable SCAs. Experimental results of a 6 × 3 field-configurable SCA are provided to illustrate and validate this design approach. [ABSTRACT FROM AUTHOR]

Power converters used for undersea applications utilize dc current distribution instead of dc voltage distribution due to the long distance from the shore and cable series impedance. Power converter modules employed in such scenarios use a constant current as a source of input power with several modules connected in series. Series-resonant converters (SRCs), which are used in each module, behave differently when driven by a constant-current input in comparison to the conventional case with a constant-voltage input. The differences in the behavior and design of such SRCs have not been thoroughly studied in the literature. In this paper, detailed steady-state analysis is presented to show the findings, and a design procedure is proposed for regulating the output current of an SRC topology with its input connected to a constant-current source. Constraints on the selection of resonant tank components and operating frequency are satisfied, while regulating the output current over the desired load range. The proposed design also considers variations of the component values accounting for the changes due to tolerances as well as aging. A design example for supplying power to an undersea observation system and hardware validation results are provided for a 400 kHz 450 W SRC with a constant input current of 1 A and an output current of 330 mA. [ABSTRACT FROM AUTHOR]

In this paper, a family of step-up resonant switched-capacitor converters (RSCs) with a continuously adjustable conversion ratio is proposed based on the Cuk dual-resonance core (DRC) featuring two resonant paths. By adopting the on-time fixed frequency modulation, the two resonant paths can conduct simultaneously and satisfy the charge balance of the flying capacitor during the overlapping period. As a result, the conversion ratio—upper bounded by two determined by the circuit configuration—can vary continuously and efficiently even at the light load condition (1/10 of the rated power). A comprehensive analysis—the operation principle, voltage-gain curve, and voltage/current stresses—about the DRC is given. In addition, the Cuk DRC was extended to the series–parallel switched-capacitor converter (SCC), Fibonacci SCC, and voltage doubler to form a family of step-up RSCs, whose voltage-gain curves of different topologies are derived. Moreover, a characteristic comparison between the Cuk DRC and the traditional “direct” and “indirect” resonant core is given. Then, a 48 to 62–94.6 V resonant core with peak efficiency 97.8% and maximum power 120 W under the open loop condition was built. The analyses were verified by both experimental and simulation results. [ABSTRACT FROM AUTHOR]

This paper studies the current sharing problem of a dc microgrid using the hybrid dynamic control method. The hybrid dynamic controller framework is established including a continuous-time part and a discrete-time part, where the former part eliminates the voltage deviation of the dc bus and the latter part ensures the current sharing accuracy of the dc microgrid. The proposed distributed hybrid secondary controller not only guarantees a high accuracy of current sharing but also maintains the voltage regulation at the dc bus. Different from most existing methods, it only utilizes the sampling output current information of neighbors at the discrete time instants, which greatly reduces the communication burden. Under the framework of stability analysis on the closed-loop system, the proposed hybrid dynamic controller achieves both current sharing and voltage regulation if the average interacted interval of the discrete time interaction satisfies a bounded constraint. Besides, a detailed parameter design of the controller is provided. Finally, simulation and experimental tests are presented to demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The five-level nested neutral-point-clamped (5L-NNPC) converter is one of the most promising topologies for medium-voltage (2.3–7.2 kV) high-power applications such as medium-voltage drives, wind energy conversion systems, and grid-connected systems. The 5L-NNPC requires a fewer number of switching devices, freewheeling and clamping diodes, and flying capacitors compared to the existing five-level multilevel converters. In the 5L-NNPC topology, each flying capacitor voltage is regulated at one-fourth of the dc-bus voltage to obtain the five-level operation. Due to the lack of redundant switching states, it is difficult to control the flying capacitor voltages by using the pulse-width-modulation-based classical control methods. This paper proposes a model-predictive current control (MPCC) approach to control the flying capacitor voltages along with the output currents of the 5L-NNPC converter. The discrete-time model of 5L-NNPC is developed to implement the MPCC scheme. The simulation and experimental studies are conducted to verify the dynamic and steady-state performance of 5L-NNPC with the MPCC scheme. The performance of the proposed MPCC approach is compared with the conventional space-vector-modulation-based voltage-balancing approach. Furthermore, the flying capacitor voltage control capability of MPCC is verified at different load power factors. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

This paper presents a dynamic power flow management system for a solar photovoltaic (PV) system employing a single-stage single-inductor-based dual-input/output dc–dc converter feeding standalone dc loads backed up by a rechargeable battery. A time-sharing voltage-mode control scheme has been proposed for power flow management between solar PV, a battery, and a standalone dc load, and it also maintains a constant dc load voltage and performs maximum power point tracking operation of solar PV. The implementation of the control scheme has been described in detail. The steady-state performance of the single-stage converter has been explained with the relevant analytical expressions derived along with the characteristics. A state-space average model was developed for simulating the transient behavior and validating the working of the system for step changes in the input solar PV power and the dc loads. A hardware prototype of the proposed system has been fabricated, and the proposed controller has been implemented using the dSPACE DS1103 real-time interface board. The working of the proposed scheme for different levels of input solar insolation and dc load power demand has been satisfactorily demonstrated, and the corresponding results are also provided. [ABSTRACT FROM AUTHOR]

Many of the renewable energy resources, like offshore wind, utility PV farms, are located far away from the load centers, which requires dc power transmission system to efficiently deliver power. Voltage-source converter solution is required in many applications due to the stability and compensation requirement. This paper presents a new voltage source converter topology for medium to high voltage dc application, named modular embedded multilevel converter (MEMC). MEMC is based on a three-level topology structure and consists of series-connected insulated-gate bipolar transistor (IGBT) bridge stacks, like the popular modular multilevel converter (MMC) and series-connected thyristor or press-pack high voltage integrated gate-commutated thyristor or IGBT stacks. The basic operation principle, control solutions, and the methods to commutate the thyristors are explained in detail. Due to the three-level structure, the total number of IGBT stacks are reduced by half compared with MMC, leading to much lower energy storage, weight, volume, and system complexity. Also by replacing part of the IGBT stack in MMC with thyristor stack, both of the system conduction loss and switching loss can be further reduced. There are other topology variations of MEMC with a similar operational principle but different characteristics. [ABSTRACT FROM AUTHOR]

This paper presents the development, implementation, and performance evaluation of a new active dc link for permanent magnet generator (PMG)-based wind energy conversion systems (WECSs). The proposed dc link is developed based on the multiport converter (MPC) topology with two dc–dc power electronic converters (PECs) that have separate inputs and parallel-connected outputs. The first dc–dc PEC is designed as a boost converter, while the second dc–dc PEC is designed as a flyback converter. Each dc–dc PEC is operated and controlled independently to facilitate processing continuous and/or discontinuous input dc voltages. The performance of the MPC active dc-link is experimentally evaluated using a grid-connected 7.5-kW PMG-based WECS, when operated under different wind speeds and/or levels of power delivery to the host grid. Test results show that the proposed dc link can produce a high-quality-regulated dc output voltage over a wide range of wind speeds and levels of power delivery to the host grid. Performance results also demonstrate that the operation of the MPC active dc link has minor impacts on the operation and control of the generator-side and grid-side PECs. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

In this paper, a topology using a dual-stator winding induction generator (DWIG) and a boost converter is proposed for the variable speed wind power application. At low rotor speeds, the generator saturation limits the voltage of the DWIG. Using a boost converter, higher dc voltage can be produced while the DWIG operates at maximum power point tracking even at low-speed and low-voltage conditions. Semiconductor excitation controller (SEC) of the DWIG utilizes control-winding voltage oriented control method to adjust the voltage, considering V/f characteristics. For the proposed topology, the SEC capacity and the excitation capacitor are optimized by analyzing the SEC reactive current considering wind turbine power-speed curve, V/f strategy, and the generator parameters. The method shows that the per-unit capacity of the SEC can be limited to the inverse of DWIG magnetizing reactance per-unit value. The topology is simulated in MATLAB/Simulink platform and experimented with a scaled 1 kW prototype. Both simulation and experimental results demonstrate wide variable speed operation range of the DWIG and verify the optimization. [ABSTRACT FROM AUTHOR]

This paper describes a low-complexity trajectory controller for near-optimal minimization of conduction losses in series-resonant, dual half-bridge converters (SR-DHB). The technique builds on the concept of minimum current trajectory (MCT) of a resonant converter, and formulates a piecewise-linear approximation of the MCT (PWL-MCT) for an SR-DHB topology, which can be implemented digitally via standard arithmetic operations. The low-complexity realization of such technique makes it suitable to be easily implemented in a commercial microcontroller, or even inside a custom-designed digital IC, depending on the target application requirements. Even more importantly, the MCT-based control trajectory can be formulated independently of the converter parameters, resulting in a control approach of the broadest applicability. When equipped with such simple trajectory controller, the SR-DHB converter becomes an efficient, controllable bidirectional dc–dc power unit, which can be employed in a number of scenarios, including dc power distribution systems and battery-to-battery power interfaces. Compared with traditional phase shift modulation, the proposed trajectory controller yields higher efficiency at intermediate-to-light load levels, and equal efficiency at heavy load. Furthermore, the proposed PWL-MCT concept can be implemented to accommodate wide variations in the converter voltage conversion ratio, making the resulting power unit versatile and voltage-programmable. The proposed approach is validated on a 800 W, 200 V-to-145 V, SR-DHB converter prototype. Efficiency comparisons are discussed highlighting the benefits of the PWL-MCT controller over traditional modulation approaches, and the strong efficiency improvement achievable at voltage conversion ratios away from the nominal one. [ABSTRACT FROM AUTHOR]

Model predictive control (MPC) for modular multilevel converter (MMC) systems has drawn attention among researchers in recent years due to its straightforward implementation, ability to control multiple objectives in a single cost function, and excellent dynamic response. Even though MPC seems promising for the MMC, it suffers from an excessive increase in computational complexity when the number of submodules (SMs) per arm (N) is increased. The computational load can be reduced by decoupling the SM capacitor voltage control from the cost function and balancing them in an external voltage sorting algorithm. In this paper, a further reduction of computations in the MPC is achieved by the preselection of control options that can satisfy the control objectives in the next sampling time. The preselection algorithm generates a greatly reduced number of control options to be computed by a straightforward MPC loop at each sampling time. In addition, the MPC together with the preselection algorithm can generate $2N+ 1$ output voltage levels in the MMC while maintaining a low $dv/ dt$ in the output voltage and suppressing the circulating currents in MMCs with considerable number of SMs. The steady-state and dynamic performance of the MMC operating with the proposed method is verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

High-power current sources with high dynamic performance, ultralow current ripple, and absolute reference tracking accuracy are the key elements for magnets (bumper and septum) that are used in accelerators. Similar requirements are also encountered in plasma research applications in fusion reactors, as well as plasma research for the future high voltage direct current circuit breakers. Therefore, the current source must be able to drive resistive/inductive and highly fluctuating loads without any compromise in its performance. In this paper, such a flexible, dynamic, and accurate current source is introduced, which able to provide amplitudes up to 30 kA and bipolar voltages up to 10 kV. The system’s operating concept is presented and its design procedure in order to fulfill a list of demanding specifications is demonstrated. In addition, a detailed description of its near-optimal, advanced control system is presented. Finally, the theoretical considerations are verified by extensive simulation results for various operating scenarios, including driving chaotic arc loads. [ABSTRACT FROM AUTHOR]

This paper presents a single-inductor multiple-input single-output (SI-MISO) boost converter with a deadbeat-based control method. The proposed deadbeat-based control has the capability to simultaneously conduct the power regulation from multiple inputs and the output voltage regulation for the SI-MISO boost converter. The advantages of the proposed method are less component count, lower system cost, compatibility for arbitrary number of inputs, fast response, and simplicity for implementation. Hence, the SI-MISO boost converter is a promising interface for the regulation of multiple energy sources as a standalone power system, which can be utilized in electric vehicle applications. To verify the performance of the proposed deadbeat-based control method, a laboratorial prototype of the SI-MISO boost converter is built. The steady-state and dynamic operations are investigated based on the prototype. The experimental results demonstrate that input power and output voltage of the SI-MISO boost converter can be effectively regulated by the proposed control method. The comprehensive comparison with the existing methods is conducted to further illustrate the advantages of the proposed deadbeat-based method. [ABSTRACT FROM AUTHOR]

This paper presents a new concept and approach for topology control and switching in distribution systems by extending the traditional circuit switching to laterals and single-phase loads. Voltage unbalance and other key performance indicators including voltage magnitudes, line loading, and energy losses are used to characterize and demonstrate the technical value of optimizing system topology on a per-phase basis in response to feeder conditions. The near-optimal per-phase topology control is defined as a series of hierarchical optimization problems. The proposed approach is applied to IEEE 13-bus and 123-bus test systems for demonstration, which included the impact of integrating electric vehicles (EVs) in the test circuit. It is concluded that the proposed approach can be effectively leveraged to improve voltage profiles with electric vehicles, the extent of which depends on the performance of the base case without EVs. [ABSTRACT FROM AUTHOR]

This paper presents a new predictive power-factor-correction (PFC) controller for series-interleaved three-level boost (TLB) converters. Compared to the state-of-the-art TLB PFC controllers, where a two-cycle prediction and a detection of an operating region are necessary, the proposed controller achieves a low total harmonic distortion of the input current by using a single equation to predict the input current in all operating regions of the converter, in just one operating cycle. The average current control is achieved by sampling at the peak of the triangular carrier. The proposed PFC controller significantly reduces the distortion of the input ac current near the zero-crossing points, resulting in a low total harmonic distortion of the input current. The operation of the proposed controller was evaluated, and its stability and robustness to parameter changes was confirmed analytically. The controller operating principles were verified in simulations and validated by experiments on a medium-voltage 50-kW converter prototype. [ABSTRACT FROM AUTHOR]

This paper deals with an effective power transfer scheme between the solar photovoltaic (PV) array and single-phase grid, feeding a field-oriented-controlled (FOC) permanent-magnet synchronous motor (PMSM) drive applied to a water-pumping system (WPS). Owing to the intermittency associated with solar (PV) system, the requirement of constant water supply is not possible with the standalone system. In order to mitigate this, a grid-intergraded WPS is proposed here. The grid integration enables the consumer an uninterrupted operation of water pump irrespective of solar insolation level. Moreover, the PV power can be fed to the utility grid when water pumping is not required. To make it possible, one voltage-source converter (VSC) and one voltage-source inverter connected to a common dc link are used for utility grid and PMSM control, respectively. The unit vector template theory is utilized to generate switching pulses for VSC to control the bidirectional power flow between the solar PV system and utility grid through the common dc link. A sensorless FOC is used to drive the PMSM coupled to the water pump. An intermediate stage boost converter is used for extracting optimum power from solar PV array under variable insolation. A perturb and observe algorithm is used for generating the duty ratio for the maximum power point (MPP) operation. The applicability of overall system constituting utility grid in conjugation with PV array fed PMSM-coupled water pump ensuring bidirectional power flow control with MPP tracking of PV array and abiding the utility grid, IEEE-519 standard for power factor, and total harmonic distortion is simulated in MATLAB/Simulink environment with SimPowerSystem toolbox and validated on a prototype developed in the laboratory. The system prototype is tested under variable solar insolation and grid abnormalities such as voltage sag and voltage swell. [ABSTRACT FROM AUTHOR]

This paper discusses the energization and start-up process of modular three-stage solid-state transformers (SSTs) based on a cascaded H-bridge topology. A key element of the SST is the auxiliary power supply (APS) feeding the auxiliary circuitry. Redundancy and simpler implementation can be achieved by powering the APSs from the dc-link capacitors of cells, but at the expense of a more challenging start-up process of the SST. The first step of this process must be performed before APSs are operative. This can result in undesired transient events (inrush currents, voltage sags in the capacitors voltages, etc.), which could prevent a proper start-up of the SST or even jeopardize the power devices or other elements. A simple strategy for the energization and start-up of SSTs using this APS structure is proposed. The method is valid for both grid-forming and grid-feeding operations of the SST, regardless of the energization port and without the addition of any extra circuitry. Simulation and experimental results are provided. [ABSTRACT FROM AUTHOR]

This paper investigates ac–dc–ac multilevel topologies for three-phase four-wire applications obtained from an interconnection of three-leg voltage-source converters. The topologies can be applied in line voltage regulators, universal active power filters, and uninterrupted power supplies. Operating principles, a pulsewidth modulation (PWM) technique, and an overall control strategy are developed. The PWM and control strategies are suitable to regulate the dc-link voltages and to reduce the harmonic distortion, switching stress, and power losses. Simulation results are used to compare the proposed configurations with a conventional solution in terms of harmonic distortion, semiconductor losses, and others characteristics. Experimental results are presented to validate the theoretical considerations and were obtained by using insulated-gate bipolar transistors with dedicated drives and a digital signal processor with appropriated plug-in boards and sensors. [ABSTRACT FROM AUTHOR]

In this paper, a fifth-order boost point-of-load converter is developed by cascading a modified fourth-order boost converter with a combination of L–C and diode. This topology has the following salient features: Single-switch topology, common ground between source and load, low-voltage stress across intermediate capacitors, and voltage gain same as other reported fifth-order boost converters with no common ground. Steady-state and dynamic analyses demonstrate the proposed converter's boosting feature and dynamic performance, respectively. A contoured robust Bode plot methodology is employed to design the robust voltage-mode controller to ensure load voltage regulation in the presence of uncertainties. The necessary and sufficient conditions under which the designed controller guarantees the load voltage regulation and robust stability are obtained. A step-by-step robust controller design procedure is outlined. The salient features of the proposed converter and its robust performance are studied analytically, using the MATLAB platform, and validated experimentally on a 60-W prototype module. [ABSTRACT FROM AUTHOR]

This paper investigates an ac–dc–ac multilevel power converter. The studied configuration is composed of two single-phase ac–dc–ac three-leg modules and series-connected H-bridges in the shared part of system. Because the proposed converter has shared legs between the input and output, it is employed in applications with same input and output frequency. Uninterrupted power supply and unified power quality conditioner are application examples for this converter. Such multilevel topology has lower dc-link voltage rating, which, consequently, presents low switch blocking voltages when compared to conventional topologies. System model, a space-vector pulsewidth modulation (PWM) strategy to symmetrical and asymmetrical dc-link voltages, and an overall control strategy to adjust the system variables are presented. A power flux analysis shows the operation zone in which the individual dc-link voltage balancing is possible. PWM and control strategies are developed to reduce the semiconductor total losses, harmonic distortion, and switching stress. Two ac–dc–ac multilevel conventional structures are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

The application of cascaded multilevel converters in large-scale photovoltaic plants connected to the utility grid has many advantages, such as the absence of sinusoidal filters and line-frequency transformers. Improved overall performance under partial shading conditions is possible due to the distribution of arrays among a large number of maximum power point trackers. In this situation, although the cells operate at different power levels, the three-phase currents injected into the point of common coupling must be balanced. A suitable control technique is required to achieve this goal. This paper presents a complete algorithm to handle three-phase power balance and single-phase power harvesting simultaneously. Simulation results assuming a medium-voltage system connected to a typical utility grid illustrate the dynamic and steady-state performance capability of the proposed strategy. Experimental results of a low-voltage, solid-state transformer-based, three-cell prototype are also included. [ABSTRACT FROM AUTHOR]

Hybrid boost converter (HBC) has been proposed to replace a dc/dc boost converter and a dc/ac converter to reduce conversion stages and switching loss. In this paper, control of a three-phase HBC in a Photovoltaic (PV) charging station is designed and tested. This HBC interfaces a PV system, a dc system with a hybrid plug-in electrical vehicles, and a three-phase ac grid. The control of the HBC is designed to realize maximum power point tracking for PV, dc bus voltage regulation, and ac voltage or reactive power regulation. A testbed with power electronics switching details is built in MATLAB/SimPowersystems for validation. Simulation results demonstrate the feasibility of the designed control architecture. Finally, lab experimental testing is conducted to demonstrate HBC's control performance. [ABSTRACT FROM AUTHOR]

Direct power control (DPC) has gained much attention for medium-voltage applications due to its fast power control capability. However, a conventional static switching table based DPC can lead to unsatisfactory response when the converter is connected to an electric grid because it is commonly designed assuming ideal and constant voltages of the grid and the dc link. Therefore, the actual grid voltage and the actual converter dc-link voltage should be considered while designing the switching table. This paper proposes a novel dynamic switching table for the DPC, considering actual grid and dc-link voltages variation. The proposed dynamic switching table incorporates a new definition of power influence crossover angles of each converter space vector. The proposed scheme dynamically adapts the switching table by feeding forward the actual grid and dc-link voltages, and hence the converter's power is precisely controlled. The proposed technique is verified for the three-level neutral point clamped converters connected to a standard IEEE 9-bus test system. Moreover, the real-time simulations are performed in a real-time digital simulator, OPAL-RT. The obtained results verified the effectiveness of the proposed DPC strategy under different grid fault scenarios. [ABSTRACT FROM AUTHOR]

This paper presents a need-based distributed coordination strategy (NDCS) for multiple electric vehicle (EV) storages in an islanded commercial hybrid alternating-current (AC)/direct-current (DC) microgrid. The control capacity of the interlinking converter is enhanced by incorporating combined power-droop and voltage-droop strategies to leverage the coupling of AC and DC voltages. Therefore, the AC bus voltage can be regulated simultaneously by regulating only the DC bus voltage without affecting the power-sharing capabilities of the converter. The NDCS is proposed to coordinate the EV storages to regulate the DC bus voltage. The main objective of the NDCS is to decide whether the coordination of the available EV storages is to be done in a decentralised or a distributed manner. The mathematical model and the algorithm to deploy NDCS are developed to realise its application to a real system. The effectiveness of the control system is verified in a commercial hybrid AC/DC microgrid comprising one photovoltaic unit and four EV storages directly connected to the DC bus via DC/DC converters and four distributed-generation (DG) units connected to the AC bus using the conventional droop-control scheme. The performance of both controllers is tested under variable irradiation, commercial loading, and various fault conditions. The results of the case studies demonstrate the efficacy of the overall system in terms of robustness for a variable generation-demand scenario, time delay, EV plug-and-play, and fault conditions. [ABSTRACT FROM AUTHOR]

Traditional seven-level active neutral-point-clamped (ANPC-7L) converters suffer from the problems of dynamic voltage balancing in series switches and multilevel voltage jumping of phase output voltage during switching states transition. This paper presents a novel ANPC-7L topology with auxiliary commutating branches and elaborates on its commutating strategies. The presented topology and its commutating strategies completely resolve the two problems mentioned above. The validity of the presented topology and its commutating strategies are verified by experimental results from a 380 V/5 kW ANPC-7L converter. [ABSTRACT FROM AUTHOR]

A unidirectional single-phase ac–dc–ac converter is proposed and analyzed in this paper. It is composed of paralleled rectifiers and inverters sharing two legs with two dc-link capacitor voltages. Models and a control strategy of the systems including circulating currents are developed. Compared to the conventional four-leg and three-leg (4L and 3L) single-phase ac–dc–ac converters, the proposed topology allows the decreasing of the current and power ratings of the power switches, the harmonic distortion, and semiconductors power losses. And compared to the unidirectional three-leg ac–dc–ac converter, it allows us to decrease the current and power ratings of the power switches and the harmonic distortion. In addition, a modified interleaved pulse width modulation (PWM) strategy using four-carrier PWM is presented, ensuring five-level voltage at the input and output sides of the converter. Simulation and experimental results are also presented to demonstrate the viability of the proposed circuit. [ABSTRACT FROM AUTHOR]

To enhance the redundancy and reliability for a distributed generation system, a grid-tied photovoltaic (PV) generation system based on series-connected module-integrated inverters (SC-MIIs) is presented in this paper. In the grid-tied SC-MII system, each PV panel is interfaced with an MII with independent maximum power point tracking to harvest maximum solar energy. The outputs of MIIs are at ac line frequency and are connected in series to fulfill the voltage requirement in the utility grid. Since the high step-up power conversion stage in the conventional microinverter is avoided, the grid-tied SC-MII system is easier to implement and features high efficiency. Meanwhile, a distributed control strategy for SC-MIIs is proposed, in which the active power sharing among the MIIs depends on the individual maximum power available from PV panels, while the reactive power of the system can be regulated by any of the MIIs according to the utility grid command. Simulation and experimental results verify the feasibility and effectiveness of the proposed system and its corresponding control strategy. [ABSTRACT FROM AUTHOR]

This paper proposes a novel approach to reduce the power processed by series-connected partial-power converters (S-PPC) applied to string/multistring level maximum power point tracking photovoltaic systems. A design procedure based on the definition of the voltage regulation range is presented. It introduces an additional degree of freedom that allows a proper design of the converter in order to reduce not only the active power but also the nonactive power, reducing losses and increasing power density. By means of the proposed approach, it is also demonstrated that by replacing the conventional step-up partial-power converter by a step-up/down partial-power converter, the active and nonactive power can be further reduced, allowing to better explore the benefits of the partial-power concept. In order to validate the proposed approach, two 750-W prototypes of full-bridge S-PPC and full-bridge/push–pull S-PPC were implemented and experimentally evaluated. The step-up/down prototype presented a reduction of 46.9% in nonactive power and 23.4% of its volume, resulting in a higher efficiency and power density in comparison to the voltage step-up prototype counterpart. [ABSTRACT FROM AUTHOR]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

Three-phase three-leg inverter is one of the most popular topologies for inverters. When short-circuit fault occurs, the inverter is generally switched to the current-controlled mode from voltage-controlled mode to limit the fault currents. In this situation, the inverter becomes equivalent to a symmetric, three-phase, positive sequence current source. However, the voltage limiting may occur under asymmetrical fault. In this paper, a closed-loop model based on time-domain is originally developed as a means to investigate the fault current characteristics under asymmetrical fault. Based on the proposed model, a more intuitive insight into fault currents is presented as follows. 1) The positive sequence fundamental component of three-phase currents can still track the symmetric current references. 2) The magnitude of fault phase currents (ignoring the harmonics) will vary between 1 and $\sqrt 3 $ times of magnitude of current limiting references. Based on the conclusion, although the magnitudes of fault phase currents can be reduced by adopting smaller current limiting references, the actual magnitudes of fault phase currents will still vary in a range depending on the load impendence of healthy phase. Therefore, the reliable action of the protection devices is greatly affected and the selective protection cannot be realized. Furthermore, in order to achieve completely controllable fault currents under asymmetrical fault, two alternative current limiting strategies are presented with reverse current limiting references, and with current limiting references based on the introduced phase angle regulation. The theoretical results are validated by simulations and experimental results. [ABSTRACT FROM AUTHOR]

This paper introduces a hybrid modular multilevel converter (MMC) with the full-bridge submodules (FBSMs) inserted in the ac side. It is intended for redistributing arm powers of the MMC system to reduce the submodule (SM) capacitor voltage fluctuation by injecting high-frequency powers in upper and lower arms without disturbing the output voltage. New power distribution of the hybrid MMC system can be realized by controlling the SMs and FBSMs working under the high-frequency powers. The proposed FBSMs in the hybrid MMC system also perform as the harmonic power generator to eliminate the common-mode voltages in the ac side. Since the FBSMs locate in the ac side of the hybrid MMC system, the traditional MMC control method can be directly applied in arm control of the hybrid MMC system. Meanwhile, relationship between the arm powers and SM capacitor voltage has been analyzed in detail to reduce the SM capacitor voltage ripples by redistributing the frequency spectrum of arm powers. Simulation and experimental results have also verified the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]