Search

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

This paper presents the design and construction of a sample of Marx pulsed generator based on boost converter (BC) pulse-forming networks (BCPFNs). BCPFN is used instead of the conventional Marx floors for constructing this pulsed generator. BCPFN is carried out by connecting inductors and capacitors in series and parallel modes, respectively, by using solid-state switches, and during this procedure the pulsed generator converts to BC temporarily and increases the voltage of capacitors uniformly to a considerable value. This technique causes an increase in the discharging voltage level to the load that is many times more than its dc voltage source by charging the capacitors to a greater level. In order to take advantage of the benefits of Marx generator and PFN, this paper suggests a new circuit with the minimum number of switches. It means, to compose BCPFN and Marx, we have tried to design the circuit with fewer switches and instead of it we have achieved our desired performance with changing the operating mode in the states of BC, PFN, BCPFN, and BCPFN Marx. The results are simulated with MATLAB software. At the end, the experimental results of the construction of the above-mentioned system at low-power levels are presented, and the topology’s accuracy is proved by comparing them to the results of simulation. [ABSTRACT FROM AUTHOR]

Tap changers are commonly used to maintain the limits in medium-voltage lines. Initially based on electromechanical switches, efforts have been made since the 1990's to reduce maintenance expenses with thyristor-based versions. Among the methods to limit the short-circuiting current in commutating taps, the multiwinding coil has demonstrated, during decades of use in the low-voltage field, to be reliable and cheap. Two previous papers showed that multiwinding changers can be applied to medium-voltage lines up to 34.5 kV, 15 MVA with no parallel or series thyristor association. This paper proposes a new topology, based on a double array of tap switches per phase, allowing for step-up the power from 15 to 36 MVA and insertion in any point of the line with no connection to the head transformer. A comparative cost analysis gives technical and economical results for a typical 10 MVA, 34.5 kV stabilizer demonstrating the advantages of the proposed circuit over the electronic single array topology and the classic mechanical solutions. [ABSTRACT FROM PUBLISHER]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

Microinverters require high voltage gain capability for interfacing the low dc voltage output of photovoltaic (PV) module to single-phase ac grid. A two-stage nonisolated inverter is proposed in this paper, with a first boost stage and a second traditional pulse width modulated grid-tied inverter stage. The proposed boost stage consists of a coupled inductor added with a voltage multiplier to achieve the required high voltage gain at high efficiency and to operate over a wide input voltage range. Among the coupled inductor topologies, adding a clamp circuit is a common solution to limit the voltage spike caused by leakage inductance. In the proposed converter, the resonance between the coupled inductor and voltage multiplier is used to address the issue of voltage spike, thereby reducing both component count and device voltage stress. Detailed analysis and design procedure of the proposed converter is presented in this paper. Experimental results of a 250-W microinverter are presented to validate the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a new bidirectional resonant dc–dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc–dc converters, and meanwhile achieves high efficiency throughout the wide range of operation voltage. It is achieved by configuring a full-bridge mode and a half-bridge mode operation during each switching cycle. A fixed-frequency phase-shift control scheme is proposed and the normalized voltage gain can be always from 0.5 to 1, regardless of the load. The transformer root-mean-square (rms) currents in both the forward and reverse power flow directions have a small variation with respect to the voltage gain, which is beneficial to the conduction losses reduction throughout a wide voltage range. Moreover, the power devices are soft-switched for minimum switching losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology and analysis are verified with experimental results obtained from a 1-kW converter prototype. [ABSTRACT FROM PUBLISHER]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

DC–DC converters are expected to interconnect High Voltage Direct Current (HVDC) grids with different configurations or voltage levels, which will increase reliability and operational flexibility. The dc Modular Multilevel Converter (DC-MMC) is suggested as a potential non-isolated topology for HVDC applications. This paper presents an energy-based closed-loop control for the DC-MMC. Such control structure provides a full control of the current components, while ensuring energy balancing in normal and fault operation. First, the converter configuration is described and the fundamental equations are presented. Then, the normal operation of the converter is explained from the steady state conditions and the energy and current components. A closed-loop control is designed to ensure a proper dynamic response, balance the internal energies of the converter, and minimize the ac circulating current. Also, the control structure is modified to ensure dc fault ride through capability. Simulation results in MATLAB/Simulink are used to validate the converter control under normal operation and DC faults. [ABSTRACT FROM AUTHOR]

In this paper, a dual half-bridge LLC resonant converter with magnetic control is proposed for the battery charger application. The primary switches are shared by two LLC resonant networks, and their outputs are connected in series. One of the LLC resonant converters is designed to operate at the series resonant frequency, which is also the highest efficiency operating point, and the constant output voltage characteristic is achieved at this operating point. The second LLC resonant converter adopts magnetic control to regulate the total output current and voltage during both constant current charge mode and constant voltage charge mode. Meanwhile, the function decoupling idea is adopted to further improve the system efficiency. The significant amount of the power is handled by the LLC resonant converter operating at the series resonant frequency, whereas the second LLC resonant converter fulfills the responsibility to achieve closed-loop control. By carefully designing the resonant networks, the zero-voltage switching for primary switches and zero-current switching for secondary diodes can be achieved for whole operation range. A 320-W experimental prototype is built to verify the theoretical analysis, and the maximum efficiency is measured about 95.5%. [ABSTRACT FROM AUTHOR]

Load-independent output characteristics of inductive power transfer (IPT) systems are increasingly popular in battery charging. This paper proposes a novel variable-parameter T-circuit (VT) for an IPT system charging a battery with constant current (CC) or constant voltage (CV) output. The VT can transfer a CC/CV input to a CC or CV output by using an ac switch and a passive component (inductor or capacitor). An IPT system with a VT for CC–CV charging can reduce the number of passive components and ac switches. Besides, the proposed VT merits more design freedom of charge current/voltage with the constraints imposed by the loosely coupled transformer parameters compared to that of the traditional one. In addition, there are three kinds of VTs for various IPT charging systems with different requirements. A 400 W laboratory-scale prototype with a 150 mm air gap was built to verify the theoretical analyses. Both electronic load and lead-acid battery are utilized to verify the charging profile of the proposed method. The experimental results of the IPT system indicate that the fluctuation of the charging current in CC mode is less than 2%, and the change rate of charging voltage in CV mode is within 2.9%. The maximum overall efficiency 93.93% of the charging system is achieved from a dc 110 V input to a dc 100 V output. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

The three-level full-bridge (TLFB) dc−dc converter has been widely used in high-voltage, high-power applications. In the experimental test, the neutral-point voltage deviation appears; moreover, it has also been found out that if the flying capacitors are introduced, the input capacitor voltages could realize self-balance even if no active balancing solutions are adopted. In the previous publications, the role of flying capacitors is generally considered to extend the range of soft switching; however, the self-balance ability has not been mentioned or investigated in any publications thus far. In order to fill this gap, this paper provides the detailed mode operation analysis of the TLFB converter and reveals the cause of the imbalance. In addition, the mechanism of the self-balance ability provided by the flying capacitors is explained in detail, which gives a deep insight into the converter. At last, the influence factor of the voltage error in steady state has been analyzed, and the specific expression of the voltage error is also derived. The feasibility of the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

In order to provide high and extendable power levels for inductive power transfer (IPT) system, a parallel multi-inverter system based on modular inverter is presented. Various power requirements can be implemented by an adjustment of the number of paralleled inverters, which provides a high modularity. A master−slave scheme is employed for the switching-driver signals of parallel inverters, where one acts as a leader while others act as followers. Despite the master−slave scheme, the proposed circuit topology has natural robustness because of the equality in terms of the hardware configuration of each modular inverter. For proper parameters, the output phase (current lagging corresponding voltage) of an inverter is lower than the average of output phase of all inverters, when its output voltage lags behind others, and vice versa. Based on this approach, PI controllers are designed to implement phase synchronization for output voltages of all inverters. An IPT prototype supplied by the proposed parallel multi-inverter with three inverters was designed, built, and tested. Experiments show that the proposed parallel multi-inverter system has not only good circulating current suppression capacity but also excellent performance of phase synchronization. The maximum dc−dc efficiency was 94% at a 35.1 kW receiving power. This paper is accompanied by a Matlab/Simulink file demonstrating phase synchronization control. [ABSTRACT FROM AUTHOR]

This paper contains a comparison between three topologies of a three-phase two-level inverter: A quasi-Z-source inverter (qZSI), a voltage-source inverter with a boost converter and a voltage-source inverter with an interleaved boost converter. experimental results obtained from laboratory tests of equivalent 6-kW 100-kHz inverters based on SiC mosfets and Schottky diodes are provided. The following parameters are compared: Quality of input inductor current and output phase voltage as well as total power losses in the inverters. The results for these parameters are obtained for input voltage ranging from 325 V to almost 600 V (where feasible), for two sets of equivalent modulation methods (two regular methods and two reduced-loss methods), for a couple of characteristic values of deadtime and for the operation both at the maximum value of modulation index and at equal values of voltage across the inverter bridge. Results of the experiments show that the qZSI topology may, at certain conditions, surpass the traditional two-stage inverter topologies in the areas of input inductor current quality, output voltage quality and also power losses (at high values of input voltage). What is needed to obtain that is a careful examination of operating conditions, applied modulation method and deadtime value. [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

In the context of reducing total CO $_2$ emissions as well as reducing the total copper cable length and weight on cars, automotive manufacturers propose to derive all the supply voltages from a single $\text{48 V}$ bus through high step-down ratio dc–dc converters. The series capacitor tapped inductor (SCTI) converter is a promising topology for efficient single-stage step-down conversion from the $\text{48 V}$ bus. In the synchronous version of the SCTI, however, turn-off of the synchronous rectifier at positive drain-to-source current leads to a voltage spike and to a potential catastrophic failure of the converter. In this paper, a simple control technique is proposed, which prevents the foregoing condition to occur. The approach enables a reliable operation of the synchronous SCTI topology without disrupting its main features and advantages, and eliminating the need for additional snubbers, voltage clamps or auxiliary windings. The approach is validated via computer simulations and experimental tests on a $\text{48}$ -to- $\text{1.5}\;\text{V}$ , $\text{4 A}$ SCTI converter prototype. [ABSTRACT FROM AUTHOR]

For the conventional PFC rectifiers, the high efficiency cannot be achieved over a wide input range, and the efficiency will be greatly decreased at low-input voltages. In order to overcome the efficiency bottleneck under low-line input, a flexible mode bridgeless boost power factor correction (PFC) rectifier is proposed in this paper. According to the input voltage, the proposed rectifier can be flexibly adapted to the suitable operating mode to obtain the maximum efficiency. Meanwhile, the circuit components can be reused by different operating modes, so the extra cost is low. In the proposed rectifier, a back-to-back bridgeless boost PFC topology is adopted at high-line conditions and a three-level bridgeless boost PFC topology is rebuilt to reduce the switching losses at low-line conditions. Compared with the traditional bridgeless boost PFC rectifier, an extra low-voltage bidirectional switch (usually composed of two switches) is added, so the increased cost is low. In addition, the low common-mode noise can be achieved at both high- and low-line conditions due to the direct connection between the input mains and the output electrolytic capacitor. The detailed principle analysis about the proposed rectifier is presented in this paper. Finally, an experimental prototype is built to verify the feasibility and the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, the Z-source converter is introduced to power factor correction (PFC) applications. The concept is demonstrated through a wireless power transfer (WPT) system for electric vehicle battery charging, namely Z-source resonant converter (ZSRC). Due to the Z-source network (ZSN), the ZSRC inherently performs PFC and regulate the system output voltage simultaneously, without adding extra semiconductor devices and control circuitry to the conventional WPT system such as conventional PFC converters do. In other words, the ZSN can be categorized as a family of the single-stage PFC converters. In addition, the ZSN is suitable for high-power applications since it is immune to shoot-through states, which increases reliability and adds a boost feature to the system. The ZSRC-based WPT system operating principle is described and analyzed in this paper. Simulations and experimental results based on a 1-kW prototype with 20-cm air gap between the system primary and secondary sides are presented to validate the analysis and demonstrate the effectiveness of the ZSN in the PFC of the WPT system. [ABSTRACT FROM PUBLISHER]

A nonisolated ultra-high step-down interleaved dc–dc converter with low voltage stress and common ground between the input and output ports is proposed in this paper. In order to extend the extremely narrow duty cycle, series capacitors and transformers are applied to the four-phase interleaved buck converter. In addition to extending the duty cycle, the series capacitors clamp the voltage stress across the switches and diodes, which results in using low voltage rating semiconductor components. Additionally, the main switches are turned on under a soft-switching condition. Hence, the conduction and switching losses are reduced and the overall efficiency of the designed converter is improved. Other important strengths of this topology are very low output current ripple due to interleaving and automatic uniform current sharing. The validity of theoretical analysis and converter operation is confirmed by the implementation of a 150 W prototype at 400 V input voltage and 12 V output voltage. [ABSTRACT FROM AUTHOR]

In this paper, a modified asymmetric half-bridge (AHB) isolated converter is proposed, which does not have dc current offset in the transformer. The topology operates in the same way as the conventional half-bridge (HB), using asymmetric pulsewidth modulation with constant frequency. A voltage doubler rectifier is used in the output stage, which avoids the flow of the dc component current in the primary side of the transformer. In order to investigate the application of the proposed topology, a parallel-resonant (PR) version of the modified AHB was tested, which uses the parasitic elements of the transformer, such as the leakage inductance and the winding capacitance, to achieve zero voltage switching in the primary side switches over a wide load range. Theoretical and commutation analysis results are reported and design guidelines are presented herein. Experimental data were obtained from a parallel resonant 1-kW prototype, operating with a 50 kHz switching frequency, 400 V input voltage, and 400 V output voltage, to verify the theoretical study, and 97% efficiency was achieved. The proposed solution was also tested at high voltage, operating with a rated power of 1.8 kW, switching frequency of 50 kHz, input voltage of 400 V and series-connected output voltages, the maximum voltage being 8620 V. [ABSTRACT FROM AUTHOR]

A novel bidirectional dc–dc converter having high voltage gain capability with high efficiency is proposed in this paper for interfacing storage in a range of applications. The proposed converter steps up (boost) the voltage in one direction while stepping it down (buck) in the other direction of operation. An attractive feature of the proposed converter is the symmetry of its operating modes. It also has inherent soft-switching capability during turn on of the switches, enabling high switching frequency operation. This, coupled with the fact that the proposed converter uses only one coupled inductor for both boost and buck modes, leads to a compact system. A clamped capacitor network is used to recover the leakage energy. Circuit description, design, and loss calculations for both buck and boost modes are explained. The bidirectional converter is designed for a voltage gain of 10 and (1/10) in the boost and buck modes, respectively. A 500 W laboratory prototype of the proposed converter has been developed and tested under rated conditions. Even for a large voltage gain of 10, a peak efficiency in excess of 94% is achieved, which is not possible with conventional converters. All the results of this work are included. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

A switching-capacitor-based buck–boost converter (with common ground) for point of load applications is proposed in this paper. It is capable of operating in stand-alone buck or boost mode in addition to its primary operation of performing the buck–boost conversion. The striking feature of the proposed converter is low source current ripple content irrespective of its mode of operation (buck–boost, buck, or boost). First, feasible pulsewidth modulation schemes for the proposed converter are identified and thereafter the corresponding circuit performance analysis, steady-state analysis, and state-space modelling is established. Through steady-state analysis, voltage gain expressions are formulated and equations defining L-C components are derived in terms of their ripple quantities. The state-space models are used to formulate small-signal analysis and to obtain the relevant transfer functions required in the controller design. A voltage-mode/current-mode controller is designed, with a tradeoff in bandwidth, to control the proposed converter and transit it from buck to boost mode or vice versa seamlessly. A 30–55 W, 100 kHz, prototype point of load converter with 36-V input dc source is built to supply power at constant load voltage of either 48 or 28 V. The proposed converters’ effectiveness is demonstrated experimentally in terms of reduced source current ripple along with seamless transition from buck to boost mode and vice versa. [ABSTRACT FROM AUTHOR]

A new single-switch high step-up dc–dc converter is proposed, in this paper, for fuel cell vehicles. The proposed topology utilizes an L2C3D2 network to obtain high voltage gain and reduce the voltage stress on the power switch. Additionally, the proposed converter has a universal input voltage in order to suit the soft output characteristics of the fuel cell. Comprehensive analyses of the steady-state operation in continuous conduction mode and discontinuous conduction mode, and design considerations of the proposed converter are given. Finally, a 400 V/1.6 kW scaled-down prototype is developed to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

In this paper, a family of step-up resonant switched-capacitor converters (RSCs) with a continuously adjustable conversion ratio is proposed based on the Cuk dual-resonance core (DRC) featuring two resonant paths. By adopting the on-time fixed frequency modulation, the two resonant paths can conduct simultaneously and satisfy the charge balance of the flying capacitor during the overlapping period. As a result, the conversion ratio—upper bounded by two determined by the circuit configuration—can vary continuously and efficiently even at the light load condition (1/10 of the rated power). A comprehensive analysis—the operation principle, voltage-gain curve, and voltage/current stresses—about the DRC is given. In addition, the Cuk DRC was extended to the series–parallel switched-capacitor converter (SCC), Fibonacci SCC, and voltage doubler to form a family of step-up RSCs, whose voltage-gain curves of different topologies are derived. Moreover, a characteristic comparison between the Cuk DRC and the traditional “direct” and “indirect” resonant core is given. Then, a 48 to 62–94.6 V resonant core with peak efficiency 97.8% and maximum power 120 W under the open loop condition was built. The analyses were verified by both experimental and simulation results. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents an overview of resonant and hybrid switched-capacitor converters with a particular focus on multimode operation. The multimode approach is discussed as a tool to affect high efficiency and power density across a wide load range, provide variable regulation, and, as a general framework, to conceptualize the advantages and opportunities of the approach compared to more traditional dc–dc converters. A general analysis is provided to quantify the advantage of hybrid and resonant converters that factors in the tradeoffs between size and loss in the magnetic component and voltage stress on the active devices. A broader set of operating modes is presented that spans continuous and discontinuous conduction and includes resonant, quasi-resonant, and more traditional buck- or boost-like operation. A prototype flying-capacitor multilevel converter is presented to demonstrate the variety of operating modes and motivate important considerations such as voltage balance on the flying capacitors. [ABSTRACT FROM AUTHOR]

The trend toward higher switching frequencies and higher power densities in dc–dc conversion led the designers to rediscover resonant topologies. However, the analysis of these converters is often limited to a particular operating mode and/or topology. This paper wants to fill the gap by presenting a state-space-based analysis for a broad class of series-resonant converters including voltage-fed as well as current-fed topologies, either unidirectional or bidirectional. The proposed solution consists of a mathematical framework that solves the trajectory of state variables in the resonant tank, as well as the main characteristic functions such as voltage conversion ratio and transferred power. The matrix approach permits a flexible and compact formulation and easy implementation in computational tools such as MATLAB. The theoretical framework is applied to both voltage-fed and current-fed resonant topologies: the first is used to show the advantages of the proposed model respect to the first harmonic approximation, while a detailed analysis in terms of operating mode boundaries, delivered power, and voltage gain is provided for the second. Simulations and measurements on a 300-W prototype of the current-fed topology are used to validate the correctness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper presents a dynamic power flow management system for a solar photovoltaic (PV) system employing a single-stage single-inductor-based dual-input/output dc–dc converter feeding standalone dc loads backed up by a rechargeable battery. A time-sharing voltage-mode control scheme has been proposed for power flow management between solar PV, a battery, and a standalone dc load, and it also maintains a constant dc load voltage and performs maximum power point tracking operation of solar PV. The implementation of the control scheme has been described in detail. The steady-state performance of the single-stage converter has been explained with the relevant analytical expressions derived along with the characteristics. A state-space average model was developed for simulating the transient behavior and validating the working of the system for step changes in the input solar PV power and the dc loads. A hardware prototype of the proposed system has been fabricated, and the proposed controller has been implemented using the dSPACE DS1103 real-time interface board. The working of the proposed scheme for different levels of input solar insolation and dc load power demand has been satisfactorily demonstrated, and the corresponding results are also provided. [ABSTRACT FROM AUTHOR]

This paper presents a new predictive power-factor-correction (PFC) controller for series-interleaved three-level boost (TLB) converters. Compared to the state-of-the-art TLB PFC controllers, where a two-cycle prediction and a detection of an operating region are necessary, the proposed controller achieves a low total harmonic distortion of the input current by using a single equation to predict the input current in all operating regions of the converter, in just one operating cycle. The average current control is achieved by sampling at the peak of the triangular carrier. The proposed PFC controller significantly reduces the distortion of the input ac current near the zero-crossing points, resulting in a low total harmonic distortion of the input current. The operation of the proposed controller was evaluated, and its stability and robustness to parameter changes was confirmed analytically. The controller operating principles were verified in simulations and validated by experiments on a medium-voltage 50-kW converter prototype. [ABSTRACT FROM AUTHOR]

In this paper, a fifth-order boost point-of-load converter is developed by cascading a modified fourth-order boost converter with a combination of L–C and diode. This topology has the following salient features: Single-switch topology, common ground between source and load, low-voltage stress across intermediate capacitors, and voltage gain same as other reported fifth-order boost converters with no common ground. Steady-state and dynamic analyses demonstrate the proposed converter's boosting feature and dynamic performance, respectively. A contoured robust Bode plot methodology is employed to design the robust voltage-mode controller to ensure load voltage regulation in the presence of uncertainties. The necessary and sufficient conditions under which the designed controller guarantees the load voltage regulation and robust stability are obtained. A step-by-step robust controller design procedure is outlined. The salient features of the proposed converter and its robust performance are studied analytically, using the MATLAB platform, and validated experimentally on a 60-W prototype module. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

A quasi-Z-source inverter (qZSI) could achieve buck/boost conversion as well as dc to ac inversion in a single-stage topology, which reduces the structure cost when compared to a traditional two-stage inverter. Specifically, the buck/boost conversion was accomplished via shoot-through state which took place across all phase legs of the inverter. In this paper, instead of using traditional dual-loop-based proportional integral (PI)-P controller, a type 2 based closed-loop voltage controller with novel dc-link voltage reference algorithm was proposed to fulfill the dc-link voltage tracking control of a single-phase qZSI regardless of any loading conditions, without the need of inner inductor current loop. A dc–ac boost inverter with similar circuit parameters as a qZSI was used to verify the flexibility of the proposed controller. The dynamic and transient performances of the proposed controller were investigated to evaluate its superiority against the aforementioned conventional controller. The integrated proposed controller and qZSI topology was then employed in static synchronous compensator application to perform reactive power compensation at the point of common coupling. The effectiveness of the proposed approach was verified through both simulation and experimental studies. [ABSTRACT FROM AUTHOR]

This paper investigates power shunt filter topologies composed of three standard three-leg converters applied in either three or four-wire system. Compared with the usual three-phase shunt filter, the proposed ones allow us to reduce dc-link voltages, harmonic distortion or/and the semiconductor losses, and fault tolerant operation. Suitable control strategies to adjust filter and circulating currents, as well as the three dc-link voltages are presented. Two pulse-width modulation techniques are developed for the proposed topologies in order to achieve the best voltage-pulse pattern. Comparisons between these techniques are carried out in this paper. Simulation and experimental results are presented to validate the theoretical approach. [ABSTRACT FROM PUBLISHER]

New advanced power conversion systems play an essential role in the extension of range and life of batteries. This paper proposes a new modular multilevel converter with embedded electrochemical cells that achieves very low cell unbalancing without traditional balancing circuits and a negligible harmonic content of the output currents. In this new topology, the cells are connected in series by means of half-bridge converters, allowing high flexibility for the discharge and recharge of the battery. The converter features a cell balancing control that operates on each individual arm of the converter to equalize the state of charge of the cells. The paper shows that the proposed control does not affect the symmetry of the three-phase voltage output, even for significantly unbalanced cells. The viability of the proposed converter for battery electric vehicles and the effectiveness of the cell balancing control are confirmed by numerical simulations and experiments on a kilowatt-size prototype. [ABSTRACT FROM AUTHOR]

Leakage current minimization is one of the most important considerations in transformerless photovoltaic (PV) inverters. In the past, various transformerless PV inverter topologies have been introduced, with leakage current minimized by the means of galvanic isolation and common-mode voltage (CMV) clamping. The galvanic isolation can be achieved via dc-decoupling or ac-decoupling, for isolation on the dc- or ac-side of the inverter, respectively. It has been shown that the latter provides lower losses due to the reduced switch count in conduction path. Nevertheless, leakage current cannot be simply eliminated by galvanic isolation and modulation techniques, due to the presence of switches' junction capacitances and resonant circuit effects. Hence, CMV clamping is used in some topologies to completely eliminate the leakage current. In this paper, several recently proposed transformerless PV inverters with different galvanic isolation methods and CMV clamping technique are analyzed and compared. A simple modified H-bridge zero-voltage state rectifier is also proposed, to combine the benefits of the low-loss ac-decoupling method and the complete leakage current elimination of the CMV clamping method. The performances of different topologies, in terms of CMV, leakage current, total harmonic distortion, losses and efficiencies are compared. The analyses are done theoretically and via simulation studies, and further validated with experimental results. This paper is helpful for the researchers to choose the appropriate topology for transformerless PV applications and to provide the design principles in terms of common-mode behavior and efficiency. [ABSTRACT FROM AUTHOR]

Electric bicycles (EBs) are becoming increasingly popular in some regions such as China and Europe. However, wireless power transfer (WPT) for charging massive EBs poses a challenge related to the cost of WPT system (WPTS), especially in China, where EBs application is so sensitive to the product price. This paper presents an optimization method of the passive components for the S-LCC topology to decrease the cost of the overall system. With the novel method, the number of passive components can be optimized to the minimum and still with constant current and constant voltage outputs. A novel compensation method with an inductor array is also proposed to guarantee an inductive input impedance of WPTS, achieving soft switching and reducing the high switching losses of the high-frequency inverter (HFI). To demonstrate the validity of the proposed methods, an experimental setup is built. The performance of two WPTS indicates that massive EBs can be charged with only one HFI, and the cost of the overall system decreases accordingly. [ABSTRACT FROM PUBLISHER]

Generally, single-stage buck–boost inverters consist of distinct circuits operating individually in buck/boost or positive/negative modes, the latter definitely leading to crossover distortion in the output current. This paper proposes a switching strategy that changes the bimodal operation of a single-stage buck–boost topology to a single-mode inverter. This is due to the consequent voltage gain that ensures that the output voltage polarity, apart from its magnitude, is an exclusive function of the duty ratio. Operational principle and salient hardware design are explained with the help of equivalent circuits. Details about the dynamic model are presented, based on which controller design is carried out for both stand-alone and grid-connected operation. Experimental results obtained from a 300-W, 110-V laboratory prototype are presented to validate the performance of the proposed switching strategy. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase multilevel ac/ac converter with reduced number of power semiconductor devices is proposed. For the simple case of a three-level converter, only three bidirectional switches and two capacitors are required. The proposed converter provides a highly sinusoidal and regulated output voltage with a simple topology. The efficiency is high because in each state of operation only one semiconductor conducts. The converter can be easily extended to any desired levels in the output voltage to even more reduce the output total harmonics distortion. Another advantage of the proposed converter is that by increasing the voltage levels, the stress on the switches will decrease. The proper performance of the proposed converter is confirmed through extensive simulation and experimental tests. [ABSTRACT FROM PUBLISHER]

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a novel structure for fault current limiter (FCL), which not only controls the magnitude of fault current, but also is enable to power management in normal and fault condition of utility. The main capabilities of the proposed structure, which is able to connect both ac and dc systems, are controlling the dc reactor current for fault current magnitude control, and management and control of power flow from ac system to dc system. A boost converter is utilized in the proposed structure, that its output is connected to a dc bus, in order to control the dc reactor current. The proposed FCL, which ensures a high protection level of the system, has no impact on utility voltage and load currents. A boost converter is utilized to provide an almost sinusoidal input current. The simulation and experimental results are presented to clarify the theory and feasibility of the proposed FCL, which manifest simple structure of the circuit and show feasibility of the proposed FCL. [ABSTRACT FROM PUBLISHER]

The paper presents a new bridgeless power factor correction (PFC) topology, using a recently proposed controllable LCL filter, namely active virtual ground to achieve efficient power conversion, and high-frequency common mode voltage (CM) reduction. The proposed PFC circuit consists of high-frequency semiconductors for shaping inductor current and low-frequency semiconductors to form two different LCL structures for different conditions. This reduces grid differential mode current ripple or inductance. Besides, the PFC CM voltage, a main problem of bridgeless PFCs, is significantly reduced, since the capacitor in the LCL filter clamps the voltage between the grid and the converter ground. The performance of the proposed PFC is experimentally verified. The results show that the proposed PFC guarantees sinusoidal input current, low high-frequency common-mode voltage noise, and has a good agreement with the theoretical findings. [ABSTRACT FROM AUTHOR]