Search

This paper presents an improved H8 power converter for common-mode voltage (CMV) reduction and electromagnetic interference suppression. The proposed H8 converter can realize zero CMV variation when entering and leaving the zero state, which is mainly achieved by both the improvement of the structure and the control strategy. For the system structure, two switches are added on the dc bus to float the ac part of the three-phase converter in the zero state. Besides, additional capacitors are used to realize controllable CMV. For the control strategy, a simple control strategy is proposed for the H8 converter. It can automatically adapt to the flowing orientation of the load current to realize synchronous switching of the power switches, which effectively eliminates the impact of the dead time. Through analysis, simulations, and experiment, a comparison between the proposed H8 converter and the conventional H6 converter is performed. Results validate the effectiveness of the H8 topology. [ABSTRACT FROM AUTHOR]

Active pulsating power buffering (PPB) function can effectively reduce the twice-line frequency energy storage requirement in a single-phase rectifier. Existing single-phase solutions with active PPB must utilize more than two active switches in their circuits. Compared with conventional single-active-switch solutions without active PPB (e.g., a boost power-factor-correction (PFC) rectifier), the cost of additional semiconductor switches and gate drive circuitry in an active PPB-based rectifier may not be justified for low-power applications. This paper presents a family of single-switch single-phase rectifier with active PPB. Taking advantage of the on-time and off-time of a single switch, the proposed rectifiers are formulated by merging two converters that are duty and frequency controlled. The steady-state characteristics of these converters are analyzed. A step-by-step design procedure is provided, and an active control method for limiting the maximum switching frequency for wide-load-range operation is presented. A 100-W prototype is built for the demonstration of the proposed single-switch rectifier concept. It is envisaged that this concept, when combined with other circuit formulation techniques, e.g., partial power processing, dc-voltage feedback, may lead to new derivatives of single-switch rectifiers with more advanced features. [ABSTRACT FROM AUTHOR]

This paper presents a new class of switched tank converters (abbreviated as STCs) for high-efficiency high-density nonisolated dc–dc applications where large voltage step down (up) ratios are required. Distinguished from switched capacitor converters, the STCs uniquely employ LC resonant tanks to partially replace the flying capacitors for energy transfer. Full soft charging, soft switching, and minimal device voltage stresses are achieved under all operating conditions. The STCs feature very high efficiency, power density, and robustness against component nonidealities over a wide range of operating conditions. Furthermore, thanks to the full resonant operation, multiple STCs can operate in parallel with inherent droop current sharing, offering the best scalability and control simplicity. These attributes make STC a disruptive and robust technology viable for industry's high volume adoption. A novel equivalent DCX building block principle is introduced to simplify the analysis of STC. A 98.9% efficiency STC product evaluation board (4-to-1, 650 W) has been developed and demonstrated for the next-generation of 48-V bus conversion for data center servers. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

In recent years, significant progress has been made in HVdc transmission, particularly the voltage-source-converter technology using modular multilevel converters. There is increasing demand to develop high-power dc/dc converters to interconnect HVdc systems with different voltage levels. In this paper, a novel hybrid dc/dc converter topology is proposed by the combination of a new three-switch submodule (SM) circuit and series-connected thyristors and diodes. This topology presents less amount of semiconductors, very attractive capital costs, small footprint, and low power losses. Operating principles of this new three-switch SM and the dc/dc converter are explained, while the modulation and control schemes are also developed. The validity of the proposed topology is verified by simulation results based on a 150 MW, 200 kV/300 kV dc/dc converter. Efficiency estimates indicate that this topology could have power losses as low as 0.3% rated power. A scaled-down prototype has also been built and tested to confirm its effectiveness. [ABSTRACT FROM AUTHOR]

In this paper, a modular topology is presented for generating high-voltage pulsed power. The proposed structure consists of Marx-type modules, which are based on the switched-capacitor (SC) concept. This module receives an input voltage and, depending on the requirement of the user, produces an output voltage either equal to the input or twice as much as the input voltage, which shows the flexibility of our model. The capability of the module to produce a doubled output makes it appropriate for applications with low input voltage sources. Also, the topology has the capability of generating combined wide and narrow pulses. The topology was simulated in MATLAB Simulink and a laboratory setup was built to test its operation. The results validate the theoretical basis of the structure. [ABSTRACT FROM AUTHOR]

In this paper, a highly reliable back-to-back (BTB) power converter is proposed for doubly fed induction generator-based wind turbines (DFIG-WTs). When a power switch open-circuit fault is encountered in either the grid-side converter (GSC) or the rotor-side converter (RSC), a four-switch three-phase (FSTP) topology is formed to avoid using redundant bridge arms, which reduces the power circuit complexity and minimizes the conduction and switching losses. A simplified space vector pulsewidth modulation technique is used to eliminate sector identification and complex trigonometric calculations. In addition, the influence of dc-bus capacitor voltage unbalance on the electromagnetic torque is analyzed in detail. The offset current components are calculated, and they are deducted from the reference values in the modified control strategies to suppress the dc-bus voltage deviation. Moreover, the power loss model of a BTB converter is analyzed in detail, and the efficiency study is performed in various post-fault situations. Simulations in MATLAB/Simulink are carried out to verify the performance of a DFIG-WT based on a FSTP BTB converter. Furthermore, the control hardware-in-the-loop setup with RSC and GSC separately simulated in a digital real-time simulator is applied for experimental verification of the proposed control strategy. [ABSTRACT FROM AUTHOR]

A switching-capacitor-based buck–boost converter (with common ground) for point of load applications is proposed in this paper. It is capable of operating in stand-alone buck or boost mode in addition to its primary operation of performing the buck–boost conversion. The striking feature of the proposed converter is low source current ripple content irrespective of its mode of operation (buck–boost, buck, or boost). First, feasible pulsewidth modulation schemes for the proposed converter are identified and thereafter the corresponding circuit performance analysis, steady-state analysis, and state-space modelling is established. Through steady-state analysis, voltage gain expressions are formulated and equations defining L-C components are derived in terms of their ripple quantities. The state-space models are used to formulate small-signal analysis and to obtain the relevant transfer functions required in the controller design. A voltage-mode/current-mode controller is designed, with a tradeoff in bandwidth, to control the proposed converter and transit it from buck to boost mode or vice versa seamlessly. A 30–55 W, 100 kHz, prototype point of load converter with 36-V input dc source is built to supply power at constant load voltage of either 48 or 28 V. The proposed converters’ effectiveness is demonstrated experimentally in terms of reduced source current ripple along with seamless transition from buck to boost mode and vice versa. [ABSTRACT FROM AUTHOR]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

Switched-capacitor converter (SCC) featuring high efficiency and power density has attracted industry interest, but weak output voltage regulation hinders its application. This paper presents an optimized phase-shift (PS) control strategy for a bridge modular SCC, utilized in energy storage system, to obtain continuous conversion ratio and high-efficiency operation. By employing a small inductor as current buffer, the control strategy could be implemented to regulate output voltage conveniently with excellent steady and dynamic performance in step-down mode as well as step-up mode. Most importantly, the high-efficiency operation mechanism never reported before is revealed here. Correspondingly, the active circumfluence could be controlled through optimizing the range of PS time, which will avoid the loss in circuit self. Meanwhile, the soft-switching conditions of all the switches are comprehensively analyzed and soft-switching operations are achieved according to the logic timing control of the power devices, improving efficiency further. Finally, the prototype of the proposed converter was built and the experimental results validated the principle and features of the conversion method. [ABSTRACT FROM AUTHOR]

This paper presents a modular multilevel series/parallel converter (MMSPC) with intermodule switched-inductor power transfer. The switched-inductor voltage conversion feature allows controllable and efficient transfer of energy between modules with nonnegligible voltage difference, providing both step-down and step-up functionalities. Thus, this converter can accurately control and rapidly adjust the voltage of each module to generate an ac output voltage waveform with a controllable number of levels, increasing the quality of the output. Moreover, the intrinsic dc–dc conversion feature can generate a dc controllable output voltage and enable new applications. In this text, we specifically demonstrate how the flexibility of obtaining both ac and dc output with the same setup renders the topology promising for battery energy storage systems and dc microgrid applications. Experimental results validate the topology and concept of an MMSPC with intrinsic switched-inductor conversion. [ABSTRACT FROM AUTHOR]

This paper proposes a family of multiport switched-capacitor multilevel inverter (SCMLI) topologies for high-frequency ac power distribution. It employs asymmetric dc voltage sources with a common ground that makes it ideal to be employed in renewable energy farms and modern electric vehicles. The proposed family of step-up SCMLI attains higher number of output voltage steps with optimum component count in comparison to several existing topologies. The problem of capacitor voltage balancing is solved as the capacitors are inherently charged to a finite voltage every half cycle. In-depth study on two staircase modulation strategies, namely, selective harmonic elimination and minimum total harmonic distortion (THD) scheme is presented with study on the variation of switching angles and THD with modulation indices under both schemes. Working principle and analysis are presented for the proposed family of topologies. Simulation outcomes are validated with experimental results under both the aforementioned modulation schemes with equal and unequal output voltage waveform steps. [ABSTRACT FROM AUTHOR]

This paper presents new space vector pulsewidth modulation (PWM) strategies for a single-phase three-level buck-boost neutral point clamped inverter coupled with impedance-source (IS) network. These strategies can be implemented for systems with any IS network with neutral point. The case study system is based on the quasi-Z-source inverter with continuous input current. To demonstrate an improved performance, the strategies are compared with a traditional PWM strategy. The advantages lie in reduced switching number, without output voltage quality distortion. The simulation and experimental results confirm the theoretical predictions. [ABSTRACT FROM AUTHOR]

This paper explores the use of the flying-capacitor multilevel (FCML) topology in high step-up conversion. Compared to the conventional two-level boost converter, the FCML topology utilizes high energy density capacitors to facilitate inductors with storing and transferring energy during the conversion process, which brings features, such as lower voltage stress on the switches, reduced voltage stress on the inductor, and high effective switching frequency at the switching node. As a result, the total volume of the passive components in the converter is greatly reduced while maintaining high efficiency at high voltage gain. To demonstrate the potential high power density and high efficiency, a hardware prototype that converts 100 V to 1 kV with 820-W maximum output power is built. Such specifications require careful optimizations in many aspects of the converter to ensure a high power density and efficiency design. The implemented solutions and associate design process are presented in detail, with comparison with other state-of-the-art solutions. The hardware prototype has successfully demonstrated a peak efficiency of 94.1%, and 329 W/in $^3$ (20 W/cm $^3$) overall power density. [ABSTRACT FROM AUTHOR]

This paper presents three nonisolated high voltage gain dc–dc converters with ripple-free input current. The proposed converters combine coupled inductors and voltage-doubler structure (VDS) to achieve high step-up of input voltage. An active clamp circuit is used to suppress voltage spike of the switch caused by of the leakage inductor of the coupled inductor. VDS is placed in the secondary winding of the coupled inductor that clamps the diodes voltage stress. Working principle and design methodology of the proposed converters are presented in detail. Experimental results for a 300 W laboratory prototype, 48 V input voltage, and regulated output voltage of 400 V, are shown to validate the operation of proposed converters. [ABSTRACT FROM AUTHOR]

This paper proposes an enhanced hybrid modular multilevel converter (MMC), which utilizes a combination of half-bridge submodules (HBSM) and at least one full-bridge submodule (FBSM). In the proposed structure, FBSMs work with half of the HBSMs nominal voltage in each arm. Due to the presence of FBSMs, HBSMs switching frequency drops significantly, which reduces the converter power loss compared to half-bridge based MMCs. Furthermore, because of redundant FBSMs, (2N + 1)-modulation can be employed to generate the output voltage without increasing the circulating current, thus, the converter performance is improved notably. Besides, with the redundant FBSMs, the converter can continue its operation even if a fault occurs in one of HBSM switches. All the control procedure is accomplished using model predictive control strategy and performance of the proposed converter is verified by several simulation and experimental studies. The obtained results confirm the feasibility of the proposed scheme in reducing the converter loss, improving its performance and fault-tolerant operation. [ABSTRACT FROM AUTHOR]

LEDs have finally emerged as the dominant lighting technology. As such, the lighting industry values power converters that have high efficiency, unity power factor, minimal flicker, dimming, low cost, and a small form factor. This paper presents an integrated circuit (IC) LED driver that is designed to achieve these goals. It introduces multilevel converters with sigma–delta modulation to the power IC space. The driver features a pair of sigma–delta-controlled multilevel converters. The first is a multilevel rectifier responsible for power factor correction and dimming. The second is a bidirectional multilevel inverter used to cancel ac power ripple from the dc bus. The system also contains an output stage that powers the LEDs with dc and provides for galvanic isolation. The IC LED driver has been simulated and prototyped on a silicon fabrication process. Its functional performance indicates that integrated multilevel converters are a viable topology for lighting or other similar applications. [ABSTRACT FROM AUTHOR]

This paper presents a novel step-up dc to ac converter with only one power supply. These types of converters are suitable for renewable and sustainable energy applications with low input dc sources. The proposed topology has the ability of self-voltage balancing and does not apply end side H-bridge to produce a bipolar staircase waveform. Consequently, switching losses and voltage stress of semiconductor components are reduced to a great extent. A small dc voltage source can be used to achieve a high voltage high quality ac waveform through switching the precharged capacitors in series and in parallel. Circuit configuration and its operation principle, capacitors’ charging process, thermal model, capacitances, and losses calculations are discussed in details. Moreover, the comparison of the proposed circuit with the other single source multilevel converters shows that the proposed topology reduces the number of circuit elements. Finally, a laboratory nine-level prototype is built to verify the theoretical analyses and feasibility of the proposed topology. The experimental results show that the converter efficiency at 1 KW output power is 92.75%. [ABSTRACT FROM AUTHOR]

Discontinuous modulation applied to modular multilevel converters is an effective method for reducing the capacitor voltage ripples. In this paper, the discontinuous modulation is adapted and used in a motor drive application. For proper operation of the converter, a new energy controller is presented, which is suitable for operation with nonsinusoidal reference signals. Experimental results comparing the discontinuous modulation with other techniques operating at low motor speeds are shown. The results demonstrate the effectiveness of the discontinuous modulation on reducing capacitor voltage ripples and power losses. [ABSTRACT FROM AUTHOR]

This paper presents a modified modular multilevel converter with the three-terminal middle-cells inserted between arms and ac-side for medium voltage applications. It is intended to reduce the submodule capacitor voltage ripples by controlling the high-frequency powers flowing among arm branches for low-frequency output operations without common-mode voltage injected in ac-side. Due to the physical connection among the upper arm, the lower arm and ac-side, the middle-cell can be regarded as the excess degree of freedom to modify the dc-side and ac-side characteristics. Therefore, the common-mode voltage in ac-side can be eliminated by the inverse common-mode voltage produced by the middle-cell in ac-side. Moreover, owing to the unique structure of the middle-cell, the middle-cell capacitor voltage also results in a small ripple due to the high-frequency current flowing into it by proper control. The operation principle and control strategy of the middle-cell has been proposed in detail. Simulation and experimental results have verified the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

There is increasing interest in the use of transformer-less systems for grid-connected photovoltaic applications. Compared to transformer-coupled solutions, transformer-less systems offer a typical efficiency increase of 1–2%, reduced system size and weight, and a reduction in cost. However, the removal of the transformer has technical implications. In addition to the loss of galvanic isolation, dc current injection into the grid is a potential risk. While desirable, complete mitigation of dc current injection via convention current control methods is known to be particularly challenging. For this reason, this paper proposes an active dc suppression method, in which the dc current injection is accurately determined by extracting the line-frequency component from inverter dc-link current measurements, and then, mitigated with an active closed-loop controller. Experimental results from a laboratory grid-connected inverter system are presented to demonstrate the high performance of the proposed technique. [ABSTRACT FROM AUTHOR]

A dual-input high step-up DC/DC converter with zero voltage turn-off (ZVT) auxiliary circuit is presented in this paper. The cost of whole photovoltaic (PV) power could be decreased significantly by the proposed converter because it allows two PV panels to be connected at the same time. ZVT auxiliary circuit provides soft switching in a wide range of load variations with six passive components. Turn-off switching losses could be decreased and the efficiency of the whole converter could be improved. In , the operation principle and performance characteristics of the proposed converter have been analyzed and an 800 W experimental prototype has been built to validate the analytical results in. In , a dual-input maximum power point tracking (DMPPT) control algorithm has been designed for the proposed converter. Experimental results show that two PV panels can achieve the maximum power output state separately by the proposed DMPPT control algorithm. [ABSTRACT FROM AUTHOR]

The non-inverting buck-boost converter has emerged as one of the most promising topologies for distributed maximum power point tracking applications. Pressure to reduce cost and volume of photovoltaic module integrated converters often compels bootstrap capacitor type gate drivers. The bootstrap technique is a simple and economical solution to create a floating power supply for high-side gate drivers. However, it comes with a major challenge, as the low-side switch must be periodically turned on, to recharge the high-side bootstrap capacitor. In the buck and the boost mode, one of the switching legs of the converter must be held with the high-side switch on, which eventually discharges the high-side capacitor. When the non-inverting buck-boost input voltage is regulated by means of a single voltage loop, recharging the bootstrap capacitor causes an undesired ripple in the PV module voltage, degrading the regulation quality. In order to mitigate this problem, this paper proposes a cascaded control technique, entailing regulation of the PV module voltage and inductor current. The cascaded controller dramatically improves the rejection of the disturbance induced by the periodic recharge of the bootstrap capacitor, thanks to the fast action of the current loop, regulating the average value of the inductor current. Converter transfer functions and controller design are derived and validated. Experimental results clearly show that the cascaded control scheme outperforms the traditional voltage control scheme, resulting in a better regulation of the PV module voltage. This main advantage comes at the cost of an additional measurement of the average inductor current. [ABSTRACT FROM AUTHOR]

High-brightness light-emitting diode (LED) is next generation of green lighting. However, the bulky electrolytic capacitor is required to compensate the difference of pulsating power, thereby restricting the lifetime. Meanwhile, the existing drivers based on pulse frequency modulation (PFM) is bound to arouse heavy electromagnetic interference. In this paper, the series resonant converter based LED drive is proposed to overcome the shortcomings of electrolytic capacitor and PFM control. The proposed method is to attenuate the low frequency ripples delivered from the power factor correction (PFC) to LEDs; therefore, the capacitance is reduced for energy storage of offline LED drivers. On account of the adoption of the switching controlled capacitor (SCC), the constant frequency control is achieved by the regulations of the equivalent capacitance. Half-bridge switches are shared by the bridgeless PFC and the resonant unit, therefore, single-stage LED drive is realized with high efficiency. In addition, SCC is simultaneously shared for the upper and lower half-bridge to reduce the cost and improve the power density. Operating principle, design considerations, and performance comparisons are examined in detail. Finally, all the superior performances of proposed LED driver are verified by simulation and experimental prototypes with two-channel LEDs, and rated output power of 80 W. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-stage, isolated, and single-phase dc–ac converter topology, suitable for low-medium power-scale solar photovoltaic and fuel-cell applications. The circuit employs two full-bridge cells with floating dc bus capacitors placed on either side of a high-frequency transformer and works on the dual-active-bridge principle. It has advantages of a single-stage power processing structure, low device count (uses eight switches), and the possibility of achieving zero-voltage-switching operation over the full ac line cycle. Moreover, by dynamic variation of phase-shift between the high-frequency primary and secondary voltages, twice-line-frequency energy buffering can be affected via the high-voltage side dc bus capacitor, which reduces decoupling capacitance requirement, enabling a film capacitor-based implementation. Basic operating principle, control strategy, and detailed design optimization guidelines of the circuit are described followed by simulation results to validate the approach. Practical evaluation of converter performance is done on a 250 W, 20–35 V input, and 110 V rms output prototype. [ABSTRACT FROM AUTHOR]

Conventional two-level as well as multilevel voltage-source-inverter topologies with a hexagonal voltage-space vector structure generate low-order harmonics in the machine terminal voltages when operated beyond the linear modulation range in variable speed drive application. Progressing from hexagonal to a higher sided polygonal voltage-space-vector structure (VSVS) suppresses significant low-order harmonics throughout the modulation range. In addition, the linear modulation range will also be enhanced very near to the base speed. In this paper, for the first time, the generation of a multilevel 24-sided VSVS using a single dc source for induction-motor drives is proposed. A cascaded topology with a dc-source-fed flying-capacitor inverter and two low-voltage capacitor-fed H-bridge cells forms the power circuit. The features and advantages of the proposed scheme are validated through experimental results and discussions. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) represent an emerging topology in medium-voltage (MV) and high-voltage applications. But for MV variable-speed motor drives, the MMC faces the challenge of large capacitor voltage ripple at low speeds. Delightfully, a hybrid MMC (HMMC) has proved to be potential in MV motor drives, since this topology has a lower capacitor voltage ripple and does not introduce any common voltage to the motor. This paper proposed a method to decrease the average capacitor voltage of the HMMC, which can effectively drive the motor at very low speeds without significantly increasing the submodule (SM) capacitance. Moreover, the selection of average capacitor voltage and the dimension of the SM capacitance are presented. Simulation and experimental results verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper explores the large-signal and small-signal dynamics of a series-capacitor (SC) buck-type converter and introduces an optimal closed-loop control scheme to accommodate both the steady-state and transient modes. As opposed to a conventional buck converter, where time-optimal control is realized by a single on–off cycle, in the SC-buck topology, there is a need to distribute the switching phases to satisfy the charge balance of the SC. The new control method merges a voltage-mode controller for the steady-state operation and a nonlinear, state-plane based transient-mode controller for load transients. A detailed principle of the operation of the SC-buck converter is provided and explained through an average-behavioral model and state-plane analysis. The operation of the controller is experimentally verified on a 20 W 12 V-to-1 V converter, demonstrating voltage-mode control operation as well as minimum-deviation and time-optimal responses for load transients. [ABSTRACT FROM AUTHOR]

Voltages of series-connected batteries gradually become imbalanced due to nonuniformity in terms of not only battery characteristics but also self-discharge rate that is significantly dependent on temperature. In large-scale energy storage systems, a large temperature gradient is very likely because of its huge geometry, and therefore, equalizers capable of relatively large equalization currents would be necessary to eliminate voltage imbalance originating from uneven temperature distribution. A two-switch string-to-battery voltage equalizer using a half-bridge converter with multistacked current doublers (MSCDs) is proposed for series-connected batteries in this paper. The proposed equalizer is capable of providing relatively large equalization currents without increasing ripple currents thanks to the interleaved operation of the MSCDs. Fundamental operational analysis for a discontinuous conduction mode, in which currents in the equalizer can be limited to desired levels without feedback control, is performed. The experimental results of equalization tests performed for four supercapacitor modules and lithium-ion batteries connected in series demonstrated the equalization performance of the proposed equalizer. [ABSTRACT FROM AUTHOR]

Cascaded multilevel inverter (CMI) is one of the most popular multilevel inverter topologies. This topology is synthesized with some series-connected identical H-bridge cells. CMI requires several isolated dc sources which brings about some difficulties when dealing with this type of inverter. This paper addresses the problem by proposing a switched-capacitor (SC)-based CMI. The proposed topology, which is referred to as switched-capacitor single-source CMI (SCSS-CMI), makes use of some capacitors instead of the dc sources. Hence, it requires only one dc source to charge the employed capacitors. Usually, the capacitor charging process in a SC cell is companied by some current spikes which extremely harm the charging switch and the capacitor. The capacitors in SCSS-CMI are charged through a simple auxiliary circuit which eradicates the mentioned current spikes and provides zero-current switching condition for the charging switch. A computer-aid simulated model along with a laboratory-built prototype is adopted to assess the performances of SCSS-CMI, under different conditions. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

In this paper, a family of automatic interleaved Dickson switched-capacitor converters (AIDSCC) and its zero-voltage switching (ZVS) resonant configuration are proposed. Different from the traditional Dickson switched-capacitor converter, the AIDSCC has symmetrical configuration with the features of automatic interleaved input current, small output voltage ripple, and lower peak capacitor voltage stress. To improve the line regulation capability, one small resonant inductor is inserted and two bulky capacitor banks are replaced by two much smaller resonant capacitors, forming the resonant AIDSCC. The transistors are ZVS turned on and diodes are zero-current switching turned off by operating above the resonance. With frequency modulation within a reasonable range, the voltage-gain range of the resonant AIDSCC is expanded significantly, while sacrificing the maximum efficiency due to the higher conduction loss. A 3X AIDSCC and a 3X resonant AIDSCC below 140 W were built to verify the analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a novel 11-level improved active-neutral-point-clamped (11L-IANPC) converter for ground power unit (GPU) application. This hybrid topology consists of the 5L-ANPC and the proposed low-voltage submodule. The proposed 11L-IANPC converter possesses only one flying capacitor (FC) and reduced number of high-frequency switches. Hence, voltage diversity and ratings, stored energy, and the number of costly and bulky FCs are significantly decreased. Moreover, operating the augmented submodule at the low voltage and power leads to doubling the number of output voltage levels, whereas the low extra cost and size are imposed on the proposed converter. In addition, suggested sensorless switching method leads to self-balancing of FC and significantly amends the output voltage frequency spectrum. These improvements cause significant reduction in control complexity of the proposed 11L-IANPC converter, remarkable decrease in size of the bulky and costly output LC filter, and improving the dynamic and steady-state performance of the proposed static GPU. The simulation and experimental results validate the feasibility of the proposed converter as well as its suggested modulation and control method. [ABSTRACT FROM AUTHOR]

Usually, the parallel-compensated inductive power transfer (IPT) topology fed by a current-source inverter is controlled through variable switching frequency and fixed 50% duty cycle method. This enables the system to operate at resonance frequency, which drifts due to load and other parameter variations. Owing to this control constraint, the load requirements are fulfilled by adding extra dc–dc chopper at the output. This paper presents a new control technique for a parallel–series/series IPT network, fed from a full-bridge current-source inverter to meet the load demand directly by an inverter. Therefore, the extra chopper stage at the output side of the converter is eliminated. The control goals are achieved through a two-loop control method, where the inner input current loop controls the source current and the outer output current loop meets the load requirements. The detailed steady-state operation, converter design, small-signal modeling, and control are reported, and experimental results obtained from a 1.6-kW lab prototype are included to verify the mathematical analysis. [ABSTRACT FROM AUTHOR]

The conventional design of voltage-source power converters is based on a two-level half-bridge configuration and the selection of power devices designed to meet the full application specifications (voltage, current, etc.). This leads to the need to design and optimize a large number of different devices and their ancillary circuitry and prevents taking advantage from scale economies. This paper proposes a paradigm shift in the design of power converters through the use of a novel configurable device consisting on a matrix arrangement of highly optimized switching cells at a single voltage class. Each switching cell consists of a controlled switch with antiparallel diode together with a self-powered gate driver. By properly interconnecting the switching cells, the switching-cell array (SCA) can be configured as a multilevel active-clamped leg with a different number of levels. Thus, the SCA presents adjustable voltage and current ratings, according to the selected configuration. For maximum compactness, the SCA can be conceived to be only configurable by the device manufacturer upon the customer needs. For minimum cost, it can also be conceived to be configurable by the customer, leading to field-configurable SCAs. Experimental results of a 6 × 3 field-configurable SCA are provided to illustrate and validate this design approach. [ABSTRACT FROM AUTHOR]

In this paper, a family of step-up resonant switched-capacitor converters (RSCs) with a continuously adjustable conversion ratio is proposed based on the Cuk dual-resonance core (DRC) featuring two resonant paths. By adopting the on-time fixed frequency modulation, the two resonant paths can conduct simultaneously and satisfy the charge balance of the flying capacitor during the overlapping period. As a result, the conversion ratio—upper bounded by two determined by the circuit configuration—can vary continuously and efficiently even at the light load condition (1/10 of the rated power). A comprehensive analysis—the operation principle, voltage-gain curve, and voltage/current stresses—about the DRC is given. In addition, the Cuk DRC was extended to the series–parallel switched-capacitor converter (SCC), Fibonacci SCC, and voltage doubler to form a family of step-up RSCs, whose voltage-gain curves of different topologies are derived. Moreover, a characteristic comparison between the Cuk DRC and the traditional “direct” and “indirect” resonant core is given. Then, a 48 to 62–94.6 V resonant core with peak efficiency 97.8% and maximum power 120 W under the open loop condition was built. The analyses were verified by both experimental and simulation results. [ABSTRACT FROM AUTHOR]

A new class of impedance networks is proposed in this paper. The proposed coupled-inductors-based impedance cells, called the series and the tapped switched-coupled-inductors, are employed within the (quasi) switched boost networks. The achieved impedance networks based on the proposed cells offer very high conversion gains with less-than-unity turn ratios (n < 1), which simplifies the realization of the magnetic element and at the same time reduces the number and size of passive components. The high boosting capability is achieved with small shoot-through durations that bring some additional advantages, such as low ratings of switching devices. The circuit analysis and operation concepts as well as a design procedure for the components of the proposed impedance networks are presented. Theoretical achievements are confirmed through experiments on a 220 W dc–dc converter laboratory setup. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

The five-level nested neutral-point-clamped (5L-NNPC) converter is one of the most promising topologies for medium-voltage (2.3–7.2 kV) high-power applications such as medium-voltage drives, wind energy conversion systems, and grid-connected systems. The 5L-NNPC requires a fewer number of switching devices, freewheeling and clamping diodes, and flying capacitors compared to the existing five-level multilevel converters. In the 5L-NNPC topology, each flying capacitor voltage is regulated at one-fourth of the dc-bus voltage to obtain the five-level operation. Due to the lack of redundant switching states, it is difficult to control the flying capacitor voltages by using the pulse-width-modulation-based classical control methods. This paper proposes a model-predictive current control (MPCC) approach to control the flying capacitor voltages along with the output currents of the 5L-NNPC converter. The discrete-time model of 5L-NNPC is developed to implement the MPCC scheme. The simulation and experimental studies are conducted to verify the dynamic and steady-state performance of 5L-NNPC with the MPCC scheme. The performance of the proposed MPCC approach is compared with the conventional space-vector-modulation-based voltage-balancing approach. Furthermore, the flying capacitor voltage control capability of MPCC is verified at different load power factors. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

This paper presents an overview of resonant and hybrid switched-capacitor converters with a particular focus on multimode operation. The multimode approach is discussed as a tool to affect high efficiency and power density across a wide load range, provide variable regulation, and, as a general framework, to conceptualize the advantages and opportunities of the approach compared to more traditional dc–dc converters. A general analysis is provided to quantify the advantage of hybrid and resonant converters that factors in the tradeoffs between size and loss in the magnetic component and voltage stress on the active devices. A broader set of operating modes is presented that spans continuous and discontinuous conduction and includes resonant, quasi-resonant, and more traditional buck- or boost-like operation. A prototype flying-capacitor multilevel converter is presented to demonstrate the variety of operating modes and motivate important considerations such as voltage balance on the flying capacitors. [ABSTRACT FROM AUTHOR]

Recently, inductive energy storage systems have attracted interests due to high energy densities. The high-temperature superconducting pulsed-power supply (HTSPPS) is one inductive PS topology for electromagnetic launching system. The topology can achieve a high amplitude load current and cut down the electrical losses due to the zero resistance characteristic of superconducting inductors. However, in this topology, the integrated gated commuted thyristor is used as a switch and cannot withstand high current, which limits the expansion of the system. Besides, it has significant current amplification ability as a single unit, but one module cannot provide sufficient amplitude and appropriate pulsewidth for the load current of the electromagnetic launching. In this paper, by applying the principle of inverse current commutation with semiconductor devices (ICCOS) in the HTSPPS, a novel circuit topology called HTSPPS with ICCOS is presented. This topology is analyzed and the multiple modules system is established. Simulation results show that the HTSPPS with ICCOS exceeds the current limitations of the original one and ensures the reliable cutting off of the main switch. It has potential applications in the future of high-energy systems while reducing the cost greatly. By asynchronous cooperative triggered discharge of the multiple HTSPPS with ICCOS modules in parallel, the appropriate amplitude and flat shape current of the load can be achieved through the careful design of the trigger time. [ABSTRACT FROM AUTHOR]

This paper presents a new concept and approach for topology control and switching in distribution systems by extending the traditional circuit switching to laterals and single-phase loads. Voltage unbalance and other key performance indicators including voltage magnitudes, line loading, and energy losses are used to characterize and demonstrate the technical value of optimizing system topology on a per-phase basis in response to feeder conditions. The near-optimal per-phase topology control is defined as a series of hierarchical optimization problems. The proposed approach is applied to IEEE 13-bus and 123-bus test systems for demonstration, which included the impact of integrating electric vehicles (EVs) in the test circuit. It is concluded that the proposed approach can be effectively leveraged to improve voltage profiles with electric vehicles, the extent of which depends on the performance of the base case without EVs. [ABSTRACT FROM AUTHOR]

Inductive power transfer (IPT) for battery charging applications has significant advantages over the traditional plug-in system. Since misalignment between the primary and secondary windings is inevitable, it is of significance to improve the misalignment tolerance of IPT systems with constant-current (CC) and constant-voltage (CV) outputs for battery charging. In this paper, the load-independent output characteristic of the hybrid topology and the function switching between CC and CV of the reconfigurable topology are analyzed. Besides, a hybrid and reconfigurable IPT system with 3-D misalignment tolerance for CC and CV outputs is proposed, simplifying or even canceling control schemes. Moreover, a novel parametric design method is given for the IPT system, which can suppress the fluctuation of the output voltage/current within a certain range of misalignment. In order to validate the performance of the proposed topology, a 1-kW prototype is built, and the corresponding experiments are carried out. In the CC/CV mode, the system can operate with the longitudinal misalignment to 50% when the load varies from 36 to 480 Ω, and the fluctuation of the output current/voltage is within 5%. Similarly, the misalignment in Y- and Z-axis is 12.5% and 33.3%, respectively. [ABSTRACT FROM AUTHOR]

This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifier is driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD $_{i}$ < 8%) under variation of the utility-line input voltage from 180 to 250  ${{V}}_{{\rm{rms}}}$. These experimental results demonstrate the feasibility of the proposed LED scheme. [ABSTRACT FROM AUTHOR]

Switched-capacitor (SC) converters have drawn more and more attention in recent years due to their unique advantages. The accurate analysis methods will fully determine an SC converter's steady-state and dynamical performance. Proper design of SC converters requires full understanding of all impacts on circuit operation including steady-state and dynamical performance. Some previous modeling methods for SC converters have established a popular static model for SC converters which is composed of an ideal transformer and equivalent output resistance. This paper presents a dynamic capacitor ampere-second balance transient calculation modeling method. The instantaneous state of input voltage, instantaneous state of output voltage, instantaneous state of voltage of flying capacitor, “on time” and “off time,” as well as switching period are all included in the proposed model. The proposed modeling method was applied in both the dual-phase SC converters and the two-switch boosting SC converters. This modeling method was validated by the simulation and experimental results. The proposed model can be used to accurately predict and optimize the performance in the design phase for the low and high power SC converters. Based on the proposed modeling method, the SC converters could be controlled by a variable frequency control method. [ABSTRACT FROM AUTHOR]

Owing to low cost, small size, and low weight, transformerless inverters became prominent in single-phase grid connected photovoltaic (PV) systems. Key issues pertaining to these inverters include suppression of common mode (CM) leakage current and improvement of conversion efficiency. Achieving higher efficiency in single-phase grid-connected photovoltaic systems depends on the number of stages involved in feeding power to the grid, predominantly, if the PV array voltage is less than the peak value of the grid voltage. In this paper, an integrated dc–dc converter based grid-connected transformerless PV inverter is proposed which is aimed at maintaining high efficiency, even if the PV array voltage falls below the peak value of grid voltage (efficient operation at an extended input voltage range). A modulation strategy is discussed in order to minimize the flow of CM leakage current. Further, the efficiencies of certain transformerless inverter topologies are analyzed and compared with that of the proposed topology. Detailed simulation studies are carried out in MATLAB/Simulink environment to verify the analysis. Experimental results for a scaled down laboratory prototype are included as a proof-of-concept to validate the claims. [ABSTRACT FROM AUTHOR]

In this paper, a fifth-order boost point-of-load converter is developed by cascading a modified fourth-order boost converter with a combination of L–C and diode. This topology has the following salient features: Single-switch topology, common ground between source and load, low-voltage stress across intermediate capacitors, and voltage gain same as other reported fifth-order boost converters with no common ground. Steady-state and dynamic analyses demonstrate the proposed converter's boosting feature and dynamic performance, respectively. A contoured robust Bode plot methodology is employed to design the robust voltage-mode controller to ensure load voltage regulation in the presence of uncertainties. The necessary and sufficient conditions under which the designed controller guarantees the load voltage regulation and robust stability are obtained. A step-by-step robust controller design procedure is outlined. The salient features of the proposed converter and its robust performance are studied analytically, using the MATLAB platform, and validated experimentally on a 60-W prototype module. [ABSTRACT FROM AUTHOR]