Search

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

Since the wide application of virtual synchronous generators (VSGs), the power grid faces great challenges in the safe and stable operation due to their limited thermal capacity and weak anti-disturbance ability. During transient period, for example, a fault occurs in the transmission line, the VSG may lose the transient angle stability and provoke the current hard limit. Even if the fault is cleared by tripping of line, it still faces the problem of instability and voltage dips. To address this problem, in this paper, the post-fault large-signal model of VSG is derived first via the travelling waves based fault information acquisition. Subsequently, with the effect of both active and reactive power loops taken into account, a two-stage simultaneous control scheme is proposed for improving the transient stability of VSG, while considering the current limitation during fault state and voltage support after fault clearance. This method is fulfilled by mode switching and an additional feedback control based on the fault signal. Finally, the effectiveness of the proposed method under both symmetrical and asymmetrical faults is verified. Moreover, the application of the proposed method in a multiple VSGs system is also verified. Besides, the robustness to parameter mismatch and the feasible operating region for the method are discussed. [ABSTRACT FROM AUTHOR]

This paper proposes a distributed coordinated voltage control scheme for distribution networks with distributed generation (DG) and on-load tap changer (OLTC). In this scheme, static synchronous compensators (STATCOMs), DG units and OLTC are coordinated to regulate voltages of all buses to be close to the nominal value in the distribution network, mitigate voltage fluctuations, and minimize the number of operations of OLTC while considering different temporal characteristics of voltage regulation devices. The optimization problem of coordinating DG units and STATCOMs is decomposed by the gradient projection (GP) method. The local controller optimizes the reactive power outputs of DGs and STATCOMs according to local voltage and reactive power measurements, and still achieves the optimal coordination of DG units and STATCOMS in a decentralized manner without a central controller or communication between local controllers. The OLTC control scheme is designed to correct the long-term voltage deviations based on model predictive control (MPC) while minimizing the number of operations. The local controllers send the calculated reactive power references of DG and STATCOMs to the OLTC controller, which achieves distributed coordinated voltage control and mitigates the computation burden. A distribution network with two 20 kV feeders and 8 DG units was used to validate the control performance of the proposed coordinated voltage control scheme. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

With increasing penetration of solar PV, some distribution feeders are experiencing highly variable net-load flows and even reverse flows. To optimize distribution systems under such conditions, the scheduling of mechanical devices, such as OLTCs and capacitor banks, needs to take into account forecasted solar PV and actual grid conditions. However, these legacy switching assets are operated on a daily or hourly timescale, due to the wear and tear associated with mechanical switching, which makes them unsuitable for real-time control. Therefore, there is a natural timescale-separation between these slower mechanical assets and the responsive nature of inverter-based resources. In this paper, we present a network admissible convex formulation for holistically scheduling controllable grid assets to position voltage optimally against solar PV. An optimal hourly schedule is presented that utilizes mechanical resources to position the predicted voltages close to nominal values, while minimizing the use of inverter-based resources (i.e., DERs), making them available for control at a faster time-scale (after the uncertainty reveals itself). A convex, inner approximation of the OPF problem is adapted to a mixed-integer linear program that minimizes voltage deviations from nominal (i.e., maximizes voltage margins). The resulting OPF solution respects all the network constraints and is, hence, robust against modeling simplifications.Simulation based analysis on IEEE distribution feeders validates the approach. [ABSTRACT FROM AUTHOR]