Search

This paper proposes a novel polygonal voltage space vector structure (SVS) having 30 sides, for a star-connected induction motor drive. The SVS eliminates the presence of harmonics up to 25th order from motor phase voltage throughout the entire modulation range, providing a torque profile devoid of lower order pulsations. Linear modulation is extended till 99.63% of base speed without exceeding the motor phase voltage rating. Topology consists of a dc-link fed primary inverter and two equal low voltage modular capacitor fed secondary inverters. Here the harmonics generated by the primary inverter is canceled by the secondary inverter which acts as a switched capacitive filter. Detailed description of the SVS generation and timing calculations are provided in this paper. Effectiveness of the proposed scheme is validated using experimental results, inverter loss calculations, and harmonic analysis. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

In low-power applications of photovoltaic (PV) systems, the transformerless grid-connected inverters have been preferred to increase the efficiency and reduce the cost, size, and power losses when they are compared to the ones with the transformer. A transformerless single-phase inverter topology with a single dc-link capacitor for the grid-connected PV systems is proposed in this paper. The proposed inverter has been simulated by using a cooperation process of the MATLAB and SPICE package programs and it has been implemented for experimental verification. The proposed inverter reduces the high-frequency common-mode leakage current caused by parasitic capacitances of PV panels, whereas it is controlled with the unipolar sinusoidal pulsewidth modulation. Also, the results show that the common-mode voltage remains constant. The efficiency of the proposed inverter has been compared to that of the most common topologies having the dc-link decoupling during the zero voltage states. This paper is accompanied by a video file demonstrating the power loss distribution in the inverter. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

This paper proposes a novel method for instantaneous balancing of neutral-point (NP) voltages with stacked multilevel inverters (MLIs) for variable-speed drives. The stacked MLI uses series-connected dc sources and NPs (connecting points of dc sources) to obtain the desired levels. The balancing of NP voltages are obtained by using a low-voltage-capacitor-fed cascaded H-bridge (CHB) per phase of a symmetrical six-phase induction machine (IM), which ensures zero current drawn from NPs (at any given instant). Since no current is drawn from NPs, the single dc-link operation with stacked capacitors is also possible. The scheme is suitable for applications, where low-voltage dc sources and batteries are stacked to form a dc link. A variable-speed operation is done using a seven-level inverter scheme for a symmetrical six-phase IM, which is formed by three dc-link stacked capacitors cascaded with two low-voltage-capacitor-fed CHBs per phase. Furthermore, the method is extended for an open-end IM to obtain a seven-level common-mode eliminated space vector structure using a single dc link. The generalization of this method for any stacked $n$ -level inverter without NP voltage deviation is also presented in this paper. The experimental results and analysis are included to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a modification of the Vienna rectifier (VR) to obtain more than three voltage levels at the DC line connection, while preserving the unity power factor at the AC grid side. The proposed unidirectional multilevel there-phase rectifier, called the “Negev rectifier”, has a reduced device count and utilizes a unique novel Time Division Multiplexed based control scheme, which makes the challenging N-level VR expansion possible. The Negev rectifier can serve as a grid interface for supplying dc voltage to multilevel inverters with 4 up to 7 voltage levels, eliminating the burden of inverter-side voltage balancing control. The Negev hardware can be constructed by two complementary topologies, making it suitable for either high current or high voltage applications. [ABSTRACT FROM AUTHOR]

A multilevel dodecagonal voltage space vector generation scheme for variable-speed drive applications with single-dc-link operation requires a large value of capacitance for cascaded H-bridge (CHB) filters, when operated at lower speeds. In existing schemes, the multilevel dodecagonal structure is obtained by cascading a flying capacitor inverter with a CHB. In this paper, a new scheme has been proposed to minimize the capacitance requirement for full speed operation by creating vector redundancies using modular and equal voltage CHBs. Also, an algorithm has been developed to optimize the selection of vector redundancies among the CHBs in order to minimize the voltage ripple of the floating capacitors. The proposed algorithm considers instantaneous capacitor voltages and phase currents for optimal selection of vector redundancies. A mathematical model for capacitor voltage deviation is presented, and the effectiveness of the proposed algorithm is verified in both the simulation and the experiment. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

Impedance-source inverters using coupled inductors have been investigated as alternatives for providing high step-up voltages. However, leakage inductances of the coupled inductors have commonly led to lower overall effectiveness, in addition to generating high dc-link voltage spikes. The latter raises voltage stresses of switches, which in turn, may reduce the power levels of the inverters. A high step-up Y-source inverter has therefore been proposed in this paper to provide a high boost with a smooth dc-link voltage ensured by proper recycling of the leakage energy. These features have been verified by comparing simulation and experimental results of an existing Y-source and the proposed inverters. Factors compared are their respective boost ratios, voltage stresses, current stresses, and dc-link voltage spikes. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

In this paper, a novel space-vector pulsewidth modulation technique for a five-level active neutral-point clamped (5L-ANPC) inverter is proposed to eliminate the common-mode voltage (CMV). For the 5L-ANPC inverter, which produces a good output voltage performance and lowdv/dt, the total 125 voltage vectors can be generated, among which the proposed scheme employs only 19 voltage vectors producing a zero CMV. Due to the limitation of voltage vectors selected, the dc-link capacitor voltages of the 5L-ANPC inverter cannot be balanced by themselves. Therefore, the capacitor voltages of the inverter should be controlled by choosing the redundant switching states appropriately. The validity of the proposed modulation scheme has been verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

The three-phase four-wire inverter with split dc-link capacitors can supply unbalanced loads. For the purpose of reducing the filter inductors, a neutral inductor could be introduced into the neutral line. This paper analyzes the operation principle of the three-phase four-wire inverter with split dc-link capacitors when a neutral inductor is introduced. It is illustrated that the neutral inductor can reduce the zero-sequence switching harmonics in the voltages between the phase-leg midpoints and the output neutral point, thus the filter inductors can be reduced. The optimized design of the neutral inductor and filter inductors is proposed with the considerations of the inductor current ripple, the ability of supplying unbalanced loads, and the total energy stored in the inductors. The equivalent circuits of the three-phase four-wire inverter with split dc-link capacitors and neutral inductor is derived in the α–β–0 frame, and the zero-axis voltage regulator is modified to suppress the third-order harmonic in the zero-sequence current caused by the deadtime of the drive signals for the power switches. Finally, the experimental results from a 9-kW prototype are provided to prove the effectiveness of the proposed optimized design of the neutral inductor and filter inductors and the control strategy of the inverter. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

Inductive power transfer (IPT) for battery charging applications has significant advantages over the traditional plug-in system. Since misalignment between the primary and secondary windings is inevitable, it is of significance to improve the misalignment tolerance of IPT systems with constant-current (CC) and constant-voltage (CV) outputs for battery charging. In this paper, the load-independent output characteristic of the hybrid topology and the function switching between CC and CV of the reconfigurable topology are analyzed. Besides, a hybrid and reconfigurable IPT system with 3-D misalignment tolerance for CC and CV outputs is proposed, simplifying or even canceling control schemes. Moreover, a novel parametric design method is given for the IPT system, which can suppress the fluctuation of the output voltage/current within a certain range of misalignment. In order to validate the performance of the proposed topology, a 1-kW prototype is built, and the corresponding experiments are carried out. In the CC/CV mode, the system can operate with the longitudinal misalignment to 50% when the load varies from 36 to 480 Ω, and the fluctuation of the output current/voltage is within 5%. Similarly, the misalignment in Y- and Z-axis is 12.5% and 33.3%, respectively. [ABSTRACT FROM AUTHOR]

Owing to low cost, small size, and low weight, transformerless inverters became prominent in single-phase grid connected photovoltaic (PV) systems. Key issues pertaining to these inverters include suppression of common mode (CM) leakage current and improvement of conversion efficiency. Achieving higher efficiency in single-phase grid-connected photovoltaic systems depends on the number of stages involved in feeding power to the grid, predominantly, if the PV array voltage is less than the peak value of the grid voltage. In this paper, an integrated dc–dc converter based grid-connected transformerless PV inverter is proposed which is aimed at maintaining high efficiency, even if the PV array voltage falls below the peak value of grid voltage (efficient operation at an extended input voltage range). A modulation strategy is discussed in order to minimize the flow of CM leakage current. Further, the efficiencies of certain transformerless inverter topologies are analyzed and compared with that of the proposed topology. Detailed simulation studies are carried out in MATLAB/Simulink environment to verify the analysis. Experimental results for a scaled down laboratory prototype are included as a proof-of-concept to validate the claims. [ABSTRACT FROM AUTHOR]

In this paper, a modular control approach has been proposed for a single- and three-phase differential-mode Ćuk inverter (DMCI) operating with a recently proposed discontinuous-modulation scheme that offers tangible performance benefits over conventional continuous modulation scheme. The modular control scheme uses a combination of a transformation and adaptive control law to meet tracking requirements in the presence of converter nonlinearity. Experimental results for the single- and three-phase DMCI are provided for startup, steady state, load transition, and total harmonic distortion using different types of loads, which validate the efficacy of the implemented modular tracking controller. Further, detailed stability of the closed-loop DMCI module is provided. [ABSTRACT FROM AUTHOR]

This paper presents a nine-level transformer-based inverter requiring only eight switches. The envisaged structure consists of two standard H-bridges fed from a single dc source. Besides, a single-phase transformer is employed to aid the process of intermediate voltage level generation. An ad-hoc pulsewidth modulation scheme based on boolean logic form equations is developed to derive the gating pulses. An effortless extension of the proposed inverter to a higher number of voltage levels is also achieved by generalizing the switching functions. Furthermore, the superior performance of the proposed topology is demonstrated through a comprehensive cost-based analysis. Finally, the validation of the proposed topology is accomplished through experiments on a down-scale prototype, and the measurement results are included. [ABSTRACT FROM AUTHOR]

In this paper, a novel platform for the single phase switched-capacitor multilevel inverters (SCMLIs) is presented. It has several advantages over the classical topologies, such as an appropriate boosting property, higher efficiency, lower number of required dc voltage sources, and other accompanying components with less complexity and lower cost. The basic structure of the proposed converter is capable of making nine-level of the output voltage under different kinds of loading conditions. Hereby, by using the same two capacitors paralleled to a single dc source, a switched-capacitor (SC) cell is made that contributes to boosting the value of the input voltage. In this case, the balanced voltage of the capacitors can be precisely provided on the basis of the series–parallel technique and the redundant switching states. Afterward, to reach the higher number of output voltage levels, two suggested SC cells are connected to each other with a new extended configuration. Therefore, by the use of a reasonable number of required power electronic devices, and also by utilizing only two isolated dc voltage sources, which their magnitudes can be designed based on either symmetric or asymmetric types, a 17- and 49-level of the output voltage are obtained. Based on the proposed extended configuration, a new generalized version of SCMLIs is also derived. To confirm the precise performance of the proposed topologies, apart from the theoretical analysis and a complete comparison, several simulation and experimental results are also given. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid pulse width modulation-based discontinuous modulation (D-HPWM) strategy with dc-link voltage balancing for a three-level neutral-point-clamped (NPC) traction inverter drive. The results are then compared with continuous-hybrid-PWM (C-HPWM) to check the performance improvement. The HPWM strategy uses both the advantages of carrier- and space-vector-based PWM strategies. The duty cycles are generated using the carrier-based strategy to reduce the computational time and complexity of the system and redundant vector states are used to keep the two dc-link capacitor voltages balanced. As discontinuous PWM (DPWM) reduces the switching losses considerably compared to the continuous PWM, the DPWM strategy is developed in this paper for the HPWM-based strategy. Detailed comparison studies are then carried out in MATLAB/Simulink and PLECS to show the conduction and switching loss distribution with change in modulation index for different power switches. A 54.0-kW surface permanent magnet synchronous machine (PMSM) is used for this simulation studies. Moreover, the total inverter loss and losses in each insulated gate bipolar transistor (IGBT) are also compared. Detailed experimental performance analysis is also carried out with a scaled down prototype of a 6.0-kW surface PMSM, NPC inverter, and real-time emulator DSpace, to show the capacitor voltage deviation with both control strategies. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a vector control strategy for independent control of two permanent-magnet synchronous motors (PMSMs) using a single four-leg inverter (4LI). An expanded two-arm modulation to obtain a balanced three-phase output voltage is described. This paper also proposes a method to compensate for the fluctuations in the neutral point voltage of two split capacitors in the dc link. The experimental results show that independent speed and position control of two PMSMs can be achieved using a single 4LI with the proposed vector control method. [ABSTRACT FROM AUTHOR]

Generally, single-stage buck–boost inverters consist of distinct circuits operating individually in buck/boost or positive/negative modes, the latter definitely leading to crossover distortion in the output current. This paper proposes a switching strategy that changes the bimodal operation of a single-stage buck–boost topology to a single-mode inverter. This is due to the consequent voltage gain that ensures that the output voltage polarity, apart from its magnitude, is an exclusive function of the duty ratio. Operational principle and salient hardware design are explained with the help of equivalent circuits. Details about the dynamic model are presented, based on which controller design is carried out for both stand-alone and grid-connected operation. Experimental results obtained from a 300-W, 110-V laboratory prototype are presented to validate the performance of the proposed switching strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a new control method of a direct ac-to-ac converter consisting of two half-bridge converters and a series-resonant circuit. This circuit converts the ac input power from the utility grid to a high-frequency ac output without any dc stage. This circuit does not require a diode bridge rectifier and, thus, makes it possible to reduce forward voltage drops and power losses in the diodes. A new switching sequence for phase-shift control is proposed to regulate the capacitor voltage in each half-bridge converter and to achieve both zero-voltage switching and synchronous rectification. The proposed phase-shift control is theoretically discussed and is also verified by experimental setup using superjunction power MOSFETs. As a result, the proposed direct ac-to-ac converter exhibits a good power conversion efficiency as high as 97.7% at the rated power of 1.3 kW. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

This paper presents a variable switching point predictive current control (VSP $^2$CC) for the quasi-Z-source inverter (qZSI). The proposed VSP $^2$CC aims to remove the output current error on the ac side, as well as the inductor current and capacitor voltage errors of the quasi-Z-source network on the dc side of the converter. Unlike the previously presented direct model predictive control (MPC) strategies for the qZSI, the proposed control scheme can directly apply the switching signals not only at the discrete time instants, but at any time instant within the sampling interval. Consequently, the shoot-through state can be applied for a shorter time than the sampling interval, resulting in lower output and inductor currents ripples. Experimental results based on field programmable gate array are provided to verify the effectiveness of the introduced control method. As it is shown, the proposed method leads to lower inductor current ripples and less output current total harmonic distortion when compared with the conventional direct MPC. [ABSTRACT FROM AUTHOR]

Traditional load regulation methods for a resonant converter mainly rely on frequency modulation. It is always a tradeoff between the design of the resonant network and the range of load. Especially for wireless power transfer (WPT) systems, the resonant network usually has a high quality factor. Small variation on frequency leads to huge drop in gain and efficiency. Due to this problem, many WPT systems are unregulated and they need one or two more front-end stages to regulate the dc bus voltage and perform power factor correction (PFC). In order to lower the cost and complexity of two- or three-stages structure, a single-stage solution with a silicon carbide (SiC) based Z-source resonant converter (ZSRC) was recently proposed. The Z-source network provides high reliability as being immune to shoot-through problems. Additionally, a ZSRC can boost the dc bus voltage while the traditional voltage-source inverter can only produce a lower voltage. However, the load regulation of this new topology has not been addressed. Two effective load regulation methods with constant frequency are presented for this SiC-based ZSRC specifically. Operation principle of the two load regulation methods are described in this paper. Experimental results based on a 200-W scale-down prototype with a full-bridge series resonant dc–dc converter are presented to illustrate the mechanism of these two methods. [ABSTRACT FROM AUTHOR]

This paper presents an optimized topology for a \text3-\phi three-level inverter with complete elimination of common-mode voltage (CMV). The proposed multilevel inverter (MLI) configuration is realized by modifying a T-structure \text3-\phi inverter. The proposed configuration is an optimized solution with respect to the pulse-width modulation strategy used for CMV elimination. The given three-level inverter structure uses only 16 power semiconductor switches, which is much lower than the existing configurations. A reduced number of power semiconductor devices results in a diminished number of driver circuits, less installation space, and low cost. Further, due to the complete elimination of CMV, the proposed MLI is free from issues such as electromagnetic interference and leakage current with a reduction in filter requirement. The presented topology is also compared with other existing topologies to prove its advantage. It is an optimized solution with respect to the dc bus voltage requirement and the total voltage rating of the devices or the components used in the system. Simulation and experimental results are presented to confirm the capability of the proposed MLI. [ABSTRACT FROM AUTHOR]

A novel hybrid five-level voltage-source converter for high-efficiency applications is investigated in this paper. Compared with traditional multilevel converters, this hybrid multilevel converter generates desired staircase voltage levels with a reduced number of power devices and isolated drivers at higher voltage levels. It has redundant switching state combinations in hybrid multilevel converter, which makes it easy to balance flying capacitor voltages and realize fault-tolerant operation. A voltage-balancing control strategy based on switching state redundancies is presented for the hybrid multilevel converter to generate desired levels and also keep voltage balance of flying capacitors at the same time. The performance of the hybrid multilevel converter under various operating conditions is investigated in MATLAB/Simulink. The effectiveness of the proposed hybrid multilevel converter is validated by experiment results. [ABSTRACT FROM AUTHOR]

In signal injection sensorless drives, the injection voltage cannot be reduced under a certain value. The lower limit of the injection voltage is mainly enforced by the inverter nonlinearity that causes distortion of the injection voltage and degradation of the position estimation performance. After analyzing the inverter nonlinearity during the voltage injection, it is revealed that parasitic capacitances of insulated-gate bipolar transistors have positive effects on inverter output linearity and sensorless control. Based on this analysis, this paper proposes a method to reduce the injection voltage by connecting additional capacitors to the output terminals of the inverter. Simulation and experimental results are provided to verify the effectiveness of the proposed idea. In the experiments, using the capacitor-integrated inverter, it is shown that the injection voltage can be reduced by more than half without degrading the position estimation performance. [ABSTRACT FROM AUTHOR]

This paper presents a single-phase ac power supply circuit that based on modified voltage-fed quasi-Z-source inverter topology; it suits to the light or the heavy load and is fit for the resistive, inductive, or capacitive load. The topology, operating principle, voltage gain, control method, and its realization by DSP are described in this paper. The feasibility and rationality of the system is verified by the simulation and experimental results. [ABSTRACT FROM PUBLISHER]

As penetration of distributed generation increases, the electrical distribution networks may encounter several challenges mainly related to voltage control. The situation may deteriorate in case of a weak grid connected to an intermittent source such as photovoltaic (PV) generation. Fast varying solar irradiance can cause unacceptable voltage variations that may not be easily compensated by slow-responding utility equipment. The PV inverter can be used to control the grid voltage by injecting/absorbing reactive power. A small-signal model is derived in order to study the stability of a PV inverter exchanging reactive power with the grid. This paper also proposes a method that utilizes the available capacity of the PV inverter to support the grid voltage without violating the rating of the inverter and the maximum voltage that the inverter's switching device can withstand. The method proposed in this paper is validated using PSCAD/EMTDC simulations. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper discusses the implementation of level-shifted and phase-shifted carrier-based modulation methods, in conjunction with a multiphase open-end winding drive topology. The considered drive is supplied using two five-phase two-level voltage source inverters (VSIs), with input provided from two isolated supplies of equal dc voltages. The topology is known to yield the same space-vector pattern as a corresponding three-level inverter in single-sided supply mode. It is shown in this paper that, with the application of a simple logic, the same phase voltage waveforms result as those obtainable with the appropriate carrier-based modulation scheme applied to the three-level VSI in single-sided supply mode. While the outcomes of the modulation techniques are the same, the open-end winding topology offers certain advantages, such as modularity and absence of capacitor voltage balancing requirements. The analysis is conducted for selected modulation methods using voltage and current waveforms, spectra Fast Fourier Transform (FFT), and total harmonic distortion as figures of merit. Theoretical considerations are verified by means of simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper focuses on the common dc-link voltage between a three-phase diode rectifier and a modular multilevel cascade inverter based on double-star chopper cells (MMCI-DSCC) for a medium-voltage motor drive. This motor drive can be operated even when no capacitor exists on the dc link. However, a nonnegligible, but predictable, amount of switching-ripple voltage occurs on the dc link. This paper achieves modeling and analysis of the switching-ripple voltage, thus making it possible to design a small-sized dc passive filter consisting of series connection of a film capacitor and a damping resistor. A 400-V, 15-kW down scaled system is used to confirm the effectiveness of the analysis and the dc filter. Experimental results show that the switching-ripple voltage can be attenuated satisfactorily by the dc filter, and that the power loss dissipated in the damping resistor is negligible, compared to the rated power of 15 kW. [ABSTRACT FROM AUTHOR]

This paper proposes and analyzes a new power electronics circuit topology for wireless inductive power transfer application using current-fed half-bridge converter with CCL-LC resonant network. The major focus is analysis and implementation of a new current-fed resonant topology with current-sharing and voltage doubling features. Generally, inductive power transfer circuits with current fed converter use parallel CL resonant tank to transfer power effectively through air gap. However, in medium power application, this topology suffers from a major limitation of high voltage stress across the inverter semiconductor devices owing to high reactive power consumed by loosely coupled coil. In proposed topology, this is mitigated by adding a capacitor in series with the coil developing series-parallel CCL tank. The power flow is controlled through variable frequency modulation. Soft-switching of the devices is obtained irrespective of the load current. For grid-to-vehicle or solar-to-vehicle, the converter is analyzed and detailed design procedure is illustrated. Experimental results are presented to verify the analysis and demonstrate the performance. [ABSTRACT FROM AUTHOR]

Multilevel inverters are receiving more attentions nowadays as one of preferred solutions for medium- and high-power applications. As one of the most popular hybrid multilevel inverter topologies, the five-level active-neutral-point-clamped inverter (5L-ANPC) combines the features of the conventional flying-capacitor type and neutral-point-clamped (NPC) type inverter and was commercially used for industrial applications. In order to further decrease the number of active switches, this paper proposes a seven-switch 5L-ANPC (7S-5L-ANPC) topology, which employs only seven active switches and two discrete diodes. The analysis has shown a lower current rating can be selected for the seventh switch under high power factor condition, which is verified by simulation results. The modulation strategy for 7S-5L-ANPC inverter is discussed. A 1 kVA single-phase experimental prototype is built to verify the validity and flexibility of the proposed topology and modulation method. [ABSTRACT FROM AUTHOR]