Search

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

Pulse-width-modulated (PWM) converters have been widely applied for power processing, and they are typically the stems of other types of converters, such as quasi-resonant, Z-source, and switched-inductor hybrid converters. Development of PWM converters has been spanning over a century, starting from the buck converter. The well-known PWM converters include buck, boost, buck–boost, Ćuk, single ended primary inductive converter (SEPIC), zeta, Z-source, quasi-Z source, etc. Many attempts have been proposed to develop these converters based mostly on canonical cell concepts and by introducing extra LC filters to the cells. This paper presents an enhancement to the layer and graft schemes by introducing the ideas of dc voltage/current offsetting, capacitor/inductor component splitting, diode grafting, and inverse operation of PWM converters. The PWM converters, which can be operated in continuous conduction mode (CCM) or discontinuous conduction mode (DCM), therefore can be synthesized systematically according to decoded transfer gains. Decoding and synthesizing PWM converters uniquely bridge transfer gains to converter topologies and provide readers a comprehensive understanding of PWM-converter evolution from the original converter, the buck converter. Additionally, in this paper, the Ćuk, SEPIC, and zeta converters all with the same transfer gain of $D/(1 - D)$ are proved to be equivalent to the buck–boost converter with an extra LC filter. For further illustrating the proposed approaches, various types of Z-source converters, switched-capacitor/switched-inductor hybrid converters, and a single-stage interleaved converter are reviewed, and new PWM converters are developed. [ABSTRACT FROM AUTHOR]

High step-down voltage conversion is necessary to bridge the voltage gap between main power converters and low-voltage auxiliary electronics in power conversion systems. Switched capacitor converters (SCCs) are an attractive candidate as a high step-down converter, but their poor voltage regulation capability may limit their applications. Pulsewidth modulation (PWM) SCCs with adjustable high step-down voltage conversion are proposed in this paper. The proposed PWM SCCs can be derived from traditional SCCs by replacing an energy transfer capacitor with a switched-capacitor-inductor (SCL) cell that comprises inductors, capacitors, and diodes to realize PWM-controllable voltage conversion. The voltage step-down ratio of the proposed PWM SCCs is not only PWM controllable but also adjustable with structures of SCCs and SCL cells. Two representative PWM SCCs were taken as examples to perform the operational analysis. The prototypes of both representative PWM SCCs were built and tested to demonstrate the proposed concept. [ABSTRACT FROM AUTHOR]

In this paper, a novel direct ac–ac converter based on the coupled inductor Z-source networks is proposed that offers a wide range of buck–boost operation. A total of two Z-source networks, called the coupled switched inductor and the modified switched coupled inductor, are employed that enable the ac–ac converter to deliver a wide voltage range. The proposed converter with both networks provides free-wheeling current paths for the inductors currents during the state transitions, which results in solving the commutation problems and the need for snubber circuits. A simple switching strategy is then proposed that helps to share a common magnetic core between the coupled inductors. For any particular voltage gain, the proposed structures require a smaller duty cycle compared to the conventional ones; therefore, a smaller inductance is required. Simulation and experimental results are provided to confirm the theoretical achievements. [ABSTRACT FROM AUTHOR]

Recent power systems, such as renewable energy systems consisting of solar panels and rechargeable batteries, contain multiple power sources and need multiple converters in proportion to the number of power sources, resulting in increased system complexity and cost. This paper proposes a multiport converter (MPC) integrating a bidirectional PWM converter and series-resonant converter. Not only is the switch count halved with the proposed MPC, but also magnetic components can be integrated, reducing the circuit complexity and volume. A 150-W prototype of the proposed MPC was built for the experimental verification. The measured voltage conversion characteristics and transient responses demonstrated that the proposed MPC could control load and battery voltages independently by pulse width modulation and pulse frequency modulation controls, respectively. [ABSTRACT FROM AUTHOR]

Soft switching pulse-width modulation (PWM) dc–dc full-bridge converter with controlled rectifier on the secondary side of the high-frequency power transformer is presented in this paper. An active secondary switch, including new nondissipative passive energy recovery turn-off snubber on the secondary side and modified PWM control algorithm, provide conditions for zero-voltage and zero-current turn-on and zero-current turn-off of IGBT transistors on the primary side of the high-frequency dc–dc converter. The simple passive energy recovery snubber ensures also zero-voltage turn-off of the transistor on the secondary side of the power transformer. The principle of operation is explained and analyzed and consequently verified on a 2 kW, 50 kHz laboratory model of the converter. [ABSTRACT FROM PUBLISHER]

Interleaved converter legs are typically modulated with individual carriers per leg and phase-shifted pulse width modulation (PS-PWM) as it facilitates current balancing amongst the legs. Phase-disposition PWM (PD-PWM), despite the better harmonic performance, cannot be directly used due to the resulting current imbalance that may damage the converter. This paper addresses the current sharing issue and proposes a sorting algorithm implementation that enables single-carrier PD-PWM technique for interleaved two-level converter legs. An extension of the proposed algorithm through a switching state feedback loop, limiting the average switching frequency, is also developed. In both cases, the output current is of high quality and shared amongst the phase-legs, while the deviation between the phase-leg currents is well regulated. Simulation results demonstrate the general function of method for multiple interleaved legs as well as its current sharing capabilities for high-power applications. Experimental results from a low-power laboratory prototype validate the operation of the proposed approach. [ABSTRACT FROM PUBLISHER]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

In this paper, a new zero-voltage switching and resonant core reset pulse width modulation forward converter with a simple auxiliary circuit is introduced. The proposed auxiliary circuit can be applied to both single-switch and two-switch forward converters. The main and the auxiliary mosfets of the proposed converters operate under soft switching condition independent of line and load variation. Also, due to the capability of operating at duty cycles higher than 0.5, the proposed converters can be used for wide input voltage applications. In comparison to the existing zero-voltage transition (ZVT) forward converters, this auxiliary circuit has low number of components and also does not require any additional magnetic element which has improved the power density. The proposed converter is compared with exiting ZVT forward converters in details. The converter steady-state operation is analyzed and various operating modes are explained. Also, in addition to a design example, a comprehensive design procedure is presented. The experimental results of a laboratory prototype of the converter with 85–180 V input voltage and 24 V output voltage at 150 W are provided which verify the theoretical analysis and confirm the converter operation. The overall efficiency of 93.5% is achieved for the proposed converter at full load. [ABSTRACT FROM PUBLISHER]

The main objective of this paper is to examine the operation of a fundamental buck-based three-phase single-stage ac–dc full-bridge converter. In this paper, the operation of this fundamental converter is explained and analyzed, and a procedure for the design of its key components is derived and demonstrated with an example. The performance and characteristics of the converter are shown with experimental results that have been obtained from a prototype, and general concluding remarks comparing buck-based and boost-based three-phase single-stage ac–dc full-bridge converters are made. [ABSTRACT FROM PUBLISHER]

This paper proposes a pulse-width modulation three-level converter with reduced filter size using two transformers. The proposed converter has many advantages. All switches sustain only the half of the input voltage and since the secondary rectified voltage is a three-level waveform, the output filter inductor can be reduced. Also, because of the power sharing of transformer and reduced output inductor, high efficiency can be obtained. The operational principle, analysis, and design considerations of the proposed converter are presented in this paper. The validity of this study is confirmed by the experimental results from a prototype with 600 W, 500-600 V input, and 60 V output. [ABSTRACT FROM AUTHOR]

In this paper for power factor correction (PFC), a modified Landsman converter is introduced. The application is targeted for high-brightness (HB) projection application with brightness control for HB red–green–blue (HB-RGB) light-emitting diode (LED). A pulse-width modulation (PWM) technique is used for intensity control to achieve brightness control of the LED driver. The proposed PFC converter is used to feed a dual output flyback dc–dc converter that supplies power to the forced cooling unit and the LED module with galvanic isolation. The brightness control of LED is performed by synchronous buck converter. The modified Landsman converter operates in discontinuous output inductor current mode for PFC at universal ac mains. A prototype of the proposed LED driver is experimentally verified. The performance of proposed driver is evaluated at full and light-load condition for universal ac mains (90–265 V) over a full range of brightness. The power quality parameters are found within the acceptable limits of harmonic standard IEC 61000-3-2 for universal ac mains. [ABSTRACT FROM PUBLISHER]

In this paper, the switching cell concept is extended to isolated ac–ac converters, and a highly reliable double step-down ac–ac converter is proposed with high-frequency transformer (HFT) isolation. By using the switching cell structure and coupled inductors, the proposed converter has no commutation problem as it is immune from both short-circuit and open-circuit problems, even when all the switches are turned on or turned off, simultaneously. Therefore, it does not require pulse width modulation dead times along with bulky and lossy RC snubbers or voltage-sensing circuitry to implement soft-commutation strategies, resulting in high reliability and high quality output waveforms. The HFT in the proposed converter provides electrical isolation and safety which is required in applications such as dynamic voltage restorer (DVR), solid-state transformer (SST), etc., without the need for external bulky line frequency transformer. Moreover, all the passive components experience twice the switching frequency; therefore, their size can be reduced. The proposed converter is very suitable for application as DVR, to compensate both voltage sags and swells, owing to its ability to provide both inverting and noninverting outputs. A detailed theoretical analysis and operation of the proposed ac–ac converter are provided, and its applications as DVR and SST are also discussed. Experimental results with scaled-down prototype are also provided to verify its performance. [ABSTRACT FROM AUTHOR]

A single-phase inverting buck–boost ac–ac converter is proposed in this paper. The proposed converter has no shoot-through and dead-time problems and, like conventional dc–dc converters, it can be operated with simple pulse width modulation (PWM) control. It offers high frequency and high efficiency operation because high speed mosfet can be used as switching device without the reverse recovery issues and losses of its body diode. The proposed converter features quasi-continuous input and output currents, high input power factor, low total harmonic distortion of input and output currents, and high efficiency. A 460 W laboratory prototype was constructed and tested with interleaved and complementary PWM controls using a resistive and inductive load. Detailed experimental results are provided to show the novelty of the proposed converter. Experimental results confirmed that the proposed converter can obtain 93.8% efficiency at 60 kHz switching frequency. [ABSTRACT FROM PUBLISHER]

This paper proposes single-phase direct pulsewidth modulation (PWM) buck-, boost-, and buck–boost-type ac–ac converters. The proposed converters are implemented with a series-connected freewheeling diode and MOSFET pair, which allows to minimize the switching and conduction losses of the semiconductor devices and resolves the reverse-recovery problem of body diode of MOSFET. The proposed converters are highly reliable because they can solve the shoot-through and dead-time problems of traditional ac–ac converters without voltage/current sensing module, lossy resistor–capacitor (RC) snubbers, or bulky coupled inductors. In addition, they can achieve high obtainable voltage gain and also produce output voltage waveforms of good quality because they do not use lossy snubbers. Unlike the recently developed switching cell (SC) ac–ac converters, the proposed ac–ac converters have no circulating current and do not require bulky coupled inductors; therefore, the total losses, current stresses, and magnetic volume are reduced and efficiency is improved. Detailed analysis and experimental results are provided to validate the novelty and merit of the proposed converters. [ABSTRACT FROM AUTHOR]

Multilevel current source converters are a smart choice for the high-power applications with low-voltage and high-current requirements. This paper presents the detailed analysis of a current source modular multilevel converter (CSMMC) and its application as a STATCOM. Various properties of CSMMC are compared with the voltage-source modular multilevel converter (VSMMC). The submodule inductance selection method and a sorting-based algorithm for inductor current balancing are proposed for CSMMC. The validity of the inductance selection method and the inductor current balancing algorithm are confirmed by the simulation of a three-phase CSMMC using PSCAD/EMTDC. The carrier phase-shifted sinusoidal pulsewidth modulation is used as the switching technique. The performance of a converter is analyzed with interleaved and noninterleaved carrier signals for the upper and lower arms. Results show that CSMMCs and corresponding VSMMCs have analogous features. Hence, the development on VSMMCs can be used for reference to CSMMCs and vice-versa. Furthermore, the control designs for CSMMC-based STATCOM are presented and verified using simulations. The obtained results of the proposed STATCOM show that the steady-state and transient performance of the system are quite satisfactory. This makes the CSMMC suitable for HVDC and flexible ac transmission systems applications. [ABSTRACT FROM PUBLISHER]

This paper revisits the switched flow graph (SFG) technique. A general and unified equivalent SFG model of a three-terminal switcher encountered in regular and tapped inductor converters operating in the continuous conduction mode is proposed. The model can be applied to most PWM topologies and facilitates construction of a complete flow graph of a given converter. The approach can be helpful in theoretical analysis and derivation of analytical expressions of converter's small-signal transfer functions. The suggested methodology extends the previously proposed SFG analysis technique and alleviates the principal difficulties involved. Furthermore, the approach is straightforward and expeditious. Application guidelines and examples are presented and compared to simulation and earlier theoretical results. [ABSTRACT FROM PUBLISHER]

As electrolytic capacitor is apt to fail in power circuits, it is very important to identify its electrical parameters, mainly the equivalent series resistance (ESR) and capacitance (C). A noninvasive online identification method of capacitor's ESR and C for continuous-conduction-mode (CCM) buck converter is proposed in this paper. Based on the ac component of capacitor voltage, the calculation model is founded. By sampling the pulse width modulation signal and output voltage, the method needs no current sensor and is effective for the CCM buck converter operating at different conditions. Implementation of the identification system is presented. The tests are carried out for different aged capacitors and ambient temperatures. The experimental results validate the effectiveness of the method. [ABSTRACT FROM AUTHOR]

A hybrid switched-capacitor/interleaved boost converter able to provide a high voltage gain and to cancel the input current ripple at a preselected duty cycle was recently presented in the literature. This paper extends that work by proposing an optimized switching strategy for operating conditions at other values of duty cycle. The switching strategy effect on the converter's voltage gain and input current ripple is quantified and compared against the performance under the conventional switching strategy. The approach is validated in the laboratory through hardware prototyping. [ABSTRACT FROM PUBLISHER]

In this paper, a simplified pulsewidth modulation with switching constraint control scheme is proposed to eliminate the circulating currents for bidirectional paralleled ac/dc converters in grid-tied system. The proposed control scheme can reduce the circulating currents and does not need additional current sensors and communication device among paralleled converters compared with conventional methods. Therefore, the paralleled system cost can be reduced. In addition, the current shaping and sharing between the paralleled converters can be well accomplished so that the overall performance of the paralleled converter system can be raised. Furthermore, the dc, ac, and self-generated circulating currents are clearly analyzed by graphics, and the synchronous circulating currents are first explored. Finally, a prototype system is constructed, and the proposed control scheme is implemented using a Spartan-3E XC3S250E FPGA. Both simulation and experimental results verify the validity of the proposed theory and control scheme. [ABSTRACT FROM PUBLISHER]

Alternating current (ac) active electronic loads (AELs) based on pulsewidth modulation (PWM) converters, capable of emulating nonlinear loads, require effective current control techniques and power stages. These two aspects of an AEL are interdependent mainly due to the presence of electromagnetic compatibility filters to reduce electromagnetic emissions. However, the filter components affect the dynamics of the system. In this context, this paper proposes a digitally implemented control strategy comprising the state feedback, robust observer, phase-locked loop, and linear current controller to cope with ac AEL applications. The control-oriented modeling and the control system design are presented. Experimental results obtained from a 10-kW three-phase three-level PWM converter prototype illustrate and demonstrate the feasibility of the proposed AEL control strategy. [ABSTRACT FROM PUBLISHER]

In this paper, a new modeling and control technique for a three-phase boost converter is presented for efficient transfer of energy from an irregular input power source to a battery storage device or a dc link. First, a circuit model for a three-phase boost converter is developed using the method of averaging, followed by a derivation of the conditions under which the pulse width modulated switching circuit exhibits a resistive behavior from the input. Based on the circuit model obtained, a new model-based feedback control scheme is presented to regulate the phase-to-phase input resistances of the circuit to desired values. The circuit can provide purely active power conversion of a band-limited input voltage source to a dc link, which is of interest in boost converters for certain energy conversion systems. Simulation and experimental results are presented that illustrate performance of the proposed modeling, feedback control, and switching scheme for a low-power application. [ABSTRACT FROM PUBLISHER]

This paper proposes a zero-voltage switching (ZVS) pulsewidth modulation (PWM) dc/dc converter with current double rectifiers to achieve ZVS for all switches under a wide range of load conditions and input voltages. Two three-level PWM circuits sharing the same power switches are adopted in the proposed converter to reduce the voltage stress of each MOSFET at Vin/2 and achieve load current sharing. Thus, the current stress and power rating at the secondary-side components are reduced. The current double rectifiers are used at the secondary side to partially cancel the output ripple current. Thus, the sizes of the magnetic components and output filter capacitance are reduced. Due to the resonant behavior by the resonant inductance and resonant capacitance at the transition interval, all switches are turned on at ZVS. The experimental results based on a 1-kW prototype are provided to verify the operation principle of the proposed converter. [ABSTRACT FROM PUBLISHER]

Considering the tradeoff between efficiency and output ripple over a wide load range, a monolithic dc–dc buck converter with switch-on-demand modulation (SODM) and switch size control (SSC) is presented in this paper. SODM achieves a hybrid mode of pulse skip and pulse width modulation (PWM) without mode detection circuit. The converter's on time is adaptively adjusted with the load demand, achieving low output voltage ripple. Detecting the output of the error amplifier by a comparator, the SSC circuit can select appropriate switch size according to load current for reducing switching loss in a light load. The threshold level of the comparator varies with respect to the amount of slope compensation, which maintains a substantially constant switch size changing point. Experimental results show that the fabricated converter with the proposed scheme achieves high efficiency from 83% to 96% over a wide load range from 10 mA to 5 A. The switch size is 1/4 of the maximum value when load current is below 1 A with 0.5-A hysteresis. Also, the measured maximum output ripple is less than 10 mV. [ABSTRACT FROM PUBLISHER]

A new 2-D random-switching pulsewidth modulation (PWM) technique is proposed to reduce the dominant harmonic clusters while retaining constant average inductor current and constant sampling frequency. The special feature of constant average inductor current can reduce the output voltage ripple. Moreover, the controller parameters of a digitally controlled power converter are not required to change, which is quite essential to digitally controlled systems. Current random PWM methods are discussed and compared with the proposed method in this paper. It will be shown that the merits of the presented method include random-switching frequency, constant sampling frequency, and constant average inductor current. An field-programmable-gate-array-based digitally controlled buck converter experimental system has been set up. The specifications of the converter include input\ voltage = 5\ \V, output\ voltage = 1.5\ \V, and switching\ frequency = 200\ \kHz. The proposed random-switching pattern is implemented by software. Experimental results demonstrate the effectiveness of the proposed random-switching pattern. [ABSTRACT FROM PUBLISHER]

This paper presents a novel power conversion topology for systems, which include a boost and bidirectional converters to control the power flows between sources, batteries, and ultracapacitors. The proposed system (multimode single-leg power converter) substitutes the boost converter and bidirectional converter with a multifunctional bidirectional converter and has cost effectiveness and fault tolerance, preserving the same energy conversion functionalities of the conventional energy conversion system. To verify the performance of the proposed system, its operations are categorized and explained to four different modes. Then, each mode of the proposed system is simulated and implemented experimentally using a prototype test bed. The results present that the proposed conversion system is feasible and applicable for a wide range of applications including alternative/renewable power systems and electric vehicles (EVs). [ABSTRACT FROM AUTHOR]

This paper proposes a cross-coupled master-slave interleaving control method for boundary conduction mode (BCM) power factor correction (PFC) converters. The natural period of every switching cycle of each channel is measured and compared to adaptively determine the master and slave converters, where a converter with a longer natural period becomes master operating in BCM, while a converter with a shorter natural period becomes slave operating in discontinuous conduction mode. The proposed method compensates disturbances within one switching cycle, guaranteeing stable 180° out-of-phase interleaving operation against any transient and disturbance. The proposed method has been implemented and tested on a 400 W interleaved BCM boost PFC prototype converter with a dedicated control IC. [ABSTRACT FROM PUBLISHER]

In this paper, an improved pulse width modulation (PWM) method for chopper-cell (or half-bridge)based modular multilevel converters (MMCs) is proposed. This method can generate an output voltage with maximally 2N+1 (where N is the number of submodules in the upper or lower arm of MMC) levels, which is as great as that of the carrier-phase-shifted PWM (CPSPWM) method. However, no phase-shifted carrier is needed. Compared with the existing submodule unified pulse width modulated (SUPWM) method, the level number of the output voltage is almost doubled and the height of the step in the staircase voltage is reduced by 50%. Meanwhile, the equivalent switching frequency in the output voltage is twice that of the conventional SUPWM method. All these features lead to much reduced harmonic content in the output voltage. What is more, the voltages of the submodule capacitors can be well balanced without any close-loop voltage balancing controllers which are mandatory in the CPSPWM schemes. Simulation and experimental results on a MMC-based inverter show validity of the proposed method. [ABSTRACT FROM AUTHOR]

A novel winding-coupled bidirectional dc/dc converter with zero-voltage-switching (ZVS) performance is proposed in this paper. In the low-voltage side, the parallel configuration is employed to share the large current and reduce the current ripple. In the high-voltage side, the series structure is adopted to sustain the high bus voltage and achieve large voltage ratio conversion. There are only two coupled inductors in the proposed interleaved bidirectional converter and their secondary windings are in series to serve as winding-coupled inductors. Furthermore, the two winding-coupled inductors can be integrated into a magnetic core to reduce the passive component numbers and improve the power density. Moreover, ZVS soft-switching operation is implemented for all the power switches to minimize the switching losses by introducing the active clamp scheme. In addition, the pulsewidth modulation plus phase-shift control strategy is employed to reduce the power MOSFET peak current and diminish the circulating losses. The duty cycle is applied to balance the voltages of both sides. The phase-shift angle is introduced to realize the power flow regulation. This decoupling control strategy is advantageous for bidirectional dc/dc conversion to realize high efficiency. Finally, a 1-kW prototype is built to verify the effectiveness of the proposed circuit. [ABSTRACT FROM AUTHOR]

Capacitor charging power supply (CCPS) is a developed technology that utilizes resonant converters topology for high power applications. This paper proposes new a capacitor charging power supply using leg-rotation control method within a phase-shifted PWM full-bridge dc/dc converter. The capacitor charging power supply was connected in series to increase output voltage. Also, the proposed system is designed with soft switching techniques in order to achieve high efficiency, and a leg-rotation control method was used to reduce the heat generated from the IGBTs. The operation of the converter and design methodology will be described. A simplified model of a high-voltage high-frequency transformer is given and the structure is designed to decrease high-voltage stress. The validity of the proposed system is then verified by experimental results. The performance test of the capacitor charging power supply was carried out with a 2 μF capacitive load with a 20 kV output voltage. [ABSTRACT FROM AUTHOR]