Search

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

In this paper, a new soft-switching bridgeless single-phase power factor correction (PFC) converter is presented and analyzed. Employing an auxiliary switch, the input current dead angle that is the main drawback of the existing buck-type PFCs is omitted, and thus, the power factor (PF) is improved, which is the main contribution of the paper. Proposed PFC converter operates under discontinuous conduction mode (DCM) and draws sinusoidal input current from power supply inherently. All switches and diodes are turnedonandoffunder soft switching, which leads to low switching losses and elimination of diode reverse recovery problems. Also, minimum numbers of semiconductor devices are in the power flow path that reduce the conduction losses. A 120-W laboratory prototype is implemented and experimental results verify the validity of theoretical analysis and show efficiency of 92.1%. In addition, total harmonic distortion (THD) of 3.3% is achieved and the input current harmonics complies with IEC61000-3-2 Class D requirements. [ABSTRACT FROM AUTHOR]

A high step-up dc–dc converter is proposed in this paper. The presented converter benefits from some advantages such as high voltage gain and continuous input current, which makes it suitable for the renewable energy applications. The presented converter is based on the SEPIC converter. However, the converter voltage gain is improved by employing a coupled inductor and two voltage multipliers. A passive clamp circuit is also added to the proposed converter that increases the voltage gain and reduces the voltage stress on the main switch. Thus, a switch with low $R_{{\text{DS(on)}}}$ will be needed that decreases the conduction loss. Besides, the voltage stress on the output diode in the proposed converter is reduced, which alleviates reverse recovery problem. The steady-state analysis of the proposed converter is discussed in this paper. The analysis is verified with experimental results under the output power of 245 W. [ABSTRACT FROM AUTHOR]

This paper presents the design and construction of a sample of Marx pulsed generator based on boost converter (BC) pulse-forming networks (BCPFNs). BCPFN is used instead of the conventional Marx floors for constructing this pulsed generator. BCPFN is carried out by connecting inductors and capacitors in series and parallel modes, respectively, by using solid-state switches, and during this procedure the pulsed generator converts to BC temporarily and increases the voltage of capacitors uniformly to a considerable value. This technique causes an increase in the discharging voltage level to the load that is many times more than its dc voltage source by charging the capacitors to a greater level. In order to take advantage of the benefits of Marx generator and PFN, this paper suggests a new circuit with the minimum number of switches. It means, to compose BCPFN and Marx, we have tried to design the circuit with fewer switches and instead of it we have achieved our desired performance with changing the operating mode in the states of BC, PFN, BCPFN, and BCPFN Marx. The results are simulated with MATLAB software. At the end, the experimental results of the construction of the above-mentioned system at low-power levels are presented, and the topology’s accuracy is proved by comparing them to the results of simulation. [ABSTRACT FROM AUTHOR]

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a new structure of nonisolated boost dc–dc converters based on voltage-lift technique is proposed. In comparison with conventional nonisolated boost dc–dc converters, the proposed converter generates higher voltage gain. In this paper, the relations between voltage and current of all elements in continuous conduction mode and discontinuous conduction mode are calculated as well as voltage gain in each mode. Then, the critical inductance and stress of switch current are extracted. Finally, the validity of given theories is examined by using the experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a wide-range zero-voltage-switching (ZVS) active-clamped current-fed push–pull converter for fuel cell application. The presented converter achieves ZVS for all of the primary switches and ZCS for secondary diodes from rated load to 10% full load over the wide input voltage variation, improving the overall efficiency. The ZVS of switches is realized by the energy stored in the transformer leakage inductance aided by the secondary parallel inductor. An additional active clamping circuit suppresses the voltage spike as well as assists in realizing ZVS of switches. Low-voltage-rated switches with low on-state resistance can be used. Moreover, the voltage-doubler rectifier is adopted to release the reverse-recovery problem of rectifier diodes and reduce turns ratio of the high-frequency transformer. Detailed steady-state operation, analysis, design, control, comparative study, and experimental results are discussed in depth in this paper. Finally, a 200-W prototype has been built in the laboratory to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Conventional single-phase power-factor-correction (PFC) rectifiers with active power decoupling capability typically require more than three active switches in their circuits. By exploring the concept of power-buffer cell, a new single-stage PFC rectifier with two active switches, one inductor and one small power-buffering capacitor is reported in this paper. The proposed converter can achieve high-power factor, wide output voltage range, and power decoupling function without using electrolytic capacitor. Additionally, an automatic power decoupling control scheme that is simple and easy to implement is proposed in this paper. The operating principle, control method, and design considerations of the proposed rectifier are also provided. A 100-W prototype with ac input voltage of 110 Vrms and a regulated dc output voltage ranging from 30 to 100 V has been successfully designed and practically tested. The experimental results show that with only a 15 μF power-buffering film capacitor, the proposed converter can achieve an input power factor of over 0.98, peak efficiency of 93.9%, and output voltage ripple of less than 3%, at 100-W output power. [ABSTRACT FROM PUBLISHER]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

In this paper, an electric vehicle (EV) battery charger with interleaved Landsman converter (ILC) followed by a flyback converter, is designed and evaluated for improved power quality (PQ) charging of battery. A built-in wave-shaping is obtained at the charger front-end due to improved PQ characteristics of ILC. This PFC converter consists of two Landsman converter cells, which are designed in discontinuous conduction mode (DCM) to share the input and output currents. The current sharing at input results into lower input current ripple as well as peak current stress through the switch, is reduced. This, further improves the input current harmonics profile. Moreover, the reduced output voltage ripple gives reduced rms current in the output capacitor. A phase shift PWM scheme (PSPWM) is used for ILC and the duty cycle for the switches is selected below 50%. This allows the ripple cancellation at line and load sides. The interleaving at PFC stage as well as DCM based design ensures a low cost charging solution as compared to the conventional Landsman converter (CLC) based chargers in this power range. However, the flyback converter provides the current control during the charging of the battery in constant current (CC) and constant voltage (CV) regions. The harmonics spectrum of mains current follows the recommended PQ regulations over a range of varying line voltages and loadings. [ABSTRACT FROM AUTHOR]

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

Load-independent output characteristics of inductive power transfer (IPT) systems are increasingly popular in battery charging. This paper proposes a novel variable-parameter T-circuit (VT) for an IPT system charging a battery with constant current (CC) or constant voltage (CV) output. The VT can transfer a CC/CV input to a CC or CV output by using an ac switch and a passive component (inductor or capacitor). An IPT system with a VT for CC–CV charging can reduce the number of passive components and ac switches. Besides, the proposed VT merits more design freedom of charge current/voltage with the constraints imposed by the loosely coupled transformer parameters compared to that of the traditional one. In addition, there are three kinds of VTs for various IPT charging systems with different requirements. A 400 W laboratory-scale prototype with a 150 mm air gap was built to verify the theoretical analyses. Both electronic load and lead-acid battery are utilized to verify the charging profile of the proposed method. The experimental results of the IPT system indicate that the fluctuation of the charging current in CC mode is less than 2%, and the change rate of charging voltage in CV mode is within 2.9%. The maximum overall efficiency 93.93% of the charging system is achieved from a dc 110 V input to a dc 100 V output. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

The three-level full-bridge (TLFB) dc−dc converter has been widely used in high-voltage, high-power applications. In the experimental test, the neutral-point voltage deviation appears; moreover, it has also been found out that if the flying capacitors are introduced, the input capacitor voltages could realize self-balance even if no active balancing solutions are adopted. In the previous publications, the role of flying capacitors is generally considered to extend the range of soft switching; however, the self-balance ability has not been mentioned or investigated in any publications thus far. In order to fill this gap, this paper provides the detailed mode operation analysis of the TLFB converter and reveals the cause of the imbalance. In addition, the mechanism of the self-balance ability provided by the flying capacitors is explained in detail, which gives a deep insight into the converter. At last, the influence factor of the voltage error in steady state has been analyzed, and the specific expression of the voltage error is also derived. The feasibility of the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

Because it possesses higher current turn-off capability, the inverse current commutation with semiconductor devices (ICCOS) is a better option for the opening switch of an inductive pulsed power supply than the integrated gate commutated thyristor. This paper investigates the counter-current capacitor, which is the key component that determines the turn-off result and the volume of the counter-current branch. The major contributions of this paper include the following: 1) deriving an analytical expression for the minimum precharged capacitor voltage that can reliably turn off the main switch; 2) verifying this expression through a series of experiments within a current range of 0 to 4000 A and an energy range of 0 to 50 kJ; 3) giving an approximate expression for the optimal capacitance that minimizes the precharged energy; and 4) investigating the variation trends of the optimal capacitance and the corresponding optimal precharged energy with varying inductor current. [ABSTRACT FROM PUBLISHER]

In this paper, the Z-source converter is introduced to power factor correction (PFC) applications. The concept is demonstrated through a wireless power transfer (WPT) system for electric vehicle battery charging, namely Z-source resonant converter (ZSRC). Due to the Z-source network (ZSN), the ZSRC inherently performs PFC and regulate the system output voltage simultaneously, without adding extra semiconductor devices and control circuitry to the conventional WPT system such as conventional PFC converters do. In other words, the ZSN can be categorized as a family of the single-stage PFC converters. In addition, the ZSN is suitable for high-power applications since it is immune to shoot-through states, which increases reliability and adds a boost feature to the system. The ZSRC-based WPT system operating principle is described and analyzed in this paper. Simulations and experimental results based on a 1-kW prototype with 20-cm air gap between the system primary and secondary sides are presented to validate the analysis and demonstrate the effectiveness of the ZSN in the PFC of the WPT system. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated bidirectional dc–dc converter is presented. The proposed converter consists of two boost converters to enhance the voltage gain. Four power switches with their body diodes are employed in the proposed converter. Also, two inductors and a capacitor are used as passive components. The input current is divided to the inductors which causes the efficiency to be high. The voltage gain of the proposed converter is higher than the conventional cascaded bidirectional buck/boost converter (CCBC) in step-up mode. Besides, the voltage gain in step-down mode is lower than CCBC. Besides, the efficiency of the proposed converter more than CCBC while the total stress on active switches are same. The simple structure of the proposed converter causes its control to be easy. The steady-state analysis of the proposed converter is discussed in this paper thoroughly. The stress on converters’ devices and the efficiency of the proposed converter and CCBC are compared in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

Many research works have been conducted on increasing the efficiency of interleaved boost converters (IBCs) applied for power factor correction (PFC) by using high-performance power electronic devices and soft switching circuits, which are not helpful in reducing the hardware cost and systematic complexity. In this paper, three intrinsic parameters affecting the efficiency of IBC PFC are found and analyzed, including the switching frequency value, boost inductor value, and output voltage value. Based on the findings, considering the limitations of current ripples, power factor, maximum magnetic flux density, and volume of a boost inductor, an optimization design method for high-efficiency IBC PFC is proposed. A 3.3-kW IBC PFC prototype is developed based on Si devices. The experimental result verifies that the proposed method can improve the efficiency of IBC PFC with low-cost low-performance devices in the full-load range. [ABSTRACT FROM AUTHOR]

In this paper, an input-series flyback converter with the coupled-inductor-based passive snubber is proposed, where the input-series converter is based on transformer integration, and the passive snubber is composed of inductors, capacitors, and diodes. The inductors of the snubber in various series modules are made on a common magnetic core, and the coupled-inductor scheme is adopted. With the help of the coupled inductor, active input voltage sharing of the input-series converter can also be achieved after the switches are turned off, and voltage sharing of the switch in each series module can be ensured, which overcome the shortcomings of the existing input-series flyback converter. Active voltage sharing processes caused by the coupled inductor are analyzed in detail. Furthermore, the design guideline of the passive snubber is discussed. Finally, the experimental study has been done on a 1500 Vdc/60 W laboratory-made prototype composed of three flyback series modules, and the feasibility of the proposed method and the theoretical analysis is verified by the experimental results. [ABSTRACT FROM AUTHOR]

In this paper, an expandable single-input three-output high step-up dc–dc boost converter is proposed. The voltage conversion ratio of the output ports of the converter can be increased by inductor-diode-capacitor and diode-capacitor cells. The proposed converter can be applied in renewable energy conversion systems, such as in photovoltaic and fuel cells. Also, due to the three output ports of the converter, it can be utilized in portable devices which require high voltage conversions. The main advantage of the proposed converter is supplying loads with different voltages and current ranges due to the expandable structure of the converter. Besides, the proposed converter has the merit of achieving high voltage gains at high frequencies without preselecting wide duty cycles. Furthermore, the proposed converter is able to achieve higher voltage ranges without having any transformer or coupled inductors in its structure; consequently, the related drawbacks are avoided. The switching pattern of the converter is simple and both switches are on and off simultaneously. In this study, a single switching period of the proposed converter, the voltage conversion ratios of the output ports and the expanded form of the structure are analyzed theoretically. Finally, to verify the theoretical results, the experimental results for 40-V input/200-V, 100-V and 360-V outputs with total 600-W output power are extracted and compared with each other. [ABSTRACT FROM AUTHOR]

Impedance-source inverters using coupled inductors have been investigated as alternatives for providing high step-up voltages. However, leakage inductances of the coupled inductors have commonly led to lower overall effectiveness, in addition to generating high dc-link voltage spikes. The latter raises voltage stresses of switches, which in turn, may reduce the power levels of the inverters. A high step-up Y-source inverter has therefore been proposed in this paper to provide a high boost with a smooth dc-link voltage ensured by proper recycling of the leakage energy. These features have been verified by comparing simulation and experimental results of an existing Y-source and the proposed inverters. Factors compared are their respective boost ratios, voltage stresses, current stresses, and dc-link voltage spikes. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

A switching-capacitor-based buck–boost converter (with common ground) for point of load applications is proposed in this paper. It is capable of operating in stand-alone buck or boost mode in addition to its primary operation of performing the buck–boost conversion. The striking feature of the proposed converter is low source current ripple content irrespective of its mode of operation (buck–boost, buck, or boost). First, feasible pulsewidth modulation schemes for the proposed converter are identified and thereafter the corresponding circuit performance analysis, steady-state analysis, and state-space modelling is established. Through steady-state analysis, voltage gain expressions are formulated and equations defining L-C components are derived in terms of their ripple quantities. The state-space models are used to formulate small-signal analysis and to obtain the relevant transfer functions required in the controller design. A voltage-mode/current-mode controller is designed, with a tradeoff in bandwidth, to control the proposed converter and transit it from buck to boost mode or vice versa seamlessly. A 30–55 W, 100 kHz, prototype point of load converter with 36-V input dc source is built to supply power at constant load voltage of either 48 or 28 V. The proposed converters’ effectiveness is demonstrated experimentally in terms of reduced source current ripple along with seamless transition from buck to boost mode and vice versa. [ABSTRACT FROM AUTHOR]

In recent years, modular multilevel converter (MMC) is considered for medium-voltage variable speed drives (VSD) due to its modularity and higher reliability. However, the major drawback of the MMC-based VSD is the higher capacitor ripple voltage at lower operating speeds. In literature, this ripple voltage is reduced by injecting a high-frequency circulating current into each arm. This additional circulating current increases the overall current rating of the devices, inductors, and capacitors. Alternatively, the capacitor ripple voltage can be reduced at the lower output frequency by reducing the dc-bus voltage. This paper proposes a new configuration using a multipulse diode-bridge rectifier to reduce the dc-bus voltage when the drive is operated at lower speeds. Therefore, the capacitor ripple voltage decreases without injecting any circulating current. In addition, a new technique is proposed to maintain the peak-to-peak value of the submodule capacitor ripple voltage constant at near-zero speed. The proposed converter with 24-pulse rectifier configuration is simulated in MATLAB/Simulink, and the experimental validation is carried out on a prototype with 12-pulse rectifier. [ABSTRACT FROM AUTHOR]

This paper presents an architecture for differential Colpitts voltage-controlled oscillators (VCOs) in complementary metal–oxide–semiconductor (CMOS) that utilizes three design techniques to extend the tuning range (TR) of the VCO, while maintaining a low phase noise (PN) and a low power consumption. First, a switched-capacitor bank based on a variable capacitive feedback technique is introduced to achieve a wide TR with a minimal PN degradation. Second, a $G_{m}$ -boosting technique using interstage inductors is employed to lower the power consumption and relax VCO startup issues. Third, a dynamic forward-body self-biased technique is used to further reduce the power consumption and PN of the proposed structure. As a proof of concept, a 26.3-GHz differential Colpitts VCO is designed and fabricated in a 65-nm CMOS process. Based on the measurement results, the VCO achieves a PN of −122.1 dBc/Hz at 10-MHz offset from the center frequency, and a TR of 20%. The circuit consumes 2.3 mW from a 1-V supply and excluding the pads occupies a 0.22 mm2 of silicon area. Compared to the recently published CMOS VCOs within the same frequency range, the proposed VCO simultaneously achieves a wide TR, low power dissipation, and low PN, resulting in a figure of merit (FOM) and FOM incorporating the TR (FOM $_{T}$) of −187 and −193 dBc/Hz at 10-MHz offset from the center frequency, respectively. [ABSTRACT FROM AUTHOR]

The ultra-high voltage gain dc–dc converters are extremely required because of the low voltage level of many nonpolluting power resources. This paper proposes an ultra-high voltage gain converter based on an interleave technique and using three-winding coupled inductor and voltage multiplier cell. The interleave technique is useful for reducing the size of the filter components. In the proposed converter, high voltage gain is achieved without extreme duty cycle of solid-state switches. The voltage stress across the semiconductor devices can be reduced by increasing the turn ratio of the secondary of the coupled inductors. In addition, because of the implementation of the interleave structure, peak-to-peak variation of the main input current and switching losses are substantially reduced. The steady-state principles of the proposed converter in continuous conduction mode operation are given. Also, design equations are presented. Validity and performance of the proposed converter are surveyed by simulation and experimental results of a 120 W prototype. [ABSTRACT FROM AUTHOR]

A simple buck–boost LED driver suitable for battery operated applications with limited input voltage level is presented in this paper. Soft switching performance is provided for the main switch via a resonant circuit to improve the converter efficiency. The incorporated auxiliary switch also performs under zero voltage switching condition. Both power switches can be driven with a simple gate drive circuit, so, the additional switch does not add any driving complexity. In addition, only one magnetic element is utilized in the proposed LED driver which contributes to circuit simplicity and lower weight and size. Also, all diodes turn off at zero current switching which eliminates the reverse recovery losses and improves efficiency. A laboratory prototype converting 12 V input voltage to 32 V output operating at 26 W output power is implemented and tested to verify the effectiveness of the proposed LED driver. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

The voltage ratings for dc transmission and distribution are not currently standardized because cable technology is advancing rapidly and therefore a low step-ratio dc–dc converter at multi-megawatt scale is a crucial technology for combining point-to-point dc links into multi-terminal networks. This paper presents a modular multilevel dc–dc converter configuration with only a single stack of half-bridge sub-modules (SM) and a resonant tank. The power processed through the stack is a small fraction of the throughput power if the step ratio is small ($1 - {\boldsymbol{v}_{\boldsymbol{L}}}/{\boldsymbol{v}_{\boldsymbol{H}}}$). Detailed analysis shows the required semiconductor ratings are much smaller compared to the front-to-front MMC and modular converters derived from standard dc–dc topologies. Further, the requirement for SM capacitive energy storage is also significantly less than those converters. The theoretical analysis and the operating principles have been verified by full-scale simulation examples and experiments with a down-scaled prototype. The SMs are operated with an adjustable phase shift to create a high frequency excitation across the resonant tank for further volume reduction. The SM capacitors self-balance without the need for switching pattern adjustments and the resonant operation provides soft switching for all power switches to increase efficiency. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

High step-down voltage conversion is necessary to bridge the voltage gap between main power converters and low-voltage auxiliary electronics in power conversion systems. Switched capacitor converters (SCCs) are an attractive candidate as a high step-down converter, but their poor voltage regulation capability may limit their applications. Pulsewidth modulation (PWM) SCCs with adjustable high step-down voltage conversion are proposed in this paper. The proposed PWM SCCs can be derived from traditional SCCs by replacing an energy transfer capacitor with a switched-capacitor-inductor (SCL) cell that comprises inductors, capacitors, and diodes to realize PWM-controllable voltage conversion. The voltage step-down ratio of the proposed PWM SCCs is not only PWM controllable but also adjustable with structures of SCCs and SCL cells. Two representative PWM SCCs were taken as examples to perform the operational analysis. The prototypes of both representative PWM SCCs were built and tested to demonstrate the proposed concept. [ABSTRACT FROM AUTHOR]

This paper proposes a Class-DEMtuned power amplifier. The proposed amplifier achieves zero-voltage switching (ZVS), zero-voltage derivative switching (ZVDS), and zero-current switching (ZCS) at turning-on, and ZVS, ZVDS, ZCS, and zero-current derivative switching at turning-off. Therefore, the switching losses are extremely low, which is suitable for high-frequency operation. Moreover, the switch voltage stress is low, which is no more than its input voltage. A proposed amplifier was designed, built, and tested. The measured power conversion efficiency was 93.2% under the condition of the main input voltage of 46.8 V, the operating frequency of 1 MHz, and the output power of 4.87 W. [ABSTRACT FROM AUTHOR]

The three-phase four-wire inverter with split dc-link capacitors can supply unbalanced loads. For the purpose of reducing the filter inductors, a neutral inductor could be introduced into the neutral line. This paper analyzes the operation principle of the three-phase four-wire inverter with split dc-link capacitors when a neutral inductor is introduced. It is illustrated that the neutral inductor can reduce the zero-sequence switching harmonics in the voltages between the phase-leg midpoints and the output neutral point, thus the filter inductors can be reduced. The optimized design of the neutral inductor and filter inductors is proposed with the considerations of the inductor current ripple, the ability of supplying unbalanced loads, and the total energy stored in the inductors. The equivalent circuits of the three-phase four-wire inverter with split dc-link capacitors and neutral inductor is derived in the α–β–0 frame, and the zero-axis voltage regulator is modified to suppress the third-order harmonic in the zero-sequence current caused by the deadtime of the drive signals for the power switches. Finally, the experimental results from a 9-kW prototype are provided to prove the effectiveness of the proposed optimized design of the neutral inductor and filter inductors and the control strategy of the inverter. [ABSTRACT FROM AUTHOR]

In this paper, a family of step-up resonant switched-capacitor converters (RSCs) with a continuously adjustable conversion ratio is proposed based on the Cuk dual-resonance core (DRC) featuring two resonant paths. By adopting the on-time fixed frequency modulation, the two resonant paths can conduct simultaneously and satisfy the charge balance of the flying capacitor during the overlapping period. As a result, the conversion ratio—upper bounded by two determined by the circuit configuration—can vary continuously and efficiently even at the light load condition (1/10 of the rated power). A comprehensive analysis—the operation principle, voltage-gain curve, and voltage/current stresses—about the DRC is given. In addition, the Cuk DRC was extended to the series–parallel switched-capacitor converter (SCC), Fibonacci SCC, and voltage doubler to form a family of step-up RSCs, whose voltage-gain curves of different topologies are derived. Moreover, a characteristic comparison between the Cuk DRC and the traditional “direct” and “indirect” resonant core is given. Then, a 48 to 62–94.6 V resonant core with peak efficiency 97.8% and maximum power 120 W under the open loop condition was built. The analyses were verified by both experimental and simulation results. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents an overview of resonant and hybrid switched-capacitor converters with a particular focus on multimode operation. The multimode approach is discussed as a tool to affect high efficiency and power density across a wide load range, provide variable regulation, and, as a general framework, to conceptualize the advantages and opportunities of the approach compared to more traditional dc–dc converters. A general analysis is provided to quantify the advantage of hybrid and resonant converters that factors in the tradeoffs between size and loss in the magnetic component and voltage stress on the active devices. A broader set of operating modes is presented that spans continuous and discontinuous conduction and includes resonant, quasi-resonant, and more traditional buck- or boost-like operation. A prototype flying-capacitor multilevel converter is presented to demonstrate the variety of operating modes and motivate important considerations such as voltage balance on the flying capacitors. [ABSTRACT FROM AUTHOR]

In this paper, a novel buck–boost dc–dc converter with continuous input current is proposed. The voltage gain of the presented converter is higher than conventional converters, such as buck–boost, single-ended primary-inductance converter, Cuk, and Zeta converters. This converter works only by one switch and voltage stress across the switch is low. Input current of the proposed converter is continuous so a large filter at the input is not needed. Furthermore, continuous input current has made this converter suitable for renewable energy and fuel cell applications. In this converter, noninverting output voltage is obtained and high gain of voltage is achieved as well. So it can operate at wide output voltage range only by changing the duty cycle of the power switch pulse. The presented converter can easily controlled in continuous conduction mode operation, because of using only one power switch. In the following, the principle of operation and the mathematical analyses of the proposed converter are explained, finally, validity of the proposed dc–dc converter is verified by the experimental results. [ABSTRACT FROM AUTHOR]

High-frequency (HF) switching and ac-side unbalanced loads challenge smart transformer (ST)-fed hybrid grids (both ac and dc), causing common-mode (CM) voltage variations and dc-link oscillation. The HF switching introduces an HF CM voltage and the ac grid unbalanced loads introduce a fundamental frequency CM voltage in hybrid grids. The CM voltage in ST-fed distributed grids degrades the power quality, threatens the safety of the connected devices, and potentially constitutes a health risk for the operators of such devices. Therefore, this paper systematically analyzes the root causes of the ST CM voltage variations and the impacts on hybrid grids. Based on the two typical configurations (three- and four-leg converters), the performance and requirements of CM inductor filter and bypass CM filter on HF CM voltage suppression are studied in detail. By considering the CM voltage suppression and dc capacitor lifetime, a four-leg converter with improved modulation strategy and small dc bypass film capacitor is proposed. The simulation and experimental results clearly verify the feasibility and correctness of the proposed strategies. [ABSTRACT FROM AUTHOR]