Search

Summary Multilevel inverters are known as essential converters in renewable sources. First, in this paper, a new submodule is presented, and based on it, a new sub‐multilevel inverter is presented. The proposed sub‐multilevel inverter consists of several unidirectional and bidirectional switches and DC voltage sources. Then, the generalized topology, developed in two modular and cascaded modes, is presented to increase production levels. The proposed submodules are connected in series in the modular topology, increasing production levels. The proposed topology to produce the maximum output levels has the minimum number of IGBTs, drivers, DC voltage sources, etc. Mathematical analyses for conduction and switching losses are provided, and mathematical analyses for the number of devices and voltage across the switches are also presented. In addition to the mathematical analysis of losses, the simulation results are also presented. A general comparison of proposed topology components is presented to demonstrate their advantages. This comparison shows that the proposed topology has the minimum number of power electronic devices. In this paper, nearest level modulation is used to control the proposed topology. The simulation and experimental results of the proposed sub‐multilevel verify the performance of the proposed topology. [ABSTRACT FROM AUTHOR]

As the penetration of distributed generation (DG) systems in the grid is increasing, the challenge of combining large numbers of DGs in the power systems has to be carefully clarified and managed. The control strategy and management concept of the interconnected systems should be flexible and reliable to handle the various types of DGs. This can be suitably met by microgrids. This paper introduces the microgrid structure and elements and states the main objectives that should be achieved by the microgrid controllers and each DG controller in both operation modes (grid‐connected and island mode). It also presents the challenges of having multiple DG units in a microgrid in terms of accurate power control/sharing, voltage and frequency regulation, power management between DGs, different renewable energy sources integration and deployment, seamless mode transfer, and the modeling issues. The centralized and decentralized control techniques as potential solutions have been discussed and compared by highlighting the advantages and disadvantages of each. Furthermore, the recent control techniques for drooped alternating current microgrids and the main proposed solutions and contributions in the literature have been exposed to finally overcome the droop control limitations and obtain a flexible and smart distributed power system. [ABSTRACT FROM AUTHOR]

Summary: With the rapid development of renewable energy, inverters have been widely used in the distributed power system. For the safety of the distributed power system, the stable operation of the inverter is vital. Hence, this paper detects slow‐scale instability fast‐scale instability and in the double‐loop proportional‐integral (PI) control single‐phase full H‐bridge inverter with inductive impedance load by the discrete‐mapping model firstly. Next, the mechanism of the mechanism slow‐scale and fast‐scale behaviors are explained by state‐space average model and Filippov method, respectively. Then, passive damping method and sine wave compensation techniques are extended to the system to suppress the nonlinear behaviors. Finally, the PLECS simulation and experiments are utilized to verify the correctness of the investigations. [ABSTRACT FROM AUTHOR]

SUMMARY In photovoltaic (PV) double-stage grid-connected inverters a high-frequency DC-DC isolation and voltage step-up stage is commonly used between the panel and the grid-connected inverter. This paper is focused on the modeling and control design of DC-DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. In the proposed overall control structure the output voltage of the DC-DC converter is regulated by the grid-connected inverter. Therefore, the inverter may be considered as a constant voltage load for the development of the small-signal model of the DC-DC converter, whereas the PV panel is considered as a negative resistance. The sensitivity of the control loops to variations of the power extracted from the PV panel and of its voltage is studied. The theoretical analysis is corroborated by frequency response measurements on a 230 W experimental inverter working from a single PV panel. The inverter is based on a Flyback DC-DC converter operating in discontinuous conduction mode (DCM) followed by a PWM full-bridge single-phase inverter. The time response of the whole system (DC-DC + inverter) is also shown to validate the concept. Copyright © 2011 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]